Loading…
Loading…
| Name | ID | Label | Description | Type | Source |
|---|---|---|---|---|---|
| PE_method_read_event | 41CE | msrc_UNKNOWN | Details | ||
| method_GetMI_SPV_CurrentSysConditionUnion | 41F1 | Remedy info. | msrc_UNKNOWN | Details | |
| method_GetMI_SPV_DiagListItem1Union | 41F2 | Remedy info. | msrc_UNKNOWN | Details | |
| method_GetMI_SPV_DiagListItem2Union | 41F3 | Remedy info. | msrc_UNKNOWN | Details | |
| method_GetMI_SPV_DiagListItem3Union | 41F4 | Remedy info. | msrc_UNKNOWN | Details | |
| method_GetMI_SPV_DiagListItem4Union | 41F5 | Remedy info. | msrc_UNKNOWN | Details | |
| method_GetMI_SPV_DiagListItem5Union | 41F6 | Remedy info. | msrc_UNKNOWN | Details | |
| set_min_bct | 44B3 | Set minimum BCT message | msrc_UNKNOWN | Details | |
| close_port | 44F3 | Close port | msrc_UNKNOWN | Details | |
| finish_transfer_log | 44F4 | End of transfer | msrc_UNKNOWN | Details | |
| read_wave_byBlock | 4591 | Read table ? | msrc_UNKNOWN | Details | |
| write_wave_byBlock | 4592 | Save table ? | msrc_UNKNOWN | Details | |
| method_init_linearisation | 459A | Init Linearisation Points | msrc_UNKNOWN | Details | |
| set_linearization_state_read_failed | 459B | Linearisation read failed | msrc_UNKNOWN | Details | |
| set_linearization_state_write_failed | 459C | Linearisation write failed | msrc_UNKNOWN | Details | |
| configuration_flag_reset_test | 4733 | Configuration Flag Reset | Commands reset the configuration flag. | msrc_UNKNOWN | Details |
| method_read_eventlogbook | 4689 | Read events | msrc_UNKNOWN | Details | |
| finish_transfer | 47D8 | End of transfer | msrc_UNKNOWN | Details | |
| read_hk_data | 47D9 | Read curve | msrc_UNKNOWN | Details | |
| applied_rerange | 1007 | Apply values | Applied values- Perform a device rerange by applying the desired Upper Range Value and Lower Range Values to the device input | msrc_UNKNOWN | Details |
| zero_trim | 1006 | Zero trim | Zero trim- Make the sensor input the new zero input reference | msrc_UNKNOWN | Details |
| return_to_normal | 1016 | Aborting return to normal | msrc_UNKNOWN | Details | |
| warning_message | 1017 | Set loop to manual | msrc_UNKNOWN | Details | |
| device_self_test | 1071 | Self test | Self Test- Commands the electronics to perform a self test. | msrc_UNKNOWN | Details |
| device_master_reset | 1072 | Device reset | Device Reset- Commands the electronics to perform a reset. This is equivalent to cycling the power off and then back on to the field device. | msrc_UNKNOWN | Details |
| transmitter_loop_test | 1023 | Loop test | Loop test- Allows the User to manually manipulate the Analog Output to a selected constant output value | msrc_UNKNOWN | Details |
| leave_fixed_current_mode | 1003 | Leaving fixed crnt mode | Leaving Fixed Current Mode- Takes the Analog Output out of a mode where the output was a constant value, and returns the output to a mode where the output tracks the input | msrc_UNKNOWN | Details |
| transmitter_dac_trim | 1024 | D/A trim | Digital to Analog Trim- Allows the calibration of a selected Analog Output with an external reference at the operating endpoints of the Analog Output | msrc_UNKNOWN | Details |
| makeItSquawk | 101B | Squawk | Make the Field Device Squawk- This causes the device to visually, audibly or mechanically alert to allow technicans to idendify it | msrc_UNKNOWN | Details |
| device_variable_trim | 1080 | Device variable trim | Device Variable Trim- Allows for the calibration measurement of a device variable to be adjusted linearly. The trim point that is sent to the device must represent the presently applied process variable value. | msrc_UNKNOWN | Details |
| trim_warning | 1081 | Trim warning | msrc_UNKNOWN | Details | |
| device_variable_trim_reset | 1083 | Device variable trim reset | Device Variable Trim Reset- Allows for the device variable to be set to its default factory trim. | msrc_UNKNOWN | Details |
| Name | ID | Label | Description | Type | Source |