Device dictionary

Loading…

Reference ID	String
0	OFF
1	RCCT_F3
2	Yokogawa
3	8u
4	Error group 1
5	Frequency Fault
6	Signal Fault
7	EEPROM Fault
8	CPU Fault
9	DSP Fault
10	Sens1 Sig Fault
11	Sens2 Sig Fault
12	Temp Sens Fault
13	Error group 2
14	DP Config Fault
15	DP Comm Fault
16	DP Count Fault
17	Fault 12
18	Fault 13
19	Fault 14
20	Fault 15
21	Fault 16
22	Alarm group 1
23	Mass flo L alm
24	Mass flo H alm
25	Vol flo L alm
26	Vol flo H alm
27	Dens L alm
28	Dens H alm
29	Temp L alm
30	Temp H alm
31	Alarm group 2
32	Conc L alm
33	Conc H alm
34	Net flo L alm
35	Net flo H alm
36	Total thr exceed
37	Slug Detection
38	Empty Pipe Det.
39	Corrosion Detect
40	Warning group 1
41	Dens val<0.3kg/l
42	Fix dens active
43	Fix temp active
44	Fix massflo act.
45	AZ in progress
46	AZ value overrng
47	AZ fluct overrng
48	Sens simul activ
49	Warning group 2
50	Ana out1 fixed
51	Ana out1 sat
52	Ana out2 sat
53	Pls out1 sat
54	Pls out2 sat
55	Warning 14
56	Warning 15
57	Warning 16
58	Error status 1
59	Snsr1 Sig Fault
60	Snsr2 Sig Fault
61	Temp Snsr Fault
62	Error status 2
63	Alarm status 1
64	Alarm status 2
65	Warning status 1
66	Dens val<0.3 kg/l
67	Warning status 2
68	t/min
69	t/h
70	t/d
71	7.0f
72	7.1f
73	7.2f
74	7.3f
75	7.4f
76	7.5f
77	Mass flo format
78
79	XXXXXXX
80	XXXXX.X
81	XXXX.XX
82	XXX.XXX
83	XX.XXXX
84	X.XXXXX
85	Mass flo alm 1 crit
86	Mass flo alm 1 select
87	No Function
88	More Than
89	Less Than
90	Mass flo alm 2 crit
91	Mass flo alm 2 select
92	Mass flo damp
93	Sec
94	5.1f
95	Mass flo lowcut
96	cm3/s
97	cm3/min
98	cm3/h
99	m3/s
100	m3/min
101	m3/h
102	L(N)/s
103	L(N)/min
104	L(N)/h
105	m3(N)/s
106	m3(N)/min
107	m3(N)/h
108	L/d
109	m3/d
110	L(N)/d
111	m3(N)/d
112	L(Std)/s
113	L(Std)/min
114	L(Std)/h
115	L(Std)/d
116	StdCuft/s
117	StdCuft/min
118	StdCuft/h
119	StdCuft/d
120	m3(Std)/s
121	m3(Std)/min
122	m3(Std)/h
123	m3(Std)/d
124	Vol flo format
125	Vol flo lowcut
126	Vol flo damp
127	Vol flo alm 1 crit
128	Vol flo alm 1 select
129	Vol flo alm 2 crit
130	Vol flo alm 2 select
131	kg/m3
132	g/cm3
133	Dens format
134	Dens damp
135	Dens lowcut
136	Dens alm 1 crit
137	Dens alm 1 select
138	Dens alm 2 crit
139	Dens alm 2 select
140	Density offset
141	Adjust offset of density measurement
142	g/l
143	4.2f
144	K
145	Temp format
146	Temp damp
147	Temp lowcut
148	Temp alm 1 crit
149	Temp alm 1 select
150	Temp alm 2 crit
151	Temp alm 2 select
152	Velocity unit
153	Velocity
154	6.4f
155	Total flex unit
156	cm3
157	m3
158	L(N)
159	m3(N)
160	t
161	kgal
162	kImpgal
163	L(Std)
164	StdCuft
165	MMscuft
166	m3(Std)
167	F-Total flex
168	12.1f
169	F-Total format
170	F-Total damp
171	F-Total lowcut
172	Total Unit
173	R-Total flex
174	R-Total format
175	R-Total damp
176	R-Total Lowcut
177	D-Total flex
178	D-Total format
179	D-Total damp
180	D-Total lowcut
181	Disp select 1
182	Select the variable to be displayed at this line at the device.
183	Mass flo
184	Vol flo
185	Dens
186	Temp
187	F-Totl flex
188	R-Totl flex
189	D-Totl flex
190	F-Totl mass
191	R-Totl mass
192	D-Totl mass
193	F-Totl vol
194	R-Totl vol
195	D-Totl vol
196	F-Totl energy
197	Drive gain
198	Conc meas
199	Net flo
200	F-Totl net
201	R-Totl net
202	D-Totl net
203	Disp select 2
204	None
205	Disp select 3
206	Disp select 4
207	Display contrast
208	Choose the contrast of the device display.
209	-5
210	-4
211	-3
212	-2
213	-1
214	0
215	+1
216	+2
217	+3
218	+4
219	+5
220	Display period
221	Choose the update period of the device display.
222	0.5 sec
223	1.0 sec
224	2.0 sec
225	Start LCD/Key Test
226	Starts a selftest routine on the LCD panel.
227	Not apply
228	Apply LCD
229	Apply Key
230	Language
231	Select language
232	English
233	German
234	French
235	Russian
236	FL20 adjust exe
237	Not apply
238	Apply
239	KD adjust exe
240	Total res cntrl
241	Inhibit
242	Enable
243	Total res exe
244	Not execute
245	Reset flex totals
246	Reset mass totals
247	Reset volume totals
248	Reset all totals
249	Reset net totals
250	Total switch select
251	Flex total
252	Mass total
253	Volume total
254	Net total
255	Total flex select
256	Mass
257	Volume
258	Net
259	Total at alarm
260	Hold
261	Continue
262	Pulse/Freq 1
263	6.1f
264	Pls width
265	0.05 msec
266	0.1 msec
267	0.5 msec
268	1 msec
269	5 msec
270	10 msec
271	50 msec
272	100 msec
273	500 msec
274	1000 msec
275	50%
276	Active mode
277	On Active
278	Off Active
279	At alarm
280	0 Hz / 0 Pulses
281	Measured value
282	Pulse/Freq 2
283	Pulse/Stat 1 sel
284	Pulse/Stat A sel
285	Pulse
286	Status Out
287	Pulse/Stat B sel
288	Pulse/Stat 2 sel
289	Pulse 1 rate
290	Pulse 2 rate
291	Pulse 1 unit
292	cm3/P
293	L/P
294	m3/P
295	L(N)/P
296	m3(N)/P
297	g/P
298	kg/P
299	t/P
300	Hz
301	gal/P
302	kgal/P
303	Cuft/P
304	bbl/P
305	Impgal/P
306	kImpgal/P
307	L(Std)/P
308	StdCuft/P
309	m3(Std)/P
310	lb/P
311	Pulse 2 unit
312	Pulse B rate
313	Pulse B unit
314	Pulse/Freq B
315	Active mode B
316	At alarm B
317	SI active mode
318	Select trigger level for binary input
319	Input function
320	Select the function of binary input
321	Autozero
322	0% Signal Lock
323	SO A active mode
324	SO 1 active mode
325	SO A function
326	SO 1 function
327	Flow direction
328	Total Switch
329	Mass flo alm 1
330	Mass flo alm 2
331	Mass flo alm 1&2
332	Vol flo alm 1
333	Vol flo alm 2
334	Vol flo alm 1&2
335	Dens alm 1
336	Dens alm 2
337	Dens alm 1&2
338	Temp alm 1
339	Temp alm 2
340	Temp alm 1&2
341	Slug Alarm
342	Empty Alarm
343	Corrosion Alarm
344	All Alarms
345	All Errors
346	All Alarms & Errors
347	Conc alm 1
348	Conc alm 2
349	Conc alm 1&2
350	Net flo alm 1
351	Net flo alm 2
352	Net flo alm 1&2
353	SO B active mode
354	SO B function
355	SO 2 active mode
356	SO 2 function
357	Analog 1 out
358	6.3f
359	Analog 2 out
360	% range 1 out
361	%
362	% range 2 out
363	Analog 1 low LMT
364	mA
365	Analog 2 low LMT
366	Analog 1 high LMT
367	Analog 2 high LMT
368	Sensor S/N
369	Serial no. converter
370	Serial no. of the converter.
371	Serial no. detector
372	Serial no. of the detector.
373	Forward
374	Reverse
375	Temp fix val sel
376	Temp fixed value
377	Temp gain adjust
378	Temp offset
379	Adjust offset of temperature measurement
380	Fluid max temp
381	Ref density sel
382	Fixed
383	Calculated
384	Reference density
385	Dens ref value
386	Mass flo fix sel
387	Mass flo fixed val
388	Heat of combustion
389	Heat of combustion value
390	Heat of combu unit
391	Heat of combustion unit
392	MJ/kg
393	MJ/m3(N)
394	Btu/lb
395	Btu/StdCuft
396	Device S/W date
397	Device S/W version
398	Burn out
399	Burn out State of the Electronic Transmitter
400	<3.6 mA
401	>21.0 mA
402	Key status
403	Long Tag
404	Long Tag- Text that is associated with the Field Device installation.
405	Alarm 1 select
406	<2.40 mA
407	<3.60 mA(lo)
408	4.00 mA
409	>21.00 mA(hi)
410	>21.60 mA
411	Hold
412	Measured value
413	Hold
414	Alarm 2 select
415	Total limit switch
416	Sets the totalizer to the value defined here
417	10.3f
418	Zero tuning
419	Autozero duration
420	3 Min
421	30 Sec
422	Autozero value
423	kg/h
424	8.3f
425	AZ fluctuation
426	Data Set:
427	1 Newest
428	2
429	3
430	4
431	5 Oldest
432	Initial
433	Date index :
434	AZ
435	Err
436	Val:
437	Dens:
438	Temp:
439	6.2f
440	Date:
441	Date in format (mm/dd/yyyy)
442	Coeff a units
443	E-3*1/degC
444	E-3*1/degF
445	E-3*1/K
446	Coeff b units
447	E-5*1/degC²
448	E-5*1/degF²
449	E-5*1/K²
450	Ref. temperature
451	Reference temperature (where reference density is measured)
452	Ref. dens. carrier
453	Reference density (measured at reference temperature)
454	Ref. dens. product
455	Coeff. a carrier
456	Linear temperature coefficient for change of density
457	5.4f
458	7.6f
459	Temp. coeff a
460	Coeff. a product
461	Coeff. b carrier
462	Squared temperature coefficient for change of density
463	Temp. coeff b
464	Coeff. b product
465	Conc version
466	3d
467	Conc meas sel
468	Advanced
469	Standard
470	NetOil
471	Selected Set:
472	1
473	2
474	3
475	4
476	5
477	6
478	7
479	8
480	No of Para sets
481	Parameter sets help
482	2d
483	Tmp:
484	Temperature help
485	P_A:
486	Parameter Input help
487	10.5f
488	P_B:
489	P_C:
490	P_D:
491	Error :
492	Alarm :
493	Warning:
494	ord_hist
495	E-
496	A-
497	W-
498	ord_err
499	01 Frequency Fault
500	02 Signal Fault
501	03 EEPROM Fault
502	04 CPU Fault
503	05 DSP Fault
504	06 Sens1 Sig Fault
505	07 Sens2 Sig Fault
506	08 Temp Sens Fault
507	09 Not used
508	10 Not used
509	11 Not used
510	12 Not used
511	13 Not used
512	14 Not used
513	15 Not used
514	16 Not used
515	01 Mass flo L alm
516	02 Mass flo H alm
517	03 Vol flo L alm
518	04 Vol flo H alm
519	05 Dens L alm
520	06 Dens H alm
521	07 Temp L alm
522	08 Temp H alm
523	09 Conc L alm
524	10 Conc H alm
525	11 Net flo L alm
526	12 Net flo H alm
527	13 Total thr exceed
528	14 Slug Detection
529	15 Empty Pipe Detect
530	16 Corrosion Detect
531	01 Dens val<0.3kg/l
532	02 Fix dens active
533	03 Fix temp active
534	04 Fix massflo active
535	05 AZ in progress
536	06 AZ value overrng
537	07 AZ fluct overrng
538	08 Sens simul activ
539	09 Ana out1 fixed
540	10 Ana out1 sat
541	11 Ana out2 sat
542	12 Pls out1 sat
543	13 Pls out2 sat
544	No Error/Alarm/Warning
545	History Set
546	Abs
547	Set1
548	Set2
549	Set3
550	Set4
551	Set5
552	Set6
553	Set7
554	Set8
555	Set9
556	Set10
557	H.Error :
558	H.Alarm :
559	H.Warning:
560	Errors Help
561	Clear History ord
562	Execute
563	Read freq
564	LV_HV_adjust_mode
565	LV
566	HV
567	Status mode
568	OFF
569	ON
570	SO 1 mode
571	SO A mode
572	ON
573	SO 2 mode
574	SO B mode
575	Status in mode
576	Open
577	Short
578	Output status code
579	Status 1
580	Status 2
581	Status in
582	Status B
583	Analog 1 Zero
584	Analog 1 Span
585	Analog 2 Zero
586	Analog 2 Span
587	Slug alarm select
588	Slug criteria
589	V
590	Slug duration
591	After slug
592	Drive gain damping
593	Empty pipe alm sel
594	After empty pipe
595	Massflow = zero
596	Empty pipe crit
597	Corrosion alm sel
598	Corrosion crit
599	Corrosion damp
600	h
601	Enable wrt password
602	New_password
603	Type in new password, up to 8 characters are allowed
604	Software seal
605	Break
606	Keep
607	ROTA password
608	Manufacturers password, for service use
609	Password code
610	Type in the correct user password, if no password is defined yet, type all spaces
611	Act
612	New
613	tokuchu code
614	Std total (2)
615	Multi Total (3)
616	Service menu
617	TBD by ROTA
618	closed
619	open
620	Sensor model
621	Actual sensor model
622	RCCS30LR
623	RCCS30
624	RCCS31
625	RCCS32
626	RCCS33
627	RCCS34
628	RCCS36
629	RCCS38
630	RCCS39
631	RCCS39/IR
632	RCCS39/XR
633	SK20
634	Massflow calibration constant
635	MHz*kg/h
636	SKT
637	SKT calibration constant
638	E-4*1/K
639	9.3f
640	SKTK
641	SK 20 temp. correction squared
642	E-7*(1/K)^2
643	8.4f
644	RV
645	RV calibration constant
646	%/(kg/l)
647	Qnom
648	Nominal flow constant
649	KD
650	Density calibration constant
651	kg/l
652	Fl20
653	Resonant frequency of sensor with empty tubes
654	FTC1
655	Temp. correction calibration constant 1
656	FTCK
657	Temp. correction calibration constant k
658	FPC
659	Press. correction coefficient
660	E-4*1/bar
661	SKP
662	Press. correction
663	FQC1
664	FQC1 constant
665	E-10*s/g
666	FQC2
667	FQC2 constant
668	E-13*(s/g)^2
669	SKPT
670	Pressure/temperature compensation
671	E-71/(barK)
672	FPTC
673	RES1
674
675	RES2
676	RES3
677	Pressure
678	Pressure Unit
679	Liquid/Gas select
680	Liquid
681	Gas
682	Exi Out select
683	Exi
684	Exi-Special: 2x Iout
685	Temp range select
686	High Temp
687	Max temp reset
688	Measuring range
689	NAMUR
690	Not NAMUR
691	AO1 Zero
692	AO1 Span
693	AO2 Zero
694	AO2 Span
695	T0
696	Ohm
697	T100
698	TBar
699	MF value 1
700	9.5f
701	MF error 1
702	MF value 2
703	MF error 2
704	MF value 3
705	MF error 3
706	MF value 4
707	MF error 4
708	MF value 5
709	MF error 5
710	MF value 6
711	MF error 6
712	Flow direction hys
713	Flow
714	Conc
715	% sol-wt
716	Curr
717	DSP Reset
718	DSP Reset perm
719	DSP error freque
720	Drive gain limit
721	Amplitude limit
722	Amplitude level
723	DSP amplitude level
724	1/1
725	1/2
726	1/4
727	1/8
728	AZ range
729	Last fluctuation
730	AZ fluct. range
731	AZ factory val
732	AAZQRF range
733	AAZQRF range value
734	AAZQRF range unit
735	AAZ-QRF range unit
736	SI units only
737	Select only SI specified units
738	Net flo select
739	Select net flow/totalizer
740	Not applicable
741	Phase shift processor
742	Select phase shift processor
743	Not active
744	Active
745	Double Pulse Mode
746	Select double pulse mode on output A/B
747	Quadrature Mode
748	Phase Shift 0°
749	Phase Shift 90°
750	Phase Shift 180°
751	Independent
752	Custody transfer mode
753	Select custody transfer mode
754	OIML
755	NTEP
756	DSP S/W version
757	AAZ comp. treshold
758	Actual density
759	S1 Amplitude
760	S2 Amplitude
761	Frequency
762	Frequency at 20°C
763	Frequ. at 20°C damp
764	Phase difference
765	mrad
766	Sensor simulation
767	Freq. fixed
768	P D fixed
769	BPF
770	72- 96 HzBPF
771	96-120 HzBPF
772	120-144 HzBPF
773	144-168 HzBPF
774	168-192 HzBPF
775	192-216 HzBPF
776	216-240 HzBPF
777	240-264 HzBPF
778	264-288 HzBPF
779	Drive stop
780	Ampl. zero value
781	INZ EEPROM
782	Default
783	All Default
784	Firmware Init
785	Pulse/Freq
786	Pulse rate
787	Pulse setting
788	Pulse rate 2
789	Pulse unit 2
790	Not avail.
791
792	Dummy1
793	Dummy2
794	Dummy Byte1
795	Dummy Byte2
796	Dummy Byte3
797	Dummy Byte4
798	Total vol unit
799	F-Total vol
800	R-Total vol
801	D-Total vol
802	Total mass unit
803	F-Total mass
804	R-Total mass
805	D-Total mass
806	Total energy unit
807	F-Total energy
808	Total net unit
809	F-Total net
810	R-Total net
811	D-Total net
812	Frequency test start
813	Inhibit
814	Apply
815	Frequency index
816	0
817	Temperature
818	Hours elapsed
819	Minutes elapsed
820	Freq. threshold
821	No. mean value
822	No. minute counter
823	QV
824	Status input
825	SI function
826	Format
827	Lowcut
828	alm 1 crit
829	alm 1 sel
830	alm 2 crit
831	alm 2 sel
832	Freq
833	Pls rate
834	Pls unit
835	Pls mode
836	Pls alarm
837	Blank line
838	LoLMT
839	HiLMT
840	Alm
841	Rate
842	Unit
843	Width
844	Mode
845	Alarm
846	Drive Gain
847	Mass Total forw
848	Mass Total rev
849	Vol Total forw
850	Vol Total rev
851	S/N Converter
852	S/N Detector
853	Net flow
854	Net Total forw
855	Net Total rev
856	Conc meas unit
857	Wt-%
858	Conc format
859	Conc meas URV
860	Conc meas LRV
861	Conc alm 1 crit
862	Conc alm 1 select
863	Conc alm 2 crit
864	Conc alm 2 select
865	Conc meas damp
866	Conc meas lowcut
867	Net flo unit
868	Net flo format
869	Net flo URV
870	Net flo LRV
871	Net flo alm 1 crit
872	Net flo alm 1 select
873	Net flo alm 2 crit
874	Net flo alm 2 select
875	Net flo damp
876	Net flo lowcut
877	HART communication
878	Process variables
879	Basic setup
880	Detailed setup
881	Service
882	Service (not open)
883	Service menu part1
884	Service menu part2
885	DSP Reset control
886	Wrt protect menu
887	Self test/Status
888	Status
889	Event Overview
890	Error
891	Warning
892	Self Test
893	Hist Overview ord
894	Hist Overview abs
895	History set menu
896	Hist Overview
897	H.Error
898	H.Alarm
899	H.Warning
900	View fld dev vars
901	View outputs
902	Analog Output 1
903	Analog Output 2
904	Pulse/Status out 1
905	Pulse out A/B
906	Pulse/Status out A/B
907	Pulse/Status out A
908	Pulse/Status out B
909	Pulse/Status out 2
910	No function
911	View input
912	Totalizer
913	Display config
914	Pulse/Status A
915	Pulse/Status B
916	Pulse/Status A/B
917	Pulse out 1
918	Pulse out A
919	Pulse out B
920	Status out 1
921	Status out A/B
922	Status out A
923	Status out B
924	Pulse out 2
925	Status out 2
926	Config fld vars
927	Conc Meas Setup
928	Fixed ref dens menu
929	Ref density setup
930	Temp fix menu
931	Mass flo fix menu
932
933	Energy factor
934	Total reset
935	Slug detection
936	Empty pipe detect
937	Corrosion detect
938	Sensor constants
939	Config out/input
940	Pulse/Status 1
941	Pulse/Status 2
942	Double Pulse A/B
943	Pulse/freq out A
944	Pulse/freq out 1
945	Pulse/freq out A/B
946	Pulse/freq out B
947	Pulse/freq out 2
948	Freq out 1
949	Freq out A/B
950	Freq out A
951	Freq out B
952	Freq out 2
953	HART Output
954	Input/output test
955	Loop trim
956	Device S/W
957	Review device info
958	Review sensor
959	Rev FldDev vars 1
960	Rev FldDev vars 2
961	Rev outputs/input
962	Rev HART
963	Board constants
964	Corr. Table CS30
965	Software
966	Detector Parameter
967	Device Info
968	Frequency Info
969	Concentration meas
970	Concentr Meas Menu
971	Parameter Table
972	H/L Alarm hys
973	Service Measurement
974	Density Calibration
975	Simulation Freq/PD
976	Auto zero check
977	Autozero history
978	Write variables
979	Commands the RCCT_F3 electronics to perform a selftest. Reports any errors that occured.
980	Please refer to manual for complete calibration instructions.
981	Analog Out 1
982	Set the analog output 1 to a fixed value
983	Analog Out 2
984	Set the analog output 2 to a fixed value
985	Trim output 1
986	Trim output 2
987	Pulse Out 1
988	Outputs a user-programmed frequency to the frequency output.
989	Pulse Out A
990	Pulse Out B
991	Pulse Out 2
992	Status Out 1
993	Status Out A
994	Outputs a user-selected level to the status output.
995	Status Out B
996	Status Out 2
997	Status Input
998	Inputs the actual level at the status input.
999	Master reset
1000	All parameter settings are reset to factory settings.
1001	Aborts Auto Zero operation and continues to use previous zero offset value.
1002	Enable wrt 10min
1003	Type the password, if no password defined yet, type all spaces
1004	New password
1005	Aborting
1006	Exiting
1007	Temp LV Adjust
1008	Connect a well-known PT100 termistor to the input.
1009	Temp HV Adjust
1010	LCD/Key Test
1011	Clear History abs
1012	Enter service PW
1013	Password to inhibit any change in parameters without the correct password
1014	Set service PW
1015	Conc Version
1016	Total display
1017	Set tokuchu version
1018	FL20 adjust
1019	KD adjust
1020	Invalid index
1021	Output assignment not possible
1022	Wring index
1023	Max frequency value too high
1024	Max frequency value too low
1025	Pulse duration too long. Select shorter pulse width.
1026	Wrong secondary varcode
1027	Invalid type
1028	Invalid trigger code
1029	Both codes invalid
1030	Invalid transmitter var code
1031	Invalid output 1 varcode
1032	Invalid function
1033	Invalid password
1034	Not in Write Protect Mode
1035	Password accepted
1036	FMU860
1037	DT
1038	DVC
1039	FCX
1040	AS800
1041	340T
1042	340C
1043	344
1044	Siemens Micro K
1045	SITRANS L
1046	SIPAN PH
1047	SITRANS P
1048	75SMT
1049	UNIDELTA
1050	8320
1051	SX5100
1052	TSV175
1053	DMU
1054	3780
1055	BM70
1056	Aborting method due to last error
1057	Device maybe stuck in selftest.
1058	Self test OK
1059	WARN-Loop should be removed from automatic control
1060	Flow must be zero Perform calibration?
1061	A problem was detected
1062	Abort;Fix and Retry
1063	NOTE-Loop may be returned to automatic control
1064	Autozero in progress.
1065	Enter Date of Auto-zeroing. (mm/dd/yyyy)
1066	Choose frequency output level
1067	1 kHz;Other;End
1068	Output
1069	Aborting due to field device error
1070	Frequency output 1 is fixed at %0 Hz
1071	Frequency output A is fixed at %0 Hz
1072	Frequency output B is fixed at %0 Hz
1073	Frequency output 2 is fixed at %0 Hz
1074	Choose status output level
1075	OFF;ON ;End
1076	Status output 1 is fixed at %0
1077	Status output B is fixed at %0
1078	Status output 2 is fixed at %0
1079	Read status level
1080	Read;End
1081	Status input is fixed at %0
1082	About to Perform Master Reset
1083	Performing Master Reset...
1084	Master Reset Done
1085	No Device Info On Master Reset
1086	Enter current password to enable to write for 10 minutes:
1087	Released the write protection for 10 minutes.
1088	If you wish to release completely, you have to change password to all of spaces.
1089	Enter new password to change state of write protect:
1090	Re-enter new password within 30 seconds:
1091	Changed to new password.
1092	It changed the state of protection related password.
1093	Adjust temperature sensor at 0°C
1094	Not Apply;Apply
1095	T0 adjusted with %0 Ohm
1096	Adjust temperature sensor at 100°C
1097	T100 adjusted with %0 Ohm
1098	Perform LCD/Key Test
1099	Exit;Start LCD;Start Keys
1100	LCD/Key Test in progress
1101	Clear history absolute
1102	Enter Date of clearing the absolute history.(mm/dd/yyyy)
1103	About to read out the ordered Error list.
1104	Error:%0%1
1105	Alarm:%0%1
1106	Warning:%0%1
1107	Input password
1108	Service Menu is %0
1109	Enter version number
1110	Concentration Version: C%0
1111	Tokuchu version
Reference ID	String