Loading…
Loading…
| Name | ID | Label | Description | Type | Source |
|---|---|---|---|---|---|
| reset_device_error_codes_method | 403A | Reset Error Codes | msrc_UNKNOWN | Details | |
| warning_msg_method | 4004 | msrc_UNKNOWN | Details | ||
| change_damping_method | 403B | Change Damping | msrc_UNKNOWN | Details | |
| change_range_method | 403C | Change Range | msrc_UNKNOWN | Details | |
| post_send_configuration_method | 03F0 | Post send Configuration | msrc_UNKNOWN | Details | |
| meter_cal_method | 403D | Meter Calibration | D/A ﾄﾘﾑ (ﾃﾞｼﾞﾀﾙ/ｱﾅﾛｸﾞ ﾄﾘﾑ) - ｵﾍﾟﾚｰﾃｨﾝｸﾞ ｴﾝﾄﾞ ﾎﾟｲﾝﾄに対するｱﾅﾛｸﾞ出力と外部指示計とのｷｬﾘﾌﾞﾚｰｼｮﾝを行います。 | msrc_UNKNOWN | Details |
| turn_ON_OFF_alrm1_method | 403E | Turn On/Off | msrc_UNKNOWN | Details | |
| change_type_alrm1_method | 403F | Change Type | msrc_UNKNOWN | Details | |
| change_set_pt_alrm1_method | 4040 | Change Set Point | msrc_UNKNOWN | Details | |
| change_hysteresis_alrm1_method | 4041 | Change Hysteresis | msrc_UNKNOWN | Details | |
| turn_ON_OFF_alrm2_method | 4042 | Turn On/Off | msrc_UNKNOWN | Details | |
| change_type_alrm2_method | 4043 | Change Type | msrc_UNKNOWN | Details | |
| change_set_pt_alrm2_method | 4044 | Change Set Point | msrc_UNKNOWN | Details | |
| change_hysteresis_alrm2_method | 4045 | Change Hysteresis | msrc_UNKNOWN | Details | |
| factory_restore_method | 4046 | Factory Restore | Factory restore will restore factory calibrated parameters. Please re-range the unit and power cycle the unit. | msrc_UNKNOWN | Details |
| zero_trim_method | 4047 | ｾﾞﾛ ﾄﾘﾑ | ｾﾞﾛ ﾄﾘﾑ - ｾﾝｻｰに基準ｾﾞﾛを入力して補正します。 | msrc_UNKNOWN | Details |
| burst_sel_1_method | 4048 | Burst Mode | msrc_UNKNOWN | Details | |
| cmd_option_1_method | 4049 | Burst Options | msrc_UNKNOWN | Details | |
| burst_sel_2_method | 404A | Burst Mode | msrc_UNKNOWN | Details | |
| cmd_option_2_method | 404B | Burst Options | msrc_UNKNOWN | Details | |
| burst_sel_3_method | 404C | Burst Mode | msrc_UNKNOWN | Details | |
| cmd_option_3_method | 404D | Burst Options | msrc_UNKNOWN | Details | |
| two_pt_cal_method | 404E | Calibration | Calibrate Sensor with Two Point within LRV and URV. Please remove loop from automatic control. Use user manual for more details. | msrc_UNKNOWN | Details |
| four_pt_cal_method | 404F | Calibration | Calibrate Sensor with Four Point within LRV and URV. Please remove loop from automatic control. Use user manual for more details. | msrc_UNKNOWN | Details |
| status_post_read_method | 4000 | msrc_UNKNOWN | Details | ||
| status_post_read | 4072 | ﾉｰﾏﾙ ﾓｰﾄﾞに戻します | msrc_UNKNOWN | Details | |
| status_post_read_abc | 4074 | ﾉｰﾏﾙ ﾓｰﾄﾞに戻します | msrc_UNKNOWN | Details | |
| go_back | 4073 | msrc_UNKNOWN | Details | ||
| return_to_normal | 1016 | ﾉｰﾏﾙ ﾓｰﾄﾞに戻します | msrc_UNKNOWN | Details | |
| leave_fixed_current_mode | 1003 | 固定電流ﾓｰﾄﾞを終ります | 現在の固定ﾓｰﾄﾞを終了 - ｱﾅﾛｸﾞ出力を定数値のﾓｰﾄﾞから移行させ, 出力が入力に応じて変わるﾓｰﾄﾞに戻します。 | msrc_UNKNOWN | Details |
| warning_message | 1017 | ﾙｰﾌﾟをﾏﾆｭｱﾙにします | msrc_UNKNOWN | Details | |
| transmitter_loop_test | 1023 | ﾙｰﾌﾟ ﾃｽﾄ | ﾙｰﾌﾟ ﾃｽﾄ - ｱﾅﾛｸﾞ出力をﾕｰｻﾞｰが選択した値で固定出力します | msrc_UNKNOWN | Details |
| Name | ID | Label | Description | Type | Source |