| 0 |
|
| 1 |
|
| 2 |
Serial number |
| 3 |
Figure |
| 4 |
Figure: Status signals |
| 5 |
DD version |
| 6 |
1.02.01-00 |
| 7 |
Device name |
| 8 |
VEGAPULS C 20 |
| 9 |
Device-Revision |
| 10 |
Compatibility information for integration into the device catalogue |
| 11 |
Measurement loop name |
| 12 |
Name of the measurement loop |
| 13 |
Sensor |
| 14 |
Expanded Device Type |
| 15 |
Identification of the instrument type through Fieldbus |
| 16 |
x |
| 17 |
Bustype ID |
| 18 |
DTM ID |
| 19 |
Manufacturer ID |
| 20 |
Sensor type |
| 21 |
SIL qualified sensor |
| 22 |
No |
| 23 |
Yes |
| 24 |
Distance unit of the instrument |
| 25 |
Selection of the physical distance unit for indication and parameter adjustment |
| 26 |
mm |
| 27 |
m |
| 28 |
in |
| 29 |
ft |
| 30 |
Temperature unit of the instrument |
| 31 |
Selection of the physical temperature unit for indication and parameter adjustment |
| 32 |
°C |
| 33 |
K |
| 34 |
°F |
| 35 |
Limitation measuring range begin |
| 36 |
.2f |
| 37 |
.1f |
| 38 |
.0f |
| 39 |
.3f |
| 40 |
Limitation measuring range begin active |
| 41 |
Certainty at vessel bottom or measuring range end |
| 42 |
Additional factor safety at the measuring range end |
| 43 |
% |
| 44 |
Correction of propagation velocity |
| 45 |
Averaging factor on decreasing amplitude |
| 46 |
d |
| 47 |
Averaging factor on increasing amplitude |
| 48 |
'Smooth raw value curve' active |
| 49 |
Offset detection curve |
| 50 |
dB |
| 51 |
Width focusing range |
| 52 |
Minimum measurement reliability |
| 53 |
Minimum measurement reliability outside the focussing range |
| 54 |
Time for opening of the focus range |
| 55 |
s |
| 56 |
Safety of the false signal suppression |
| 57 |
Function 'Combine echoes' |
| 58 |
Deactivated |
| 59 |
Only bottom section |
| 60 |
Complete measuring range |
| 61 |
Amplitude difference 'Combine echoes' |
| 62 |
Position difference 'Combine echoes' |
| 63 |
'First large echo' active |
| 64 |
Amplitude threshold 'First large echo' |
| 65 |
Delay of fault signal |
| 66 |
Behaviour in case of loss of echo |
| 67 |
Last valid measured value |
| 68 |
Failure message |
| 69 |
Maintenance message |
| 70 |
Measured value offset |
| 71 |
.4f |
| 72 |
Activity to be carried out |
| 73 |
Restore delivery status |
| 74 |
Restore basic settings |
| 75 |
Scaling format |
| 76 |
Determination of the presentation of decimal points |
| 77 |
##### |
| 78 |
####.# |
| 79 |
###.## |
| 80 |
##.### |
| 81 |
#.#### |
| 82 |
100 % corresponds to |
| 83 |
Scaled value for 100 % |
| 84 |
0 % corresponds to |
| 85 |
Scaled value for 0 % |
| 86 |
Scaling unit |
| 87 |
Measuring unit for the scaled value |
| 88 |
- |
| 89 |
mA |
| 90 |
kg |
| 91 |
t |
| 92 |
g |
| 93 |
l |
| 94 |
m³ |
| 95 |
cm |
| 96 |
mbar |
| 97 |
bar |
| 98 |
Pa |
| 99 |
kPa |
| 100 |
MPa |
| 101 |
l/s |
| 102 |
l/min |
| 103 |
l/h |
| 104 |
kg/s |
| 105 |
m³/s |
| 106 |
m³/min |
| 107 |
m³/h |
| 108 |
lb |
| 109 |
STon |
| 110 |
LTon |
| 111 |
hl |
| 112 |
in³ |
| 113 |
gal |
| 114 |
ft³ |
| 115 |
bbl |
| 116 |
psi |
| 117 |
mmH2O |
| 118 |
mmHg |
| 119 |
inH2O |
| 120 |
ftH2O |
| 121 |
inHg |
| 122 |
torr |
| 123 |
Ml/d |
| 124 |
m³/d |
| 125 |
lb/s |
| 126 |
lb/min |
| 127 |
lb/h |
| 128 |
gal/s |
| 129 |
gal/min |
| 130 |
gal/h |
| 131 |
gal/d |
| 132 |
Mgal/d |
| 133 |
ft³/s |
| 134 |
ft³/min |
| 135 |
ft³/h |
| 136 |
ft³/d |
| 137 |
bbl/s |
| 138 |
bbl/min |
| 139 |
bbl/h |
| 140 |
bbl/d |
| 141 |
ImpGal/s |
| 142 |
ImpGal/min |
| 143 |
ImpGal/h |
| 144 |
ImpGal/d |
| 145 |
Application |
| 146 |
Special vessel feature |
| 147 |
Storage tank |
| 148 |
Stirred vessel |
| 149 |
Dosing vessel |
| 150 |
Pumping station |
| 151 |
Storm water overflow basin |
| 152 |
Vessel/Collecting basin |
| 153 |
Plastic vessel (measurement through the vessel top) |
| 154 |
Mobile plastic tank (IBC) |
| 155 |
Gauge measurement in waters |
| 156 |
Flow measurement flume/weir |
| 157 |
Demonstration |
| 158 |
Vessel form for bulk solids |
| 159 |
Silo (tall and narrow) |
| 160 |
Bunker (large volume) |
| 161 |
Heap (point measurement/profile detection) |
| 162 |
Crusher |
| 163 |
Medium |
| 164 |
Selection of the type of medium |
| 165 |
Solvents/Liquefied gases/Oils (DK < 3) |
| 166 |
Chemical mixtures (DK 3 ... 10) |
| 167 |
Water based solutions/Acids/Alkalis (DK > 10) |
| 168 |
Powder, dust (granulation size < 1 mm) |
| 169 |
Granules, pellets (granulation 1 ... 10 mm) |
| 170 |
Crushed stones, pebbles, boulders (granulation size > 10 mm) |
| 171 |
Type of medium |
| 172 |
Liquids |
| 173 |
Bulk solid |
| 174 |
Vessel bottom |
| 175 |
Selection of the existing vessel bottom for consideration in the signal processing. |
| 176 |
Flat |
| 177 |
Torispherical |
| 178 |
Conical |
| 179 |
Inclined |
| 180 |
Vessel height/Measuring range |
| 181 |
Vessel height or for applications without vessel the area in which the measured medium can move |
| 182 |
Vessel top |
| 183 |
Selection of the existing vessel top for consideration in the signal processing. |
| 184 |
Software version |
| 185 |
Version of the instrument software |
| 186 |
Device address |
| 187 |
Loop current mode |
| 188 |
Fixed current (4 mA) |
| 189 |
Analogue current output (4 ... 20 mA) |
| 190 |
Integration time (t) |
| 191 |
Damping of measured value peaks |
| 192 |
Linearization type |
| 193 |
Selection of the linearization curve |
| 194 |
Linear |
| 195 |
Horizontal cylindrical vessel |
| 196 |
Venturi, trapezoidal weir, rectangle weir |
| 197 |
Palmer-Bowlus Flume |
| 198 |
V-Notch, triangle weir |
| 199 |
Inclined bottom |
| 200 |
Conical bottom |
| 201 |
User programmable |
| 202 |
Distance B (min. adjustment) |
| 203 |
Distance from sensor reference plane to product surface at min. level |
| 204 |
Min. adjustment in % |
| 205 |
Level in percent for which the distance 'Distance B' must be entered |
| 206 |
Distance A (max. adjustment) |
| 207 |
Distance from sensor reference plane to product surface at max. level |
| 208 |
Max. adjustment in % |
| 209 |
Level in percent for which the distance 'Distance A' must be entered |
| 210 |
Distance |
| 211 |
Status distance |
| 212 |
Failure |
| 213 |
Upper limitation |
| 214 |
Lower limitation |
| 215 |
Simulation value |
| 216 |
Substitute value |
| 217 |
Constant value |
| 218 |
Out of specification |
| 219 |
Filling height |
| 220 |
Status filling height |
| 221 |
Lin. percent |
| 222 |
Percent |
| 223 |
Status percent |
| 224 |
Status lin. percent |
| 225 |
User defined |
| 226 |
Mgal |
| 227 |
ImpGal |
| 228 |
yd³ |
| 229 |
bbl_liq |
| 230 |
bush |
| 231 |
oz |
| 232 |
kg/m³ |
| 233 |
t/m³ |
| 234 |
kg/dm³ |
| 235 |
g/cm³ |
| 236 |
g/ml |
| 237 |
g/l |
| 238 |
lb/gal |
| 239 |
lb/in³ |
| 240 |
STon/yd³ |
| 241 |
deg Brix |
| 242 |
deg Baume lt |
| 243 |
deg Baume hv |
| 244 |
% sol wt |
| 245 |
% sol vol |
| 246 |
API |
| 247 |
pcf |
| 248 |
SGU |
| 249 |
g/s |
| 250 |
g/min |
| 251 |
g/h |
| 252 |
kg/min |
| 253 |
kg/h |
| 254 |
kg/d |
| 255 |
lb/d |
| 256 |
STon/min |
| 257 |
STon/h |
| 258 |
STon/d |
| 259 |
LTon/h |
| 260 |
LTon/d |
| 261 |
t/min |
| 262 |
t/h |
| 263 |
t/d |
| 264 |
pF |
| 265 |
ct/s |
| 266 |
lb/ft |
| 267 |
kg/m |
| 268 |
Hz |
| 269 |
V |
| 270 |
mV |
| 271 |
unknown |
| 272 |
m/s |
| 273 |
m/h |
| 274 |
ft/s |
| 275 |
ft/min |
| 276 |
Measurement reliability |
| 277 |
Status meas. reliability |
| 278 |
Scaled |
| 279 |
Status scaled |
| 280 |
Electronics temperature |
| 281 |
Actual electronics temperature |
| 282 |
Status electronics temperature |
| 283 |
Hardware version |
| 284 |
Hardware version of the main electronics |
| 285 |
0 |
| 286 |
Software version of the main electronics |
| 287 |
Factory calibration date |
| 288 |
Date of the last factory calibration |
| 289 |
Counter for change of parameters |
| 290 |
Date of the min. electronics temperature |
| 291 |
Max. distance |
| 292 |
Date of the max. distance |
| 293 |
Min. distance |
| 294 |
Date of the min. distance |
| 295 |
Max. measurement reliability |
| 296 |
Date of the max. measurement reliability |
| 297 |
Minimum measurement reliability |
| 298 |
Date of the min. measurement reliability |
| 299 |
Max. electronics temperature |
| 300 |
Date of the max. electronics temperature |
| 301 |
Min. electronics temperature |
| 302 |
Primary Variable (PV) |
| 303 |
Selection, which measured value should be outputted as Primary Variable (PV) |
| 304 |
Quaternary Variable (QV) |
| 305 |
Selection, which measured value should be outputted as Quaternary Variable (QV) |
| 306 |
Tertiary Variable (TV) |
| 307 |
Selection, which measured value should be outputted as Third Variable (TV) |
| 308 |
Secondary Variable (SV) |
| 309 |
Selection, which measured value should be outputted as Secondary Variable (SV) |
| 310 |
Function control |
| 311 |
Defines, if the diagnostic message 'Function check' should be outputted or suppressed |
| 312 |
OFF |
| 313 |
ON |
| 314 |
Maintenance required |
| 315 |
Defines, if the diagnostic message 'Maintenance required' should be outputted or suppressed |
| 316 |
Defines, if the diagnostic message 'Out of specification' should be outputted or suppressed |
| 317 |
Protection of parameter adjustment |
| 318 |
Activated (with device code) |
| 319 |
Sounded distance to the medium from the antenna edge |
| 320 |
Up to the entered distance (less a safety distance), all echoes will be stored as false signals |
| 321 |
False signal suppression |
| 322 |
Selection of an activity to process the gating out of false signals |
| 323 |
Create new |
| 324 |
Extend |
| 325 |
Delete all |
| 326 |
from |
| 327 |
Distance from the sensor reference plane to the range starting point |
| 328 |
to |
| 329 |
Distance from the sensor reference plane to the range end point |
| 330 |
Current output |
| 331 |
Device status acc. to NE 107 |
| 332 |
OK |
| 333 |
Failure |
| 334 |
Device status |
| 335 |
Detail status |
| 336 |
Detailed status value for identification of the exact cause of error |
| 337 |
HART Device Status |
| 338 |
Primary variable out of limits |
| 339 |
Non-primary variable out of limits |
| 340 |
Analog output saturated |
| 341 |
Analog output fixed |
| 342 |
More status available |
| 343 |
Cold start |
| 344 |
Configuration changed |
| 345 |
Field device malfunction |
| 346 |
MESSAGE |
| 347 |
Message stored in the instrument for free use |
| 348 |
LONG-TAG |
| 349 |
Graph |
| 350 |
Selection of the presentation for the measured value image |
| 351 |
Measured value |
| 352 |
Measured value with bar graph |
| 353 |
Two measured values |
| 354 |
Menu language |
| 355 |
Selection of the language for the indicating and adjustment module |
| 356 |
Deutsch |
| 357 |
English |
| 358 |
Français |
| 359 |
Español |
| 360 |
Português |
| 361 |
Italiano |
| 362 |
Nederlands |
| 363 |
Pycckuu |
| 364 |
Chinese |
| 365 |
Japanese |
| 366 |
Türkçe |
| 367 |
Lighting |
| 368 |
Activation of the background lighting of the indicating and adjustment module |
| 369 |
Display format 2 |
| 370 |
Selection of the requested formatting of the display value shown on the display and adjustment module |
| 371 |
Automatically |
| 372 |
###### |
| 373 |
Display format 1 |
| 374 |
Indication value 2 |
| 375 |
Determines which measured value should be displayed |
| 376 |
Display value |
| 377 |
Meas. rate |
| 378 |
Min. meas. rate |
| 379 |
Max. meas. rate |
| 380 |
Bluetooth access code |
| 381 |
The access code for the Bluetooth authentication consists of 6 characters. |
| 382 |
Send Bluetooth measured values (public) |
| 383 |
Activated |
| 384 |
Sensor acc. to WHG |
| 385 |
Use as a part of an overfill protection system according to WHG |
| 386 |
Simulation, current output |
| 387 |
Simulation, filling height |
| 388 |
Simulation filling height of the level |
| 389 |
Simulation, lin. percent |
| 390 |
Simulation, percent |
| 391 |
Simulation, distance |
| 392 |
Simulation, physical value |
| 393 |
Current range |
| 394 |
3.8 ... 20.5 mA |
| 395 |
4 ... 20 mA |
| 396 |
Output characteristic |
| 397 |
Selection of the current characteristics |
| 398 |
0 ... 100 % correspond to 4 ... 20 mA |
| 399 |
0 ... 100 % correspond to 20 ... 4 mA |
| 400 |
Behaviour in case of failure |
| 401 |
<= 3.6 mA |
| 402 |
>= 21 mA |
| 403 |
--- |
| 404 |
Password |
| 405 |
Simulation active |
| 406 |
PIN |
| 407 |
Determine the PIN which should be valid for the function 'Lock adjustment' |
| 408 |
04d |
| 409 |
Zoom range from |
| 410 |
Defines the start of the zoom area for presentation of the echo curve |
| 411 |
Zoom range up to |
| 412 |
Defines the end of the zoom area for presentation of the echo curve |
| 413 |
Fieldbus Profile Rev. |
| 414 |
Vessel height D |
| 415 |
Total height (inner dimension) |
| 416 |
Socket correction h |
| 417 |
Distance of the sensor reference plane to the upper edge of the vessel |
| 418 |
Intermediate height h |
| 419 |
The intermediate height 'h' specifies the height of the non-linear area for the linearization types 'Pyramid bottom', 'Conical bottom' or 'Inclined bottom' |
| 420 |
Function measured value filter |
| 421 |
Low averaging |
| 422 |
High averaging |
| 423 |
Mode of operation |
| 424 |
Mode of operation 1 |
| 425 |
Mode of operation 2 |
| 426 |
Mode of operation 3 |
| 427 |
Mode of operation 4 |
| 428 |
Extended functions |
| 429 |
Linearization |
| 430 |
Diagnostics |
| 431 |
Status |
| 432 |
Peak indicator |
| 433 |
Measured values |
| 434 |
Bild: Bedienung freigeben/sperren |
| 435 |
Bild: Messstellenname |
| 436 |
Bild: Einheiten |
| 437 |
Figure: Damping |
| 438 |
Figure: Current output |
| 439 |
Figure: Scaling |
| 440 |
Bild: Zugriffsschutz |
| 441 |
Figure: HART variables |
| 442 |
Figure: Reset |
| 443 |
Figure: Linearization |
| 444 |
Bild: Sensorinformationen |
| 445 |
Figure: Simulation |
| 446 |
Release/lock operation |
| 447 |
Settings in the special parameters were carried out. A change of application is only possible after resetting the sensor to delivery status. |
| 448 |
Units |
| 449 |
Adjustment |
| 450 |
Damping |
| 451 |
The sensor is in multidrop mode |
| 452 |
Scaling |
| 453 |
Access protection |
| 454 |
Interference behaviour |
| 455 |
HART variables |
| 456 |
Reset |
| 457 |
Status signals |
| 458 |
The instrument has a self-monitoring acc. to NE 107. Define the diagnostic states to be outputted by the instrument. |
| 459 |
Service login |
| 460 |
Special parameters |
| 461 |
1 |
| 462 |
2 |
| 463 |
5 |
| 464 |
6 |
| 465 |
15 |
| 466 |
16 |
| 467 |
Sensor information |
| 468 |
Counter for changes |
| 469 |
Measured value status |
| 470 |
Status, outputs |
| 471 |
Status, additional measured values |
| 472 |
Peak indicator, distance |
| 473 |
Peak indicator, reliability |
| 474 |
Peak indicator, meas. rate |
| 475 |
Peak indicator, electronics temperature |
| 476 |
Additional measured values |
| 477 |
Outputs |
| 478 |
Read values from device |
| 479 |
Write values to device |
| 480 |
Linearization table |
| 481 |
Linearization curve |
| 482 |
Table |
| 483 |
Echo curve |
| 484 |
--- |
| 485 |
Echo curve (curve) |
| 486 |
Show echo curve |
| 487 |
Settings |
| 488 |
Load actual echo curves |
| 489 |
Load selected curves |
| 490 |
Load false signal suppression |
| 491 |
Device characteristics |
| 492 |
Details |
| 493 |
Version |
| 494 |
Update instrument features |
| 495 |
Simulation |
| 496 |
Activate simulation |
| 497 |
Deactivate simulation |
| 498 |
Apply simulation value |
| 499 |
Identification |
| 500 |
Service login required |
| 501 |
Measured value memory (EDD) |
| 502 |
Device Settings |
| 503 |
Process Variables |
| 504 |
Offline |
| 505 |
Maintenance |
| 506 |
Service logout |
| 507 |
Carry out reset? |
| 508 |
Reset 'Configuration changed' |
| 509 |
Reset peak indicator |
| 510 |
UpdateHealthStatus |
| 511 |
VEGAPULS C 20 series |
| 512 |
VEGA Grieshaber KG |
| 513 |
C700 - Simulation active |
| 514 |
Terminate simulation
Wait for the automatic end
|
| 515 |
F260 - Error in the calibration |
| 516 |
Exchanging the electronics
Send instrument for repair
|
| 517 |
F261 - Error in the device setting |
| 518 |
Repeat setup
Carry out a reset
|
| 519 |
F265 - Measurement function disturbed |
| 520 |
Check operating voltage
Carry out a reset
Briefly separate operating voltage
|
| 521 |
F013 - No measured value available |
| 522 |
Check installation and/or parameter adjustment
Clean or exchange process component or antenna
|
| 523 |
F017 - Adjusted span too small |
| 524 |
Change adjustment according to the limit values
|
| 525 |
F025 - Error in the linearization table |
| 526 |
Check linearization table
Delete table/Create new
|
| 527 |
F036 - No executable software |
| 528 |
Repeat software update
Check electronics version
Exchanging the electronics
Send instrument for repair
|
| 529 |
F040 - Error in the electronics |
| 530 |
F080 - General software error |
| 531 |
Briefly separate operating voltage
|
| 532 |
F105 - Measured value is determined |
| 533 |
Wait for switch-on phase
|
| 534 |
M511 - Inconsistent software configuration |
| 535 |
Carry out oftware update
|
| 536 |
S600 - Inpermissible electronics temperature |
| 537 |
Check ambient temperature
Insulate electronics
|
| 538 |
S601 - Overfilling |
| 539 |
Make sure that there is no further filling
Check level in the vessel
|
| 540 |
S603 - Impermissible operating voltage |
| 541 |
Check operating voltage
Increase operating voltage
|
| 542 |
M500 - Error in the delivery status |
| 543 |
Repeat reset
Load XML file with sensor data into the sensor
|
| 544 |
M501 - Error in inactive linearization table |
| 545 |
M507 - Error in the device setting |
| 546 |
Carry out a reset
|
| 547 |
M508 - No executable Bluetooth software |
| 548 |
M509 - Software update running |
| 549 |
Wait until software update is finished
|
| 550 |
M510 - No communication with the main controller |
| 551 |
Exchanging the electronics
Restart device
|
| 552 |
Error message |
| 553 |
Note |
| 554 |
Meas. reliability, level |
| 555 |
Unlock adjustment |
| 556 |
Lock adjustment |
| 557 |
Modify |
| 558 |
Execute |
| 559 |
Common Tables |
| 560 |
Interoperable * |
| 561 |
Universal |
| 562 |
Common Practice |
| 563 |
Pressure Universal |
| 564 |
Pressure Common |
| 565 |
Menu |
| 566 |
Rosemount Magflow |
| 567 |
Rosemount Pressure |
| 568 |
Moore Products |
| 569 |
Siemens Pressure |
| 570 |
P2 Common |
| 571 |
PV |
| 572 |
Wireless |
| 573 |
Munge |
| 574 |
Analytical Oxygen/Combustion/Methane/CO |
| 575 |
Flow Totalizer - Rate Indicator |
| 576 |
Flow Variable Area |
| 577 |
Flow Coriolis Mass |
| 578 |
Flow Ultrasonic - Gas |
| 579 |
Flow Ultrasonic - Liquid |
| 580 |
Level Ultrasonic |
| 581 |
Level Radar - Microwave |
| 582 |
Pressure Absolute |
| 583 |
Level Capacitance |
| 584 |
Pressure Differential |
| 585 |
Level Hydrostatic |
| 586 |
Level |
| 587 |
Pressure Absolute/Relative |
| 588 |
Level Microwave |
| 589 |
Level Radar |
| 590 |
Level Density - Nuclear |
| 591 |
Flow Electromagnetic |
| 592 |
Flow Vortex |
| 593 |
Flow Magmeter - Rack Version |
| 594 |
Flow High Performance Magmeter |
| 595 |
Flow Mass |
| 596 |
Flow Ultrasonic |
| 597 |
Flow Magnetic |
| 598 |
Flow Magnetic - Custody Transfer |
| 599 |
Flow 2-wire Magnetic |
| 600 |
Flow Coriolis Mass - Custody Transfer |
| 601 |
Flow 2-wire Vortex |
| 602 |
Flow Thermal |
| 603 |
Temperature Head Mounted |
| 604 |
Temperature Compact |
| 605 |
Temperature DIN Rail Mounted |
| 606 |
Analytical pH |
| 607 |
Analytical Conductivity - Conductive |
| 608 |
Analytical Conductivity - Inductive |
| 609 |
Temperature Sensor |
| 610 |
Level Servo |
| 611 |
Temperature DIN Rail |
| 612 |
Temperature |
| 613 |
Analytical ORP |
| 614 |
Analytical pION |
| 615 |
Analytical IConc |
| 616 |
Analytical Electrode Conductivity |
| 617 |
Analytical Toroidal Conductivity |
| 618 |
Valve Positioner |
| 619 |
Valve Controller |
| 620 |
Pressure |
| 621 |
Pressure Multivariable |
| 622 |
Analytical pH/ORP |
| 623 |
Flow Coriolis |
| 624 |
Analytical Conductivity |
| 625 |
Valve Positioner/Pneumatic |
| 626 |
Valve Actuator - Electrical |
| 627 |
Temperature Dual Input |
| 628 |
Valve Actuator |
| 629 |
Analytical Corrosion |
| 630 |
Analytical Density - Nuclear |
| 631 |
Level Continuous Gamma |
| 632 |
Level Laser Ranging |
| 633 |
Pressure Safety |
| 634 |
Flow Vortex/Swirl |
| 635 |
Flow |
| 636 |
Analytical 4 Electrode Conductivity |
| 637 |
Analytical 2 Electrode Conductivity |
| 638 |
Analytical Troidal Conductivity |
| 639 |
Analytical pH/ORP/pIon/Ion Conc |
| 640 |
Analytical Oxygen |
| 641 |
Pressure P, dP + Multivariable |
| 642 |
Temperature 2-wire |
| 643 |
Pressure w/ PID |
| 644 |
Pressure Saturated Steam |
| 645 |
Analytical Density - Gamma Ray |
| 646 |
Level Gamma Ray |
| 647 |
Analytical Weight - Gamma Ray |
| 648 |
Level w/ Density - Gamma Ray |
| 649 |
Analytical Motorized Density |
| 650 |
Flow Multivariable Mass |
| 651 |
Temperature Multivariable |
| 652 |
Specialty HART-to-Analog Signal Conv |
| 653 |
Flow dP |
| 654 |
Pressure Low Power |
| 655 |
Pressure Certified SIL2 |
| 656 |
Interoperable |
| 657 |
Analytical Density |
| 658 |
Valve Positioner/Electropneumatic |
| 659 |
Flow Magnetic Inductive |
| 660 |
Analytical |
| 661 |
Analytical Opacity Monitor |
| 662 |
Analytical Oxygen/Combustion |
| 663 |
Analytical 2-wire Conductivity |
| 664 |
Analytical 2-wire Conductivity w/ pure H20 |
| 665 |
Analytical 2-wire Conductivity w/ % conc |
| 666 |
Analytical 2-wire Oxygen/Chlorine/Ozone |
| 667 |
Analytical 2-wire pH/ORP |
| 668 |
Analytical 2-wire Contacting/Toroidal |
| 669 |
Analytical Oxygen - High Temperature |
| 670 |
Analytical Conductivity w/ % conc |
| 671 |
Analytical pH/ORP/ISE |
| 672 |
Analytical Amperometric Analyzer |
| 673 |
Analytical Dual Input Analyzer |
| 674 |
Pressure Pressure/Level |
| 675 |
Analytical Consistency |
| 676 |
Analytical Microwave-Pulp Consistency |
| 677 |
Analytical Microwave Consistency |
| 678 |
Valve Digital Positioner |
| 679 |
Valve Smart Valve Positioner |
| 680 |
Temperature Differential |
| 681 |
Analytical Dissolved Oxygen |
| 682 |
Analytical pH Controller |
| 683 |
Analytical Conductivity/Resistivity Controller |
| 684 |
Analytical Conductivity/Resistivity |
| 685 |
Level Displacement |
| 686 |
Temperature w/ PID |
| 687 |
Valve Universal Positioner |
| 688 |
Level Radar - Reflex |
| 689 |
Pressure Gauge |
| 690 |
Pressure Sealed Gauge |
| 691 |
Valve Digital Positioner w/ PID |
| 692 |
Valve Intelligent Positioner |
| 693 |
Analytical Gas Detector |
| 694 |
Analytical Infrared Gas Detector |
| 695 |
Analytical Electrochemical Gas Detector |
| 696 |
Analytical Measuring Instruments |
| 697 |
Level Magnostrictive |
| 698 |
Valve On/Off Valve Controller |
| 699 |
Level Radar - Pulse |
| 700 |
Level Continuous Capactive |
| 701 |
Valve Damper Actuator |
| 702 |
Valve Electric Damper Actuator |
| 703 |
Flow Electronic |
| 704 |
Flow Vortex - Multiparameter Mass |
| 705 |
Analytical UV Flame Detector |
| 706 |
Analytical UVIR Flame Detector |
| 707 |
Analytical IR Flame Detector |
| 708 |
Analytical Fire Detector |
| 709 |
Analytical Gas Detector Display Interface |
| 710 |
Analytical Toxic Gas Detector |
| 711 |
Analytical Flame Detector |
| 712 |
Level Nuclear |
| 713 |
Analytical Microwave |
| 714 |
Analytical Density - Radiometric |
| 715 |
Level Radiometric |
| 716 |
Analytical Gas/Steam |
| 717 |
Level Nucleonic |
| 718 |
Analytical Blade Consistency |
| 719 |
Analytical Rotary Consistency |
| 720 |
Pressure Absolute/Differential |
| 721 |
Positioner |
| 722 |
Analytical Combustible Gas Detector |
| 723 |
Analytical Point Infrared Gas Detector |
| 724 |
Analytical Multi-Detector Monitor System |
| 725 |
Valve Positioner/Electro-hydraulic |
| 726 |
Valve Monitor |
| 727 |
Enable on token-passing data link layer only |
| 728 |
Enable on TDMA data link layer only |
| 729 |
Enable on both TDMA and token-passing data link layer |
| 730 |
WirelessHART Device |
| 731 |
IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation |
| 732 |
Primary |
| 733 |
Primary Analog Channel |
| 734 |
Secondary |
| 735 |
Secondary Analog Channel |
| 736 |
Tertiary |
| 737 |
Tertiary Analog Channel |
| 738 |
Quaternary |
| 739 |
Quaternary Analog Channel |
| 740 |
Quinary |
| 741 |
Quinary Analog Channel |
| 742 |
Critical Power Failure |
| 743 |
Lock all |
| 744 |
Trim not supported |
| 745 |
Configuration cannot be changed |
| 746 |
Locked by gateway |
| 747 |
Analog Input Channel |
| 748 |
Analog Output Channel |
| 749 |
Secondary Analog Channel Saturated |
| 750 |
Tertiary Analog Channel Saturated |
| 751 |
Quaternary Analog Channel Saturated |
| 752 |
Quinary Analog Channel Saturated |
| 753 |
Secondary Analog Channel Fixed |
| 754 |
Tertiary Analog Channel Fixed |
| 755 |
Quaternary Analog Channel Fixed |
| 756 |
Quinary Analog Channel Fixed |
| 757 |
Simulation active |
| 758 |
The device is in simulation mode and the level output is not representative of the process. |
| 759 |
Non-Volatile memory failure |
| 760 |
The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed. |
| 761 |
Volatile memory error |
| 762 |
The RAM memory check is invalid or maybe corrupt |
| 763 |
Watchdog reset executed |
| 764 |
A watchdog reset has been performed |
| 765 |
Voltage conditions out of range |
| 766 |
A voltage condition is outside its allowable range |
| 767 |
Environmental conditions out of range |
| 768 |
An internal or environmental condition is beyond acceptable limits. |
| 769 |
Electronic failure |
| 770 |
A hardware problem not related to the sensor has been detected. |
| 771 |
Subdevice list changed |
| 772 |
Duplicate master detected |
| 773 |
Capacity Denied |
| 774 |
The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified |
| 775 |
Bandwidth allocation pending |
| 776 |
Block transfer pending |
| 777 |
Continuous |
| 778 |
The Burst Message is published continuously at (worst case) the Minimum Update Period. |
| 779 |
Window |
| 780 |
The Burst Message is triggered when the source value deviates more than the specified trigger value |
| 781 |
Rising |
| 782 |
The Burst Message is triggered when source value Rises Above the specified trigger value. |
| 783 |
Falling |
| 784 |
The Burst Message is triggered when the source value Falls Below the specified trigger value. |
| 785 |
On-change |
| 786 |
The Burst Message is triggered when any value in the message changes. |
| 787 |
Battery life |
| 788 |
Percent range |
| 789 |
Loop current |
| 790 |
Primary variable |
| 791 |
Secondary variable |
| 792 |
Tertiary variable |
| 793 |
Quaternary variable |
| 794 |
Off |
| 795 |
Enable event notification on token-passing data link layer |
| 796 |
Enable event notification on TDMA data link layer |
| 797 |
Enable event notification on TDMA and token-passing data link layer |
| 798 |
Configuration changed event pending |
| 799 |
Device status event pending |
| 800 |
More status available event pending |
| 801 |
Disable |
| 802 |
Enable single data point trending |
| 803 |
Enable filtered trending |
| 804 |
The sample is filtered using a time constant equal to one-third the trend sample period |
| 805 |
Enable average trending |
| 806 |
The value obtained by dividing the sum of all samples in the period by the total number of samples |
| 807 |
Read receive time |
| 808 |
Write date and time |
| 809 |
Non-Volatile Clock |
| 810 |
When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure. |
| 811 |
Clock Uninitialized |
| 812 |
The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device. |
| 813 |
Line Power |
| 814 |
Device is powered via a hardwired connection to a plant power source. |
| 815 |
Battery Power |
| 816 |
Device operates solely of its (internal) battery. |
| 817 |
Recharg.B./Power Sc. |
| 818 |
Rechargeable battery power or power scavenging. The device has a short-term supply of energy (must be at least one hour) that is continuously being replenished. The device's power is being replenished by harvesting and converting energy from the environment surrounding the device (e.g. solar, vibration, heat). |
| 819 |
Idle |
| 820 |
Active search |
| 821 |
Looking for neighbors. |
| 822 |
Negotiating |
| 823 |
Quarantined |
| 824 |
Operational |
| 825 |
Suspended |
| 826 |
Deep sleep |
| 827 |
Ultra-low power |
| 828 |
Wireless Signal Found |
| 829 |
Network packets have been recognized |
| 830 |
Wireless Signal Identified |
| 831 |
Wireless Time Synchronized |
| 832 |
WirelessHart Signal Identified |
| 833 |
Network Admission Requested |
| 834 |
Set on transmission of first join request |
| 835 |
Join Retrying |
| 836 |
Set after the first join request retry (i.e. when number of join requests > 2). Cleared when device is authenticated or when Active Search started. |
| 837 |
Join Failed |
| 838 |
Set on transition from Active Search mode to Deep Sleep mode. Cleared on transition from Deep Sleep to Active Search. |
| 839 |
Network Security Clearance Granted |
| 840 |
Network Manager Session Established |
| 841 |
Network Joined |
| 842 |
Network Joined. Normal superframe and links obtained. |
| 843 |
Network Bandwidth Requested |
| 844 |
Negotiating Network Properties. Gateway session obtained. |
| 845 |
Join Complete |
| 846 |
Normal operating mode. |
| 847 |
None |
| 848 |
No restrictions |
| 849 |
SI Only |
| 850 |
Restricted to SI Unit codes only |
| 851 |
Open - accept all devices |
| 852 |
Use Whitelist for access |
| 853 |
Use Blacklist |
| 854 |
Use Whitelist and Blacklist |
| 855 |
Lockdown - disable join links |
| 856 |
Process automation device |
| 857 |
Discrete device |
| 858 |
Hybrid:Process automation+discrete |
| 859 |
I/O System |
| 860 |
WirelessHART Process automation device |
| 861 |
WirelessHART Discrete device |
| 862 |
WirelessHART Process automation+discrete |
| 863 |
WirelessHART Gateway |
| 864 |
WirelessHART Access point |
| 865 |
WirelessHART Process adapter |
| 866 |
WirelessHART Discrete adapter |
| 867 |
WirelessHART enabled handheld/portable maintenance tool |
| 868 |
Don't attempt to join |
| 869 |
Join now |
| 870 |
Attempt to join immediately on powerup or reset |
| 871 |
US |
| 872 |
United States of America |
| 873 |
JP |
| 874 |
Japan |
| 875 |
DE |
| 876 |
Germany |
| 877 |
FR |
| 878 |
France |
| 879 |
ES |
| 880 |
Spain |
| 881 |
RU |
| 882 |
Russian Federation |
| 883 |
CN |
| 884 |
People's Republic of China |
| 885 |
Nominal |
| 886 |
Device Power Status is nominal |
| 887 |
Low |
| 888 |
Device Power Status is low |
| 889 |
Critically Low |
| 890 |
Device Power Status is critically low |
| 891 |
Recharging - Low |
| 892 |
Recharging - High |
| 893 |
Secondary Master |
| 894 |
Primary Master |
| 895 |
PV Analog Channel Saturated |
| 896 |
PV Analog Channel Fixed |
| 897 |
Device Profile |
| 898 |
Device Diagnostic Status 0 |
| 899 |
Device Diagnostic Status 1 |
| 900 |
I/O and Subdevice Status |
| 901 |
WirelessHART Status |
| 902 |
Time Set Option |
| 903 |
Real Time Clock Flags |
| 904 |
Country |
| 905 |
Country of intended device installation |
| 906 |
SI Unit Control |
| 907 |
Indicates if device should only display SI unit codes |
| 908 |
Burst Trigger Units |
| 909 |
Burst Trigger Class |
| 910 |
Wired HART Enabled |
| 911 |
Enabled on Wired HART device connection only |
| 912 |
Wireless HART Enabled |
| 913 |
Enabled on WirelessHART device connection only |
| 914 |
Both Wired and WirelessHart Enabled |
| 915 |
Enabled on both Wired and WirelessHART connections |
| 916 |
Burst Msg Trigger Mode |
| 917 |
Event Status |
| 918 |
Event Notification Control |
| 919 |
Operate mode Mask |
| 920 |
Not Defined |
| 921 |
Power Source |
| 922 |
Power source of the device |
| 923 |
Wireless Mode |
| 924 |
Join Status |
| 925 |
The current location in the joining sequence of operations. |
| 926 |
Network Access Mode |
| 927 |
Join Mode |
| 928 |
Power Status |
| 929 |
Power status of the device |
| 930 |
Master Mode |
| 931 |
This sets the I/O System's Data Link Layer operation on all channels as either primary or secondary master mode. |
| 932 |
Trend Units |
| 933 |
Trend Device Variable Unit Code |
| 934 |
Trend Classification |
| 935 |
Trend Device Variable Classification |
| 936 |
Trend Control |
| 937 |
Device Status Mask |
| 938 |
Ext dev status Mask |
| 939 |
Device Diagnostic Status 0 Mask |
| 940 |
Device Diagnostic Status 1 Mask |
| 941 |
Device Diagnostic Status 2 Mask |
| 942 |
Device Diagnostic Status 3 Mask |
| 943 |
AO saturated Mask |
| 944 |
AO fixed Mask |
| 945 |
Latched Device Status |
| 946 |
Latched Ext dev status |
| 947 |
Latched Operate Mode |
| 948 |
Latched Device Diagnostic Status 0 |
| 949 |
Latched Device Diagnostic Status 1 |
| 950 |
Latched Device Diagnostic Status 2 |
| 951 |
Latched Device Diagnostic Status 3 |
| 952 |
Latched AO saturated |
| 953 |
Latched AO fixed |
| 954 |
Wireless Module Device Type |
| 955 |
Device type of the Wireless Radio |
| 956 |
Wireless Module Manufacturer ID |
| 957 |
Manufacturer of the Wireless Radio contained in this device |
| 958 |
Subdevice Device Type |
| 959 |
Device type of the subdevice attached to this system. |
| 960 |
Subdevice Manufacturer Id |
| 961 |
Manufacturer of the subdevice attached to this system. |
| 962 |
Time Stamp |
| 963 |
Relative time value on network |
| 964 |
8u |
| 965 |
Dynamic Variables Returned for Device Variables |
| 966 |
Command Response Truncated |
| 967 |
Configuration Change Counter Mismatch |
| 968 |
Status bytes mismatch |
| 969 |
8.3f |
| 970 |
Device Variable |
| 971 |
No echo curve available |
| 972 |
No echo curve loaded |
| 973 |
Execute action |
| 974 |
Action successfully carried out. |
| 975 |
Features were updated. |
| 976 |
The instrument is locked! The action cannot be executed. |
| 977 |
The password is wrong! |
| 978 |
Sounded distance from the sealing surface to the medium |
| 979 |
Failure while executing the action |
| 980 |
Do you really want to reset the selected peak indicators? |
| 981 |
; |
| 982 |
Device code |
| 983 |
000000 |
| 984 |
pin |
| 985 |
Waiting time until the next attempt |
| 986 |
Parameter adjustment blocked |
| 987 |
Enter the actually valid device code. |
| 988 |
Wrong device code |
| 989 |
|
| 990 |
Enter emergency code |
| 991 |
? |
| 992 |
Enter the device unlock code. |
| 993 |
Wrong PIN |