Device dictionary

Loading…

Reference ID	String
0	WIKA
1	UniTrans
2	extend. status 1
3	E07 sensor comm
4	E07 communikation sensor
5	E02 EE checksum
6	E02 EEPROM checksum
7	E03 EE general
8	E03 EEPROM general
9	E01 power supply
10	E01 power supply
11	E04 Temp. limits
12	E04 Temperature out of limits
13	extend. status 2
14	E00 ROM Error
15	E06 sens detect.
16	E06 sensor detection
17	Pressure
18	Temp
19	Comm status
20	Device status
21	Extended status
22	Process data
23	Sensor data
24	Range limits
25	Calibrate range
26	Cal. with pressure
27	Cal. without press.
28	Output
29	Evaluation
30	Service
31	Run time counters
32	Extreme values
33	.3f
34	Temperature value
35	.1f
36	Temperature unit
37	7d
38	.2f
39	Linear
40	Table
41	Dummy for cmd 168/146
42	Dummy for cmd 15
43	.0f
44	4.0f
45	Output invert
46	Mode of output: Non-inverted or inverted
47	Not inverted
48	Inverted
49	Alarm scale mode
50	Mode of Alarm: Alarm on output current too high (upscale) resp. too low (downscale)
51	Upscale (21mA)
52	Downscale (3,6mA)
53	Current limits
54	Standard or extended current limits
55	3,8-20,5mA
56	4-20mA
57	8.2f
58	Password
59	Password, necessary then writing of parameters is locked
60	4d
61	Density
62	Density; used to calculate e.g. fluid level of tanks from pressure
63	8.1f
64	Lin table index
65	Index of linearisation table entry
66	h% value
67	Height percent value
68	V% value
69	Volume percent value
70	mA
71	Total runtime
72	Total runtime
73	Time since reset
74	Runtime since last factory reset
75	Time since calibr.
76	Runtime since last calibration
77	Sensor runtime
78	Runtime of sensor
79	press max
80	Maximal pressure occured since last extreme values reset
81	press min
82	Minimal pressure occured since last extreme values reset
83	temp max
84	Maximal temperature occured since last extreme values reset
85	temp min
86	Minimal temperature occured since last extreme values reset
87	Unit of min/max pressure
88	Unit of min/max temperature
89	Dummy cmd130
90	Selections for reset extr val
91	Work index for reset of extreme values reset
92	max pressure
93	min pressure
94	max temperature
95	min temperature
96	Max. table index
97	Number of maximal linearisation table entries
98	Actual table index
99	Number of actual linearisation table entries
100	sw revision Byte0
101	Less important value Byte of SW Revision
102	02d
103	sw revision Byte1
104	Most important value Byte of SW Revision
105	Type code
106	Type code
107	serial number 0
108	serial number 1
109	serial number 2
110	serial number 3
111	serial number 4
112	serial number 5
113	serial number 6
114	serial number 7
115	serial number 8
116	serial number 9
117	serial number 10
118	serial number 11
119	serial number 12
120	serial number 13
121	Reset changed flag
122	Set zero (LRV)
123	Set span end (URV)
124	Read lin. table
125	Write lin. table
126	Write password
127	Factory reset
128	Reset runtime counter
129	Reset extreme vals
130	Read SW revision
131	Read type code
132	Read internal num.
133	FMU860
134	DT
135	DVC
136	FCX
137	AS800
138	340T
139	340C
140	344
141	Siemens Micro K
142	SITRANS L
143	SIPAN PH
144	SITRANS P
145	75SMT
146	UNIDELTA
147	8320
148	SX5100
149	TSV175
150	DMU
151	3780
152	BM70
153	8u
154	Reset changed flag ?
155	OK
156	Set actual pressure value as zero point (=lower range value)?
157	Set zero point: OK
158	Reread of zero point: OK
159	Set actual pressure value as span endpoint (=upper range value)?
160	Set of span end: OK
161	Reread of span end: OK
162	Index
163	Index: %{0} h: %{Local_lin_table_h_value} V: %{Local_lin_table_V_value}
164	Write lin table: Index:
165	h%-Value:
166	Local_lin_table_h_value
167	V%-Value
168	Local_lin_table_V_value
169	Please enter password between 0-9999 (dez)
170	iWork
171	Value was not in the range described; please enter again
172	Do you really want to send this Password?
173	Reread of write protect: OK
174	Do you really want to reset the device to factory settings?
175	Do you really want to reset the runtime counter?
176	Reset of runtime counter: OK
177	Reread of runtime counter: OK
178	Select value to reset
179	Electronic SW revision: %{1}.%{0}
180	Type code: %{0}
Reference ID	String