| 0 |
DD Thermo ID |
| 1 |
DD Revision ID for Thermo QA Control |
| 2 |
01.000 |
| 3 |
AutoXP |
| 4 |
Thermo MeasureTech |
| 5 |
System Status |
| 6 |
DP: IO Failure |
| 7 |
PRESS: IO Failure |
| 8 |
RTD: IO Failure |
| 9 |
Low Battery Volts |
| 10 |
DP Status |
| 11 |
DP: LO Alarm |
| 12 |
DP: LOLO Alarm |
| 13 |
DP: HI Alarm |
| 14 |
DP: HIHI Alarm |
| 15 |
DP: Out Of Range |
| 16 |
DP: ManOvrd |
| 17 |
DP: In Calibration |
| 18 |
Pressure Status |
| 19 |
PRESS: LO Alarm |
| 20 |
PRESS: LOLO Alarm |
| 21 |
PRESS: HI Alarm |
| 22 |
PRESS: HIHI Alarm |
| 23 |
PRESS: Out Of Range |
| 24 |
PRESS: ManOvrd |
| 25 |
PRESS: In Calibration |
| 26 |
Temperature Status |
| 27 |
RTD: LO Alarm |
| 28 |
RTD: LOLO Alarm |
| 29 |
RTD: HI Alarm |
| 30 |
RTD: HIHI Alarm |
| 31 |
RTD: Out Of Range |
| 32 |
RTD: ManOvrd |
| 33 |
RTD: In Calibration |
| 34 |
Spare#1 Status |
| 35 |
Not Used |
| 36 |
Spare#2 Status |
| 37 |
06X |
| 38 |
DP |
| 39 |
Differential Pressure Live Value |
| 40 |
DP Units |
| 41 |
Units for Differential Pressure |
| 42 |
DP Dev fmly |
| 43 |
DP Class |
| 44 |
DP PDQ |
| 45 |
DP LS |
| 46 |
DP Fmly stat |
| 47 |
DP USL |
| 48 |
Differential Pressure Upper Sensor Limit |
| 49 |
DP LSL |
| 50 |
Differential Pressure Lower Sensor Limit |
| 51 |
DP MinSpan |
| 52 |
Differential Pressure Minimum Span |
| 53 |
DP Damping |
| 54 |
Differential Pressure Damping Value |
| 55 |
.0f |
| 56 |
8.0f |
| 57 |
DP Update Period |
| 58 |
Differential Pressure Update Period |
| 59 |
DP Serial No. |
| 60 |
7d |
| 61 |
DP Lower trim |
| 62 |
DP Upper trim |
| 63 |
DP Trim support |
| 64 |
DP Min lower trim |
| 65 |
DP Max lower trim |
| 66 |
DP Min upper trim |
| 67 |
DP Max upper trim |
| 68 |
DP Min trim diff |
| 69 |
DP Simulate |
| 70 |
|
| 71 |
Cal Status |
| 72 |
DP Input Calibration Status |
| 73 |
Normal |
| 74 |
Input Is in Normal Mode |
| 75 |
In Calib |
| 76 |
Input is in Calibration Mode |
| 77 |
Cal. Index Counter |
| 78 |
DP Input Calibration Index Count |
| 79 |
EU ZO Val |
| 80 |
Cal. Pt #1 EU Zero Value |
| 81 |
Raw ZO Val |
| 82 |
Cal. Pt #1 Raw Zero Value |
| 83 |
Volts |
| 84 |
EU Mid Val |
| 85 |
Cal. Pt #2 EU Mid Value |
| 86 |
Raw Mid Val |
| 87 |
Cal. Pt #2 Raw Mid Value |
| 88 |
EU FS Val |
| 89 |
Cal. Pt #3 EU Full Scale Value |
| 90 |
Raw FS Val |
| 91 |
Cal. Pt #3 Raw Full Scale Value |
| 92 |
Prev. EU ZO Val |
| 93 |
Prev. Cal. Pt #1 EU Zero Value |
| 94 |
Prev. Raw ZO Val |
| 95 |
Prev. Cal. Pt #1 Raw Zero Value |
| 96 |
Prev. EU Mid Val |
| 97 |
Prev. Cal. Pt #2 EU Mid Value |
| 98 |
Prev. Raw Mid Val |
| 99 |
Prev. Cal. Pt #2 Raw Mid Value |
| 100 |
Prev. EU FS Val |
| 101 |
Prev. Cal. Pt #3 EU Full Scale Value |
| 102 |
Prev. Raw FS Val |
| 103 |
Prev. Cal. Pt #3 Raw Full Scale Value |
| 104 |
Current Value |
| 105 |
Differential Pressure Input Current Used Value |
| 106 |
EU Value |
| 107 |
Differential Pressure Input EU Value |
| 108 |
Raw Value |
| 109 |
DP Raw Value |
| 110 |
Alarm Enable |
| 111 |
DP Limit Alarm Enable |
| 112 |
LO Alarm |
| 113 |
LOLO Alarm |
| 114 |
HI Alarm |
| 115 |
HIHI Alarm |
| 116 |
LO Value |
| 117 |
HI Value |
| 118 |
LOLO Limit |
| 119 |
Differential Pressure Input LOLO Alarm Limit |
| 120 |
LO Limit |
| 121 |
Differential Pressure Input LO Alarm Limit |
| 122 |
HI Limit |
| 123 |
Differential Pressure Input HI Alarm Limit |
| 124 |
HIHI Limit |
| 125 |
Differential Pressure Input HIHI Alarm Limit |
| 126 |
LO Value Limit |
| 127 |
Differential Pressure Input LO Value Limit |
| 128 |
HI Value Limit |
| 129 |
Differential Pressure Input HI Value Limit |
| 130 |
Mode |
| 131 |
Differential Pressure Input Manual/Live Input Selection |
| 132 |
Live |
| 133 |
Input set to Live Mode |
| 134 |
Manual |
| 135 |
Input set to manual Mode |
| 136 |
Manual Value |
| 137 |
Differential Pressure Input Manual Value |
| 138 |
Differential Pressure |
| 139 |
Simulate |
| 140 |
Update Period |
| 141 |
DiffPressCal |
| 142 |
Differential Pressure Calibration |
| 143 |
Diff Press Cal Status |
| 144 |
Cal, Index Count |
| 145 |
EU Zero Cal |
| 146 |
EU Zero Calibration Point #1 |
| 147 |
Raw Zero Cal |
| 148 |
Raw Zero Calibration Point #1 |
| 149 |
EU Mid Cal |
| 150 |
EU Mid Calibration Point #2 |
| 151 |
Raw Mid Cal |
| 152 |
Raw Mid Calibration Point #2 |
| 153 |
EU FS Cal |
| 154 |
EU Full Scale Calibration Point #3 |
| 155 |
Raw FS Cal |
| 156 |
Raw Full Scale Calibration Point #3 |
| 157 |
Prev EU Zero Cal |
| 158 |
Prev EU Zero Calibration Point #1 |
| 159 |
Prev Raw Zero Cal |
| 160 |
Prev Raw Zero Calibration Point #1 |
| 161 |
Prev EU Mid Cal |
| 162 |
Prev EU Mid Calibration Point #2 |
| 163 |
Prev Raw Mid Cal |
| 164 |
Prev Raw Mid Calibration Point #2 |
| 165 |
Prev EU FS Cal |
| 166 |
Prev EU Full Scale Calibration Point #3 |
| 167 |
Prev Raw FS Cal |
| 168 |
Prev Raw Full Scale Calibration Point #3 |
| 169 |
DiffPressLimits |
| 170 |
Differential Pressure Alarm Limits |
| 171 |
Limit Enable |
| 172 |
Limit Alarm Enable |
| 173 |
LOLO alarm Limit |
| 174 |
LO alarm Limit |
| 175 |
HI alarm Limit |
| 176 |
HIHI alarm Limit |
| 177 |
LOVal Limit |
| 178 |
HIVal Limit |
| 179 |
DiffPressInput |
| 180 |
Differential Pressure Input Data |
| 181 |
Curr Value |
| 182 |
Current USed Value |
| 183 |
Raw Value in Volts |
| 184 |
Manual Mode |
| 185 |
Manual/Input Mode Selection |
| 186 |
Manual Mode Value |
| 187 |
.3f |
| 188 |
Pres Dev fmly |
| 189 |
Pres Class |
| 190 |
Pres PDQ |
| 191 |
Pres LS |
| 192 |
Pres Fmly stat |
| 193 |
Pressure Update Period |
| 194 |
Pres Lower trim |
| 195 |
Pres Upper trim |
| 196 |
Pres Trim support |
| 197 |
Pres Min lower trim |
| 198 |
Pres Max lower trim |
| 199 |
Pres Min upper trim |
| 200 |
Pres Max upper trim |
| 201 |
Pres Min trim diff |
| 202 |
Presure Input Calibration Status |
| 203 |
Pressure Input Calibration Index Count |
| 204 |
Pressure Cal. Pt #1 EU Zero Value |
| 205 |
Pressure Cal. Pt #1 Raw Zero Value |
| 206 |
Pressure Cal. Pt #2 EU Mid Value |
| 207 |
Pressure Cal. Pt #2 Raw Mid Value |
| 208 |
Pressure Cal. Pt #3 EU Full Scale Value |
| 209 |
Pressure Cal. Pt #3 Raw Full Scale Value |
| 210 |
Prev. Pressure Cal. Pt #1 EU Zero Value |
| 211 |
Prev. Pressure Cal. Pt #1 Raw Zero Value |
| 212 |
Prev. Pressure Cal. Pt #2 EU Mid Value |
| 213 |
Prev. Pressure Cal. Pt #2 Raw Mid Value |
| 214 |
Prev. Pressure Cal. Pt #3 EU Full Scale Value |
| 215 |
Prev. Pressure Cal. Pt #3 Raw Full Scale Value |
| 216 |
Pressure Input Current Used Value |
| 217 |
Pressure EU Value |
| 218 |
Pressure Raw Value |
| 219 |
Pressure Limit Alarm Enable |
| 220 |
Pressure Input LOLO Alarm Limit |
| 221 |
Pressure Input LO Alarm Limit |
| 222 |
Pressure Input HI Alarm Limit |
| 223 |
Pressure Input HIHI Alarm Limit |
| 224 |
Pressure Input LO Value Limit |
| 225 |
Pressure Input HI Value Limit |
| 226 |
Pressure Input Manual/Live Input Selection |
| 227 |
Pressure Input Manual Value |
| 228 |
PressureCal |
| 229 |
Pressure Calibration |
| 230 |
Pressure Cal Status |
| 231 |
PressureLimits |
| 232 |
Pressure Alarm Limits |
| 233 |
PressureInput |
| 234 |
Pressure Input Data |
| 235 |
RTDTemp |
| 236 |
RTD Temperature Live Value |
| 237 |
RTDTemp Units |
| 238 |
Units for RTD Temperature |
| 239 |
RTDTemp Dev fmly |
| 240 |
RTDTemp Class |
| 241 |
RTDTemp PDQ |
| 242 |
RTDTemp LS |
| 243 |
RTDTemp Fmly stat |
| 244 |
RTDTemp USL |
| 245 |
RTD Temperature Upper Sensor Limit |
| 246 |
RTDTemp LSL |
| 247 |
RTD Temperature Lower Sensor Limit |
| 248 |
RTDTemp MinSpan |
| 249 |
RTD Temperature Minimum Span |
| 250 |
RTDTemp Damping |
| 251 |
RTD Temperature Damping Value |
| 252 |
RTDTemp Update Period |
| 253 |
RTD Temperature Update Period |
| 254 |
RTDTemp Serial No. |
| 255 |
RTDTemp Lower trim |
| 256 |
RTDTemp Upper trim |
| 257 |
RTDTemp Trim support |
| 258 |
RTDTemp Min lower trim |
| 259 |
RTDTemp Max lower trim |
| 260 |
RTDTemp Min upper trim |
| 261 |
RTDTemp Max upper trim |
| 262 |
RTDTemp Min trim diff |
| 263 |
RTDTemp Simulate |
| 264 |
RTD Temp Input Calibration Status |
| 265 |
RTD Temperature Input Calibration Index Count |
| 266 |
RTD Temperature Cal. Pt #1 EU Zero Value |
| 267 |
RTD Temperature Cal. Pt #1 Raw Zero Value |
| 268 |
RTD Temperature Cal. Pt #1 EU Mid Value |
| 269 |
RTD Temperature Cal. Pt #1 Raw Mid Value |
| 270 |
RTD Temperature Cal. Pt #1 EU Full Scale Value |
| 271 |
RTD Temperature Cal. Pt #1 Raw Full Scale Value |
| 272 |
Prev. RTD Temperature Cal. Pt #1 EU Zero Value |
| 273 |
Prev. RTD Temperature Cal. Pt #1 Raw Zero Value |
| 274 |
Prev. RTD Temperature Cal. Pt #2 EU Mid Value |
| 275 |
Prev. RTD Temperature Cal. Pt #2 Raw Mid Value |
| 276 |
Prev. RTD Temperature Cal. Pt #3 EU Full Scale Value |
| 277 |
Prev. RTD Temperature Cal. Pt #3 Raw Full Scale Value |
| 278 |
RTD Temperature Input Current Used Value |
| 279 |
RTD Temperature Input EU Value |
| 280 |
RTD Temperature Input Raw Value |
| 281 |
RTD Temperature Input Limit Alarm Enable |
| 282 |
RTD Temperature Input LOLO Alarm Limit |
| 283 |
RTD Temperature Input LO Value Alarm Limit |
| 284 |
RTD Temperature Input HI Value Alarm Limit |
| 285 |
RTD Temperature Input HIHI Alarm Limit |
| 286 |
RTD Temperature Input LO Value Limit |
| 287 |
RTD Temperature Input HI Value Limit |
| 288 |
RTDTemp Manual/Live Input Selection |
| 289 |
RTD Temperature Input Manual Value |
| 290 |
RTD Temperature |
| 291 |
RTDTempCal |
| 292 |
RTD Temperature Calibration |
| 293 |
RTD Temp Cal Status |
| 294 |
RTD Temp Input Calibration Index Count |
| 295 |
RTDTempLimits |
| 296 |
RTD Temperature Alarm Limits |
| 297 |
RTDTempInput |
| 298 |
RTD Temperature Input Data |
| 299 |
BattVolts |
| 300 |
Battery Volts Live Value |
| 301 |
BattVolts Units |
| 302 |
Units for Battery Volts |
| 303 |
BattVolts fmly |
| 304 |
BattVolts Class |
| 305 |
BattVolts PDQ |
| 306 |
BattVolts LS |
| 307 |
BattVolts Fmly stat |
| 308 |
BattVolts USL |
| 309 |
Battery Volts Upper Sensor Limit |
| 310 |
BattVolts LSL |
| 311 |
Battery Volts Lower Sensor Limit |
| 312 |
BattVolts MinSpan |
| 313 |
Battery Volts Minimum Span |
| 314 |
BattVolts Damping |
| 315 |
Battery Volts Damping Value |
| 316 |
BattVolts Update Period |
| 317 |
Battery Volts Update Period |
| 318 |
BattVolts Serial No. |
| 319 |
BattVolts Lower trim |
| 320 |
BattVolts Upper trim |
| 321 |
BattVolts Trim support |
| 322 |
BattVolts Min lower trim |
| 323 |
BattVolts Max lower trim |
| 324 |
BattVolts Min upper trim |
| 325 |
BattVolts Max upper trim |
| 326 |
BattVolts Min trim diff |
| 327 |
BattVolts Simulate |
| 328 |
Battery Volts |
| 329 |
Press |
| 330 |
Temp |
| 331 |
Start Date |
| 332 |
Date AutoXP Was Started |
| 333 |
Start Time |
| 334 |
Time AutoXP Last Started |
| 335 |
RTU Version |
| 336 |
AutoXP Software Version |
| 337 |
.4f |
| 338 |
HART Version |
| 339 |
HART Board Software Version |
| 340 |
#Analog Inputs |
| 341 |
Number of Analog Inputs |
| 342 |
d |
| 343 |
#Smart Inputs |
| 344 |
Number of Smart Xducer Inputs |
| 345 |
#Honey DE Inputs |
| 346 |
Number of Honeywell DE Smart Xducer Inputs |
| 347 |
#Accum Inputs |
| 348 |
Number of Accumulator Xducer Inputs |
| 349 |
#Discrete Inputs |
| 350 |
Number of Discrete Inputs |
| 351 |
#Analog Outputs |
| 352 |
Number of Analog Outputs |
| 353 |
#Discrete Outputs |
| 354 |
Number of Discrete Outputs |
| 355 |
RTC Date |
| 356 |
Current Date |
| 357 |
RTC Time |
| 358 |
Current Time |
| 359 |
AutoXP RTC |
| 360 |
AutoXP RTC Configuration |
| 361 |
Disp Scroll Time |
| 362 |
Integrated LCD Display Scroll Time in Seconds |
| 363 |
s |
| 364 |
Display Contrast |
| 365 |
LCD Display Conrast Setting |
| 366 |
Date Format |
| 367 |
Date Format for Local Display |
| 368 |
MM/DD/YY |
| 369 |
Month/Day/Year |
| 370 |
DD/MM/YY |
| 371 |
Day/Month/Year |
| 372 |
YY/MM/DD |
| 373 |
Year/Month/Day |
| 374 |
DisplayCfg |
| 375 |
AutoXP Display Configuration |
| 376 |
CAL Selection |
| 377 |
Item Selected for Cal |
| 378 |
Command |
| 379 |
DP Manual/Live Input Selection |
| 380 |
Do Nothing |
| 381 |
No Command Required |
| 382 |
Cold Start |
| 383 |
Cold Start AutoXP |
| 384 |
Warm Start |
| 385 |
Warm Start AutoXP |
| 386 |
Rst HART Cfg |
| 387 |
Reset HART Configuration |
| 388 |
Cfg Proccess Vars |
| 389 |
Status Info |
| 390 |
Detailed Setup |
| 391 |
System Info |
| 392 |
System Config |
| 393 |
RTC Config |
| 394 |
Display Config |
| 395 |
Units |
| 396 |
Diff Press |
| 397 |
Live Data |
| 398 |
Manual Config |
| 399 |
Alarm Limits |
| 400 |
Curr. Calibration |
| 401 |
Prev. Calibration |
| 402 |
Pressure |
| 403 |
Device Info |
| 404 |
System |
| 405 |
Device Settings |
| 406 |
Diagnostics |
| 407 |
Maintenance |
| 408 |
Offline |
| 409 |
Operate |
| 410 |
Process Variables |
| 411 |
Output Info |
| 412 |
HART Info |
| 413 |
PV Info |
| 414 |
Cfg Process Vars |
| 415 |
Current Output |
| 416 |
O/P Config |
| 417 |
Test/Cal |
| 418 |
Sys Info |
| 419 |
Edit RTC |
| 420 |
Allows user to edit Time and Date |
| 421 |
AutoXP Command |
| 422 |
Current Calibration |
| 423 |
Calibrate |
| 424 |
ABORT Input Cal |
| 425 |
Handles Input Calibration Aborts |
| 426 |
Calibrate Input |
| 427 |
Perform Analog Input Calibration |
| 428 |
Calibrate DP Input |
| 429 |
Perform DP Input Calibration |
| 430 |
Calibrate Pressure Input |
| 431 |
Perform Pressure Input Calibration |
| 432 |
Calibrate RTD Input |
| 433 |
Perform RTD Temperature Input Calibration |
| 434 |
Handles AutoXP Commands |
| 435 |
PV Analog Channel Saturated |
| 436 |
PV Analog Channel Fixed |
| 437 |
Wireless |
| 438 |
WirelessHART Device |
| 439 |
IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation |
| 440 |
Primary |
| 441 |
Primary Analog Channel |
| 442 |
Secondary |
| 443 |
Secondary Analog Channel |
| 444 |
Tertiary |
| 445 |
Tertiary Analog Channel |
| 446 |
Quaternary |
| 447 |
Quaternary Analog Channel |
| 448 |
Quinary |
| 449 |
Quinary Analog Channel |
| 450 |
Critical Power Failure |
| 451 |
Lock all |
| 452 |
Trim not supported |
| 453 |
Configuration cannot be changed |
| 454 |
Locked by gateway |
| 455 |
Analog Input Channel |
| 456 |
Analog Output Channel |
| 457 |
Secondary Analog Channel Saturated |
| 458 |
Tertiary Analog Channel Saturated |
| 459 |
Quaternary Analog Channel Saturated |
| 460 |
Quinary Analog Channel Saturated |
| 461 |
Secondary Analog Channel Fixed |
| 462 |
Tertiary Analog Channel Fixed |
| 463 |
Quaternary Analog Channel Fixed |
| 464 |
Quinary Analog Channel Fixed |
| 465 |
Simulation active |
| 466 |
The device is in simulation mode and the level output is not representative of the process. |
| 467 |
Non-Volatile memory failure |
| 468 |
The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed. |
| 469 |
Volatile memory error |
| 470 |
The RAM memory check is invalid or maybe corrupt |
| 471 |
Watchdog reset executed |
| 472 |
A watchdog reset has been performed |
| 473 |
Voltage conditions out of range |
| 474 |
A voltage condition is outside its allowable range |
| 475 |
Environmental conditions out of range |
| 476 |
An internal or environmental condition is beyond acceptable limits. |
| 477 |
Electronic failure |
| 478 |
A hardware problem not related to the sensor has been detected. |
| 479 |
Subdevice list changed |
| 480 |
Duplicate master detected |
| 481 |
Capacity Denied |
| 482 |
The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified |
| 483 |
Bandwidth allocation pending |
| 484 |
Block transfer pending |
| 485 |
Battery life |
| 486 |
Percent range |
| 487 |
Loop current |
| 488 |
Primary variable |
| 489 |
Secondary variable |
| 490 |
Tertiary variable |
| 491 |
Quaternary variable |
| 492 |
Read receive time |
| 493 |
Write date and time |
| 494 |
Non-Volatile Clock |
| 495 |
When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure. |
| 496 |
Clock Uninitialized |
| 497 |
The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device. |
| 498 |
None |
| 499 |
No restrictions |
| 500 |
SI Only |
| 501 |
Restricted to SI Unit codes only |
| 502 |
Process automation device |
| 503 |
Discrete device |
| 504 |
Hybrid:Process automation+discrete |
| 505 |
I/O System |
| 506 |
WirelessHART Process automation device |
| 507 |
WirelessHART Discrete device |
| 508 |
WirelessHART Process automation+discrete |
| 509 |
WirelessHART Gateway |
| 510 |
WirelessHART Access point |
| 511 |
WirelessHART Process adapter |
| 512 |
WirelessHART Discrete adapter |
| 513 |
WirelessHART enabled handheld/portable maintenance tool |
| 514 |
Device Profile |
| 515 |
US |
| 516 |
United States of America |
| 517 |
JP |
| 518 |
Japan |
| 519 |
DE |
| 520 |
Germany |
| 521 |
FR |
| 522 |
France |
| 523 |
ES |
| 524 |
Spain |
| 525 |
RU |
| 526 |
Russian Federation |
| 527 |
CN |
| 528 |
People's Republic of China |
| 529 |
Secondary Master |
| 530 |
Primary Master |
| 531 |
Device Diagnostic Status 0 |
| 532 |
Device Diagnostic Status 1 |
| 533 |
I/O and Subdevice Status |
| 534 |
WirelessHART Status |
| 535 |
Time Set Option |
| 536 |
Real Time Clock Flags |
| 537 |
Country |
| 538 |
Country of intended device installation |
| 539 |
SI Unit Control |
| 540 |
Indicates if device should only display SI unit codes |
| 541 |
Time Stamp |
| 542 |
Relative time value on network |
| 543 |
8u |
| 544 |
Dynamic Variables Returned for Device Variables |
| 545 |
Command Response Truncated |
| 546 |
Configuration Change Counter Mismatch |
| 547 |
Status bytes mismatch |
| 548 |
8.3f |
| 549 |
Device Variable |
| 550 |
Variable to trim |
| 551 |
DP Input CAL ABORTED
|
| 552 |
Pressure Input CAL ABORTED
|
| 553 |
RTD Temperature Input CAL ABORTED
|
| 554 |
Warning - This function can affect the device output. Loop should be removed from automatic control.
|
| 555 |
Select No. Cal Points:
|
| 556 |
One Point Cal;Two Point Cal;Three Point Cal |
| 557 |
DP Input |
| 558 |
Pressure Input |
| 559 |
RTD Input |
| 560 |
Supply MIN |
| 561 |
to |
| 562 |
Press OK when Ready |
| 563 |
EU Value:%[f,D]{DiffPressEU_value}
Press OK When Stable |
| 564 |
EU Value:%[f,D]{PressureEU_value}
Press OK When Stable |
| 565 |
EU Value:%[f,D]{RTDTempEU_value}
Press OK When Stable |
| 566 |
Enter New EU Supplied Value
|
| 567 |
fEUZeroVal |
| 568 |
Supply MID |
| 569 |
fEUMidVal |
| 570 |
Supply MAX |
| 571 |
fEUSpanVal |
| 572 |
Updating Calibration.
Please Wait ... |
| 573 |
Calibration Complete
Press OK when Ready |
| 574 |
AutoXP In Write Protect Mode
DP Calibration Aborted |
| 575 |
AutoXP In Write Protect Mode
Presure Calibration Aborted |
| 576 |
AutoXP In Write Protect Mode
RTD Calibration Aborted |
| 577 |
Select Command
|
| 578 |
Do Nothing;COLD Start AutoXP;WARM Start AutoXP;Reset HART Config;Exit |
| 579 |
Warning - AutoXP will RESET and ALL Configuration will be reset to default
Continue? |
| 580 |
Yes;No |
| 581 |
Performing COLD Start.....Please Wait |
| 582 |
Warning - AutoXP will RESET
Continue? |
| 583 |
Performing WARM Start.....Please Wait |
| 584 |
Warning - HART Configuration will be reset
Continue? |
| 585 |
Performing HART Reset.....Please Wait |