Device dictionary

Loading…

Reference ID	String
0	YOKOGAWA
1	TDLS8000
2	Device Configuration Locked
3	Device is in write-protect or is locked.
4	Status group 1
5	Transmission Low (AL-01)
6	Transmission value is below its threshold.(AL-01) [Remedy]:Confirm analyzer alignment. Check nothing is blocking the laser light. Clean process windows. Refer to Instruction Manual for details.
7	Pressure Low (AL-02)
8	Pressure value is below its threshold.(AL-02) [Remedy]:Check process gas pressure value. Check pressure transducer signal is correct. Check AI range settings. Refer to Instruction Manual for details.
9	Pressure High (AL-03)
10	Pressure value is above its threshold.(AL-03) [Remedy]:Check process gas pressure value. Check pressure transducer signal is correct. Check AI range settings. Refer to Instruction Manual for details.
11	Temperature Low (AL-04)
12	Process temperature is below its threshold.(AL-04) [Remedy]:Check process gas temperature value. Check temperature transducer signal is correct. Check AI range settings. Refer to Instruction Manual for details.
13	Temperature High (AL-05)
14	Process temperature is above its threshold.(AL-05) [Remedy]:Check process gas temperature value. Check temperature transducer signal is correct. Check AI range settings. Refer to Instruction Manual for details.
15	Conc Gas1 Low (AL-06)
16	Concentration gas1 value is below its threshold.(AL-06) [Remedy]:Check process gas concentration value and its threshold of low alarm. Refer to Instruction Manual for details.
17	Conc Gas1 High (AL-07)
18	Concentration gas1 value is above its threshold.(AL-07) [Remedy]:Check process gas concentration value and its threshold of high alarm. Refer to Instruction Manual for details.
19	Conc Gas2 Low (AL-08)
20	Concentration gas2 value is below its threshold.(AL-08) [Remedy]:Check process gas2 concentration value and its threshold of low alarm. Refer to Instruction Manual for details.
21	Status group 2
22	Conc Gas2 High (AL-09)
23	Concentration gas2 value is above its threshold.(AL-09) [Remedy]:Check process gas2 concentration value and its threshold of high alarm. Refer to Instruction Manual for details.
24	LU Temp Low (AL-10)
25	Laser unit temperature is below its threshold.(AL-10) [Remedy]:Check excessive cold output from adjacent process and/or ambient condition around the laser unit. Contact the nearest office or service center.
26	LU Temp High (AL-11)
27	Laser unit temperature is above its threshold.(AL-11) [Remedy]:Check excessive hot output from adjacent process and/or ambient condition around the laser unit. Contact the nearest office or service center.
28	SCU Temp Low (AL-12)
29	Sensor control unit temperature is below its threshold.(AL-12) [Remedy]:Check excessive cold output from adjacent process and/or ambient condition around the sensor control unit. Contact the nearest office or service center.
30	SCU Temp High (AL-13)
31	Sensor control unit temperature is above its threshold.(AL-13) [Remedy]:Check excessive hot output from adjacent process and/or ambient condition around the sensor control unit. Contact the nearest office or service center.
32	Validation Required (AL-14)
33	Validation is required to verify measurement accuracy.(AL-14) [Remedy]:Perform validation, or clear validation alarm if you are sure there is no problem.
34	Validation Error (AL-15)
35	Validation has failed.(AL-15) [Remedy]:Check validation gas and validation settings. Refer to Instruction Manual for details.
36	Zero Cal Error (AL-16)
37	Zero calibration has failed.(AL-16) [Remedy]:Check calibration gas and zero calibration settings. Refer to Instruction Manual for details.
38	Status group 3
39	Span Cal Error (AL-17)
40	Span calibration has failed.(AL-17) [Remedy]:Check calibration gas and span calibration settings. Refer to Instruction Manual for details.
41	Non Process Alarm (AL-19)
42	Non-process reference peak height is below its threshold.(AL-19) [Remedy]:Check purge gas flow. Check purge gas concentration value. Contact the nearest office or service center.
43	AI-1 (Pres) Low (AL-20)
44	AI-1 (pressure input) current is below its threshold.(AL-20) [Remedy]:Check process gas pressure value. Check pressure transducer signal is correct. Check AI range settings. Refer to Instruction Manual for details.
45	AI-1 (Pres) High (AL-21)
46	AI-1 (pressure input) current is above its threshold.(AL-21) [Remedy]:Check process gas pressure value. Check pressure transducer signal is correct. Check AI range settings. Refer to Instruction Manual for details.
47	AI-2 (Temp) Low (AL-22)
48	AI-2 (temperature input) current is below its threshold.(AL-22) [Remedy]:Check process gas temperature value. Check temperature transducer signal is correct. Check AI range settings. Refer to Instruction Manual for details.
49	AI-2 (Temp) High (AL-23)
50	AI-2 (temperature input) current is above its threshold.(AL-23) [Remedy]:Check process gas temperature value. Check temperature transducer signal is correct. Check AI range settings. Refer to Instruction Manual for details.
51	External Alarm (AL-24)
52	DI which is assigned to external alarm is contact.(AL-24) [Remedy]:Check external alarm status.
53	Status group 4
54	Clock Adj Required (AL-25)
55	Clock adjustment is required.(AL-25) [Remedy]:Set Real Time Clock date/time.
56	Setting File Error (AL-26)
57	Setting file has been recovered by backup data since it was corrupted.(AL-26) [Remedy]:Configure again and then reboot the device.
58	Calib File Error (AL-27)
59	Calibration data file has been recovered by backup data since it was corrupted.(AL-27) [Remedy]:Calibrate again and then reboot the device.
60	Status group 5
61	Status group 6
62	Laser Md Temp Low (AL-45)
63	Laser module temperature is below its threshold.(AL-45) [Remedy]:Check excessive cold output from adjacent process and/or ambient condition around the laser unit. Contact the nearest office or service center.
64	Laser Md Temp High (AL-46)
65	Laser module temperature is above its threshold.(AL-46) [Remedy]:Check excessive hot output from adjacent process and/or ambient condition around the laser unit. Contact the nearest office or service center.
66	Laser Temp Low (AL-47)
67	Laser temperature is below its threshold.(AL-47) [Remedy]:Contact the nearest office or service center.
68	Laser Temp High (AL-48)
69	Laser temperature is above its threshold.(AL-48) [Remedy]:Contact the nearest office or service center.
70	Status group 7
71	Detect Signal High (AL-49)
72	Detector signal level is above its threshold.(AL-49) [Remedy]:Contact the nearest office or service center.
73	Peak Center OOR (AL-50)
74	Peak center is out of range.(AL-50) [Remedy]:Contact the nearest office or service center.
75	Ref Peak Height Low (AL-51)
76	Reference peak height is below its threshold.(AL-51) [Remedy]:Contact the nearest office or service center.
77	Absorption High (AL-52)
78	Absorption spectrum level is above its threshold.(AL-52) [Remedy]:Contact the nearest office or service center.
79	Transmission Lost (AL-53)
80	Transmission is extraordinary low.(AL-53) [Remedy]:Confirm analyzer alignment. Check nothing is blocking the laser light. Clean process windows. Refer to Instruction Manual for details.
81	Ref Trans Low (AL-54)
82	Reference transmission is below its threshold.(AL-54) [Remedy]:Contact the nearest office or service center.
83	R Peak Height High (AL-55)
84	Reference cell peak height is above its threshold.(AL-55) [Remedy]:Contact the nearest office or service center.
85	Outlier Reject Lmt (AL-56)
86	Data acquisition has failed by excessive rejections.(AL-56) [Remedy]:Contact the nearest office or service center.
87	Status group 8
88	Laser Unit Fail (AL-57)
89	Laser unit failure occurs.(AL-57) [Remedy]:Contact the nearest office or service center.
90	Inter Comm Fail (AL-58)
91	Internal communication error occurs.(AL-58) [Remedy]:Contact the nearest office or service center.
92	Laser Module Error (AL-59)
93	Laser module error occurs.(AL-59) [Remedy]:Contact the nearest office or service center.
94	File Access Error (AL-60)
95	File access error occurs.(AL-60) [Remedy]:Contact the nearest office or service center.
96	EEPROM Error (AL-61)
97	EEPROM error occurs.(AL-61) [Remedy]:Contact the nearest office or service center.
98	LU Connect Error (AL-62)
99	Laser unit connection error occurs.(AL-62) [Remedy]:Check cable connections to the laser unit. Contact the nearest office or service center.
100	FPGA Failure (AL-63)
101	FPGA failure occurs.(AL-63) [Remedy]:Contact the nearest office or service center.
102	Program Error (AL-64)
103	CPU program error occurs.(AL-64) [Remedy]:Contact the nearest office or service center.
104	Status group 9
105	Warm-up
106	Maintenance mode
107	Status group 10
108	Zero Cal
109	Span Cal
110	Online Val
111	Offline Val
112	AI-1 (Pres) Cal
113	AI-2 (Temp) Cal
114	Analog outputs
115	QV
116	PV AO
117	.2f
118	.3f
119	.1f
120	.4f
121	.5f
122	.6f
123	.7f
124	f
125	PV AO Alrm typ
126	Preset hold
127	SV AO
128	SV AO Alrm typ
129	SV AO Channel flags
130	SV AO added damp
131	SV AO display unit
132	SV % rnge
133	SV transfer function
134	SV URV
135	SV LRV
136	Concentration 1
137	.0f
138	Conc 1 unit
139	mg/m3
140	milligrams per cubic meter
141	mg/Nm3
142	milligrams per standard cubic meter
143	Conc 1 Data Quality
144	Conc 1 Limit Status
145	Conc 1 Classification
146	Conc 1 Family status
147	Not supported
148	Conc 1 Family
149	Conc 1 transfer func
150	Concentration 2
151	Conc 2 unit
152	Conc 2 Data Quality
153	Conc 2 Limit Status
154	Conc 2 Classification
155	Conc 2 Family status
156	Conc 2 Family
157	Conc 2 transfer func
158	Transmission
159	Trans unit
160	Trans Data Quality
161	Trans Limit Status
162	Trans Classification
163	Trans Family status
164	Trans Family
165	Trans transfer func
166	Temperature
167	Temp unit
168	Temp Data Quality
169	Temp Limit Status
170	Temp Classification
171	Temp Family status
172	Temp Family
173	Temp transfer func
174	Pressure
175	Pres unit
176	Pres Data Quality
177	Pres Limit Status
178	Pres Classification
179	Pres Family status
180	Pres Family
181	Pres transfer func
182	Concentration Gas1
183	Concentration Gas2
184	OPL
185	Pres mode
186	Fixed
187	Active input
188	Pres fix mode val
189	Pressure value when fixed mode
190	Pres active type
191	Pressure source of active input mode
192	AI-1
193	Field communication
194	Pres val at 4mA
195	Pressure value when AI-1 is 4mA
196	Pres val at 20mA
197	Pressure value when AI-1 is 20mA
198	Pres backup mode
199	Backup value
200	Hold
201	Pres backup set val
202	Pressure backup preset value when its active input is out of range
203	Temp mode
204	Active ambient
205	Active peak
206	Temp fix mode val
207	Temperature value when fixed mode
208	Temp active type
209	Temperature source of active input mode
210	AI-2
211	Temp val at 4mA
212	Temperature value when AI-2 is 4mA
213	Temp val at 20mA
214	Temperature value when AI-2 is 20mA
215	Temp backup mode
216	Temp backup set val
217	Temperature backup preset value when its active input is out of range
218	Temp act amb ofst
219	Active ambient offset value
220	Temp act peak enable
221	No-prcs OPL
222	No-prcs pres
223	No-prcs temp mode
224	No-prcs temp fix val
225	No-prcs act amb coef
226	Temperature compensation coefficient of non-process active ambient mode
227	No-prcs conc 1
228	No-prcs conc 2
229	Gas 2 enable switch
230	Conc 1 gas type
231	Conc 2 gas type
232	Conc 1 decimal point
233	Conc 2 decimal point
234	OPL unit
235	Warn select group 1
236	Warn select group 2
237	Warn select group 3
238	Warn select group 4
239	Warn select group 5
240	Warn select group 6
241	Warn select group 7
242	Warn select group 8
243	Trans low lmt
244	Pres low lmt
245	Pres high lmt
246	Temp low lmt
247	Temp high lmt
248	Conc 1 low lmt
249	Conc 2 low lmt
250	Conc 1 high lmt
251	Conc 2 high lmt
252	AO1 warn hld mode
253	Non-hold
254	AO2 warn hld mode
255	AO1 warn hld level
256	AO-1 preset hold level when warning mode
257	AO2 warn hld level
258	AO-2 preset hold level when warning mode
259	AO1 warn hld delay
260	AO-1 preset hold delay number when warning mode
261	update
262	AO2 warn hld delay
263	AO-2 preset hold delay number when warning mode
264	AO1 fault hld mode
265	AO2 fault hld mode
266	AO1 fault hld level
267	AO-1 preset hold level when fault mode
268	AO2 fault hld level
269	AO-2 preset hold level when fault mode
270	AO1 fault hld delay
271	AO-1 preset hold delay number when fault mode
272	AO2 fault hld delay
273	AO-2 preset hold delay number when fault mode
274	AO1 calval hld mode
275	AO2 calval hld mode
276	AO1 calval hld level
277	AO-1 preset hold level when cal/val mode
278	AO2 calval hld level
279	AO-2 preset hold level when cal/val mode
280	AO1 maint hld mode
281	AO2 maint hld mode
282	AO1 maint hld level
283	AO-1 preset hold level when maintenance mode
284	AO2 maint hld level
285	AO-2 preset hold level when maintenance mode
286	AO1 w-up hld mode
287	AO2 w-up hld mode
288	AO1 w-up hld level
289	AO-1 preset hold level when warm-up mode
290	AO2 w-up hld level
291	AO-2 preset hold level when warm-up mode
292	DO-1 output delay
293	DO-2 output delay
294	None
295	DO-1 output item
296	Warning
297	Cal/Val mode
298	Warm-up mode
299	DO-2 output item
300	Fault
301	DI-1 filter time
302	0.1 s
303	0.2 s
304	0.5 s
305	1.0 s
306	2.0 s
307	DI-2 filter time
308	DI-1 mode
309	Disable
310	External Alarm
311	Zero Calibration
312	Span Calibration
313	Zero + Span Calibration
314	Offline Validation 1
315	Offline Validation 2
316	Offline Validation 1 + 2
317	Online Validation 1
318	Online Validation 2
319	Shutdown
320	Valve Stream 1
321	Valve Stream 2
322	Valve Stream 3
323	DI-2 mode
324	Valve usage
325	Cal/val
326	2 stream switch & cal/val
327	3 stream switch
328	Initial stream
329	Stream setting at device startup
330	Stream 1
331	Stream 2
332	Stream 3
333	Current stream
334	Stream setting under manual control
335	Switch stream1 to
336	Switch stream2 to
337	Switch stream3 to
338	Stream1 duration
339	Stream2 duration
340	Stream3 duration
341	Zero cal vlv stream
342	Span cal vlv stream
343	Offval1 vlv stream
344	Offval2 vlv stream
345	Onval1 vlv stream
346	Onval2 vlv stream
347	Tst auto release time
348	All test outputs by loop check will be released after this time.
349	10 min
350	30 min
351	60 min
352	3 hour
353	6 hour
354	12 hour
355	AO-1 loop chk mode
356	AO-2 loop chk mode
357	AO-1 chk output
358	AO-2 chk output
359	DO-1 loop chk mode
360	DO-2 (Flt) loop chk mode
361	DO-1 chk output
362	DO-2 (Flt) chk output
363	Vlv-1 loop chk mode
364	Vlv-2 loop chk mode
365	Vlv-1 chk output
366	Vlv-2 chk output
367	Laser module SN
368	Averaging number
369	Averaging time
370	IP address
371	Subnet mask
372	Default gateway
373	Z-cal day cycle
374	Execution day cycle after initial execution of zero calibration. 0 means OFF.
375	Z-cal init date
376	Initial execution date of zero calibration by yyyy/mm/dd format
377	Z-cal init time
378	Initial execution time of zero calibration by hh:mm:ss format
379	Z-cal gas purg time
380	Purging time of calibration gas at zero calibration
381	Z-cal proc purg time
382	Purging time of process gas at zero calibration
383	Z-cal auto vlv man
384	Auto valve control during manual zero calibration
385	Z-cal time initiate
386	Zero offset 1
387	Zero offset 2
388	S-cal pres fix val
389	S-cal temp fix val
390	S-cal OPL fix val
391	S-cal gas conc
392	S-cal gas type
393	Gas 1
394	Gas 2
395	S-cal day cycle
396	Execution day cycle after initial execution of span calibration. 0 means OFF.
397	S-cal init date
398	Initial execution date of span calibration by yyyy/mm/dd format
399	S-cal init time
400	Initial execution time of span calibration by hh:mm:ss format
401	S-cal gas purg time
402	Purging time of calibration gas at span calibration
403	S-cal proc purg time
404	Purging time of process gas at span calibration
405	S-cal auto vlv man
406	Auto valve control during manual span calibration
407	S-cal pres mode
408	Process parameter
409	Fixed value
410	S-cal temp mode
411	S-cal OPL mode
412	S-cal time initiate
413	Z+S cal time initiate
414	Z+S cal day cycle
415	Execution day cycle after initial execution of zero+span calibration. 0 means OFF.
416	Z+S cal init date
417	Initial execution date of zero+span calibration by yyyy/mm/dd format
418	Z+S cal init time
419	Initial execution time of zero+span calibration by hh:mm:ss format
420	Offval1 pres mode
421	Offval2 pres mode
422	Offval1 temp mode
423	Offval2 temp mode
424	Offval1 OPL mode
425	Offval2 OPL mode
426	Offval1 time initiate
427	Offval2 time initiate
428	Offval1 pres fix val
429	Offval2 pres fix val
430	Offval1 temp fix val
431	Offval2 temp fix val
432	Offval1 OPL fix val
433	Offval2 OPL fix val
434	Offval1 gas conc
435	Offval2 gas conc
436	Offval1 gas type
437	Offval2 gas type
438	Offval1 day cycle
439	Execution day cycle after initial execution of offline validation 1. 0 means OFF.
440	Offval2 day cycle
441	Execution day cycle after initial execution of offline validation 2. 0 means OFF.
442	Offval1 init date
443	Initial execution date of offline validation 1 by yyyy/mm/dd format
444	Offval1 init time
445	Initial execution time of offline validation 1 by hh:mm:ss format
446	Offval2 init date
447	Initial execution date of offline validation 2 by yyyy/mm/dd format
448	Offval2 init time
449	Initial execution time of offline validation 2 by hh:mm:ss format
450	Offval1 gas purg time
451	Purging time of validation gas at offline validation 1
452	Offval2 gas purg time
453	Purging time of validation gas at offline validation 2
454	Offval1 prc purg time
455	Purging time of process gas at offline validation 1
456	Offval2 prc purg time
457	Purging time of process gas at offline validation 2
458	Offval1 auto vlv man
459	Auto valve control during manual offline validation 1
460	Offval2 auto vlv man
461	Auto valve control during manual offline validation 2
462	Offval1+2 time init
463	Offval1+2 day cycle
464	Execution day cycle after initial execution of offline validation 1+2. 0 means OFF.
465	Offval1+2 init date
466	Initial execution date of offline validation 1+2 by yyyy/mm/dd format
467	Offval1+2 init time
468	Initial execution time of offline validation 1+2 by hh:mm:ss format
469	Onval1 temp mode
470	Onval2 temp mode
471	Onval1 act amb ofst
472	Onval2 act amb ofst
473	Onval1 pres fix val
474	Onval2 pres fix val
475	Onval1 temp fix val
476	Onval2 temp fix val
477	Onval1 OPL fix val
478	Onval2 OPL fix val
479	Onval1 gas conc
480	Onval2 gas conc
481	Onval1 gas type
482	Onval2 gas type
483	Onval1 time initiate
484	Onval2 time initiate
485	Onval1 day cycle
486	Execution day cycle after initial execution of online validation 1. 0 means OFF.
487	Onval2 day cycle
488	Execution day cycle after initial execution of online validation 2. 0 means OFF.
489	Onval1 init date
490	Initial execution date of online validation 1 by yyyy/mm/dd format
491	Onval1 init time
492	Initial execution time of online validation 1 by hh:mm:ss format
493	Onval2 init date
494	Initial execution date of online validation 2 by yyyy/mm/dd format
495	Onval2 init time
496	Initial execution time of online validation 2 by hh:mm:ss format
497	Onval1 auto vlv man
498	Auto valve control during manual online validation 1
499	Onval2 auto vlv man
500	Auto valve control during manual online validation 2
501	Onval1 gas purg time
502	Purging time of validation gas at online validation 1
503	Onval2 gas purg time
504	Purging time of validation gas at online validation 2
505	Onval1 nml purg time
506	Purging time of normal gas at online validation 1
507	Onval2 nml purg time
508	Purging time of normal gas at online validation 2
509	Onval1 read mode
510	Concentration reading mode of online validation 1
511	Process + Validation
512	Validation only
513	Onval2 read mode
514	Concentration reading mode of online validation 2
515	Onval1 output factor
516	Concentration output factor of online validation 1
517	Onval2 output factor
518	Concentration output factor of online validation 2
519	LCD spect disp mode
520	Hide
521	During alarm status
522	Periodically
523	Each measurement spectrum
524	Each reference spectrum
525	LCD backlight bright
526	LCD contrast
527	LED brightness
528	Analyzer SN
529	Model name
530	Software ver
531	Cal/Val by HART
532	SI unit control
533	Stream 1 vlv pattern
534	V1=Off V2=Off
535	V1=On V2=Off
536	V1=Off V2=On
537	V1=On V2=On
538	Stream 2 vlv pattern
539	Stream 3 vlv pattern
540	Z-cal hour cycle
541	Execution hour cycle after initial execution of zero calibration. 0 means OFF.
542	S-cal hour cycle
543	Execution hour cycle after initial execution of span calibration. 0 means OFF.
544	Z+S cal hour cycle
545	Execution hour cycle after initial execution of zero+span calibration. 0 means OFF.
546	Offval1 hour cycle
547	Execution hour cycle after initial execution of offline validation 1. 0 means OFF.
548	Offval2 hour cycle
549	Execution hour cycle after initial execution of offline validation 2. 0 means OFF.
550	Offval1+2 hour cycle
551	Execution hour cycle after initial execution of offline validation 1+2. 0 means OFF.
552	Onval1 hour cycle
553	Execution hour cycle after initial execution of online validation 1. 0 means OFF.
554	Onval2 hour cycle
555	Execution hour cycle after initial execution of online validation 2. 0 means OFF.
556	Analysis period
557	New Password
558	enable_write_10min
559	Software seal
560	Break
561	Keep
562	hart_rtc_date
563	hart_rtc_time
564	Memo 1
565	Memo 2
566	Memo 3
567	Trim Desc
568	Trim Loc
569	Trim Who
570	Trim Date
571	AI-1 (pres)
572	AI-2 (temp)
573	DI-1
574	Open
575	Closed
576	DI-2
577	DO-1
578	DO-2 (Fault)
579	Valve-1
580	Valve-2
581	Conc 1 STDEV
582	Conc 2 STDEV
583	1
584	2
585	Normal
586	Warming up
587	Cal/Val
588	Maintenance
589	Power On
590	Restarted by WDT
591	Restarted by Power Failure
592	Laser Module Replaced
593	Bootloader Updated
594	Firmware Updated
595	FPGA Updated
596	Config File Updated
597	Backuped Config Loaded
598	Default Config Loaded
599	Default Firmware Loaded
600	Default HART config loaded
601	Reset by External Operation
602	RTC was Adjusted
603	Auto Zero Cal was Skipped
604	Auto Span Cal was Skipped
605	Auto Online Cal was Skipped
606	Auto Validation was Skipped
607	HMI Connected
608	HMI Disconnected
609	HMI Disconnected(recv)
610	HMI Disconnected(send)
611	History File was Corrupted
612	ON
613	OFF
614	Man Zero Cal
615	Auto Zero Cal
616	Man Span Cal
617	Auto Span Cal
618	Man Online Span Cal
619	Auto Online Span Cal
620	Man Offline Val 1
621	Man Offline Val 2
622	Auto Offline Val 1
623	Auto Offline Val 2
624	Man Online Val 1
625	Man Online Val 2
626	Auto Online Val 1
627	Auto Online Val 2
628	Transmission Ref
629	Zero Offset 1
630	Zero Offset 2
631	Zero Cal restored by factory data
632	Zero Cal restored by previous data
633	Span Cal restored by factory data
634	Span Cal restored by previous data
635	DAQ Offset Cal
636	Don't care
637	Gas1
638	Gas2
639	Setting data
640	AI/AO cal data
641	Calibration data
642	User info
643	OK
644	NG
645	Pass
646	Fail
647	The validation is PASSED.
648	WARN-The validation is FAILED.
649	Dev cfg locked mask
650	When this mask is ON, the HART "Device Configuration Locked" bit is always OFF even if device is in write protect mode.
651	Squawk Once
652	enum32_dummy_1
653	enum32_dummy_2
654	reserve_int32_1
655	reserve_int32_2
656	reserve_int32_3
657	reserve_int32_4
658	reserve_float_1
659	reserve_float_2
660	reserve_float_3
661	reserve_float_4
662	reserve_uint8_1
663	reserve_uint8_2
664	reserve_uint8_3
665	reserve_uint8_4
666	reserve_bit_enum8_1
667	RESERVED
668	reserve_bit_enum8_2
669	reserve_bit_enum8_3
670	reserve_bit_enum8_4
671	reserve_enum8_1
672	reserve_enum8_2
673	reserve_enum8_3
674	reserve_enum8_4
675	reserve_enum32_1
676	reserve_enum32_2
677	reserve_enum32_3
678	reserve_enum32_4
679	reserve_ascii8_1
680	reserve_ascii8_2
681	reserve_ascii8_3
682	reserve_ascii8_4
683	reserve_ascii16_1
684	reserve_ascii16_2
685	reserve_ascii16_3
686	reserve_ascii16_4
687	reserve_ascii32_1
688	reserve_ascii32_2
689	reserve_ascii32_3
690	reserve_ascii32_4
691	reserve_date10_1
692	reserve_time8_1
693	reserve_date10_2
694	reserve_time8_2
695	reserve_date10_3
696	reserve_time8_3
697	reserve_date10_4
698	reserve_time8_4
699	reserve_bit_enum16_1
700	reserve_bit_enum16_2
701	reserve_bit_enum16_3
702	reserve_bit_enum16_4
703	reserve_uint16_1
704	reserve_uint16_2
705	reserve_uint16_3
706	reserve_uint16_4
707	reserve_uint32_1
708	reserve_uint32_2
709	reserve_uint32_3
710	reserve_uint32_4
711	Device variables
712	Dynamic variables
713	Dynamic var status
714	Dynamic var assign
715	Diagnosis/Service
716	Test/Status
717	View status
718	Status mask
719	Logbook
720	Loop check
721	Digital output
722	Valve
723	Trim analog channel
724	Trim info
725	Calibration
726	Manual
727	Semi-auto
728	Restore
729	Validation
730	Transmission adjust
731	PV range
732	SV range
733	Assign TV & QV
734	System
735	Alarm
736	Warning group 1
737	Warning group 2
738	I/O condition
739	Analog output
740	AO-1
741	Warning hold
742	Fault hold
743	Cal/Val hold
744	Maintenance hold
745	Warm-up hold
746	AO-2
747	Analog input
748	AI-1 (Pressure)
749	AI-2 (Temperature)
750	DO-1 (DO)
751	Digital input
752	Valve control
753	Stream time switch
754	Analysis
755	Process param
756	Non process param
757	No-prcs temp
758	No-prcs conc
759	Unit
760	Averaging
761	Zero offset
762	Zero calibration
763	Auto time
764	Span calibration
765	Parameter
766	Zero+Span calibration
767	Offline validation 1
768	Offline validation 2
769	Offline validation 1+2
770	Online validation 1
771	Conc reading mode
772	Online validation 2
773	Date/time
774	Communication
775	TCP/IP
776	Local display
777	SCU LCD display
778	LU LED display
779	Field device info
780	Write protect menu
781	Memo
782	Process info
783	I/O info
784	I/O assignment
785	System info
786	Factory info
787	Version #'s
788	Additional info
789	Offline
790	Upload variables
791	Not write protect mode
792	The First Password Accepted
793	Enable write 10min
794	New password
795	Aborting
796	Exiting
797	Trim AI-1 (Pres)
798	Trim AI-2 (Temp)
799	Manual zero cal
800	Manual span cal
801	Semi-auto zero cal
802	Semi-auto span cal
803	Abort calibration
804	Manual offline val 1
805	Manual offline val 2
806	Semi-auto offline val 1
807	Semi-auto offline val 2
808	Semi-auto offline val 1+2
809	Manual online val 1
810	Manual online val 2
811	Semi-auto online val 1
812	Semi-auto online val 2
813	Abort validation
814	Initialize config
815	Set valve usage
816	Stream settings of each cal/val cannot conflict with valve usage. These are initialized automatically when changing valve usage.
817	Present date/time
818	Set date/time
819	Set s-cal gas type
820	Set offval1 gas type
821	Set offval2 gas type
822	Set onval1 gas type
823	Set onval2 gas type
824	Read alarm/message record
825	Read cal/val record
826	Restore zero cal data
827	Restore span cal data
828	Clear cal alarms
829	Clear val alarms
830	Set DI-1 mode
831	Cal/val whose valve stream is conflicted with Valve Usage cannot be assigned to DI mode.
832	Set DI-2 mode
833	Reset cfg chng flag
834	Trim AO-1 (PV)
835	Trim AO-2 (SV)
836	Set IP settings
837	Clear latched alarms
838	Reset laser temperature
839	PV Analog Channel Saturated
840	PV Analog Channel Fixed
841	Wireless
842	WirelessHART Device
843	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
844	Primary
845	Primary Analog Channel
846	Secondary
847	Secondary Analog Channel
848	Tertiary
849	Tertiary Analog Channel
850	Quaternary
851	Quaternary Analog Channel
852	Quinary
853	Quinary Analog Channel
854	Critical Power Failure
855	Trim not supported
856	Analog Input Channel
857	Analog Output Channel
858	Secondary Analog Channel Saturated
859	Tertiary Analog Channel Saturated
860	Quaternary Analog Channel Saturated
861	Quinary Analog Channel Saturated
862	Secondary Analog Channel Fixed
863	Tertiary Analog Channel Fixed
864	Quaternary Analog Channel Fixed
865	Quinary Analog Channel Fixed
866	Simulation active
867	The device is in simulation mode and the level output is not representative of the process.
868	Non-Volatile memory failure
869	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
870	Volatile memory error
871	The RAM memory check is invalid or maybe corrupt
872	Watchdog reset executed
873	A watchdog reset has been performed
874	Voltage conditions out of range
875	A voltage condition is outside its allowable range
876	Environmental conditions out of range
877	An internal or environmental condition is beyond acceptable limits.
878	Electronic failure
879	A hardware problem not related to the sensor has been detected.
880	Subdevice list changed
881	Duplicate master detected
882	Capacity Denied
883	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
884	Bandwidth allocation pending
885	Block transfer pending
886	Battery life
887	Percent range
888	Loop current
889	Primary variable
890	Secondary variable
891	Tertiary variable
892	Quaternary variable
893	Process automation device
894	Discrete device
895	Hybrid:Process automation+discrete
896	I/O System
897	WirelessHART Process automation device
898	WirelessHART Discrete device
899	WirelessHART Process automation+discrete
900	WirelessHART Gateway
901	WirelessHART Access point
902	WirelessHART Process adapter
903	WirelessHART Discrete adapter
904	WirelessHART enabled handheld/portable maintenance tool
905	Device Profile
906
907	No restrictions
908	SI Only
909	Restricted to SI Unit codes only
910	Device Diagnostic Status 0
911	Device Diagnostic Status 1
912	I/O and Subdevice Status
913	WirelessHART Status
914	8u
915	Dynamic Variables Returned for Device Variables
916	Command Response Truncated
917	Configuration Change Counter Mismatch
918	Status bytes mismatch
919	Device Variable
920	Analog Channel Number
921	Analog Channel Number- Index into an array of Analog Channels.
922	8.3f
923	Output Status
924	Output Status Byte
925	Uninitialized
926	Normal - one sensor
927	Normal - two sensors
928	Normal - three sensors
929	Shorted
930	Shorted- shorted field wiring.
931	Limited high
932	Limited high- block can not respond to upward movement of value.
933	Open- open field wiring.
934	Limited low
935	Limited low- block can not respond to upward movement of target.
936	Initialization done
937	Initialization done- block initialization is complete.
938	Not selected
939	Not selected- target value provided by block was not selected.
940	No path
941	No path- there is no path to the process.
942	Fail- hardware failure.
943	Bad
944	Bad- block is out of service or has bad input.
945	Not from process
946	Not from process- value is not directly affected by any process information.
947	Local override
948	Local override- block has LO mode.
949	Not Cascade Mode
950	Not RCas Mode
951	Not ROut Mode
952	No communication
953	No communication- (NO_COM).
954	uint16_var_blk_char
955	uint32_var_blk_char
956	uint8_var_blk_char
957	int8_var_blk_char
958	new itest redef1 label
Reference ID	String