Device dictionary

Loading…

Reference ID	String
0	Chg power on info- Change the information displayed when turn on the power.
1	Chg power on info
2	Abort of the Chg power on info- Display the power on information.
3	Abort of the Chg power on info
4	Chg universal rev- Change the universal command revision.
5	Chg universal rev
6	Abort of the Chg universal rev- Display the universal revision.
7	Abort of the Chg universal rev
8	Not Write Protected
9	Write Protected
10	EJA-NEXT
11	P sensor error
12	CT sensor error
13	Cap EEPROM error
14	AT sensor error
15	Amp EEPROM error
16	CPU board error
17	No device ID
18	P outside limit
19	SP outside limit
20	CT outside limit
21	AT outside limit
22	P over range
23	SP over range
24	P high alarm
25	P low alarm
26	SP high alarm
27	SP low alarm
28	CT high alarm
29	CT low alarm
30	Illegal P LRV
31	Illegal P URV
32	Illegal P SPAN
33	P SPAN trim err
34	P ZERO trim err
35	Illegal SP LRV
36	Illegal SP URV
37	Illegal SP SPAN
38	Status group 7
39	SP SPAN trim err
40	SP ZERO trim err
41	SC config error
42	Status group 8
43	FT high alarm
44	FT low alarm
45	ILBD over range
46	Invalid Ref DP
47	Invalid Ref SPL
48	Invalid Ref SPH
49	Invalid Ref F
50	Status group 9
51	B Blocking
52	H Side Blocking
53	L Side Blocking
54	Large Fluct H
55	Large Fluct L
56	A Blocking
57	inH2O @68degF
58	ftH2O @68degF
59	mmH2O @68degF
60	g/cm2
61	kg/cm2
62	ftH2O
63	Feet of Water at 4 Degrees Celsius
64	hPa
65	Hectopascals
66	.3f
67	.4f
68	.1f
69	.2f
70	.5f
71	.0f
72	.6f
73	Pres %
74	Pres Damp
75	6.2f
76	Si Oil
77	F Oil
78	Process Conn type
79	Thread
80	Num of RS
81	Two Seals
82	Extension
83	HTV-W
84	HTV-E
85	P LTP
86	P UTP
87	AO alm typ
88	Process Conn matl
89	Module type
90	DP
91	Pressure
92	Excess Correction Attemped
93	Not write protect mode
94	The First Password Accepted
95	Keypad input
96	Pres trim info.
97	SP sensor trim
98	SP trim info.
99	Trim info.
100	Diag Parameters
101	ILBD Parameters
102	Status
103	Diag Variables
104	Diag Reference
105	Fluct Variables
106	Test
107	Configuration
108	Diag Lim
109	Diag Ref Lim
110	HT Parameters
111	Flg Temp Lim
112	Diag Output
113	Error log
114	SP Range
115	SP A/G Setup
116	SP sensor
117	Temp sensor
118	T.Z. Cmp menu
119	S.C. menu
120	Process Alerts
121	Config Pres Alerts
122	Config Temp Alerts
123	DO Config
124	Display condition
125	Disp select
126	P disp condition
127	SP disp condition
128	Engr disp range
129	Wrt protect menu
130	Pres sensor trim
131	Self Test- Commands the EJX electronics to perform a selftest. Reports any errors that occured.
132
133	Clear digital to analog trim- Resets the trim adjustment to the initial calibrated values that were set at factory.
134	Clear D/A trim
135	Pressure trim- Executes full sensor trim with zero point adjustment by Lower Pt and span adjustment by Upper Pt.
136	Pres trim
137	Clear pressure sensor trim- Resets the trim adjustment to the initial calibrated values that were set at factory.
138	Clear P snsr trim
139	Static pressure trim- Executes full sensor trim with zero point adjustment by Lower Pt and span adjustment by Upper Pt.
140	Static Pres trim
141	Clear static pressure sensor trim- Resets the trim adjustment to the initial calibrated values that were set at factory.
142	Clear SP snsr trim
143	Error log clear- Clears the error records.
144	Error log Clear
145	SP Apply values
146	Signal characterizer point setting- Sets the coordinates of break points to characterize the values in percent of the output.
147	Point setting
148	Digital output test- Allows the user to test the contact output for a digital signal at the contact output terminal of the device. Select 'On' to output the digital signal.
149	DO Test
150	Modify engineering unit- Modifies the engineering unit or sets a customized engineering unit. Enter a series of up to eight alphanumeric characters, spaces, or slashes (only first six characters are shown on LCD). Note that if you already select the unit at 'Set Engineering Unit,' the unit appears as a default. Then re-enter the unit but enter a space instead of a character to display the character in lowercase on LCD. For example, in order to show 'aBCd' on LCD, enter 'ABCD' first, then enter '_BC_'.
151	Modify Engr Unit
152	Test Key
153	Enable parameter change for 10 min.- releases the software write protection for 10 minutes when the password is entered.
154	Enable wrt 10min
155	New password- Sets or changes the password for software write protection.
156	New password
157	Aborting
158	Exiting
159	Set Diag Mode
160	Pres Zero trim
161	Error log view- Displays the error records from log1(latest) to log4.
162	Error log view
163	Set engineering unit- Selects the engineering unit from the list.
164	Set Engr Unit
165	Static Pressure- Pressure of the process measured with respect to the reference pressure equal to 0.
166	SP
167	Static pressure percent of range- Static Pressure Variable that tracks the Digital Value representation with respect to the range defined by the Lower Range Value and Upper Range Value, for normal operating modes. The units of this variable are always in percent.
168	SP %
169	Sensor temperature- Temperature measured at sensor capsule.
170	Engineer Unit Select Code for Easy Setting
171	psia
172	mmHgA
173	mmAq
174	mmWG
175	Torr
176	inHgA
177	gf/cm2
178	kgf/cm2
179	kg/cm2G
180	kg/cm2A
181	t/h
182	m3/h
183	m3/min
184	l/h
185	l/min
186	kl/h
187	kl/min
188	Nl/h
189	Nl/min
190	Nm3/h
191	Nm3/min
192	ACFH
193	ACFM
194	SCFH
195	SCFM
196	GPH
197	GPM
198	kg/m3
199	g/cm3
200	Engineering display- Process variable displayed in user scale and unit.
201	Engr Disp
202	Engineering display exponents- Exponents for user scale display.
203	Engr exp
204	x1
205	x10
206	x100
207	x1000
208	Engineering unit- Engineering unit for user scale display.
209	Engr Unit
210	Lower pressure trim deviation- Deviation from the original value.
211	P LTD
212	Upper pressure trim deviation- Deviation from the original value.
213	P UTD
214	Lower static pressure trim point- Applied static pressure at which the last lower static pressure trim was performed.
215	SP LTP
216	Upper static pressure trim point- Applied static pressure at which the last upper static pressure trim was performed.
217	SP UTP
218	Lower static pressure trim deviation- Deviation from the original value.
219	SP LTD
220	Upper static pressure trim deviation- Deviation from the original value.
221	SP UTD
222	Trim information- Text that is associated with the trim information. This text can be used by the user in any way. A recommended use is to record who to trim the device.
223	Trim Who
224	Trim information- Text that is associated with the trim information. This text can be used by the user in any way. A recommended use is to record when the latest trim is done for the device.
225	Trim Date
226	Trim information- Text that is associated with the trim information. This text can be used by the user in any way. A recommended use is to record where the latest trim is done for the device.
227	Trim Loc
228	Trim information- Text that is associated with the trim information. This text can be used by the user in any way, and there is no recommended use.
229	Trim Desc
230	Low cut- Sets the range in vicinity of 0% within which the low cut function is activated according to the selected low cut mode.
231	Low cut
232	5.2f
233	Low cut mode- Selects the type of the low cut function to be used; LINEAR or ZERO.
234	Low cut mode
235	High/Low swap- Reverses the high pressure side and low pressure side of the transmitter. For example, use this function when assigning the high pressure impulse line connection to the L side of the transmitter.
236	H/L Swap
237	Static Pressure Lower Range Value- Defines the operational endpoint from which the 0% point of the Percent Range are derived.
238	SP LRV
239	Static Pressure Upper Range Value- Defines the operational endpoint from which the 100% point of the Percent Range are derived.
240	SP URV
241	Static Pressure Variable Unit- Engineering unit to be displayed with the Digital Value representation, Minimum Span, Upper Range Value, Lower Range Value, Lower Sensor Limit, and Upper Sensor Limit for the Static Pressure.
242	SP Unit
243	Absolute/gauge selection- Type of Static pressure variable.
244	A/G Select
245	Gauge
246	Absolute
247	Atmospheric Pressure Value- Sets the coefficient value used for the conversion of the measured absolute pressure value into gauge pressure value.
248	Atm. Pres Value
249	Static Pressure High/Low Select- Measuring point of the static pressure; high pressure side or low pressure side.
250	SP H/L Select
251	Amp Temperature
252	Amp temp
253	Field Device Variable Unit- Digital unit that the variable will be displayed with. Sensor Temperature- Temperature associated with the sensor that is responsible for a process measurement.
254	Temp Unit
255	Bi-directional flow measurement setup- Enables/disables bi-directional flow measurement mode. In this mode, when the pressure equivalent to 0% is applied, the device outputs 50%. Applicable only for differential pressure transmitters.
256	Bi-dir mode
257	Normal Mode
258	Bi-Direction Mode
259	Quick response- Enables/disables to set the damping value less than 0.5 sec.
260	Quick resp
261	Temperature Zero compensation mode- Enables/disables temperature zero compensation.
262	T.Z. Cmp mode
263	Temperature Zero shift compensation- Defines the value to be used for temperature zero shift compensation.
264	Temp Zero
265	%/degC
266	7.3f
267	Signal characterizer- Enables/disables signal characterizer function.
268	S.C.
269	Disabled
270	Enabled
271	Number of break points- Sets the number of points for signal characterizer.
272	Num of points
273	2u
274	Displays the start point of X.
275	X Start
276	Displays the start point of Y.
277	Y Start
278	Displays the end point of X.
279	X End
280	Displays the end point of Y.
281	Y End
282	Status of digital output- Displays the current status of digital output.
283	Digital Output
284	Automatic recover- Defines if the device automatically returns to normal operation without restarting or not, once after it recovers from the sensor error status.
285	Auto recover
286	Analog output lower limit- Sets the lower limit value for analog output.
287	AO lower limit
288	Analog output upper limit- Sets the upper limit value for analog output.
289	AO upper limit
290	Selects alert mode for pressure alarm.
291	Pres Alert mode
292	Hi. Al Detect
293	Lo. Al Detect
294	Hi/Lo. Al Detect
295	Sets threshold value for pressure high alarm.
296	Hi Alert Val
297	Sets threshold value for pressure low alarm.
298	Lo Alert Val
299	Selects alert mode for static pressure alarm.
300	SP Alert mode
301	Selects alert mode for sensor temperature alarm.
302	Temp Alert mode
303	Bar indicator- Defines to show/hide bar indicator on LCD.
304	Bar Indicator
305	Sets threshold value for static pressure high alarm.
306	SP Hi Alert Val
307	Sets threshold value for static pressure low alarm.
308	SP Lo Alert Val
309	Sets threshold value for sensor temperature high alarm.
310	Temp Hi Alert Val
311	4.0f
312	Sets threshold value for sensor temperature low alarm.
313	Temp Lo Alert Val
314	DO selection- Select alarm(s) whose status should be output via digital output.
315	DO Select
316	Pres/SP
317	Pres/Temp
318	SP/Temp
319	Pres/SP/Temp
320	Diag Alarm
321	All
322	DO signal type- Defines the action of digital output when the alarm is detected.
323	DO Signal type
324	ON WHEN AL. DETECT
325	OFF WHEN AL. DETECT
326	LCD output1- Defines the variable to be shown on LCD.
327	Disp Out1
328	PRES
329	PRES %
330	ENGR. PRES
331	LCD output2- Defines the variable to be shown on LCD.
332	Disp Out2
333	LCD output3- Defines the variable to be shown on LCD.
334	Disp Out3
335	LCD output4- Defines the variable to be shown on LCD.
336	Disp Out4
337	Display pressure % function- Defines the display mode for pressure variable in %; Linear or Squareroot.
338	Disp Pres % fnctn
339	Display pressure % resolution- Defines the display resolution level for pressure variable in %; normal or high resolution.
340	Disp Pres % Reso
341	High Resolution
342	Pressure display decimal position- Defines the decimal point position for the pressure variable display.
343	Pres disp point
344	0
345	1
346	2
347	3
348	4
349	Static pressure display decimal point position- Defines the decimal point position for the static pressure variable display.
350	SP disp point
351	Engineering display lower range value- Sets the lower range value equivalent to 0% for user scale display.
352	Engr LRV
353	Engineering display upper range value- Sets the upper range value equivalent to 100% for user scale display.
354	Engr URV
355	Engineering display decimal position- Defines the decimal point position for user scale display.
356	Engr point
357	Model 1- Model and Suffix codes of the device.
358	Model 1
359	Model 2- Part of the Model and suffix codes of the device, which follows the codes shown in Model 1.
360	Model 2
361	Model 3- Part of the Model and suffix codes of the device, which follows the codes shown in Model 2.
362	Model 3
363	Style code- Displays the style code of the device.
364	Style No.
365	Serial number- Displays the serial number of the device.
366	Serial No.
367	Manufacturing date- Displays the date of manufacturing the device.
368	Mftr Date
369	Extra number- Reference number for special customization.
370	Extra No.
371	External zero-adjustment permission- Enables/disables external zero adjustment.
372	Ext SW
373	Software rev
374	Gasket Material- Construction material of a seal that exists between the module and flange.
375	Gasket matl
376	Process Connector Size- Hardware adjacent to the sensor, that physically connects the process to the sensor.
377	Process Conn size
378	ANSI3, C150
379	ANSI3, C300
380	ANSI3, C600
381	ANSI4, C150
382	ANSI4, C300
383	ANSI2, C150
384	ANSI2, C300
385	ANSI2, C600
386	DIN80, PN10/16
387	DIN80, PN25/40
388	DIN80, PN64
389	DIN100, PN10/16
390	DIN100, PN25/40
391	DIN50, PN10/16
392	DIN50, PN25/40
393	DIN50, PN64
394	ANSI 150
395	ANSI 300
396	ANSI 600
397	DIN 10/16
398	DIN 25
399	DIN 40
400	1/2NPT Female
401	1/4NPT Female
402	Rc 1/2 Female
403	1/2NPT Male
404	G 1/2 Male
405	M2O * 1.5 Male
406	R 1/2 Male
407	Remote Seal Fill Fluid- Fluid material in the device remote seal.
408	Silicone
409	SH704
410	SH705
411	Ethy Gly/H2O
412	Prop Gly/H2O
413	Software seal- Displays whether or not a master password was used (Break).
414	Software seal
415	Break
416	Keep
417	SI Option
418	OFF
419	ON
420	Pressure Sensor Range Code
421	P Range code
422	M
423	H
424	L
425	A
426	B
427	C
428	E
429	V
430	D
431	Static Pressure Sensor Range Code
432	SP Range code
433	Standard
434	Pressure Value or % Value for Trim
435	Pres for trim
436	Static Pressure Value or % Value for Trim
437	SP for trim
438	Engineer Unit of Capital Letter
439	Small Character of Engineer Unit
440	X1 Value
441	X1
442	Y1 Value
443	Y1
444	X2 Value
445	X2
446	Y2 Value
447	Y2
448	X3 Value
449	X3
450	Y3 Value
451	Y3
452	X4 Value
453	X4
454	Y4 Value
455	Y4
456	X5 Value
457	X5
458	Y5 Value
459	Y5
460	X6 Value
461	X6
462	Y6 Value
463	Y6
464	X7 Value
465	X7
466	Y7 Value
467	Y7
468	X8 Value
469	X8
470	Y8 Value
471	Y8
472	X9 Value
473	X9
474	Y9 Value
475	Y9
476	Pressure Trim Mode Selection Code
477	Auto, Lower Pt
478	Auto, Upper Pt
479	Manual, Lower Pt
480	Manual, Upper Pt
481	Pressure Trim Point or Deviation
482	Static Pressure Trim Mode Selection Code
483	Static Pressure Trim Point or Deviation
484	Trim Clear Code
485	Not Clear
486	ALL
487	Keyword for Test Mode
488	Data No. for Test
489	Data1 for Test
490	Data2 for Test
491	04X
492	08X
493	Error Record Selection Code
494	Log1
495	Latest
496	Log2
497	Log3
498	Log4
499	Oldest
500	Error Record 0
501	Error Rec 0
502	2X
503	Error Record 1
504	Error Rec 1
505	Error Record 2
506	Error Rec 2
507	Error Record 3
508	Error Rec 3
509	Error Record 4
510	Error Rec 4
511	Error Record 5
512	Error Rec 5
513	Error Record 6
514	Error Rec 6
515	Error Record 7
516	Error Rec 7
517	Data Selection Code
518	Value 1
519	VALUE 1
520	Value 2
521	VALUE 2
522	Digital Output Test Code
523	Exit DO Test mode
524	Space for 8 characters
525	Diag Error Status.
526	Diag Error
527	Bit mask for Alarm against Diag Error Status.
528	Diag Option
529	Diag Mode.
530	Diag Mode
531	Stop
532	Calculation
533	Reference
534	Diag Applicable.
535	Diag Applicable
536	Ratio of Root fluct DP for Reference with Compensation Status.
537	Ratio fDP Status
538	Sensor Failure
539	Device Failure
540	Uncertain
541	Invalid Ref
542	Good
543	Ratio of Root fluct DP for Reference.
544	Ratio fDP
545	Ratio of Root fluct SP low side for Reference Status.
546	Ratio fSPl Status
547	Ratio of Root fluct SP low side for Reference.
548	Ratio fSPl
549	Ratio of Root fluct SP high side for Reference Status.
550	Ratio fSPh Status
551	Ratio of Root fluct SP high side for Reference.
552	Ratio fSPh
553	Blocking Factor Status.
554	BlkF Status
555	Blocking Factor.
556	BlkF
557	DPAvg Status.
558	DPAvg Status
559	DPAvg.
560	DPAvg
561	Compensated Ratio of Root fluct DP for Reference Status.
562	CRatio fDP Status
563	Compensated Ratio of Root fluct DP for Reference.
564	CRatio fDP
565	Non-Compensated Ratio of Root fluct DP for Reference Status.
566	NRatio fDP Status
567	Non-Compensated Ratio of Root fluct DP for Reference.
568	NRatio fDP
569	fluct DP Status.
570	fDP Status
571	fluct DP.
572	fDP
573	12g
574	.5e
575	fluct SP low side Status.
576	fSPl Status
577	fluct SP low side.
578	fSPl
579	fluct SP high side Status.
580	fSPh Status
581	fluct SP high side.
582	fSPh
583	Test 1
584	Test 2
585	Test 3
586	Test 4
587	Diag Period.
588	Diag Period
589	Diag Limit fluct DP max.
590	Lim fDPmax
591	Diag Limit fluct DP min.
592	Lim fDPmin
593	Diag Limit fluct SP low side max.
594	Lim fSPlmax
595	Diag Limit fluct SP low side min.
596	Lim fSPlmin
597	Diag Limit fluct SP high side max.
598	Lim fSPhmax
599	Diag Limit fluct SP high side min.
600	Lim fSPhmin
601	Diag Limit Blocking Factor max.
602	Lim BlkFmax
603	Diag Limit Blocking Factor min.
604	Lim BlkFmin
605	Diag Limit DPAvg max.
606	Lim DPAvgmax
607	5.5f
608	Diag Limit DPAvg min.
609	Lim DPAvgmin
610	Diag Alarm Suppression Count.
611	Diag Supp Count
612	.0d
613	Diag Description.
614	Diag Description
615	Reference fluct DP Status.
616	Ref fDP Status
617	Reference fluct DP.
618	Ref fDP
619	10g
620	.3e
621	Reference fluct SP low side Status.
622	Ref fSPl Status
623	Reference fluct SP low side.
624	Ref fSPl
625	Reference fluct SP high side Status.
626	Ref fSPh Status
627	Reference fluct SP high side.
628	Ref fSPh
629	Reference Blocking Factor Status.
630	Ref BlkF Status
631	Reference Blocking Factor.
632	Ref BlkF
633	10.6f
634	Reference DPAvg Status.
635	Ref DPAvg Status
636	Reference DPAvg.
637	Ref DPAvg
638	Reference Limit fluct DP min.
639	Ref Lim fDPmin
640	Reference Limit fluct SP min.
641	Ref Lim fSPmin
642	Reference Limit Blocking Factor max.
643	Ref Lim BlkFmax
644	Flow Compensation for Ratio of Root fluct DP.
645	Diag DPComp
646	Compensation
647	Non-Compensation
648	Flg temp.
649	Flg temp
650	Flg temp Coef.
651	Flg temp Coef
652	Flg temp Hi Alert Val.
653	Flg temp Hi Alert Val
654	Flg temp Lo Alert Val.
655	Flg temp Lo Alert Val
656	Diag Analog Output Option.
657	Diag Out Option
658	Off
659	Burnout
660	Fall back
661	Diag Fixed Analog Output Value.
662	Diag Fixed Out Val
663	Function control
664	Lowercase conversion not succeeded.
665	Analog output trim
666	SP setup
667	Config SP Alerts
668	Additional Info
669	Write variables
670	Re-range
671	Master Reset- Commands the EJX electronics to reset and perform a selftest. Reports any errors that occured.
672	Static Pressure Lower Sensor Limit Value- Defines the minimum usable value for the Lower Range Value for the static pressure.
673	SP LSL
674	Static Pressure Upper Sensor Limit Value- Defines the maximum usable value for the Upper Range Value for the static pressure.
675	SP USL
676	Static Pressure Minimum Span- Defines the minimum usable span for the static pressure.
677	SP Min Span
678	Static Pressure Damping Value- Damping time constant applied to both the Digital Value representation for static pressure. The units of this variable are always in seconds.
679	SP Damp
680	Error Record 8
681	Error Rec 8
682	Sensor Temperature- Temperature at the sensor that is responsible for a process measurement.
683	temperature_digital_units_help
684	temperature_digital_value_help
685	Static Pres
686	Loop Warning Variables
687	Displays a warning message before new values are sent.
688	Primary Variable- Primary variable associated with the process Secondary Variable- secondary variable associated with the process. Tertiary Variable- tertiary variable associated with the process.
689	Test Auto Release Time
690	10 min
691	30 min
692	60 min
693	3 hour
694	6 hour
695	12 hour
696	FMU860
697	DT
698	DVC
699	FCX
700	AS800
701	340T
702	340C
703	344
704	Siemens Micro K
705	SITRANS L
706	SIPAN PH
707	SITRANS P
708	75SMT
709	UNIDELTA
710	8320
711	SX5100
712	TSV175
713	DMU
714	3780
715	BM70
716	8u
717	low
718	high
719	tmp_av
720	.3g
721	.f
722	%
723	3.2f
724	s
725	4.2f
726	5.3f
727	6.4f
728	This function is not supported.
729	In write protect mode.
730	Current power on informatin is ON. Select status
731	OFF;ON
732	Current power on informatin is OFF. Select status
733	Power on info is changed to ON.
734	Power on info is changed to OFF.
735	Current power on informatin is ON.
736	Current power on informatin is OFF.
737	Confirm that the configuration tool supports new universal rev. After the universal rev is changed, the following operations are required. 1 Exit the configuration tool. 2 Power OFF and ON the device. 3 Restart the configuration tool.
738	Current universal rev is %{universal_revision} with fld dev rev %{transmitter_revision}. New universal rev is %{next_universal_rev} with fld dev rev %{next_device_rev}. Are you sure to change the universal rev?
739	Current universal rev is %{universal_revision} with fld dev rev %{transmitter_revision}. Are you sure to change the universal rev?
740	Universal rev %{test_key_4_upper1} is not supported!
741	Enter new rev number. 5: universal rev 5 7: universal rev 7
742	Number is invalid.
743	Current universal rev is %{0}. Universal rev is not changed.
744	Current universal rev is %{universal_revision} with fld dev rev %{transmitter_revision}. Are you sure to stay with current universal rev?
745	New rev is applied only after power OFF and ON the device. Are you sure to change the universal rev from %{universal_revision} to %{object_universal_rev}?
746	Setting in progress, please wait for several seconds.
747	Process incompleted.
748	To complete the change of universal rev: 1 Exit the configuration tool. 2 Power OFF and ON the device. 3 Restart the configuration tool.
749	Process completed.
750	Current universal rev is %{universal_revision} with fld dev rev %{transmitter_revision}. New universal rev will be %{next_universal_rev} with fld dev rev %{next_device_rev}.
751	Current universal rev is %{universal_revision} with fld dev rev %{transmitter_revision}.
752	Self test in progress please wait
753	Device maybe stuck in selftest.
754	Device maybe stuck in master reset.
755	Master Reset OK
756	D/A trim data is cleared.
757	Select trim mode
758	Off;Auto, Lower Pt;Auto, Upper Pt;Manual, Lower Pt;Manual, Upper Pt
759	Pres for trim %{0} %{1}
760	tmp
761	Pres sensor trim data is cleared.
762	SP for trim %{0} %{1}
763	SP sensor trim data is cleared.
764	Execute OK ?
765	Exit;Execute
766	Performing log clear
767	0%;100%;Exit
768	Apply new 0% input
769	Current applied process value: %{static_pressure_value} %{static_pressure_units}
770	Set as 0% value;Read new value;Leave as found
771	Apply new 100% input
772	Set as 100% value;Read new value;Leave as found
773	Select one
774	List;Edit all points;Edit one point;Exit
775	List X1 %[6.2f]{0}% Y1 %[6.2f]{1}% X2 %[6.2f]{2}% Y2 %[6.2f]{3}% X3 %[6.2f]{4}% Y3 %[6.2f]{5}%
776	List X4 %[6.2f]{6}% Y4 %[6.2f]{7}% X5 %[6.2f]{8}% Y5 %[6.2f]{9}% X6 %[6.2f]{10}% Y6 %[6.2f]{11}%
777	List X7 %[6.2f]{12}% Y7 %[6.2f]{13}% X8 %[6.2f]{14}% Y8 %[6.2f]{15}% X9 %[6.2f]{16}% Y9 %[6.2f]{17}%
778	Num of points is 0.
779	It will set S.C. to be disabled, OK?
780	No;Yes
781	Set S.C. to be disabled...
782	Specify S.C. point to set value
783	choice
784	Off;On;Exit
785	Digital Output is fixed to %{0}
786	Enter Engr Unit:
787	Enter a space for the character to display it in lowercase:
788	Select case:
789	Write;Read;Coefs Clear;End
790	Test Key 1
791	Test Key 2
792	Select one:
793	Test Key 3;Test Key 4
794	Test Key 3
795	Test Key 4
796	Test Key 3 %{0}
797	Test Key 4 %{0}%{1} %{2}
798	Now Clearing!
799	Enter current password to enable to write for 10 minutes:
800	Released the write protection for 10 minutes.
801	If you wish to release completely, you have to change password to all of spaces.
802	Enter new password to change state of write protect:
803	Re-enter new password within 30 seconds:
804	Aborting method due to last error
805	Changed to new password.
806	It changed the state of protection related password.
807	Current Diag Mode is : %{diag_mode} Select Diag Mode
808	Stop;Calculation;Reference
809	Show the:
810	Log1(Latest);Log2;Log3;Log4(Oldest);Exit
811	Advanced Diag Fail.
812	Simulation mode
813	No error
814	Select unit
815	;kPa;MPa;mbar;bar;psi;psia;mmH2O;mmHg;mmHgA;mmAq;mmWG;Torr;inH2O;inHg;inHgA;ftH2O;gf/cm2;kgf/cm2;kg/cm2G;kg/cm2A;atm;kg/h;t/h;m3/h;m3/min;l/h;l/min;kl/h;kl/min;Nl/h;Nl/min;Nm3/h;Nm3/min;ACFH;ACFM;SCFH;SCFM;GPH;GPM;m;mm;in;ft;kg/m3;g/cm3
816	;kPa;MPa;mbar;bar;atm;kg/h;t/h;m3/h;m3/min;l/h;l/min;kl/h;kl/min;Nl/h;Nl/min;Nm3/h;Nm3/min;m;mm;kg/m3;g/cm3
817	It will reset the master CPU, OK ?
818	Master Reset in progress please wait
819	Self Test OK
Reference ID	String