| 0 |
%Cs |
| 1 |
SGU15C |
| 2 |
3680 |
| 3 |
Cut Pro |
| 4 |
Cons.Pro |
| 5 |
Thermo MeasureTech |
| 6 |
PMT voltage at max |
| 7 |
Pipe desc -User message to describe the pipe. |
| 8 |
Density of Carrier -The density of the carrier liquid. |
| 9 |
Density of carrier |
| 10 |
Density of Matl -The density of the solid material in the slurry. |
| 11 |
Density of material |
| 12 |
Adapt Damp Status -Control to activate adaptive damping. |
| 13 |
Adapt Damp Status |
| 14 |
Adapt Damp Value -The damping time used when the adaptive damping is active. |
| 15 |
Adapt Damp Value |
| 16 |
Damping Threshold -Percent deviation from last value where the adaptive damping becomes active. |
| 17 |
Damping Threshold |
| 18 |
% |
| 19 |
Process desc -User entered description of process. |
| 20 |
Temp Comp Status -This option turns the temperature compensation on and off. |
| 21 |
Temp Comp Status |
| 22 |
Ref Temp |
| 23 |
Expansion Coef |
| 24 |
Rho1 -The density of the process at the first temperature. |
| 25 |
Rho2 -The density of the process at the second temmperature. |
| 26 |
Temp1 -The temperature at which the first density value is recorded. |
| 27 |
Temp1 |
| 28 |
Temp2 -The temperature at which the second density value is recorded. |
| 29 |
Temp2 |
| 30 |
Zero Value |
| 31 |
Span value |
| 32 |
Last ref -The date on which the last reference was taken on the device. |
| 33 |
Last ref |
| 34 |
Ref hr |
| 35 |
Ref min |
| 36 |
6.0f |
| 37 |
Counts |
| 38 |
Cal Point Number |
| 39 |
#1DENSITY--The density value for the first calibration point. This point is always used for the calibration curve. |
| 40 |
#1DENSITY |
| 41 |
#1SIGNAL--The signal value for the first calibration point. This point is always used for the calibration curve. |
| 42 |
6.4f |
| 43 |
6.6f |
| 44 |
#1SIGNAL |
| 45 |
#2DENSITY--The density value for the second calibration point. This point is always used for the calibration curve. |
| 46 |
#2DENSITY |
| 47 |
g/CuCm |
| 48 |
#2SIGNAL--The signal value for the second calibration point. This point is always used for the calibration curve. |
| 49 |
#2SIGNAL |
| 50 |
#3DENSITY--The density value for the third calibration point. If this calibration point is not used, the density should be set to zero. |
| 51 |
#3DENSITY |
| 52 |
#3SIGNAL--The signal value for the third calibration point. This point is not used if the density for point three is zero. |
| 53 |
#3SIGNAL |
| 54 |
#4DENSITY--The density value for the fourth calibration point. If this calibration point is not used, the density should be set to zero. |
| 55 |
#4DENSITY |
| 56 |
#4SIGNAL--The signal value for the fourth calibration point. This point is not used if the density for point four is zero. |
| 57 |
#4SIGNAL |
| 58 |
#5DENSITY--The density value for the fifth calibration point. If this calibration point is not used, the density should be set to zero. |
| 59 |
#5DENSITY |
| 60 |
#5SIGNAL--The signal value for the fifth calibration point. This point is not used if the density for point five is zero. |
| 61 |
#5SIGNAL |
| 62 |
#6DENSITY--The density value for the sixth calibration point. If this calibration point is not used, the density should be set to zero. |
| 63 |
#6DENSITY |
| 64 |
#6SIGNAL--The signal value for the sixth calibration point. This point is not used if the density for point six is zero. |
| 65 |
#6SIGNAL |
| 66 |
Samp Duration--The time of the sample measurement. The maximum value is 600 seconds. |
| 67 |
Samp Duration |
| 68 |
Density Offset--A value supplied by the user and added to the density value measured. |
| 69 |
Dens Offset |
| 70 |
Temp Comp Input Sensor Type -The type of sensor used to measure temperature. |
| 71 |
Temp Sensor Type |
| 72 |
4 to 20mA |
| 73 |
Temp Comp Units -The units associated with the device used for temperature compensation. |
| 74 |
Units |
| 75 |
Zero Point Value -The zero range point for the temperature transmitter. |
| 76 |
Zero Point Value |
| 77 |
Span Value -The high range point for the temperature transmitter. |
| 78 |
Span Value |
| 79 |
Last setup locatn |
| 80 |
Ref Material -The material selected for the next reference. |
| 81 |
Source Type -The type of source contained in the source housing. |
| 82 |
Date |
| 83 |
2d |
| 84 |
Time-Hrs |
| 85 |
Time-Mins |
| 86 |
5.0f |
| 87 |
PV Units- Engineering unit that the process variable, UPPER_RANGE_VALUE, LOWER_RANGE_VALUE, LOWER_SENSOR_LIMIT, and UPPER_SENSOR_LIMIT will be displayed with. |
| 88 |
PV Units |
| 89 |
Process variable -The density or unit value that is proportional to the output current. It changes as the density of the process material changes. |
| 90 |
4.4f |
| 91 |
Analog Output -The current at the transmitter output whose value changes as the density of the process material. |
| 92 |
PV Output |
| 93 |
2.2f |
| 94 |
PV % of range -A value that is the per cent of full scale. |
| 95 |
USL Upper Sensor Limit -The highest value that the upper range value can be set to. |
| 96 |
USL |
| 97 |
LSL Lower Sensor Limit -The lowest value that the lower range value can be set to. |
| 98 |
LSL |
| 99 |
URV Upper Range Value -The density value that corresponds to 20mA output current. |
| 100 |
URV (@20mA) |
| 101 |
LRV Lower Range Value -The density value that corresponds to 4mA output current. |
| 102 |
LRV (@4mA) |
| 103 |
PV Damp -The time constant of the transmitter. It is used to smooth the output. |
| 104 |
4.1f |
| 105 |
Temp Units |
| 106 |
Temp -The temperature of the process material. This is the temperature used during temperature compensation. |
| 107 |
Temp |
| 108 |
Snsr s/n -A means of identifying each transmitter with a unique number. |
| 109 |
Warning Status Flag |
| 110 |
App Type |
| 111 |
Identifies the process type for API/SGU applications |
| 112 |
Process Type |
| 113 |
Crude Oil |
| 114 |
Gen Refined Prod |
| 115 |
Lube Oil |
| 116 |
Fuel Oil |
| 117 |
Gasoline |
| 118 |
Jet Fuel |
| 119 |
3.2f |
| 120 |
%Cs Auto Cal Span |
| 121 |
.3f |
| 122 |
Pipe ID |
| 123 |
inches |
| 124 |
Cal Point 1 |
| 125 |
Cal Point 2 |
| 126 |
Cal Point 3 |
| 127 |
Cal Point 4 |
| 128 |
Cal Point 5 |
| 129 |
Cal Point 6 |
| 130 |
Not in Ref or Sample mode |
| 131 |
Already in Ref mode |
| 132 |
Already in Sample mode |
| 133 |
Test Device -Directs the 3680 electronics to perform a selftest. Reports any errors that occured. |
| 134 |
Test Device |
| 135 |
Calibration Curve |
| 136 |
New Reference |
| 137 |
New Sample |
| 138 |
RTD |
| 139 |
4 to 20 mA |
| 140 |
None |
| 141 |
Wait for a time |
| 142 |
%Cs (AUTO) |
| 143 |
API (AUTO) |
| 144 |
SGU15C (AUTO) |
| 145 |
%Cs Auto Reference |
| 146 |
%Cs Auto Cal Curve |
| 147 |
API/SGU Auto Ref |
| 148 |
API/SGU Auto Cal |
| 149 |
Valid units check |
| 150 |
Device Setup |
| 151 |
Application Select |
| 152 |
Gen Density (MAN) |
| 153 |
Manual Setup |
| 154 |
Diag/Service |
| 155 |
Calibrate |
| 156 |
%Cs Calibration |
| 157 |
API/SGU Cal |
| 158 |
Calibration |
| 159 |
Reference |
| 160 |
Process Sample |
| 161 |
Basic Setup |
| 162 |
Range and Units |
| 163 |
Date and time |
| 164 |
Damping |
| 165 |
Detailed Setup |
| 166 |
Temp Comp |
| 167 |
Comp Parameters |
| 168 |
Sensor Type |
| 169 |
Output Trim |
| 170 |
REVIEW |
| 171 |
Write Variables |
| 172 |
FMU860 |
| 173 |
DT |
| 174 |
DVC |
| 175 |
FCX |
| 176 |
AS800 |
| 177 |
340T |
| 178 |
340C |
| 179 |
344 |
| 180 |
Siemens Micro K |
| 181 |
SITRANS L |
| 182 |
SIPAN PH |
| 183 |
SITRANS P |
| 184 |
75SMT |
| 185 |
UNIDELTA |
| 186 |
8320 |
| 187 |
SX5100 |
| 188 |
TSV175 |
| 189 |
DMU |
| 190 |
3780 |
| 191 |
BM70 |
| 192 |
8u |
| 193 |
low |
| 194 |
high |
| 195 |
tmp_av |
| 196 |
WARN -Loop should be removed from automatic control |
| 197 |
Testing Xmtr PLEASE WAIT |
| 198 |
Self Test complete Tests PASS |
| 199 |
NOTE-Loop may be returned to automatic control |
| 200 |
Point 1;Point 2;Point 3;Point 4;Point 5;Point 6 |
| 201 |
#%{num}DENSITY %{den} #%{num}SIGNAL %{sig} |
| 202 |
Change Density;Change Signal;Select New Point;End Changes |
| 203 |
#%{num}DENSITY |
| 204 |
den |
| 205 |
#%{num}SIGNAL |
| 206 |
sig |
| 207 |
WARNING--Accepting new calibration curve will reset offset |
| 208 |
Accept Curve;Reject Curve |
| 209 |
New calibration curve rejected |
| 210 |
Making changes permanent. Please Wait... |
| 211 |
ERROR -- Sample being taken |
| 212 |
WARNING -- Reference measurement in progress Please Wait... |
| 213 |
Device may be stuck in reference mode. |
| 214 |
Reference Complete Ref Count %0 |
| 215 |
Accept;Reject |
| 216 |
WARNING--This will reset offset |
| 217 |
Procced;Abort |
| 218 |
Reference Rejected |
| 219 |
Making Changes permanent |
| 220 |
Time Corrupt... |
| 221 |
NOTICE--Reference will take %0 sec |
| 222 |
Start;Exit |
| 223 |
Taking reference measurement. Please Wait... |
| 224 |
Device may be stuck in reference mode. |
| 225 |
Procced;Reject reference |
| 226 |
ERROR -- Reference in progress. |
| 227 |
NOTICE --Sample will take %0 sec |
| 228 |
Taking -- Sample measurement. Please Wait. |
| 229 |
Device may be stuck in sample mode. |
| 230 |
RTD sensor type selected. |
| 231 |
Last calibration was %0 |
| 232 |
Select type of RTD calibration |
| 233 |
Factory;User |
| 234 |
Restoring factory RTD calibration. Please Wait... |
| 235 |
Connect LOW setpoint resistance to RTD input |
| 236 |
Proceed;End |
| 237 |
Enter LOW setpoint resistance value |
| 238 |
Do you wish to correct the problem and try again? |
| 239 |
Yes;No |
| 240 |
LOW setpoint being changed to user calibration. PLEASE WAIT.... |
| 241 |
Low setpoint value accepted. |
| 242 |
Connect HIGH setpoint resistance to RTD input |
| 243 |
Enter HIGH setpoint resistance value |
| 244 |
HIGH Setpoint being changed to user calibration. PLEASE WAIT.... |
| 245 |
High setpoint value accepted. |
| 246 |
4 to 20 mA sensor type selected. |
| 247 |
4 to 20 mA sensor |
| 248 |
Set temp for 4mA;Set temp for 20mA;Trim current input;End |
| 249 |
Enter temperature for 4mA |
| 250 |
Enter temperature for 20mA |
| 251 |
Last trim was %0 |
| 252 |
Select type of temp sensor trim |
| 253 |
Restoring factory trim values. Please Wait... |
| 254 |
Set temp input to 4mA |
| 255 |
Enter input current value |
| 256 |
4mA value being changed to user trimed value. PLEASE WAIT... |
| 257 |
4mA trim value accepted. |
| 258 |
Set temp input to 20mA |
| 259 |
20mA value being changed to user trimed value. PLEASE WAIT... |
| 260 |
20mA trim value accepted. |
| 261 |
No sensor type selected. |
| 262 |
% Consistency
Consult the factory for this application type. |
| 263 |
%Cs Auto Setup
Setting variables to default values for %Cs automatic setup. Please wait... |
| 264 |
%Cs Auto Setup
Enter current date: |
| 265 |
%Cs Auto Setup
Enter current time:
(Hours) |
| 266 |
%Cs Auto Setup
Enter current time:
(Minutes) |
| 267 |
%Cs Auto Setup
Enter Tagname: |
| 268 |
%Cs Auto Setup
Enter desired output
at 4 mA: |
| 269 |
%Cs Auto Setup
Enter desired output
at 20 mA: |
| 270 |
%Cs Auto Setup
Enter Pipe ID: |
| 271 |
%Cs Auto Setup
Starting
%Cs Auto Reference |
| 272 |
%Cs Auto Reference
ERROR -- Sample being
taken |
| 273 |
%Cs Auto Reference
WARNING - Reference measurement in progress
Please Wait... |
| 274 |
%Cs Auto Reference
NOTICE--Reference
will take %0 sec |
| 275 |
%Cs Auto Reference
Ready to run.
Prepare to obtain 3
samples during next
step. |
| 276 |
%Cs Auto Reference
Please wait... |
| 277 |
%Cs Auto Reference
ERROR - Device did not start reference mode. |
| 278 |
%Cs Auto Reference
Taking Reference
measurement.
Obtain 3 samples at
this time. |
| 279 |
%Cs Auto Reference
Device may be stuck
in reference mode. |
| 280 |
%Cs Auto Reference
Determining reference stability.
Please wait ... |
| 281 |
%Cs Auto Reference
Reference stability
inquestion. |
| 282 |
Accept Reference;Re-run Reference;Abort Reference |
| 283 |
%Cs Auto Reference
Reference complete.
Ref Temp: %[.1f]{fRefTemp}Deg C
Ref Count:%{0} |
| 284 |
%Cs Auto Reference
WARNING--This will
reset offset |
| 285 |
%Cs Auto Reference
Making Changes
permanent |
| 286 |
%Cs Auto Reference
Reference Rejected |
| 287 |
%Cs Auto Reference
ERROR - Reference did not complete properly. |
| 288 |
%Cs Auto Cal Curve
Enter Lab result(%Cs)
Ref Temp:%[.1f]{fRefTemp} deg C |
| 289 |
fLabResult |
| 290 |
%Cs Auto Cal Curve
Calculating Curve.
Please wait ... |
| 291 |
Ref temperature out of range for calculations. %Cs Auto Cal Curve will be aborted. |
| 292 |
%Cs Auto Cal Curve
Done: D1= %{fLabResult}
S1= 0
D2= %{fD2Value}
S2= %[.6f]{fS2Value} |
| 293 |
API
Consult the factory for this application type. |
| 294 |
API Auto Setup
Setting variables to default values for API automatic setup. Please wait... |
| 295 |
API Auto Setup
Select Process Type: |
| 296 |
Pipeline;Refinery |
| 297 |
API Auto Setup
Select Pipeline
Application: |
| 298 |
Crude;Gen Refined Prod;Lube Oils |
| 299 |
API Auto Setup
Select Refinery
Application: |
| 300 |
Fuel Oil;Gasoline;Jet Fuel |
| 301 |
API Auto Setup
Enter current date: |
| 302 |
API Auto Setup
Enter current time:
(Hours) |
| 303 |
API Auto Setup
Enter current time:
(Minutes) |
| 304 |
API Auto Setup
Enter Tagname: |
| 305 |
API Auto Setup
Enter desired output
at 4 mA: |
| 306 |
API Auto Setup
Enter desired output
at 20 mA: |
| 307 |
API Auto Setup
Enter Pipe ID: |
| 308 |
API Auto Setup
Starting
%API Auto Reference |
| 309 |
API Auto Reference
ERROR - Sample being
taken |
| 310 |
API Auto Reference
WARNING - Reference measurement in progress
Please Wait... |
| 311 |
API Auto Reference
NOTICE--Reference
will take %0 sec |
| 312 |
API Auto Reference
Ready to run.
Prepare to obtain
sample during next
step. |
| 313 |
API Auto Reference
Waiting for reference to start.
Please wait... |
| 314 |
API Auto Reference
ERROR - Device did not start reference mode. |
| 315 |
API Auto Reference
Taking Reference
measurement.
Obtain sample at
this time. |
| 316 |
API Auto Reference
Device may be stuck
in reference mode. |
| 317 |
API Auto Reference
Reference Complete
Ref Count %0 |
| 318 |
API Auto Ref
WARNING--This will
reset offset |
| 319 |
API Auto Reference
Making Changes
permanent |
| 320 |
API Auto Reference
Reference Rejected |
| 321 |
API Auto Reference
Reference did not complete properly. |
| 322 |
API Auto Cal Curve
Enter Lab result in uncorrected SGU: |
| 323 |
API Auto Cal Curve
Calculating Curve.
Please wait ... |
| 324 |
API Auto Cal Curve
Done: D1= %{fLabResult}
S1= 0.0000
D2= 1.0000
S2= %[.6f]{fS2Value} |
| 325 |
API Auto Cal Curve
Writing curve values
Please wait ... |
| 326 |
SGU15C
Consult the factory for this application type. |
| 327 |
SGU15C Auto Setup
Setting variables to default values for SGU15C automatic setup.
Please wait... |
| 328 |
SGU15C Auto Setup
Select Process Type: |
| 329 |
SGU15C Auto Setup
Select Pipeline
Application: |
| 330 |
SGU15C Auto Setup
Select Refinery
Application: |
| 331 |
SGU15C Auto Setup
Enter current date: |
| 332 |
SGU15C Auto Setup
Enter current time:
(Hours) |
| 333 |
SGU15C Auto Setup
Enter current time:
(Minutes) |
| 334 |
SGU15C Auto Setup
Enter Tagname: |
| 335 |
SGU15C Auto Setup
Enter desired output
at 4 mA: |
| 336 |
SGU15C Auto Setup
Enter desired output
at 20 mA: |
| 337 |
SGU15C Auto Setup
Enter Pipe ID: |
| 338 |
SGU15C Auto Setup
Starting
SGU15C Auto Reference |
| 339 |
SGU15C Auto Reference
ERROR - Sample being
taken |
| 340 |
SGU15C Auto Reference
WARNING - Reference measurement in progress
Please Wait... |
| 341 |
SGU15C Auto Reference
NOTICE--Reference
will take %0 sec |
| 342 |
SGU15C Auto Reference
Ready to run.
Prepare to obtain
sample during next
step. |
| 343 |
SGU15C Auto Reference
Waiting for reference to start.
Please wait... |
| 344 |
SGU15C Auto Reference
ERROR - Device did not start reference mode. |
| 345 |
SGU15C Auto Reference
Taking Reference
measurement.
Obtain sample at
this time. |
| 346 |
SGU15C Auto Reference
Device may be stuck
in reference mode. |
| 347 |
SGU15C Auto Reference
Reference Complete
Ref Count %0 |
| 348 |
SGU15C Auto Reference
WARNING--This will
reset offset |
| 349 |
SGU15C Auto Reference
Making Changes
permanent |
| 350 |
SGU15C Auto Reference
Reference Rejected |
| 351 |
SGU15C Auto Reference
Reference did not complete properly. |
| 352 |
SGU15C Auto Cal Curve
Enter Lab result in uncorrected SGU: |
| 353 |
SGU15C Auto Cal Curve
Calculating Curve.
Please wait ... |
| 354 |
SGU15C Auto Cal Curve
Done: D1= %{fLabResult}
S1= 0.0000
D2= 1.0000
S2= %[.6f]{fS2Value} |
| 355 |
SGU15C Auto Cal Curve
Writing curve values
Please wait ... |
| 356 |
%Cs Auto Reference
NOTICE--Reference
will take %{0} sec |
| 357 |
%Cs Auto Reference
Reference complete.
Ref Temp: %[.1f]{fRefTemperature}Deg C
Ref Count:%{1} |
| 358 |
API/SGU Auto Ref
ERROR -- Sample being
taken |
| 359 |
API/SGU Auto Ref
WARNING - Reference measurement in progress
Please Wait... |
| 360 |
API/SGU Auto Ref
NOTICE--Reference
will take %0 sec |
| 361 |
API/SGU Auto Ref
Ready to run.
Prepare to obtain
sample during next
step. |
| 362 |
API/SGU Auto Ref
Waiting for reference to start.
Please wait... |
| 363 |
API/SGU Auto Ref
ERROR - Device did not start reference mode. |
| 364 |
API/SGU Auto Ref
Taking Reference
measurement.
Obtain sample at
this time. |
| 365 |
API/SGU Auto Ref
Device may be stuck
in reference mode. |
| 366 |
API/SGU Auto Ref
Reference Complete
Ref Count %0 |
| 367 |
API/SGU Auto Ref
WARNING--This will
reset offset |
| 368 |
API/SGU Auto Ref
Making Changes
permanent |
| 369 |
API/SGU Auto Ref
Reference Rejected |
| 370 |
API/SGU Auto Ref
Reference did not complete properly. |
| 371 |
API/SGU Auto Cal
Enter Lab result in uncorrected SGU: |
| 372 |
API/SGU Auto Cal
Calculating Curve.
Please wait ... |
| 373 |
API/SGU Auto Cal
Done: D1= %{fLabResult}
S1= 0.0000
D2= 1.0000
S2= %[.6f]{fS2Value} |
| 374 |
API/SGU Auto Cal
Writing curve values
Please wait ... |
| 375 |
degAPI, %Cs, and SGU15C are not supported by this model of 3680. Units defaulted to SGU. |
| 376 |
degAPI and SGU15C are not supported by this model of 3680. Units defaulted to SGU. |
| 377 |
%Cs is not supported by this model of 3680. Units defaulted to SGU. |