Device dictionary

Loading…

Reference ID	String
0	MRL700
1	Max Volume required but not entered
2	Unused
3	Tank Vol Setup too complex
4	Window Code must be greater
5	Xmit Update Time must be greater
6	Master Unit has no update time
7	BADFLG3
8	Number of Break Points > 16
9	Data Testing suspended
10	BADFLG2
11	Range Changed after Map Data taken
12	Bad Probe ID
13	Max Level to REF Line < (Absolute Min Distance)
14	BADFLG1
15	No Bad Entries
16	Range Changed after Clutter Data (Collection)
17	Meas 1 is not Level or Distance
18	# of Averages Too Big
19	BADFLG0
20	DSP Program Error
21	DSP Data Error
22	DSP Clutter Error
23	Sweep Control (problem)
24	Signal Processor Failed
25	Radar Head Failed
26	DSP Task Failed
27	AFW8
28	No Rate Channel specified
29	Meas for Rate must be less
30	Brktab Range Error
31	BADFLG4
32	Polling Address
33	Response Preambles
34	Burst Command
35	Process Alarm 9
36	Process Alarm 10
37	Process Alarm 11
38	Process Alarm 12
39	Process Alarm 13
40	Process Alarm 14
41	Process Alarm 15
42	Process Alarm 16
43	AFW3
44	Process Alarm 1
45	Process Alarm 2
46	Process Alarm 3
47	Process Alarm 4
48	Process Alarm 5
49	Process Alarm 6
50	Process Alarm 7
51	Process Alarm 8
52	AFW2
53	Buffer Full
54	Current max or min
55	Power has been off
56	Hold(s) are active
57	Alternate Time Constant
58	Output on alternate measurement
59	Keypad in use
60	AFW1
61	Range Gate not captured
62	No Signal Processor!
63	Lost communication with MRL700
64	Wrong Gage Connected
65	Probe ID Required
66	Hart board checksum error
67	AFW0
68	MSG overrun
69	DSP Config Error
70	DSP Assert (Program Memory Address)
71	Prb ID Override
72	FBUFFER Overrun
73	NV Data Changed
74	AFW9
75	Current under min
76	RAM Memory Error
77	PROM Checksum Error
78	P_MEM Checksum Error
79	Pri-NV Checksum Error
80	Sec_NV Checksum Error
81	NV RAM failed
82	NV Write Error
83	AFW6
84	Current over max
85	NV Erase failed
86	NV Checksum Error
87	Sweep Start Required
88	AFW5
89	Waiting for Echo
90	Echo is Lost
91	Waiting for Good Echo
92	Signal Saturated
93	Volt Marker Fault
94	System Fault
95	AFW4
96	Relay 1
97	Relay 2
98	Alarm Point 1
99	Alarm Point 2
100	Alarm Point 3
101	Alarm Point 4
102	Alarm Point 5
103	Alarm Point 6
104	Alarm Point 7
105	Alarm Point 8
106	Alarm Point 9
107	Alarm Point 10
108	Alarm Point 11
109	Alarm Point 12
110	Alarm Point 13
111	Alarm Point 14
112	Alarm Point 15
113	Alarm Point 16
114	Measurement 1
115	Measurement 2
116	Measurement 3
117	Measurement 4
118	Measurement 5
119	Measurement 6
120	Measurement 7
121	Measurement 8
122	Alarm Assign 1
123	Alarm Assign 2
124	Alarm Assign 3
125	Alarm Assign 4
126	Alarm Assign 5
127	Alarm Assign 6
128	Alarm Assign 7
129	Alarm Assign 8
130	Alarm Assign 9
131	Alarm Assign 10
132	Alarm Assign 11
133	Alarm Assign 12
134	Alarm Assign 13
135	Alarm Assign 14
136	Alarm Assign 15
137	Alarm Assign 16
138	Output Measurement
139	Process variable -The level/distance or unit value that is proportional to the output current. It changes as the level of the process material changes.
140	4.3f
141	Analog Output -The current at the transmitter output whose value changes as the level of the process material.
142	PV Output
143	2.2f
144	PV % of range -A value that is the per cent of full scale.
145	Measure Units
146	4.1f
147	Signal Time Constant
148	4.0f
149	Agitator Time Constant
150	5.3f
151	Global Weight Fact
152	6.3f
153	Enable NV section
154	Locked
155	Unlocked
156	# Measurements
157	Antenna ID Code:
158	5d
159	Seal Offset
160	Sweep Start
161	13.3E
162	13.4E
163	USL
164	LSL
165	4.4f
166	Snsr s/n -A means of identifying each transmitter with a unique number.
167	Alarm Mode Flags
168	Relay Number
169	Relay 1 State On Alarm
170	On
171	Off
172	Relay 2 State On Alarm
173	Relay 1 Latching Mode
174	Relay 2 Latching Mode
175	Number of Relays
176	Relay Option
177	No
178	Yes
179	Max Current
180	.2f
181	Min Current
182	Out Hold Point
183	.3f
184	Correction @MAX
185	Correction @MIN
186	Device Command
187	Alarm Assign Index
188	Device Name
189	Device S/W Rev
190	Level Units
191	NVRAM Clear Flag
192	Measurement Number
193	Other Measurement Number
194	Meas Type
195	Inactive
196	Distance
197	Level
198	% Distance
199	% Level
200	Signal strength
201	Units
202	Value
203	URV
204	LRV
205	Rate Units
206	Rate Meas #
207	Rate Min Change
208	Rate Smooth
209	4.2f
210	Alarm Set Cmd 1
211	Do nothing
212	Hold AO at HOLD val
213	Hold AO at max val
214	Hold AO at min val
215	Clear all holds
216	Hold AO at FAULT HI
217	Hold AO at FAULT LOW
218	Alarm Clr Cmd 1
219	Alarm Set Cmd 2
220	Alarm Clr Cmd 2
221	Alarm Set Cmd 3
222	Alarm Clr Cmd 3
223	Alarm Point Number
224	#1SetPoint
225	#1ClearPoint
226	#1Alarm Clear
227	Clear Point
228	Deadband
229	#1Alrm Set Action
230	Nothing
231	Set AO to FAULT LOW
232	Set AO to FAULT HIGH
233	Exec Alarm Cmd 1
234	Exec Alarm Cmd 2
235	Exec Alarm Cmd 3
236	#2SetPoint
237	#2ClearPoint
238	#2Alarm Clear
239	#2Alrm Set Action
240	#3SetPoint
241	#3ClearPoint
242	#3Alarm Clear
243	#3Alrm Set Action
244	#4SetPoint
245	#4ClearPoint
246	#4Alarm Clear
247	#4Alrm Set Action
248	#5SetPoint
249	#5ClearPoint
250	#5Alarm Clear
251	#5Alrm Set Action
252	#6SetPoint
253	#6ClearPoint
254	#6Alarm Clear
255	#6Alrm Set Action
256	#7SetPoint
257	#7ClearPoint
258	#7Alarm Clear
259	#7Alrm Set Action
260	#8SetPoint
261	#8ClearPoint
262	#8Alarm Clear
263	#8Alrm Set Action
264	#9SetPoint
265	#9ClearPoint
266	#9Alarm Clear
267	#9Alrm Set Action
268	#10SetPoint
269	#10ClearPoint
270	#10Alarm Clear
271	#10Alrm Set Action
272	#11SetPoint
273	#11ClearPoint
274	#11Alarm Clear
275	#11Alrm Set Action
276	#12SetPoint
277	#12ClearPoint
278	#12Alarm Clear
279	#12Alrm Set Action
280	#13SetPoint
281	#13ClearPoint
282	#13Alarm Clear
283	#13Alrm Set Action
284	#14SetPoint
285	#14ClearPoint
286	#14Alarm Clear
287	#14Alrm Set Action
288	#15SetPoint
289	#15ClearPoint
290	#15Alarm Clear
291	#15Alrm Set Action
292	#16SetPoint
293	#16ClearPoint
294	#16Alarm Clear
295	#16Alrm Set Action
296	Units Mask
297	All
298	English
299	Metric
300	Level/Dist Units
301	Primary Meas Type
302	PV Units
303	PV
304	Max Distance
305	7.3f
306	Offset
307	Zero Level
308	Max Level
309	Max Level Dist
310	Lower range value
311	Upper range value
312	Max echoes processed
313	Min Sig Stength
314	Succ. wt. factor
315	Echo Distance
316	Report echo number
317	Echo Sig strength
318	5.2f
319	Number of report echoes
320	Echo Report Options
321	Next
322	Previous
323	Exit
324	Echo Sample
325	Bad units
326	Invalid Item Number
327	Invalid command number
328	Current Output
329	Alarm Cmd Execute
330	Alrm Meas Assign
331	System Restart
332	Erase All Entries
333	Clear All Alarms
334	Clear All Holds
335	View Other Meas
336	Device Status
337	Alarm Setup
338	Setup
339	Resp Time Setup
340	False Echo Tools
341	Measure Head Setup
342	Echo Report
343	Assign & Modify
344	REVIEW
345	Device vars
346	Xmtr Vars
347	Output vars
348	Radar vars
349	Relay Vars
350	Measurement vars
351	Alarm Vars
352	Prim Meas vars
353	Gen Alarm Vars
354	Alarm1 Vars
355	Alarm2 Vars
356	Alarm3 Vars
357	Alarm4 Vars
358	Alarm5 Vars
359	Alarm6 Vars
360	Alarm7 Vars
361	Alarm8 Vars
362	Alarm9 Vars
363	Alarm10 Vars
364	Alarm11 Vars
365	Alarm12 Vars
366	Alarm13 Vars
367	Alarm14 Vars
368	Alarm15 Vars
369	Alarm16 Vars
370	Device Setup
371	MRL700 Setup & Cal
372	Radar Fine Tuning
373	Main Measurement
374	Outputs & Alarms
375	Actions
376	Other Measurements
377	Diag/Service
378	Device Info
379	HART Variables
380	FMU860
381	DT
382	DVC
383	FCX
384	AS800
385	340T
386	340C
387	344
388	Siemens Micro K
389	SITRANS L
390	SIPAN PH
391	SITRANS P
392	75SMT
393	UNIDELTA
394	8320
395	SX5100
396	TSV175
397	DMU
398	3780
399	BM70
400	8u
401	WARNING - This function can affect the device output. Loop should be removed from automatic control.
402	CURRENT OUTPUT SETUP Maximum current output:
403	CURRENT OUTPUT SETUP Minimum current output:
404	CURRENT OUTPUT SETUP Measurement number used for normal mode current output:
405	CURRENT OUTPUT SETUP Current output hold mode value (% of scale):
406	NOTE-Loop may be returned to automatic control
407	ALARM CMD EXECUTE Alarm action for #1 ALM SET is command:
408	ALARM CMD EXECUTE Alarm action for #1 ALM CLR is command:
409	ALARM CMD EXECUTE Alarm action for #2 ALM SET is command:
410	ALARM CMD EXECUTE Alarm action for #2 ALM CLR is command:
411	ALARM CMD EXECUTE Alarm action for #3 ALM SET is command:
412	ALARM CMD EXECUTE Alarm action for #3 ALM CLR is command:
413	ALARM MEAS ASSIGNMENT Alarm %{nAlarm} measurement assignment: %{0}
414	Next Alarm;Change assignment;Exit
415	ALARM MEAS ASSIGNMENT Alarm %{nAlarm} measurement assignment (1 - %{1}):
416	nAlarmMeas
417	ALARM MEAS ASSIGNMENT Invalid measurement selection.
418	WARNING - This function will affect the device output. Loop should be removed from automatic control.
419	Waiting for device to reset. Please wait ...
420	NOTE-After the MRL700 has restarted, the loop may be returned to automatic control.
421	Setting all MRL700 variables to their default values. Please wait ...
422	You must now turn the handheld off and then back on to complete the MRL700 erase operation.
423	NOTE-Loop may be returned to automatic control after the MRL700 variables have been set to the desired values.
424	NOTE-Loop may be returned to automatic control.
425	There are %{nOtherMeasurements} other measurements setup. Enter measurement to view (2 - %{0}):
426	nMeasurement
427	MEASUREMENT VIEW Invalid measurment selection. Value must be between 2 and %0.
428	MEASUREMENT VIEW There are no other measurements configured.
429	MEASUREMENT VIEW Measurement #%{nMeasurement} Type: %3 Value: %{1} %{2}
430	Select Other Meas;Exit
431	MEASUREMENT VIEW Measurement #%{nMeasurement} Type: Unknown Value: %{1} ?
432	low
433	high
434	Setting output to minimum current value
435	Setting output to maximum current value
436	Aborting method due to last error
437	All status information has been displayed.
438	ALARM SETUP Select alarm number to set up (1 - 16):
439	nAlarm
440	Invalid alarm selection. Value must be from 1 to 16.
441	ALARM SETUP Alarm %{nAlarm} set point: (units = %{2})
442	ALARM SETUP Alarm %{nAlarm} clear mode:
443	ALARM SETUP Alarm %{nAlarm} Clear Point: (units = %{2})
444	ALARM SETUP Alarm %{nAlarm} Deadband: (units = %{2})
445	ALARM SETUP Alarm %{nAlarm} Set Action:
446	ALARM SETUP Relay option not installed. Please make an alternate selection.
447	ALARM SETUP Alarm %{nAlarm} Relay State on alarm:
448	SETUP Primary Measurement:
449	DISTANCE SETUP The eng unit setting is not in the Distance units set and will be defaulted to Feet.
450	LEVEL SETUP The eng unit setting is not in the Level units set and will be defaulted to Feet.
451	SETUP Eng Units selection:
452	DISTANCE SETUP Distance REF LINE to zero distance point (%[.3f]{1} Min):
453	DISTANCE SETUP REF LINE to max distance measured (%[.3f]{0} Max):
454	DISTANCE SETUP Distance reading for %[.2f]{2} mA output:
455	DISTANCE SETUP Distance reading for %[.2f]{3} mA output:
456	LEVEL SETUP Distance REF LINE to zero level point (%[.3f]{4} Max):
457	LEVEL SETUP Maximum level (%[.3f]{0} Max):
458	LEVEL SETUP Note: level readout not correct without zer level point & max level.
459	LEVEL SETUP Level reading for %[.2f]{2} mA output:
460	LEVEL SETUP Level reading for %[.2f]{3} mA output:
461	RESP TIME SETUP Distance Signal Time Constant value:
462	RESP TIME SETUP Level Signal Time Constant value:
463	RESP TIME SETUP Agitator Reject Time Constant value:
464	RESP TIME SETUP Weighting factor (GWF) for echoes inside range gate:
465	FALSE ECHO TOOLS Echo amplitude successive weighting factor (SWF):
466	FALSE ECHO TOOLS Minimum allowable signal strength:
467	FALSE ECHO TOOLS Max echo count to be processed:
468	MEASURE HEAD SETUP Flange mounted seal velocity correction:
469	MEASURE HEAD SETUP Enable protected NV section:
470	MEASURE HEAD SETUP Sweep start: %{0}
471	MEASURE HEAD SETUP Sweep start:
472	MEASURE HEAD SETUP Antenna ID Code:
473	Checking antenna database. Please wait ...
474	MEASURE HEAD SETUP Antenna code accepted!
475	MEASURE HEAD SETUP Warning : Antenna code entered is not in database!
476	Echo %{nEchoNum} of %{nTotEchoReport} (%{0}) Distance: %{2} %{3} Sig Str: %{1}
477	Next;Previous;Exit
478	There are no echoes to report!
479	There are %{nOtherMeasurements} other measurements configured. Select desired action:
480	New Measurement;Modify Existing;Exit
481	Modify Existing;Exit
482	There are no other measurements configured. Select desired action:
483	New Measurement;Exit
484	Creating new measurement #%{nMeasurement} Please wait ...
485	MEASUREMENT SETUP Reading represented by measurement %{nMeasurement} is:
486	MODIFY MEASUREMENT Enter measurement to modify (2 - %{nLastMeasurement}):
487	Measurement %{nMeasurement} type configured in the device not supported in MRL700 HART.
488	Keep meas type;Change type
489	Invalid measurement selection.
490	MEASUREMENT SETUP Measurement %{nMeasurement} units:
491	LEVEL SETUP Note: level readout not correct without zero lev point & max level.
492	Measurement type unknown - Exiting.
493	MEASUREMENT SETUP The eng unit setting is not in the Distance units set and will be defaulted to Feet.
494	MEASUREMENT SETUP The eng unit setting is not in the Level units set and will be defaulted to Feet.
495	Meas #%{nMeasurement} reading for high end value:
496	Meas #%{nMeasurement} reading for low end value:
Reference ID	String