Device dictionary

Loading…

Reference ID	String
0	TRZ
1	Moore Industries
2	Sensor Error
3
4	Volt
5	Volt.
6	Res.
7	Temp.
8	.2f
9	.1f
10	Unit
11	USL
12	.0f
13	LSL
14	MinSpan
15	Sec.
16	2.f
17	I Out
18	.3f
19	6f
20	% range
21	Range Unit
22	URV
23	7.f
24	LRV
25	7d
26	Sensor
27	input sensor type mV,Ohm,RTD,T/C
28	mV Lo
29	mV Hi
30	mV Lo lin
31	mV Hi lin
32	Ohm Lo
33	Ohm Hi
34	Pot Lo
35	Pot Hi
36	Ohm Lo lin
37	Ohm Hi lin
38	Pot Lo lin
39	Pot Hi lin
40	PT a=3850
41	NI
42	CU
43	T/C B
44	T/C E
45	T/C J
46	T/C K
47	T/C L
48	T/C N
49	T/C R
50	T/C S
51	T/C T
52	T/C U
53	T/C W3
54	T/C W5
55	PT a=3902
56	PT a=3916
57	Local variable. Do not change
58	CJC
59	Wire No.
60	CJC = 0 is internal compensation CJC = 1 is fixed compensation (0degC) CJC 2-3 = 2-3 wires extern compensation
61	Numbers of wires for Ohm/RTD measurement (2-4)
62	RTD value
63	RTD value 25 .. 1000 Ohm
64	4.f
65	Ohm
66	Cable R.
67	Two wire cable compensation 0.0 .. 60.0 Ohm
68	2.2f
69	5.f
70	Under Lim
71	Input under LSL indication 3.60 .. 4.00 mA
72	5f
73	mA
74	Over Lim
75	Input over USL indication 20.00 .. 23.00 mA
76	Sens.Err
77	Sensor breakdown indication, upscale 20.00 .. 23.00 mA , downscale 3.60 .. 4.00
78	Min V
79	Min R
80	Min T
81	Datalogger function, stores min value measured. Value can be cleared (Reset min/max)
82	Max V
83	Max R
84	Max T
85	Datalogger function, stores max value measured. Value can be cleared (Reset min/max)
86	The offset added to the value measured
87	Offs.
88	The offset added to the value measured
89	S.off.
90	The gain is multiplyed to the value measured, (if Unit is degF the zeropoint is 32 degF)
91	S.gain
92	2.4f
93	Offset value too high
94	Offset value too low
95	Gain value too high
96	Gain value too low
97	Offset and gain out of limits
98	Sensor type
99	Select sensor type mv,Ohm,T/C,RTD
100	Reset min/max
101	Resets min/max value measured (datalogger function)
102	Factory trim
103	Factory trim resets the sensor trim offset/gain to factory setting
104	Sensor offset Trim, Calibrate the sensor. The differens between the enteret pressure and the messuret pressure, may max differ 10% of USL-LSL
105	One point trim
106	Sensor offset/gain Trim, Calibrate the sensor. The differens between the enteret pressure and the messuret pressure, may max differ 10% USL-LSL. Hi point should be minmum 10 % larger then low Point
107	Two point trim
108	Main menu
109	Input setup
110	Output setup
111	DataLogger
112	Sensor Trim
113	Quick Access Key
114	FMU860
115	DT
116	DVC
117	FCX
118	AS800
119	340T
120	340C
121	344
122	Siemens Micro K
123	SITRANS L
124	SIPAN PH
125	SITRANS P
126	75SMT
127	UNIDELTA
128	8320
129	SX5100
130	TSV175
131	DMU
132	3780
133	BM70
134	8u
135	Select sensortype
136	RTD;T/C;mV;Ohm;Pot
137	Select RTD type
138	PT a=3850;PT a=3902;PT a=3916;NI;CU
139	Select RTD value
140	Select T/C type
141	B;E;J;K;L;N;R;S;T;U;W3;W5
142	Select mV Low/Hi
143	-10 .. 70mV;-0.1 .. 1.1V
144	Select Ohm Low/Hi
145	0..390 Ohm;0..2200 Ohm
146	Select Pot Low/Hi
147	0 .. 390 Ohm; 0 .. 2200 Ohm
148	Aborting method due to last error
149	Min/max value has been cleared !
150	Sensor trim offset/gain has been reset to factory setting !
151	Apply input value
152	Press OK when input is stable ! PV : %0
153	Enter applied value
154	trim_point
155	Aborting 1 point trim. Offset to large, max 10% of USL-LSL
156	One point trim. ok
157	Apply low input value
158	trim_point_low_true
159	Aborting two point trim. Offset to large, max 10% of USL-LSL
160	Apply hi input value
161	trim_point_hi_true
162	Two point trim. ok
163	Aborting two point trim. span to smal, hi point - low point has to be minimum 0.5% of USL-LSL
Reference ID	String