Device dictionary

Loading…

Reference ID	String
0	Model TA2
1	MAGNETROL
2	Device ID
3	Poll Address
4	Error/Warnings
5	Usr Params Reset
6	User Parameters Reset - The application configuration information has been reset. Please reconfigure the instrument under Basic Set Up.
7	Prb Params Reset
8	Probe Parameters Reset - Re-enter the probe calibration data under Cal Factors using the probe password.
9	Module Cal Req'd
10	Module Calibration Required - The TA2 electronics require re-calibration by Magnetrol. The instrument will continue to operate at reduced accuracy.
11	Total Data Lost
12	Totalizer Data Lost - Data in the Totalizer has been lost. Reset the totalizer.
13	No Probe Signals
14	No Probe Signals - Check Probe condition under Diagnostics, Probe Status. Check probe wiring.
15	Probe Hdwe Fault
16	Probe Hardware Fault - Check Probe condition under Diagnostics, Probe Status. Check probe wiring.
17	Initializing TA2
18	Initializing - The TA2 is going through initialization. Flow measurement will begin after completion of the initialization.
19	Fixed Signl Mode
20	Fixed Signal Mode Active - The TA2 is not providing a signal based upon PV. This will only occur if the local display is being utilized in diagnostic mode or if the TA2 is in Gas Calibrate Mode.
21	PV is
22	Adjust Loop Current
23	Loop Test
24	Velocity
25	Units
26	Loop
27	Flow
28	Mass
29	Temperature
30	Totalizer
31	Mode
32	Gas Temp
33	Total
34	Velocty
35	Density
36	Diameter
37	Area
38	Install Factor -
39	A
40	B
41	C
42	Cal Coeff -
43	Gas Coeff -
44	Ag
45	Bg
46	Cg
47	Dg
48	Eg
49	Velocity - Mass velocity is corrected to STP conditions.
50	SF/M
51	Standard feet per minute.
52	SF/S
53	Standard feet per second.
54	Nm/s
55	Normal meters per second.
56	Flow - Select the units of measurement for the mass volumetric flow rate.
57	SCFM
58	Standard cubic feet per minute.
59	Nm3/h
60	Normal cubic meters per hour.
61	Nl/h
62	Normal liters per hour.
63	Mass - Select units of measurement.
64	lbs/H
65	lbs/M
66	kg/h
67	kg/m
68	Temperature - Select units of measurement for temperature.
69	F
70	Totalized Flow
71	Totalizer - Select units of measurements used by the Totalizer.
72	SCF
73	Standard cubic feet.
74	Nm3
75	Normal cubic meters.
76	Nl
77	Normal liters.
78	lbs
79	kg
80	Diameter - Select the desired units of measurement for measuring the inside diameter of a circular pipe or duct.
81	inches
82	feet
83	mm
84	meters
85	Area - Select units of measurement used for the flow area of the pipe or duct.
86	in2
87	Square inches.
88	ft2
89	Square feet.
90	m2
91	Square meters.
92	mm2
93	Square milimeters.
94	Density - Select units of measurement for density at STP or Normal conditions.
95	lb/ft3
96	kg/m3
97	kg/l
98	STP Pressure
99	STP Pressure - Permit the user to modify STP conditions to application specific requirements. Select Standard Pressure of 1 atmosphere (14.7 psia) or 1 bar (14.5 psia).
100	1 Atmosphere
101	1 Bar
102	Volume Flow
103	.0f
104	Mass Flow
105	Gas Temperature
106	.2f
107	Total - Displays the total flow over the elapsed time since the totalizer was last re-set.
108	Minimum Span
109	Damping
110	Damping - Adds additional time delay to the TA2. Enter value as a time constant from 0 to 15 seconds.
111	4.1f
112	Lower Xducer Limit
113	Lower Xducer Limit - Probe calibration factor, flow rates less than this value are outside the original calibration range.
114	Upper Xducer Limit
115	Upper Xducer Limit - Probe calibration factor, flow rates exceeding this value are outside the original calibration range.
116	Zero Flow Signal
117	Zero Flow Signal - Probe calibration factor.
118	mW
119	PV Loop
120	5.2f
121	Fault State
122	Fault State - Select how the Analog output of the TA2 will respond if a fault in the instrument is detected.
123	3.6mA
124	22mA
125	Hold
126	4mA Set Point
127	4mA Set Point - Enter the 4 mA point using the units of measurement previously selected.
128	20mA Set Point
129	20mA Set Point - Enter the 20 mA point using the units of measurement previously selected.
130	% Output
131	%
132	Pipe ID
133	Pipe Inside Diameter - The flow area must be entered. This is done by either entering the inside diameter of a pipe or the cross sectional area of the pipe or duct.
134	.4f
135	Flow Area
136	Flow Area - The flow area must be entered. This is done by either entering the inside diameter of a pipe or the cross sectional area of the pipe or duct.
137	Mode - Enable or Disable the totalizer operation.
138	Disabled
139	Enabled
140	Elapsed Time
141	Elapsed Time - Displays the elapsed time in hours since the totalizer was last re-set.
142	.1f
143	hours
144	Low Flow Cutoff
145	Low Flow Cutoff - velocity values less than the entered values will not be detected. This is useful if flow is detected when a no flow condition exists.
146	Date/Time/Initials
147	Date/Time/Initials - When and by whom calibration was performed.
148	Magnetrol S/N
149	Magnetrol S/N - Serial number of this unit.
150	Signal
151	Signal/PV - Displays the signal and the corresponding value of the PV. May be useful for diagnostics.
152	Firmware Version
153	Firmware Version - Provides the version of the Firmware and the date used by the TA2.
154	4mA Trim Value
155	4mA Trim Value - Factory parameter, displayed for diagnostic purposes only.
156	4u
157	20mA Trim Value
158	20mA Trim Value - Factory parameter, displayed for diagnostic purposes only.
159	Change Password
160	User password required to change parameter settings from keypad.
161	Delta T
162	Delta T - Displays the set point temperature which the TA2 is controlling. Useful for diagnostics information.
163	Temp Sensor
164	Temp Sensor - Provides status of the Temperature sensor in the TA2. Will display either OK, Shorted, or Open.
165	OK
166	Shorted
167	Open
168	Unknown
169	Flow Sensor
170	Flow Sensor - Provides status of the Flow sensor in the TA2. Will display either OK, Shorted, or Open.
171	Probe Heater
172	Probe Heater - Provides status of the Probe Heater in the TA2. Will display either OK, Shorted, or Open.
173	Heater Setting
174	Heater Setting - Displays a value for the heater setting. Useful for diagnostics information.
175	5u
176	Install Factors - A, B, C; Install Factors are utilized in situations when the measured flow rate may need to be adjusted due to variations in flow profile or other installation factors. The Install Factors are the coefficients of the polynomial equation: Corrected Flow = A + Bv + Cv^2 where v is the velocity measured by the TA2.
177	.6f
178	A - Probe calibration factor.
179	.5f
180	B - Probe calibration factor.
181	C - Probe calibration factor.
182	STP Temperature
183	STP Temperature - permit the user to modify STP conditions to application specific requirements. Enter temperature used for Standard Temperature.
184	Ro
185	Ro - Probe calibration factor.
186	Fo
187	Fo - Probe calibration factor.
188	TCC-A
189	TCC-A - Calibration factor.
190	TCC-B
191	TCC-B - Calibration factor.
192	Density - Gas density at user STP conditions.
193	Gas Calibrate Mode
194	Gas Calibration Mode - Factory calibration mode. This mode should only be enabled after direction from Magnetrol.
195	Ag - Calibration factor.
196	Bg - Calibration factor.
197	Cg - Calibration factor.
198	Dg - Calibration factor.
199	Eg - Calibration factor.
200	Coeff Ratio
201	Coeff Ratio - Factory calibration parameter.
202	Set Point
203	Set Point - Factory calibration parameter.
204	Slope
205	Slope - Factory calibration parameter.
206	Power Predictor
207	Power Predictor - Factory calibration parameter.
208	Exception Code
209	Exception Code - Factory parameter, displayed for diagnostic purposes only.
210	3u
211	Enter Password
212	Password is required to change calibration factors, refer to calibration certificate.
213	Main Menu
214	Device Setup
215	Basic Setup
216	System Units
217	Variable Selection
218	Advanced Setup
219	Install Factors
220	STP Conditions
221	Diagnostics
222	Signal/PV
223	Probe Status
224	Cal Factors
225	Probe Parameters
226	Calibration Coeff
227	Gas Parameters
228	Gas Coefficients
229	Control Parameters
230	Device Description
231	Review
232	Reset Total
233	Reset Total - Resets the totalizer and elapsed time to 0.
234	FMU860
235	DT
236	DVC
237	FCX
238	AS800
239	340T
240	340C
241	344
242	Siemens Micro K
243	SITRANS L
244	SIPAN PH
245	SITRANS P
246	75SMT
247	UNIDELTA
248	8320
249	SX5100
250	TSV175
251	DMU
252	3780
253	BM70
254	8u
255	Are You Sure?
256	No;Yes
Reference ID	String