Device dictionary

Loading…

Reference ID	String
0	O2_4100e
1	METTLER
2	Address
3	Tag
4	Descriptor
5	Message
6	Date
7	Assembly Num
8	Error Status
9	Field Device Error Status- Failure messages of the Field Device are listed
10	Err 01 SAT Value
11	Err 02 Conc Val
12	Err 03 Temp Val.
13	Err 11 I < 3.8mA
14	Err 12 I >20.5mA
15	Err 13 Loop Span
16	Err 98 Conf Data
17	Err 99 Data Lost
18	Smiley Earnest
19	Smiley Earnest - Maintance required. Sensoface provides information on wear and required maintance. However, device continues operation with diminished accuracy.
20	Response time
21	Cal. timer > 80%
22	Zero point
23	Slope
24	Smiley Sad
25	Smiley Sad - Correct measurment is no longer ensured. Sensoface provides information on wear and required maintance. However, device continues operation with seriously diminished accuracy.
26	Response time
27	Cal. timer >100%
28	Err 33
29	Zero point limit
30	Slope limit
31	Temp SAT/Conc
32	Analog Out Sat.
33	HOLD Mode
34	Analog Outputs of the Field Device are fixed in HOLD mode. The analog and digital Outputs remain unchanged.
35	Resp. Preambles
36	Device Status
37	Device status and mode
38	Configuration
39	Calibration
40	Sample was taken
41	Online
42	Process Variables
43	Diagnosis
44	Device Info
45	Conf: Output
46	Conf: Temp. Comp.
47	Conf: Correction
48	Conf: Calibration
49	Conf: Alarm Setup
50	Service
51	Review
52	Review: Conf/Cal
53	Review: Dev. Info
54	Upload Variables
55	Dummy1Byte
56	Dummy4Byte
57	Sel. Code Index
58
59	Sel. Codes
60	Input Sel. Code
61	Calib. Sel. Code
62	Output Sel. Code
63	Temp Sel. Code
64	Conf.4 Sel. Code
65	Invalid Unit Code
66	Busy
67	22mA on Error
68	Switch 22mA signal for error message on or off
69	Off
70	On
71	HOLD Last/Fix
72	The output current behavior in the HOLD mode can be specified. Last- The output current is frozen at its last value, Fix- A constant value from 3.8mA to 22mA
73	Last Value
74	Fixed Current
75	Sensocheck
76	Sensocheck continously monitors the sensor
77	Alarm LED Hold
78	Alarm LED Hold: Para. Alarm Hold ------------------ on : on flash off : flash off
79	PV unit
80	Select the PV Unit
81	%
82	µg/l
83	g/l
84	ppb
85	ppm
86	meas function
87	DO
88	GAS
89	sensor type
90	Typ A
91	Typ B
92	press medium
93	BAR
94	KPA
95	PSI
96	cal mode
97	Conc
98	Sat
99	Temp. unit
100	°C
101	°F
102	Sensor
103	NTC22k
104	NTC30k
105	PV Unit
106	ugl
107	5.3f
108	5.2f
109	5.5f
110	4.0f
111	5.1f
112	PV USL
113	PV LSL
114	Min. Span
115	PV AO
116	mA
117	4.1f
118	PV %
119	You can choose the kind of dependence of the current from the digital value
120	7.5f
121	Number
122	SV
123	Temperature of process medium temperature compensation
124	5.0f
125	SV USV
126	SV LSV
127	SAT
128	Percent Saturation value
129	4.2f
130	Concentration value
131	Temp.
132	Temperature for process medium temperature compensation
133	Sensor input current
134	Press(mbar)
135	The Preasure for measurement in mbar
136	3.1f
137	Pressure (cal)
138	The Preasure for calibration
139	mbar
140	The Calibration generates the electrode parameters. You can also directly enter the slope of an electrode
141	8.6f
142	Cal.Timer
143	Calibration timer interval. 0 = cal time switched off
144	h
145	04.0f
146	Cal. Mode
147	Selected Calibration Mode
148	Sal. Corr
149	Salinity correction ppt(parts per thousand) - corresponds to g/kg
150	rel. humidity
151	relative humidity
152	02.0f
153	2.0f
154	HOLD Fix Value
155	Specify fixed output current in HOLD mode
156	pol.volt
157	polarisation voltage for sensor
158	mV
159	Sample
160	Calibration with Sampling to determine the electrode zero point
161	Output Filter
162	Time constant of output filter
163	s
164	3.0f
165	Alarm Delay
166	Alarm delay time of alarm signal
167	Filtertime of output current
168	Pressure
169	Select the Pressure-Unit and enter the Pressure-value
170	Self Test
171	Performs transmitter self test
172	Master Reset
173	Performs master reset in the Field Device
174	Conf Changed Reset
175	Performs reset of configuration changed sign in the Field Device
176	Loop Test
177	Take Sample
178	Sample Calibration Sequence Take Sample
179	Input Lab Sample
180	Sample Calibration Sequence Input Lab Sample
181	FMU860
182	DT
183	DVC
184	FCX
185	AS800
186	340T
187	340C
188	344
189	Siemens Micro K
190	SITRANS L
191	SIPAN PH
192	SITRANS P
193	75SMT
194	UNIDELTA
195	8320
196	SX5100
197	TSV175
198	DMU
199	3780
200	BM70
201	8u
202	Sample calibration via HART not available for device software before V1.0. Press OK to finish
203	WARNING: Configuration was abborted! ACTION: Repeat this step.
204	Select Press Unit:
205	Enter Pressure:
206	Press OK to perform transmitter self test
207	Self test is running please wait: %{sec} s
208	Press OK to perform master reset
209	Master reset is running please wait: %{sec} s
210	Press OK to reset configuration changed sign
211	Take a sample from the process and store the currently measured value.
212	Note that the meassured value of the sample is temperature dependent.
213	As far as possible, you should transport the sample in an insulated container (Dewar).
214	The meassured value may also be altered due to escaping of volatile substances.
215	WARNING: Device is in calibration or configuration, no sample calibration allowed!
216	ACTION: Leave device calibration or configuration and repeat this step.
217	WARNING: Sample was already taken. If you call <Take Sample> twice then the first sample will be lost!
218	ACTION: Confirm discarding the first sample. Press OK to discard the first sample.
219	Last measured value: %{0} %{1} %{2} %{3} Press OK to take calibration sample
220	WARNING: Sample calibration was abborted! ACTION: Repeat this step.
221	Enter the measured lab value. The new zero point is automatically calculated and stored.
222	The values obtained by sample calibration are always accepted, even if they are outside calibration limits!
223	WARNING: No sample was taken, no sample calibration allowed!
224	ACTION: First call <Take Sample> and then <Input Lab Sample>.
225	Enter the comparison lab value :
Reference ID	String