Device dictionary

Loading…

Reference ID	String
0	ND820/T
1	Neles-Jamesbury
2	Exit fixed position
3	Force to 0%
4	Force to 100%
5	To fail-safe pos
6	To anti fail-safe
7	Device is busy
8	Measured value not acceptable
9	Calculated database value not in proper range
10	Bias adjust failed
11	Calibrating
12	Running test
13	Trimming prestage
14	State of ND800
15	The state of field device: normal operation, testing etc.
16	Calibration error
17	Test error
18	Prstg trim err
19	Device status
20	Calibration, test or trim may fail, this variable tells if the failure has occurred
21	RAM error
22	ROM error
23	EEPROM error
24	Watchdog reset
25	Digital HW error
26	Status of digital hardware
27	Current saturation
28	Position saturation
29	Pressure saturation
30	Analog sensor err
31	Status of analog hardware sensors
32	Curr circuit fail
33	Pos meas fail
34	Press meas fail
35	Pilot vlv1 fail
36	Pilot vlv2 fail
37	Analog HW errors
38	Status of analog hardware
39	3.0f
40	%
41	Split range low
42	The split range low limit
43	Split range high
44	The split range high limit
45	Data not acceptable, low limit >= high limit
46	4.1f
47	Supply pressure
48	User given supply pressure
49	Undefined
50	Single acting
51	Double acting
52	Actuator type
53	The type of actuator can be single or double acting
54	Stop
55	Start
56	Prstg trim ctrl
57	Prestage trim control, starts or stops
58	Failure info
59	Stop prestage trim
60	Emergency stop of prestage trim
61	Trim prestage unit
62	Automatic trim of prestage unit
63	W
64
65	PCB S/N
66	The serial number of component board module
67	State can be normal operation, calibratig or running test
68	Normal operation
69	Calibration status
70	Calibration may fail, this variable tells if the failure has occurred
71	No error
72	Position gain
73	Position control gain value. The higher gain results to faster response.
74	5.2f
75	Dead angle comp
76	Control valve dead angle as percent of calibrated valve travel range
77	Pos sensor rot
78	Sets the relationship between the rotation direction of position sensor shaft and valve travel
79	Clockwise opens
80	Clockwise closes
81	Signal direction
82	Sets the relationship between the direction of input signal and valve travel
83	Valve closed at 4 mA
84	Valve open at 4 mA
85	Modification control
86	Set the modification curve use
87	Curve OFF
88	Curve ON
89	Safety range
90	Sets the value of input signal in percent of range at which valve is fully closed
91	Parameter B
92	The actuator type specific feedback parameter B of position control
93	Parameter D
94	The actuator type specific feedback parameter D of position control
95	Activate calibration
96	Set the value to activate position feedback calibration.
97	Normal mode
98	Calibration mode
99	Pos sensor S/N
100	The serial number of position sensor module
101	ND800 S/N
102	The serial number of the ND800 valve controller written into the identification plate
103	Temp compensation
104	Position temperature compensation state
105	Off
106	On
107	Max acttr prs mde
108	Drives actuator into fail-safe position
109	Pressure snsr rnge
110	The linear measurement range of the pressure sensor module
111	Measured prs diff
112	Measured pressure difference
113	5.4f
114	Valve fixed pos
115	Drives valve to a predefined position
116	Pos sensor angle
117	Position sensor angle
118	deg
119	Pos sensor range
120	Position sensor linear range in the degrees of angle
121	ADC bias
122	Target ADC value for biasing
123	Measured temp
124	The measured ambient temperature
125	Temp sensor snstvty
126	Temperature sensor sensitivity value of ND800, see IMO.
127	7.6f
128	Compensation temperature
129	-?-
130	-40 degC
131	-35 degC
132	-30 degC
133	-25 degC
134	-20 degC
135	-15 degC
136	-10 degC
137	- 5 degC
138	0 degC
139	+ 5 degC
140	+10 degC
141	+15 degC
142	+20 degC
143	+25 degC
144	+30 degC
145	+35 degC
146	+40 degC
147	+45 degC
148	+50 degC
149	+55 degC
150	+60 degC
151	+65 degC
152	+70 degC
153	+75 degC
154	+80 degC
155	+85 degC
156	Table code
157	Pos sensor min output
158	Position sensor minimum linear output as percent of supply voltage at corresponding temperature
159	Pos sensor max output
160	Position sensor maximum linear output as percent of supply voltage at corresponding temperature
161	Flow modification point
162	0 %
163	10 %
164	20 %
165	30 %
166	40 %
167	50 %
168	60 %
169	70 %
170	80 %
171	90 %
172	100 %
173	Flow modification value
174	4.2f
175	Event item number
176	Latest event
177	2nd event
178	3rd event
179	4th event
180	5th event
181	6th event
182	7th event
183	8th event
184	9th event
185	10th event
186	11th event
187	12th event
188	13th event
189	14th event
190	15th event
191	16th event
192	17th event
193	18th event
194	19th event
195	20th event
196	Event time
197	6.2f
198	Event code
199	OK
200	Power Error
201	Setpoint Error
202	Calibration OK
203	Position diff. Error
204	Calibration Error
205	Diagnostics Error
206	Position Sensor Error
207	Pressure Sensor Error
208	EEPROM Error
209	Memory Error
210	CPU Error
211	Reset
212	Operation hours
213	Total operation time in hours
214	Valve travel cntr
215	Number of full strokes of valve
216	Valve cycle cntr
217	Number of reversals of valve
218	Act travel cntr
219	Number of full stokes of actuator
220	Act cycle cntr
221	Number of reversals of actuator
222	Input sig
223	The measured current value in the 4-20 mA input signal loop.
224	mA
225	Input signal units
226	Valve trv
227	The measured valve travel as percent of the calibrated valve travel range
228	Valve trv units
229	The units of valve travel
230	Vlv trv SP
231	The valve travel setpoint as percent of the calibrated valve travel range
232	Valve travel SP units
233	The units of valve travel setpoint
234	Act pres
235	The actuator pressure difference in 1- and 2-acting actuators (proportional to actuator load)
236	Pressure units
237	Sets the displayed pressure units
238	Temp
239	The temperature of the device
240	Temperature units
241	Sets the displayed temperature units
242	Foovar
243	8u
244	Warn
245	-WARNING- The positioner will not function properly if the calib sequence failed.
246	Event log
247	View event log
248	Select event log index
249	Event time %{0} hours %{1}
250	View other events?
251	Yes;No
252	Pressure sensor
253	Pressure sensor module calibration
254	Release actuator pressure and check that actuator pressure is equal to air pressure
255	About to set pressure measurement zero
256	Connect actuator supply pressure
257	About to enter maximum actuator pressure mode. WARNING! This causes movement of actuator
258	Select pressure units
259	Enter pressure sensor range (%{0})
260	Enter meter value (%{0})
261	About to set pressure measurement span
262	Please check that the value you entered is reasonable and re-enter the correct value.
263	About to exit maximum actuator pressure mode. WARNING! This causes movement of actuator
264	Pressure sensor module calibration done
265	Position sensor
266	Position sensor module calibration, temperature compensation and identification
267	Enter position sensor serial number
268	Enter position sensor linear range
269	Adjust position sensor to 50% of the sensor linear range (see instructions in IMO)
270	About to set position measurement bias. Check position sensor adjustment
271	Please wait ...
272	About to set temperature compensation data for position sensor
273	Select range of compensation temperature
274	-40 degC to 0 degC;+5 degC to +45 degC;+50 degC to +85 degC
275	Select compensation temperature
276	-40 degC;-35 degC;-30 degC;-25 degC;-20 degC;-15 degC;-10 degC;- 5 degC;0 degC
277	+ 5 degC;+10 degC;+15 degC;+20 degC;+25 degC;+30 degC;+35 degC;+40 degC;+45 degC
278	+50 degC;+55 degC;+60 degC;+65 degC;+70 degC;+75 degC;+80 degC;+85 degC
279	Pos sensor min output at %{0}
280	Pos sensor max output at %{0}
281	Set other temperature values?
282	Position sensor module calibration done
283	Custom linearization
284	Sets customized travel curve of the control valve to linearize the relationship between valve travel setpoint and flow
285	Select valve travel SP
286	0%;10%;20%;30%;40%;50%;60%;70%;80%;90%;100%
287	Set flow linearized valve travel at %{0} travel SP
288	Set other points?
289	Flow linearized valve travel curve set.
290	Temp measurement
291	Temperature ADC zero calibration of the component board module
292	Temperature units
293	About to set temperature measurement ADC zero
294	Temperature measurement calibration done.
295	Input signal
296	Input signal ADC zero and span (4-20mA) calibration of the component board module
297	Adjust loop current to 4 mA
298	About to set input signal ADC zero (4mA)
299	Adjust loop current to 20 mA
300	About to set input signal ADC span (20mA)
301	Input signal ADC calibration done
302	Stop calibration
303	Emergency stop of calibration
304	Calibration stopped.
305	Auto calib travel
306	Automatic calibration of control valve travel against mechanical travel limits corresponding to 0-100% input signal
307	Calibration or test is running. Cannot start calibration.
308	WARNING! Ensure that control valve movement do not disturb process!
309	About to start calibration
310	Calibrating ...
311	Calibration failed. Check positioner.
312	Calibration timeout, possible error in positioner.
313	Calibration done
314	Unit code advise
315	Remember to send a changed unit code to the device!
316	Set ND800 S/N
317	Stores the serial number of the ND800 valve controller into the nonvolatile memory of the ND800. Must be set when component board is replaced
318	Enter ND serial number in format YYYYWWNNNN
319	mfc_nb
320	Incorrect format.
321	Device S/N succesfully set.
322	Reset valve cntrs
323	Resets the valve counters to zero
324	Are you sure?
325	Valve counters reset done.
326	Reset act cntrs
327	Resets the actuator counters to zero
328	Actuator counters reset done.
329	Position transmitter
330	Position transmitter DAC zero and span calibration
331	About to set position transmitter output to 4 mA
332	Output will be set - ok?
333	Is position transmitter output equal to 4 mA?
334	About to set position transmitter output to 20 mA
335	Is position transmitter output equal to 20 mA?
336	Position transmitter calibration done.
337	Hot key
338	Valve Controller
339	Main menu
340	Basic config
341	Cntl valve asmbly
342	Pos cntl tune
343	Detailed config
344	Travel control
345	Flow characteriz
346	Module calib
347	Monitor settings
348	Diagnostics
349	Valve statistics
350	Serial numbers
351	Trim stopped.
352	Calibration, test or trim is running. Cannot trim.
353	Plug the cylinder pressure outputs C1 and C2
354	About to trim
355	Trimming...
356	Trim failed. Check positioner.
357	Trim timeout, possible error in positioner.
358	Trim done
359	Unplug the cylinder pressure outputs C1 and C2
360
Reference ID	String