HART设备字典

Loading…

引用ID	字符串
0	SC450
1	Measurement unstable
2	TC error (SC2)
3	TC error (SC1)
4	Temperature too low
5	Temperature too high
6	Conductivity too low
7	Conductivity too high
8	Error in conc. table
9	USP limit exceeded
10	USP margin exceeded
11	Polarization detected
12	Error in 1st matrix
13	Error in 2nd matrix
14	Logbook (almost) full
15	Checksum error
16	Initialization error
17	Calibration scheduled
18	mA burn low
19	mA burn high
20	Simulated mA value
21	Expiry time exceeded
22	mA configuration error
23	Error in mA table
24
25	Simulated contact
26	Contact configuration error
27	.3f
28	8.3f
29	7d
30	st_rev
31	Target Mode
32	Set mode to OOS to be able to read & write parameters. If mode is set to AUTO parameters can be read only
33	OOS
34	Auto
35	Actual Mode
36	Meas
37	The type of measurement represented by primary value.
38	Conductivity
39	Resisitivity
40	PV.status
41	The status of the primary value.
42	PV
43	Primary value.
44	.1f
45	.0f
46	.2f
47	.4f
48	.3g
49	PV.range_eu_100
50	PV.range_eu_0
51	PV.range_units
52	°C
53	°F
54	p/m
55	S
56	mS
57	O.m
58	O.cm
59	S/m
60	mS/cm
61	ppb
62	ppt
63	mV/pH
64	spare2
65	spare3
66	rH
67	%/°C
68	%/°F
69	mV/°C
70	pH/°C
71	pH/°F
72	S/cm
73	/m
74	/cm
75	mV/°F
76	Temp. No unit
77	sec
78	kOhm
79	PV.range_dec_pnt
80	Adj CC
81	The calibrated cell constant.
82	Cal point hi
83	The highest calibrated value.
84	Cal point lo
85	The lowest calibrated value.
86	Cal min span
87	The minimum calibration span value allowed.
88	Sensor cal method
89	The method of the last sensor calibration.
90	1 point
91	2 point
92	3 point
93	air
94	other
95	SV.status
96	The status of the secondary value.
97	SV
98	Secondary value (temperature).
99	Temp unit
100	The engineering unit of secondary value.
101	Temp comp
102	Temperature measurement mode.
103	Manual
104	Man value
105	The temperature value used in manual mode.
106	Temp sensor
107	The type of the connected temperature sensor.
108	Pt1000
109	Pt100
110	Ni100
111	8k55
112	Pb36 (JIS6k)
113	Sensor type
114	The type of the connected conductivity sensor.
115	2-elec
116	4-elec
117	Ohms
118	The raw ohms value of the sensor.
119	TC SC1
120	The temperature coefficient of the primary value.
121	PV conc.status
122	The status the primary value concentration.
123	PV conc
124	Primary value concentration.
125	Sensor serial nr
126	Meas unit
127	The cell constant unit.
128	Measure
129	Select process parameter.
130	Cond only
131	Res only
132	Conc only
133	Cond+Conc
134	Method SC1
135	Temperature compensation method.
136	None
137	TC
138	NaCl
139	Matrix
140	Conc unit
141	Concentration unit.
142	%
143	ppm
144	Matrix SC1
145	Selected compensation matrix for primary value.
146	Ammonia 0-50 ppb
147	Morpholine 0-500 ppb
148	Ammonia 15-30 %
149	H2SO4 0-27 %
150	H2SO4 39-85 %
151	H2SO4 93-100 %
152	NaOH 0-15 %
153	NaOH 25-50 %
154	HCl 0-200 ppb
155	HCL 0-18 %
156	HCL 24-44 %
157	HNO3 0-25 %
158	HNO3 35-80 %
159	User defined 1
160	User defined 2
161	Matrix temp rg 1
162	Matrix temperature range 1.
163	Matrix temp rg 2
164	Matrix temperature range 2.
165	Matrix temp rg 3
166	Matrix temperature range 3.
167	Matrix temp rg 4
168	Matrix temperature range 4.
169	Matrix temp rg 5
170	Matrix temperature range 5.
171	Matrix temp rg 6
172	Matrix temperature range 6.
173	Matrix temp rg 7
174	Matrix temperature range 7.
175	Matrix temp rg 8
176	Matrix temperature range 8.
177	Matrix temp rg 9
178	Matrix temperature range 9.
179	Matrix temp rg 10
180	Matrix temperature range 10.
181	Sol.1, Conc.1
182	Solution 1, Concentration 1.
183	Sol.1, Tref
184	Solution 1, reference temperature.
185	Sol.1, Tmin
186	Solution 1, minimum temperature.
187	Sol.1, T2
188	Solution 1, temperature 2.
189	Sol.1, T3
190	Solution 1, temperature 3.
191	Sol.1, T4
192	Solution 1, temperature 4.
193	Sol.1, T5
194	Solution 1, temperature 5.
195	Sol.1, T6
196	Solution 1, temperature 6.
197	Sol.1, T7
198	Solution 1, temperature 7.
199	Sol.1, T8
200	Solution 1, temperature 8.
201	Sol.1, T9
202	Solution 1, temperature 9.
203	Sol.1, Tmax
204	Solution 1, maximum temperature.
205	Sol.2, Conc.2
206	Solution 2, concentration 2.
207	Sol.2, Tref
208	Solution 2, reference temperature.
209	Sol.2, Tmin
210	Solution 2, minimum temperature.
211	Sol.2, T2
212	Solution 2, temperature 2.
213	Sol.2, T3
214	Solution 2, temperature 3.
215	Sol.2, T4
216	Solution 2, temperature 4.
217	Sol.2, T5
218	Solution 2, temperature 5.
219	Sol.2, T6
220	Solution 2, temperature 6.
221	Sol.2, T7
222	Solution 2, temperature 7.
223	Sol.2, T8
224	Solution 2, temperature 8.
225	Sol.2, T9
226	Solution 2, temperature 9.
227	Sol.2, Tmax
228	Solution 2, maximum temperature.
229	Sol.3, Conc.3
230	Solution 3, concentration 3.
231	Sol.3, Tref
232	Solution 3, reference temperature.
233	Sol.3, Tmin
234	Solution 3, minimum temperature.
235	Sol.3, T2
236	Solution 3, temperature 2.
237	Sol.3, T3
238	Solution 3, temperature 3.
239	Sol.3, T4
240	Solution 3, temperature 4.
241	Sol.3, T5
242	Solution 3, temperature 5.
243	Sol.3, T6
244	Solution 3, temperature 6.
245	Sol.3, T7
246	Solution 3, temperature 7.
247	Sol.3, T8
248	Solution 3, temperature 8.
249	Sol.3, T9
250	Solution 3, temperature 9.
251	Sol.3, Tmax
252	Solution 3, maximum temperature.
253	Sol.4, Conc.4
254	Solution 4, concentration 4.
255	Sol.4, Tref
256	Solution 4, reference temperature.
257	Sol.4, Tmin
258	Solution 4, minimum temperature.
259	Sol.4, T2
260	Solution 4, temperature 2.
261	Sol.4, T3
262	Solution 4, temperature 3.
263	Sol.4, T4
264	Solution 4, temperature 4.
265	Sol.4, T5
266	Solution 4, temperature 5.
267	Sol.4, T6
268	Solution 4, temperature 6.
269	Sol.4, T7
270	Solution 4, temperature 7.
271	Sol.4, T8
272	Solution 4, temperature 8.
273	Sol.4, T9
274	Solution 4, temperature 9.
275	Sol.4, Tmax
276	Solution 4, maximum temperature.
277	Sol.5, Conc.5
278	Solution 5, concentration 5.
279	Sol.5, Tref
280	Solution 5, reference temperature.
281	Sol.5, Tmin
282	Solution 5, minimum temperature.
283	Sol.5, T2
284	Solution 5, temperature 2.
285	Sol.5, T3
286	Solution 5, temperature 3.
287	Sol.5, T4
288	Solution 5, temperature 4.
289	Sol.5, T5
290	Solution 5, temperature 5.
291	Sol.5, T6
292	Solution 5, temperature 6.
293	Sol.5, T7
294	Solution 5, temperature 7.
295	Sol.5, T8
296	Solution 5, temperature 8.
297	Sol.5, T9
298	Solution 5, temperature 9.
299	Sol.5, Tmax
300	Solution 5, maximum temperature.
301	Sol.6, Conc.6
302	Solution 6, concentration 6.
303	Sol.6, Tref
304	Solution 6, reference temperature.
305	Sol.6, Tmin
306	Solution 6, minimum temperature.
307	Sol.6, T2
308	Solution 6, temperature 2.
309	Sol.6, T3
310	Solution 6, temperature 3.
311	Sol.6, T4
312	Solution 6, temperature 4.
313	Sol.6, T5
314	Solution 6, temperature 5.
315	Sol.6, T6
316	Solution 6, temperature 6.
317	Sol.6, T7
318	Solution 6, temperature 7.
319	Sol.6, T8
320	Solution 6, temperature 8.
321	Sol.6, T9
322	Solution 6, temperature 9.
323	Sol.6, Tmax
324	Solution 6, maximum temperature.
325	Sol.7, Conc.7
326	Solution 7, concentration 7.
327	Sol.7, Tref
328	Solution 7, reference temperature.
329	Sol.7, Tmin
330	Solution 7, minimum temperature.
331	Sol.7, T2
332	Solution 7, temperature 2.
333	Sol.7, T3
334	Solution 7, temperature 3.
335	Sol.7, T4
336	Solution 7, temperature 4.
337	Sol.7, T5
338	Solution 7, temperature 5.
339	Sol.7, T6
340	Solution 7, temperature 6.
341	Sol.7, T7
342	Solution 7, temperature 7.
343	Sol.7, T8
344	Solution 7, temperature 8.
345	Sol.7, T9
346	Solution 7, temperature 9.
347	Sol.7, Tmax
348	Solution 7, maximum temperature.
349	Sol.8, Conc.8
350	Solution 8, concentration 8.
351	Sol.8, Tref
352	Solution 8, reference temperature.
353	Sol.8, Tmin
354	Solution 8, minimum temperature.
355	Sol.8, T2
356	Solution 8, temperature 2.
357	Sol.8, T3
358	Solution 8, temperature 3.
359	Sol.8, T4
360	Solution 8, temperature 4.
361	Sol.8, T5
362	Solution 8, temperature 5.
363	Sol.8, T6
364	Solution 8, temperature 6.
365	Sol.8, T7
366	Solution 8, temperature 7.
367	Sol.8, T8
368	Solution 8, temperature 8.
369	Sol.8, T9
370	Solution 8, temperature 9.
371	Sol.8, Tmax
372	Solution 8, maximum temperature.
373	Sol.9, Conc.9
374	Solution 9, concentration 9.
375	Sol.9, Tref
376	Solution 9, reference temperature.
377	Sol.9, Tmin
378	Solution 9, minimum temperature.
379	Sol.9, T2
380	Solution 9, temperature 2.
381	Sol.9, T3
382	Solution 9, temperature 3.
383	Sol.9, T4
384	Solution 9, temperature 4.
385	Sol.9, T5
386	Solution 9, temperature 5.
387	Sol.9, T6
388	Solution 9, temperature 6.
389	Sol.9, T7
390	Solution 9, temperature 7.
391	Sol.9, T8
392	Solution 9, temperature 8.
393	Sol.9, T9
394	Solution 9, temperature 9.
395	Sol.9, Tmax
396	Solution 9, maximum temperature.
397	Sol.10, Conc.10
398	Solution 10, concentration 10.
399	Sol.10, Tref
400	Solution 10, reference temperature.
401	Sol.10, Tmin
402	Solution 10, minimum temperature.
403	Sol.10, T2
404	Solution 10, temperature 2.
405	Sol.10, T3
406	Solution 10, temperature 3.
407	Sol.10, T4
408	Solution 10, temperature 4.
409	Sol.10, T5
410	Solution 10, temperature 5.
411	Sol.10, T6
412	Solution 10, temperature 6.
413	Sol.10, T7
414	Solution 10, temperature 7.
415	Sol.10, T8
416	Solution 10, temperature 8.
417	Sol.10, T9
418	Solution 10, temperature 9.
419	Sol.10, Tmax
420	Solution 10, maximum temperature.
421	Additional table
422	Enabling this additional table overrules the concentration values obtained from the matrix (if used).
423	Disable
424	Enable
425	Conc table unit
426	Concentration table unit.
427	PV1
428	Primary value 1 of the table.
429	PV2
430	Primary value 2 of the table.
431	PV3
432	Primary value 3 of the table.
433	PV4
434	Primary value 4 of the table.
435	PV5
436	Primary value 5 of the table.
437	PV6
438	Primary value 6 of the table.
439	PV7
440	Primary value 7 of the table.
441	PV8
442	Primary value 8 of the table.
443	PV9
444	Primary value 9 of the table.
445	PV10
446	Primary value 10 of the table.
447	PV11
448	Primary value 11 of the table.
449	PV12
450	Primary value 12 of the table.
451	PV13
452	Primary value 13 of the table.
453	PV14
454	Primary value 14 of the table.
455	PV15
456	Primary value 15 of the table.
457	PV16
458	Primary value 16 of the table.
459	PV17
460	Primary value 17 of the table.
461	PV18
462	Primary value 18 of the table.
463	PV19
464	Primary value 19 of the table.
465	PV20
466	Primary value 20 of the table.
467	PV21
468	Primary value 21 of the table.
469	CONC1
470	Concentration 1 of the table.
471	CONC2
472	Concentration 2 of the table.
473	CONC3
474	Concentration 3 of the table.
475	CONC4
476	Concentration 4 of the table.
477	CONC5
478	Concentration 5 of the table.
479	CONC6
480	Concentration 6 of the table.
481	CONC7
482	Concentration 7 of the table.
483	CONC8
484	Concentration 8 of the table.
485	CONC9
486	Concentration 9 of the table.
487	CONC10
488	Concentration 10 of the table.
489	CONC11
490	Concentration 11 of the table.
491	CONC12
492	Concentration 12 of the table.
493	CONC13
494	Concentration 13 of the table.
495	CONC14
496	Concentration 14 of the table.
497	CONC15
498	Concentration 15 of the table.
499	CONC16
500	Concentration 16 of the table.
501	CONC17
502	Concentration 17 of the table.
503	CONC18
504	Concentration 18 of the table.
505	CONC19
506	Concentration 19 of the table.
507	CONC20
508	Concentration 20 of the table.
509	CONC21
510	Concentration 21 of the table.
511	TV.status
512	The status of the tertiary value.
513	TV
514	Tertiary value.
515	Method SC2
516	Tertiary temperature compensation method.
517	TC SC2
518	The temperature coefficient of the tertiary value.
519	TV conc.status
520	Status of the tertiary concentration.
521	TV conc
522	Tertiary concentration.
523	TV Conc unit
524	Tertiary concentration unit.
525	Matrix SC2
526	Selected compensation matrix for tertiary value.
527	USP%
528	Percentage of allowable Conductivity value at the measured temperature.
529	USP safety margin
530	The safety margin of USP.
531	Polarization
532	Polarization. Less than 15 is OK.
533	Ref temp
534	Reference temperature.
535	Temp offset
536	Temperature offset.
537	Dev alarm
538	Cond too high
539	Res too low
540	Error if conductivity value is too high or resistivity too low.
541	Off
542	Warn
543	Fail
544	Cond too low
545	Res too high
546	Error if conductivity value is too low or resistivity too high.
547	Temp too high
548	Error if temperature is too high.
549	Temp too low
550	Error if temperature is too low.
551	Pol detected
552	Error if polarization limit (15) has been exceeded.
553	USP limit exc
554	Error if USP limit has been exceeded.
555	Conc table
556	Error if concentration table configuration failed.
557	2nd comp mtrx
558	Error if second matrix configuration failed.
559	1st comp mtrx
560	Error if first matrix configuration failed.
561	Cal time exc
562	Error if calibration time exceeded.
563	Warn logbook full
564	Warning if logbook is (almost) full.
565	No
566	Yes
567	Cal interval
568	Calibration interval.
569	Stab time
570	The period in which the drift is less than the pre-programmed tolerance (1 % of last value).
571	Start air adjust
572	Start air calibration.
573	Idle
574	Start
575	Succeeded
576	Failed
577	Busy
578	Air adjust offset
579	Offset after air calibration.
580	Air adjust limit
581	Air calibration limits.
582	Fact CC
583	The nominal cell constant.
584	CC hi lim.
585	Cell constant high limit.
586	CC lo lim.
587	Cell constant low limit.
588	logbook id
589	logbook identifier.
590	Calibration
591	Sensor
592	Predictive Maint.
593	logbook page
594	Erase logbook
595	All logbooks
596	Erase?
597	Logbook event
598	Logbook value
599	Logbook op_id
600	Logbook unit
601	Logbook time high
602	Logbook time low
603	Logbook status
604	Sensor logbook
605	Select if logbook event has to be logged.
606	Error on
607	Error off
608	Temp. Coeff.
609	Adj CC lo lim
610	Adj CC hi lim
611	Reference temp
612	Stab. time
613	Uncomp SC
614	Uncompensated value.
615	SC hi lim
616	Res lo lim
617	Conductivity high limit or resistivity low limit.
618	SC lo lim
619	Res hi lim
620	Conductivity low limit or resistivity high limit.
621	Sample taken
622	FALSE
623	TRUE
624	primary value
625	tertiary value
626	secondary value
627	Status of the primary value.
628	Status of the secondary value.
629	Secdondary value.
630	SV.range_units
631	Status of the tertiary value.
632	TV.range_units
633	Output Target mode
634	Actual mode
635	HOLD 0/1
636	If Hold enabled a mA output is frozen when the HOLD condition occurs.
637	disabled
638	enabled
639	HOLD L/F
640	Select if the output will hold the last mA value or set a fixed mA value if the hold condition occurs.
641	last
642	fixed
643	HOLD during cal
644	Select if HOLD is set during calibration.
645	Year
646	02d
647	Month
648	Day
649	Hour
650	Minute
651	Second
652	PID Dir
653	PID direction.
654	direct
655	reverse
656	Calculation
657	value 1
658	value 2
659	ratio
660	differential
661	passage
662	rejection
663	deviation
664	Status
665	Oos
666	Hold
667	Underflow
668	Overflow
669	Route1_error
670	Route2_error
671	Calc_error
672	Expire_error
673	Soft fail
674	Hard fail
675	Simulate
676	Type
677	Configure contact to a specific type.
678	Control
679	Alarm
680	HOLD
681	USP
682	Func
683	Configure type to a specific function.
684	P
685	PI
686	PID
687	Hard + Soft Fail
688	On/Off
689	Percentage
690	Hard Fail only
691	Alarm SP
692	Alarm setpoint.
693	Alarm dir.
694	Alarm direction.
695	low
696	high
697	Alarm hyst.
698	Alarm hysteresis.
699	Alarm delay
700	Alarm delay time.
701	PID SP
702	PID setpoint.
703	PID Rng
704	PID range.
705	PID MR
706	PID manual reset. Static output (%) when Setpoint is equal to the measured value.
707	PID I time
708	PID I time.
709	PID D time
710	PID D time. 0 (zero) for off.
711	Contact
712	Digital simulate contact.
713	On
714	Analog simulate contact.
715	Analog output
716	Analog output type.
717	DC
718	PF
719	DC time
720	Duty cycle time.
721	Max freq
722	Maximum pulse frequency.
723	Expire time
724	If the output is outside it’s range for longer than the expire time, the output will return to 0%. 0 (zero) for off.
725	Contact logbook
726	Select which contact logbook event has to be logged.
727	Contact setup
728	PID setpoint
729	PID range
730	Manual reset
731	Control type
732	DC period time
733	Max pulse freq.
734	Alarm setpoint
735	Alarm direction
736	Alarm hysteresis
737	Alarm delay time
738	S1 perc
739	Contact percentage.
740	C1.unit
741	Contact unit.
742	Param
743	Select process parameter. Valid parameters are: CONDUCT,CONDUCT2 and TEMPERATURE.
744	Select process parameter. Valid parameters are: CONDUCT,CONCENT and TEMPERATURE.
745	Select process parameter. Valid parameters are: RESIST1,RESIST2 and TEMPERATURE.
746	Select process parameter. Valid parameters are: CONCENT1,CONCENT2 and TEMPERATURE.
747	NONE
748	CONDUCT
749	TEMPERATURE
750	CONDUCT2
751	CONCENT
752	RESIST1
753	RESIST2
754	CONCENT1
755	CONCENT2
756	S2 perc
757	C2.unit
758	Route1error
759	S3 perc
760	C3.unit
761	S4 perc
762	C4.unit
763	Table_error
764	Burn low
765	Burn high
766	Confige output to a specific type.
767	Output
768	Confige type to a specific function.
769	Linear
770	Table
771	Damping time
772	The response to a step input change reaches approximately 90 percent of its final value within the damping time. 0 (zero) for off.
773	Simulation percentage.
774	mA1 fixed
775	Fixed output value.
776	Burn
777	If error occur, burn set output to low or high.
778	Low
779	High
780	mA logbook
781	Select which output logbook event has to be logged.
782	mA setup
783	Hold fixed value
784	Linear %
785	Lin 0%
786	Linear 0%.
787	Lin 100%
788	Linear 100%.
789	mA1 perc
790	Output percentage.
791	mA1 value
792	Output value.
793	M1.unit
794	Calculation unit.
795	%01
796	Output percentage 1.
797	%02
798	Output percentage 2.
799	%03
800	Output percentage 3.
801	%04
802	Output percentage 4.
803	%05
804	Output percentage 5.
805	%06
806	Output percentage 6.
807	%07
808	Output percentage 7.
809	%08
810	Output percentage 8.
811	%09
812	Output percentage 9.
813	%10
814	Output percentage 10.
815	%11
816	Output percentage 11.
817	%12
818	Output percentage 12.
819	%13
820	Output percentage 13.
821	%14
822	Output percentage 14.
823	%15
824	Output percentage 15.
825	%16
826	Output percentage 16.
827	%17
828	Output percentage 17.
829	%18
830	Output percentage 18.
831	%19
832	Output percentage 19.
833	%20
834	Output percentage 20.
835	%21
836	Output percentage 21.
837	Val01
838	Output value 1.
839	Val02
840	Output value 2.
841	Val03
842	Output value 3.
843	Val04
844	Output value 4.
845	Val05
846	Output value 5.
847	Val06
848	Output value 6.
849	Val07
850	Output value 7.
851	Val08
852	Output value 8.
853	Val09
854	Output value 9.
855	Val10
856	Output value 10.
857	Val11
858	Output value 11.
859	Val12
860	Output value 12.
861	Val13
862	Output value 13.
863	Val14
864	Output value 14.
865	Val15
866	Output value 15.
867	Val16
868	Output value 16.
869	Val17
870	Output value 17.
871	Val18
872	Output value 18.
873	Val19
874	Output value 19.
875	Val20
876	Output value 20.
877	Val21
878	Output value 21.
879	mA2 fixed
880	mA2 perc
881	mA2 value
882	M2.unit
883	output logbook id
884	Settings
885	mA1
886	mA2
887	S1
888	S2
889	S3
890	S4
891	output logbook page
892	Logbook event output
893	Logbook value output
894	Logbook op_id output
895	Logbook unit output
896	Logbook time high output
897	Logbook time low output
898	Logbook status output
899	Input contact
900	Select the function of the input contact.
901	Disabled
902	Factor 10 mA1
903	Factor 10 mA2
904	Factor 10 mA1+2
905	Device Revision
906	Software Revision
907	Serial number
908	Tag
909	Most appl. error
910	Most applicable error
911	Logbook erased
912	Defaults loaded
913	Initialization
914	Temperature offset
915	SC offset
916	c.c. factory
917	c.c. adjusted
918	Logbook saved
919	Operator ID
920	Powerup
921	Powerdown
922	Error on: conductivity too high
923	Error on: conductivity too low
924	Error on: temperature too high
925	Error on: temperature too low
926	Error on: compensation SC1
927	Error on: compensation SC2
928	Error on: measurement unstable
929	Error on: polarization
930	Error on: USP limit
931	Error on: USP margin
932	Error on: table error
933	Error on: matrix2 error
934	Error on: matrix1 error
935	Error on: calibration due
936	Error on: eeprom
937	Error on: checksum
938	Error off: conductivity too high
939	Error off: conductivity too low
940	Error off: temperature too high
941	Error off: temperature too low
942	Error off: compensation SC1
943	Error off: compensation SC2
944	Error off: measurement unstable
945	Error off: polarization
946	Error off: USP limit
947	Error off: USP margin
948	Error off: table error
949	Error off: matrix2 error
950	Error off: matrix1 error
951	Error off: calib. time
952	Error off: eeprom
953	Temp. coef.
954	SC offset low limit
955	Adj. c.c. low limit
956	Adj. c.c. high limit
957	Reference temp.
958	Stabilization time
959	Power on
960	Power off
961	SYSTEM ERROR
962	Hold disabled
963	Hold enabled
964	Hold last
965	Hold fixed
966	Output range 0-20 mA
967	Output range 4-20 mA
968	User defaults saved
969	Factory defaults loaded
970	User defaults loaded
971	Alarm direction low
972	Alarm direction high
973	Hysteresis
974	PID I-time
975	PID D-time
976	Max pulse freq
977	Expiry time
978	Type off
979	Type control
980	Type alarm
981	Type fail
982	Type simulate
983	Type hold
984	Function off
985	Function P-control
986	Function PI-control
987	Function PID-control
988	Function alarm
989	Function wash
990	Function hard+soft fail
991	Function simulate on/off
992	Function simulate perc.
993	Function hard fail only
994	Function hold
995	Duty-cycle output
996	Pulse-frequency output
997	Deenergised when off
998	Burn off
999	Type output
1000	Function linear
1001	Function table
1002	Linear 0%
1003	Linear 100%
1004	S1 on
1005	S1 off
1006	S2 on
1007	S2 off
1008	S3 logbook erased
1009	S3 on
1010	S3 off
1011	S4 logbook erased
1012	S4 on
1013	S4 off
1014	mA1 low
1015	mA1 high
1016	mA1 operational
1017	mA2 low
1018	mA2 high
1019	mA2 operational
1020	DD Revision 01
1021	Hold ON
1022	Hold OFF
1023	Select Manual Hold function for the instrument. Set Hold to ON to freeze the outputs and to be able to change any parameter. Set Hold to OFF for live outputs.
1024	Sensor data
1025	Output data
1026	Set date/time
1027	Temp. Calibration
1028	CC Calibration SC1
1029	CC Calibration SC2
1030	Sample Calib. SC1
1031	Sample Calib. SC2
1032	TC Calibration SC1
1033	TC Calibration SC2
1034	Air Calibration
1035	Hot Key Menu
1036	Information
1037	Process values
1038	Zoom
1039	Zoom sensor
1040	Zoom outputs
1041	Zoom device
1042	Logbook
1043	Commissioning
1044	Measurement setup
1045	Configure sensor
1046	Temp settings
1047	Temp compensation
1048	Calib. settings
1049	Concentration
1050	Output setup
1051	Inp. contact setup
1052	mA1 setup
1053	mA2 setup
1054	S1 setup
1055	S2 setup
1056	S3 setup
1057	S4 setup
1058	HOLD setup
1059	Error config
1060	Logbook config
1061	Write variables
1062	Undefined
1063	Parameter too large
1064	Parameter too small
1065	In write protect mode
1066	Invalid unit code
1067	Span too small
1068	Device is busy
1069	Command not implemented
1070	FMU860
1071	DT
1072	DVC
1073	FCX
1074	AS800
1075	340T
1076	340C
1077	344
1078	Siemens Micro K
1079	SITRANS L
1080	SIPAN PH
1081	SITRANS P
1082	75SMT
1083	UNIDELTA
1084	8320
1085	SX5100
1086	TSV175
1087	DMU
1088	3780
1089	BM70
1090	8u
1091	Set Hold ?
1092	Hold ON;Hold OFF
1093	No errors
1094	Programmed data lost Remedy: Contact your local Yokogawa sales office.
1095	Checksum error Remedy: Contact your local Yokogawa sales office.
1096	Initialization error Remedy: Contact your local Yokogawa sales office.
1097	Measurement not working Remedy: Go to HOLD menu and set HOLD to OFF or OUTPUTS.
1098	Conductivity too high Remedy: Check con- nections and cable. Replace sensor. Adjust limits in: Error configuration
1099	Conductivity too low Remedy: Check con- nections and cable. Replace sensor. Adjust limits in: Error configuration
1100	Temperature too high Remedy: Check process temperature. Check selected sensortype. Check connections and cable.
1101	Temperature too low Remedy: Check process temperature. Check selected sensortype. Check connections and cable.
1102	Polarization detected Remedy: Clean or replace sensor. Adjust process.
1103	USP limit exceeded Remedy: Check ion exchangers.
1104	USP margin exceeded Remedy: Check ion exchangers.
1105	Error in conc. table Remedy: Execute 'Check values' in: Commissioning » Meas. setup » Concentr. » Define table.
1106	Error in 2nd matrix Remedy: Execute 'Check values' in: Commissioning » Meas. setup » Temp. comp. » Matrix.
1107	Error in 1st matrix Remedy: Execute 'Check values' in: Commissioning » Meas. setup » Temp. comp. » Matrix.
1108	Calibration scheduled Remedy: Perform maintenance. Reset interval.
1109	TC error (SC1) Remedy: Check temp. compensation config. in: Commissioning » Meas. setup » Temp. comp.
1110	TC error (SC2) Remedy: Check temp. compensation config. in: Commissioning » Meas. setup » Temp. comp. (method2)
1111	Logbook (almost) full Remedy: Save or erase logbooks. Turn logbook warning off.
1112	Measurement unstable Remedy: Check con- nections and cable. Check fluid for bubbles.
1113	mA underflow Remedy: Check process. Adapt 0% value. Adapt setpnt./range.
1114	mA overflow Remedy: Check process. Adapt 100% value. Adapt setpnt./range.
1115	mA configuration error Remedy: Select a correct process parameter in the setup menu.
1116	mA configuration error Remedy: Contact your local Yokogawa sales office.
1117	mA calculation error Remedy: Check process parameter for mA output.
1118	Error in mA table Remedy: Read the message in the table setup menu.
1119	mA burn low Remedy: Check measured process values.
1120	mA burn high Remedy: Check measured process values.
1121	Simulated mA value Remedy: Re-configure in setup.
1122	Expiry time exceeded Remedy: Check control equipment. Adjust timer value in setup.
1123	Reset expiry time error?
1124	None;Only mA1;Only mA2;Both mA1 and mA2
1125	?
1126	Contact underflow Remedy: Check process. Adapt setpnt./range.
1127	Contact overflow Remedy: Check process. Adapt setpnt./range.
1128	Contact configuration error Remedy: Select a correct process parameter in the setup menu.
1129	Contact configuration error Remedy: Contact your local Yokogawa sales office.
1130	Calculation error Remedy: Check process parameter for contacts.
1131	None;Only S1;Only S2;Only S3;Only S4;All contacts
1132	Soft fail Remedy: Check measured process values.
1133	Hard fail Remedy: Check measured process values.
1134	Simulated contact Remedy: Re-configure in setup.
1135	Outputs in hold Remedy: Go to HOLD menu and set HOLD to OFF.
1136	Unknown error-code error-code = %{0}
1137	Select logbook
1138	Calibration;Sensor;Pred.Maint.
1139	All events read
1140	nr:%{nr} %{yr}-%[02d]{mth}-%[02d]{day} %[02d]{hr}:%[02d]{min}:%[02d]{sec} %{1} '%{2}%{3}%{4}%{5}'
1141	nr:%{nr} %{yr}-%[02d]{mth}-%[02d]{day} %[02d]{hr}:%[02d]{min}:%[02d]{sec} %{1}
1142	nr:%{nr} %{yr}-%[02d]{mth}-%[02d]{day} %[02d]{hr}:%[02d]{min}:%[02d]{sec} %{1} %[.3g]{fValue} %{0}
1143	nr:%{nr} %{yr}-%[02d]{mth}-%[02d]{day} %[02d]{hr}:%[02d]{min}:%[02d]{sec} %{1} %[.3g]{fValue} %{0}
1144	nr:%{nr} %{yr}-%[02d]{mth}-%[02d]{day} %[02d]{hr}:%[02d]{min}:%[02d]{sec} %{1} %[.0f]{fValue}
1145	nr:%{nr} Unknow logbook Event: %{iEvent}
1146	Settings;mA1;mA2;S1;S2;S3;S4
1147	nr:%[02d]{nr} %{yr}-%[02d]{mth}-%[02d]{day} %[02d]{hr}:%[02d]{min}:%[02d]{sec} %{1}
1148	nr:%[02d]{nr} %{yr}-%[02d]{mth}-%[02d]{day} %[02d]{hr}:%[02d]{min}:%[02d]{sec} %{1} %[.2g]{fValue} %{0}
1149	nr:%[02d]{nr} %{yr}-%[02d]{mth}-%[02d]{day} %[02d]{hr}:%[02d]{min}:%[02d]{sec} S%[1d]{out}:%{1}
1150	nr:%[02d]{nr} %{yr}-%[02d]{mth}-%[02d]{day} %[02d]{hr}:%[02d]{min}:%[02d]{sec} S%[1d]{out}:%{1} %[.3g]{fValue} %{0}
1151	nr:%[02d]{nr} %{yr}-%[02d]{mth}-%[02d]{day} %[02d]{hr}:%[02d]{min}:%[02d]{sec} mA%[1d]{out}:%{1}
1152	nr:%[02d]{nr} %{yr}-%[02d]{mth}-%[02d]{day} %[02d]{hr}:%[02d]{min}:%[02d]{sec} mA%[1d]{out}:%{1} %[.3g]{fValue} %{0}
1153	nr:%[02d]{nr} Unknow logbook Event: %{iEvent}
1154	Are you sure?
1155	No;Yes
1156	Input day
1157	Input month
1158	Input year
1159	Input hour
1160	Input minute
1161	Input second
1162	Change date/time %{0}/%{1}/%{2} %{3}:%{4}:%{5}
1163	Measured Temperature %[0.1f]{local_Temp} %{0} Adjust now
1164	New value
1165	Offset is out of limit
1166	Calib. completed %[0.1f]{local_Temp_new} %{0} Temp Offset = %[0.1f]{local_Offset_new} %{0}
1167	%[.3e]{local_pv} %{5} %[.1f]{0} %{1} Adjust now
1168	c.c. out of limits
1169	Calibration complete Factory c.c.: %[.3f]{6} %{2} Adjusted c.c.: %[.3f]{local_new_cc} %{2} Accept data
1170	%[.3e]{local_tv} %{5} %[.1f]{0} %{1} Adjust now
1171	%[.3e]{local_pv} %{5} %[.1f]{0} %{1} Take Sample
1172	Sample Taken %[.3e]{sample_pv} %{5} %[.1f]{sample_temp} %{1}
1173	%[.3e]{local_pv} %{5} %[.1f]{0} %{1} %[.3e]{sample_pv} %{5} %[.1f]{sample_temp} %{1}
1174	Start calibration;Del. stored sample
1175	%[.3e]{local_tv} %{5} %[.1f]{0} %{1} Take Sample
1176	Sample Taken %[.3e]{sample_tv} %{5} %[.1f]{sample_temp} %{1}
1177	%[.3e]{local_tv} %{5} %[.1f]{0} %{1} %[.3e]{sample_tv} %{5} %[.1f]{sample_temp} %{1}
1178	Temp.coef. out of limits
1179	New Temp. coef.: %[.2f]{local_new_tc} %/%{1} Accept data
1180	Temp. coef. out of limits
1181	Remove sensor from solution. Offset = %{0} S Adjust now
1182	Air calibration busy. PLEASE WAIT ...
1183	Air calibration succeeded. Offset = %{0} S
1184	Air calibration failed. Is sensor taken from solution? Try again?
1185	Remark: Set Hold to ON to freeze the outputs and to be able to change any parameter.
引用ID	字符串