HART设备字典

Loading…

引用ID	字符串
0	ZR402G
1	Cell failure
2	HT warm up fail
3	Cell HT too high
4	Cell HT too low
5	EEPROM failure
6	ADC failure
7	Excess input TC
8	Excess input CJ
9	Excess input AI
10	CJ temp too high
11	CJ temp too low
12	Low battery
13	Cal. zero error
14	Cal. span error
15	Cal. stabl error
16	CellImp too high
17	AO is holding
18	AO 1 is testing
19	AO 2 is testing
20	Cal. gas too low
21	Changing AO rnge
22	Process gas fail
23	DO 1 is active
24	DO 2 is active
25	DO 3 is active
26	DO 4 is active
27	Warming up
28	Calibrating
29	Blowing
30	Purging(calib)
31	Purging(blow)
32	Maintenance
33	Oxygen
34	O2 Sensor - measures oxygen concentration
35	Humidity
36	02 Sensor - Humidity is calcurated by oxygen concentration
37	Mixing ratio
38	O2 Sensor - Mixing ratio is calcurated by oxygen concentration
39	Cell temp
40	Oxygen cell temperature
41	CJ temp
42	Cold junction temperature
43	AI Temp
44	Analog Input temperature
45	Cell mV
46	O2 Cell mV
47	TC mV
48	O2 Cell thermocouple mV
49	CJ sensr
50	ohm/mV reading from cold junction sensor
51	AI-mA
52	mA reading from temperature transmitter
53	Dynamic var
54	Analog outputs
55	Maximum value
56	Maximum value of oxygen
57	Year(max)
58	Occurred at: year of maximum value
59	Month(max)
60	Occurred at: month of maximum value
61	day(max)
62	Occurred at: day of maximum value
63	Hour(max)
64	Occurred at: hour of maximum value
65	Min.(max)
66	Occurred at: minute of maximum value
67	Minimum value
68	Minimum value of oxygen
69	Year(min)
70	Occurred at: year of minimum value
71	Month(min)
72	Occurred at: month of minimum value
73	day(min)
74	Occurred at: day of minimum value
75	Hour(min)
76	Occurred at: hour of minimum value
77	Min.(min)
78	Occurred at: minute of minimum value
79	Average value
80	Average value of oxygen
81	HiHi alarm
82	HiHi alarm by oxygen
83	HiHi SP
84	HiHi alarm setpoint of oxygen
85	Hi alarm
86	Hi alarm by oxygen
87	Hi SP
88	Hi alarm setpoint of oxygen
89	Lo alarm
90	Lo alarm by oxygen
91	Lo SP
92	Lo alarm setpoint of oxygen
93	LoLo alarm
94	LoLo alarm by oxygen
95	LoLo SP
96	LoLo alarm setpoint of oxygen
97	Hysteresis
98	Alarm Hysteresis value of oxygen
99	Delay time
100	Alarm delay time value of oxygen
101	O2 value
102	.2f
103	.0f
104	3.0f
105	log
106	logarithm
107	O2 output
108	4.2f
109	7d
110	Max(o2)
111	Maximum value of oxygen concentration
112	Max year(o2)
113	2d
114	Max month(o2)
115	Max day(o2)
116	Max hour(o2)
117	Max minute(o2)
118	Min(o2)
119	Minimum value of oxygen concentration
120	Min year(o2)
121	Min month(o2)
122	Min day(o2)
123	Min hour(o2)
124	Min minute(o2)
125	Ave oxygen
126	Average value of oxygen concentration
127	LoLo alarm(oxy)
128	OFF
129	ON
130	Lo alarm(oxy)
131	Hi alarm(oxy)
132	HiHi alarm(oxy)
133	HiHi SP(oxy)
134	.1f
135	5.1f
136	Hi SP(oxy)
137	Lo SP(oxy)
138	LoLo SP(oxy)
139	Hysteresis(oxy)
140	3.1f
141	O2 Sensor - Humidity is calcurated by oxygen concentration
142	Maximum value of humidity concentration
143	Minimum value of humidity concentration
144	Average value of humidity concentration
145	HiHi alarm by humidity concentration
146	HiHi alarm setpoint of humidity concentration
147	Hi alarm by humidity concentration
148	Hi alarm setpoint of humidity concentration
149	Lo alarm by humidity concentration
150	Lo alarm setpoint of humidity concentration
151	LoLo alarm by humidity concentration
152	LoLo alarm setpoint of humidity concentration
153	Alarm hysteresis value of humidity concentration
154	Alarm delay time value of humidity concentration
155	Humidity value
156	Humidity output
157	Max(H2O)
158	Max year(H2O)
159	Max month(H2O)
160	Max day(H2O)
161	Max hour(H2O)
162	Max minute(H2O)
163	Min(H2O)
164	Min year(H2O)
165	Min month(H2O)
166	Min day(H2O)
167	Min hour(H2O)
168	Min minute(H2O)
169	Ave humid
170	LoLo alarm(hum)
171	Lo alarm(hum)
172	Hi alarm(hum)
173	HiHi alarm(hum)
174	HiHi SP(hum)
175	Hi SP(hum)
176	Lo SP(hum)
177	LoLo SP(hum)
178	Hysteresis(hum)
179	Mixing
180	Maximum value of mixing ratio
181	Minimum value of mixing ratio
182	Average value of mixing ratio
183	HiHi Alarm by mixing ratio
184	HiHi Alarm setpoint of mixing ratio
185	Hi Alarm by mixing ratio
186	Hi Alarm setpoint of mixing ratio
187	Lo Alarm by mixing ratio
188	Lo Alarm setpoint of mixing ratio
189	LoLo Alarm by mixing ratio
190	LoLo Alarm setpoint of mixing ratio
191	Alarm hysteresis value of mixing ratio
192	Alarm delay time value of mixing ratio
193	kg/kg
194	Mixing ratio value
195	.3f
196	5.3f
197	Mixing output
198	Max(mix)
199	.4f
200	Max year(mix)
201	Max month(mix)
202	Max day(mix)
203	Max hour(mix)
204	Max minute(mix)
205	Min(mix)
206	Min year(mix)
207	Min month(mix)
208	Min day(mix)
209	Min hour(mix)
210	Min minute(mix)
211	Ave mixing
212	LoLo alarm(mix)
213	Lo alarm(mix)
214	Hi alarm(mix)
215	HiHi alarm(mix)
216	HiHi SP(mix)
217	Hi SP(mix)
218	Lo SP(mix)
219	LoLo SP(mix)
220	Hysteresis(mix)
221	AO Damp
222	ZrO2 cell temperature
223	O2 Cell temp
224	AI temp
225	ZrO2 cell mV
226	ZrO2 cell TC mV
227	Cell TC mV
228	CJ snsr
229	Cold Junction sensor
230	AI mA
231	Analog Input Current(mA)
232	Cal logs
233	latest
234	latest calibration Log
235	2nd
236	2nd calibration Log
237	3rd
238	3rd calibration Log
239	4th
240	4th calibration Log
241	5th
242	5th calibration Log
243	6th
244	6th calibration Log
245	7th
246	7th calibration Log
247	8th
248	8th calibration Log
249	9th
250	9th calibration Log
251	Oldest
252	Oldest calibration Log
253	log1-zero
254	log1-span
255	log1-day
256	log1-month
257	log1-year
258	log1-hour
259	log1-min
260	log2-zero
261	log2-span
262	log2-day
263	log2-month
264	log2-year
265	log2-hour
266	log2-min
267	log3-zero
268	log3-span
269	log3-day
270	log3-month
271	log3-year
272	log3-hour
273	log3-min
274	log4-zero
275	log4-span
276	log4-day
277	log4-month
278	log4-year
279	log4-hour
280	log4-min
281	log5-zero
282	log5-span
283	log5-day
284	log5-month
285	log5-year
286	log5-hour
287	log5-min
288	log6-zero
289	log6-span
290	log6-day
291	log6-month
292	log6-year
293	log6-hour
294	log6-min
295	log7-zero
296	log7-span
297	log7-day
298	log7-month
299	log7-year
300	log7-hour
301	log7-min
302	log8-zero
303	log8-span
304	log8-day
305	log8-month
306	log8-year
307	log8-hour
308	log8-min
309	log9-zero
310	log9-span
311	log9-day
312	log9-month
313	log9-year
314	log9-hour
315	log9-min
316	log10-zero
317	log10-span
318	log10-day
319	log10-month
320	log10-year
321	log10-hour
322	log10-min
323	Which cal log
324	AO hold
325	Analog output hold mode during warming up
326	Analog output hold mode during maintenace
327	Cal.or Blow
328	Analog output hold mode during calibration or blowing
329	Error
330	Analog output hold mode when error occurs
331	Warm mode
332	4mA
333	20mA
334	Preset
335	Warm preset
336	Warming up preset-value
337	5.2f
338	Maint mode
339	Non-Hold
340	Hold
341	Maint preset
342	maintenace preset-value
343	Cal/Blow
344	Cal/Bl mode
345	Analog output hold mode during calibration or blow back
346	Cal/Bl preset
347	Calibration or blow back preset-value
348	Err mode
349	Err preset
350	Error preset-value
351	Detector
352	ZR22
353	ZO21D
354	Measure gas
355	Moisture base is wet or dry
356	Wet
357	Dry
358	Gas temp type
359	preset
360	AI
361	Cal zero(%)
362	Cal span(%)
363	Cell resp
364	Cell response time
365	3d
366	Cell imp
367	o2 cell impedance
368	Cell robus
369	Cell robustness
370	Life < 1 Month
371	Life > 3 Month
372	Life > 6 Month
373	Life > 12 Month
374	Air ratio
375	Moisture
376	RH%
377	Relative humidity
378	Dew-P
379	Dew point
380	Temp
381	Gas temperature
382	Press
383	Gas pressure
384	Date
385	Hour
386	Minute
387	Heater duty
388	Cal zero
389	Oxygen concentration value of zero calibration gas
390	6.2f
391	Cal span
392	Oxygen concentration value of span calibration gas
393	Calib mode
394	Calibartion mode
395	Manual
396	Semi-Auto
397	Auto
398	Calib point
399	Calibration point
400	Both
401	Span
402	Zero
403	Purge time(min)
404	Purge time(sec)
405	Cal time(min)
406	Calibration time(minute)
407	Cal time(sec)
408	Calibration time(second)
409	Cal Int(hour)
410	Calibration interval(hour)
411	Cal Int(day)
412	Calibration interval(day)
413	Cal start date
414	Calibration start date
415	Cal start hour
416	Calibration start hour
417	Cal start min
418	Calibration start minute
419	Blow mode
420	Blow back mode
421	No function
422	Blow purg(min)
423	Blow back purge time(minute)
424	Blow purg(sec)
425	Blow back purge time(second)
426	Blow time(min)
427	Blow back time(minute)
428	Blow time(sec)
429	Blow back time(second)
430	Blow int(hour)
431	Blow back interval(hour)
432	Blow int(day)
433	Blow back interval(day)
434	Blow start date
435	Blow back start date
436	Blow start hour
437	Blow back start hour
438	Blow start min
439	Blow back start minute
440	Relay
441	NDE
442	NE
443	Function
444	Calibration
445	Change range
446	Cal gas too low
447	Hi temp alarm
448	Blow back
449	Process up
450	Process failure
451	Active
452	DI1 is active at OPEN or CLOSE
453	CLOSE
454	OPEN
455	DI2 is active at OPEN or CLOSE
456	Cal gas press low
457	Change range
458	Calibration start
459	Process up set
460	Blow back start
461	Cal gas press Low
462	Moist content
463	m3/kg(m3)
464	Theoretical air
465	X value
466	ABS humidity
467	6.4f
468	Temp unit
469	Gas temp
470	4.0f
471	Press unit
472	Gas press
473	6.3f
474	AI urv
475	AI lrv
476	AI Hi SP
477	Ave time
478	MaxMin time
479	Warn enbl group1
480	Warn enbl group2
481	Warn enbl group3
482	Warn enbl group4
483	DI1
484	DI2
485	Test DO1
486	Test DO2
487	Test DO3
488	Test DO4
489	Test CalZrDO
490	Test CalSpDO
491	Calib Step
492	Span gas flow
493	Span gas done
494	Zero gas flow
495	Zero gas done
496	Check
497	Purging
498	Software seal
499	Break
500	Keep
501	Enable wrt passwd
502	New password
503	invalid gas code
504	invalid detector code
505	invalid temperature code
506	Calibration zero gas value too high
507	Calibration zero gas value too low
508	Calibration span gas value too high
509	Calibration span gas value too low
510	Purge time(min.) value too high
511	Purge time(min.) value too low
512	Purge time(sec.) value too high
513	Purge time(sec.) value too low
514	Calibration time(min.) value too high
515	Calibration time(min.) value too low
516	Calibration time(sec.) value too high
517	Calibration time(sec.) value too low
518	Calibration start(hour) value too high
519	Calibration start(hour) value too low
520	Calibration start(min.) value too high
521	Calibration start(min.) value too low
522	Improper calibration start date value
523	Calibration interval(day) value too high
524	Calibration interval(day) value too low
525	Calibration interval(hour) value too high
526	Calibration interval(hour) value too low
527	invalid ao hold code
528	invalid ao hold mode
529	invalid hihi alarm code
530	invalid hi alarm code
531	invalid lo alarm code
532	invalid lolo alarm code
533	Now time(hour) value too high
534	Now time(hour) value too low
535	Now time(min.) value too high
536	Now time(min.) value too low
537	Improper now time(date) value
538	moist content value too high
539	moist content value too low
540	theoretical air value too high
541	theoretical air value too low
542	X value too high
543	X value too low
544	Absolute humidity atm value too high
545	Absolute humidity atm value too low
546	Temperature value too high
547	Temperature value too low
548	Pressure value too high
549	Pressure value too low
550	Blow back time(min.) value too high
551	Blow back time(min.) value too low
552	Blow back time(sec.) value too high
553	Blow back time(sec.) value too low
554	Blow back purge time(min.) value too high
555	Blow back purge time(min.) value too low
556	Blow back purge time(sec.) value too high
557	Blow back purge time(sec.) value too low
558	Blow back start(hour) value too high
559	Blow back start(hour) value too low
560	Blow back start(min.) value too high
561	Blow back start(min.) value too low
562	Improper blow back start date value
563	Blow back interval(day) value too high
564	Blow back interval(day) value too low
565	Blow back interval(hour) value too high
566	Blow back interval(hour) value too low
567	AI lower range value too high
568	AI lower range value too low
569	AI upper range value too high
570	AI upper range value too low
571	Temp. SP value too high
572	Temp. SP value too low
573	Blow back is no function
574	Not set contact output
575	Not write protect mode
576	The 1st sequence for Xmtr ( Mismatch sequence? )
577	Self Test- Commands the ZR402 electronics to perform a selftest. Reports any errors that occured.
578	Master Reset- Commands the ZR402 electronics to reset and perform a selftest. Reports any errors that occured.
579	Configration
580	Test DO
581	Test Cal. DO
582	Test calibration DO(zero gas & span gas)
583	Manual calibaration
584	Manual calib.
585	Abort maual calibration
586	Start semi-auto calibaration
587	Semi-auto calib.
588	Abort calib.
589	Start blow back
590	Abort blow back
591	Max oxygen is
592	Min oxygen is
593	Max humidity is
594	Min humidity is
595	Max mixing is
596	Min mixing is
597	Calib. log
598	Read date&time
599	Write date&time
600	Purge time
601	Calibration time
602	Auto calib. timing
603	Blow purge time
604	Blow back time
605	Auto blow timing
606	Enable wrt 10min
607	Aborting
608	Exiting
609	View fld dev vars
610	View output vars
611	View PV-AO1
612	View SV-AO2
613	View TV
614	View 4V
615	View physical vars
616	View Max&Min&Ave
617	Oxygen Max&Min&Ave
618	Humid Max&Min&Ave
619	Mixing Max&Min&Ave
620	View other vars
621	Calib. constants
622	Set warning enbl
623	Read DI
624	PV range
625	SV range
626	Assign TV & QV
627	Sensors
628	CJ sensor
629	Contact output
630	Contact output 1
631	Contact output 2
632	Contact output 3
633	Contact output 4
634	Input condition
635	Contact input 1
636	Contact input 2
637	Analog input
638	Calib. condition
639	Timing
640	Blow condition
641	Alarm condition
642	Oxygen alarm
643	Humdity alarm
644	Mixing alarm
645	Other condition
646	Date & time
647	Max&Min&Ave
648	Fuel set
649	Exhaust gas
650	Device info
651	Calib info
652	Outputs info
653	Conatact info
654	Others info
655	Chng Wrt Protect
656	Upload variables
657	FMU860
658	DT
659	DVC
660	FCX
661	AS800
662	340T
663	340C
664	344
665	Siemens Micro K
666	SITRANS L
667	SIPAN PH
668	SITRANS P
669	75SMT
670	UNIDELTA
671	8320
672	SX5100
673	TSV175
674	DMU
675	3780
676	BM70
677	8u
678	Self test in progress please wait
679	Device maybe stuck in selftest.
680	Device is %{0}
681	Self Test OK
682	It will reset the master CPU, OK ?
683	Exit;Execute
684	WARN-Loop should be removed from automatic control
685	Master Reset in progress please wait
686	Device maybe stuck in master reset.
687	Master Reset OK
688	This instrument: %{0} The detector: %{1} Moisture base: %{2}
689	This instrument: %{0} The detector: %{1} Gas temp type: %{2}
690	Do you want to change data?
691	yes;no
692	NOTE-Loop may be returned to automatic control
693	Select instrument:
694	Oxygen;Humidity;Exit
695	You select oxygen model. Pressing 'OK' will send it.
696	You select humidity model. Pressing 'OK' will send it.
697	WARN-Changing this setting will return all other setting to default
698	Do you want to re-send ?
699	Now changing model
700	Select detector:
701	ZR22;ZO21D;Exit
702	Select moisture base:
703	Wet;Dry;Exit
704	The detector: %{1} Moisture base: %{2} Pressing 'OK' will send them.
705	Select gas temp type:
706	Preset;AI;Exit
707	The detector: %{1} Gas temp type: %{2} Pressing 'OK' will send them.
708	PV is %{0}
709	PV is %{0}
710	Oxygen conc. ;Humidity conc. ;Mixing ratio
711	Oxygen conc.
712	PV is %{0} Pressing 'OK' will send it.
713	PV change has been completed.
714	SV is %{0}
715	SV is %{0}
716	SV is %{0} Pressing 'OK' will send it.
717	SV change has been completed.
718	TV is %{0}
719	TV is %{0}
720	Oxygen ;Cell temp ;CJ temp ;Cell mV ;TC mV ;CJ sensr
721	Oxygen ;Humidity ;Mixing ratio ;Cell temp ;CJ temp ;Cell mV ;TC mV ;CJ sensr
722	Oxygen ;Humidity ;Mixing ratio ;Cell temp ;CJ temp ;AI temp ;Cell mV ;TC mV ;CJ sensr ;AI-mA
723	TV is %{0} Pressing 'OK' will send it.
724	TV change has been completed.
725	4V is %{0}
726	4V is %{0}
727	4V is %{0} Pressing 'OK' will send it.
728	4V change has been completed.
729	Test DO:
730	DO1;DO2;DO3;DO4;Exit
731	Test DO1:
732	OPEN;CLOSE;EXIT
733	DO1 is %{0} Press OK
734	Test DO2:
735	DO2 is %{0} Press OK
736	Test DO3:
737	DO3 is %{0} Press OK
738	Test DO4:
739	DO4 is %{0} Press OK
740	Test cal DO:
741	ZERO;SPAN;Exit
742	Test zero DO:
743	OFF;ON;EXIT
744	Zero DO is %{0} Press OK
745	Test span DO:
746	Span DO is %{0} Press OK
747	Leaving test DO.
748	Leaving test calibration DO.
749	Device is busy.
750	WARN-Device is error!
751	WARN-Calibration can't execute!
752	Device is %{0} WARN-Calibration can't execute!
753	Calibration:
754	Span;Skip;Abort
755	Check the span gas concentration. Span gas conc.: %{0} %
756	Do you want to set new value?:
757	Yes;No
758	Span gas conc.:
759	Please open span gas valve. Set the flow of span gas to 600ml/min
760	o2 value : %{0} %
761	Update o2 value;Cal done;Abort Cal
762	Now span gas done.
763	Zero;Skip;Abort
764	Check the zero gas concentration. Zero gas conc.: %{0} %
765	Zero gas conc.:
766	Please open zero gas valve. Set the flow of zero gas to 600ml/min
767	o2 value: %{0} %
768	Update o2 value;Cal done;Abort cal
769	Now zero gas done.
770	Check calibration
771	Device maybe stuck in calibration.
772	WARN-Calibration error occured.
773	Do you want to re-calibartion?:
774	Please wait purge time %{1} min %{0} s
775	WARN-Device is not selected semi-auto calibration
776	Check the span gas concentration. Span gas: %{0} % Zero gas: %{1} %
777	Calibration time: %{3} min %{2} s Purge time: %{1} min %{0} s
778	Do you want to execute semi-auto calibration?
779	Calibration is started
780	Do you want to abort calibation:
781	WARN-If you press OK, calibration will be aborted
782	Aborting calibration
783	Do you want to cancel purge time:
784	WARN-If you press OK, purge time will be canceled
785	Canceling purge time
786	Device is %{0} Calibration is not executing!
787	WARN-Device is not selected to start blow back
788	Blow back can't execute!
789	WARN-Device's DO are not selected Blow Back
790	Blow back time: %{3} min %{2} s Purge time: %{1} min %{0} s
791	Do you want to execute blow back?
792	WARN-Blow back can't execute!
793	Blow back is started
794	Device is %{0} Blow back can't execute!
795	Do you want to abort blow back:
796	WARN-If you press OK, blow back will be aborted
797	Aborting blow back
798	Device is %{0} Blow back is not executing!
799	Checking maximum oxygen conc. and occured date
800	Max. %{0}: %{1} %{2} Occurred at: %{3}/%{4}/%{5} %{6}:%{7}
801	Max. %{0}: %{1} %{2} Occurred at: %{3}/%{4}/0%[1d]{5} %{6}:%{7}
802	Max. %{0}: %{1} %{2} Occurred at: %{3}/%{4}/%{5} %{6}:0%[1d]{7}
803	Max. %{0}: %{1} %{2} Occurred at: %{3}/%{4}/0%[1d]{5} %{6}:0%[1d]{7}
804	Checking minimum oxygen conc. and occured date
805	Min. %{0}: %{1} %{2} Occurred at: %{3}/%{4}/%{5} %{6}:%{7}
806	Min. %{0}: %{1} %{2} Occurred at: %{3}/%{4}/0%[1d]{5} %{6}:%{7}
807	Min. %{0}: %{1} %{2} Occurred at: %{3}/%{4}/%{5} %{6}:0%[1d]{7}
808	Min. %{0}: %{1} %{2} Occurred at: %{3}/%{4}/0%[1d]{5} %{6}:0%[1d]{7}
809	Checking maximum humidity conc. and occured date
810	Checking minimum humidity conc. and occured date
811	Checking maximum mixing ratio and occured date
812	Checking minimum mixing ratio and occured date
813	Record %{0}: Span: %{1} % Zero: %{2} % Date: %{3}/%{4}/%{5} %{6}:%{7}
814	Record %{0}: Span: %{1} % Zero: %{2} % Date: %{3}/%{4}/0%[1d]{5} %{6}:%{7}
815	Record %{0}: Span: %{1} % Zero: %{2} % Date: %{3}/%{4}/%{5} %{6}:0%[1d]{7}
816	Record %{0}: Span: %{1} % Zero: %{2} % Date: %{3}/%{4}/0%[1d]{5} %{6}:0%[1d]{7}
817	Present data & time: %{0} %{1}:%{2}
818	Present data & time: %{0} %{1}:0%[1d]{2}
819	Present data & time: %{0} %{1}:%{2}
820	Present data & time: %{0} %{1}:0%[1d]{2}
821	Do you want to set new value?
822	Please set date:
823	Please set hour:
824	Please set minute:
825	New date & time: %{0} %{1}:%{2} Pressing 'OK' will send them.
826	New date & time: %{0} %{1}:0%[1d]{2} Pressing 'OK' will send them.
827	Date & time change has been completed.
828	Purge time: %{1} min %{0} s
829	Please set min:
830	Please set sec:
831	Purge time: %{1} min %{0} s Pressing 'OK' will send them.
832	Calibration purge time change has been completed.
833	Calib. time: %{1} min %{0} s
834	Calib. time: %{1} min %{0} s Pressing 'OK' will send them.
835	Calibration time change has been completed.
836	Calib. timing: Interval: %{1} d %{0} h Start date: %{2} %{3}:%{4}
837	Calib. timing: Interval: %{1} d %{0} h Start date: %{2} %{3}:0%[1d]{4}
838	Please set interval day:
839	Please set interval hour:
840	Please set start date:
841	Please set start hour:
842	Please set start minute:
843	New interval: %{1} d %{0} h New start date: %{2} %{3}:%{4} Pressing 'OK' will send them.
844	New interval: %{1} d %{0} h New start date: %{2} %{3}:0%[1d]{4} Pressing 'OK' will send them.
845	Interval and start date change have been completed.
846	Blow back purge time change has been completed.
847	Blow time: %{1} min %{0} s
848	Blow time: %{1} min %{0} s Pressing 'OK' will send them.
849	Blow back time change has been completed.
850	Blow back timing: Interval: %{1} d %{0} h Start date: %{2} %{3}:%{4}
851	Blow back timing: Interval: %{1} d %{0} h Start date: %{2} %{3}:0%[1d]{4}
852	Enter current password to enable to write for 10 minutes:
853	Released the write protection for 10 minutes.
854	If you want to release completely, you have to change password to all of spaces.
855	Enter new password to change state of write protect:
856	Re-enter new password within 30 seconds:
857	Aborting method due to last error
858	Changed to new password.
859	It changed the state of protection related password.
引用ID	字符串