Device dictionary

Loading…

Reference ID	String
0	Model 705 2.x
1	MAGNETROL
2	Device ID
3	Poll Address
4	Faults
5	Default Paramtrs
6	Default Parameters - Non-volatile memory contents have been overwritten with default values. Please re-enter application parameters through Calibration and Basic Setup menus.
7	No Fiducial
8	No Fiducial Pulse - Check connection between circuit boards in module.
9	No Level Signal
10	Missing Level Signal - Check probe connection and application parameters.
11	Bad Cal Paramtrs
12	Bad Calibration Paramters - Check that the correct probe length has been entered.
13	High Volume
14	High Volume Alarm - The measured level has reached 106% of the last entry in the strapping table.
15	Fault 2
16	Available for additional fault identification.
17	reserved
18	Not available for fault identification.
19	Warnings
20	Factory Cal Reqd
21	Factory Calibration required - The module requires re-calibration by the factory. The instrument will continue to operate at reduced accuracy.
22	ICF1 State Error
23	Device in unknown state when input capture interrupt occurred.
24	OCF1 State Error
25	Device in unknown state when output compare interrupt occurred.
26	ICF2 Interrupt
27	Spurious input capture interrupt occurred.
28	OCF2 Interrupt
29	Spurious output compare interrupt occurred.
30	Ovrflw Interrupt
31	Unexpected timer overflow interrupt has occurred.
32	Extern Interrupt
33	Unexpected external interrupt has occurred.
34	Sfwr Interrupt
35	Unexpected software interrupt has occurred.
36	PV is
37	Trim 4 and 20
38	Loop Test
39	Level Units
40	Select units of measurement for level output.
41	6.1f
42	Level of material in vessel
43	5.1f
44	%
45	% Output
46	Minimum Span
47	Upper Range Limit
48	Lower Range Limit
49	4.1f
50	Damping
51	5.2f
52	Loop
53	Analog output loop current
54	Alarms
55	7xA_x
56	7xA: Coaxial Probe (dielectric range >= 1.7)
57	7xB_x
58	7xB: Rigid Twin Rod Probe (dielectric range >= 2.0)
59	7xD_x
60	7xD: High Temperature-High Pressure Coaxial Probe (dielectric range >= 2.0)
61	7xP_x
62	7xP: High Pressure Coaxial Probe (dielectric range >= 1.7)
63	7xR_x
64	7xR: Coaxial Probe for flooding applications (dielectric range >= 1.7)
65	7xS_x
66	7xS: High Temperature-High Pressure Coaxial Probe for steam
67	7xU_x
68	7xU: Coaxial Probe for cryogenic liquids (dielectric range >= 1.7)
69	7x7_x
70	7x7: Flexible Twin Rod Probe (dielectric range >= 2.0)
71	7xK_x
72	7xK: Top In/Bottom Out Coaxial Probe for torque tube replacement
73	7xE_x
74	7xE: High Temperature-High Pressure Twin Rod Probe
75	Type 11
76	Type 12
77	Type 13
78	Type 14
79	Type 15
80	Type of probe connected to transmitter
81	Probe Model
82	NPT
83	US National tapered Pipe Thread
84	BSP
85	British Straight Pipe Thread
86	Flange
87	Welded ANSI or DIN Flange
88	Mount 4
89	Mount 5
90	Mounting style of probe fitting
91	Probe Mount
92	Distance from face of process seal to end of probe
93	Probe Length
94	Probe Offset
95	Desired level reading when liquid surface is at end of probe
96	1.7 - 3
97	Dielectric constant of material lies between 1.7 and 3
98	3 - 10
99	Dielectric constant of material lies between 3 and 10
100	10 - 100
101	Dielectric constant of material lies between 10 and 100
102	1.4 - 1.7
103	Dielectric constant of material lies between 1.4 and 1.7
104	Dielectric
105	Dielectric constant of material in vessel
106	8.1f
107	4mA Set Point
108	20mA Set Point
109	3.6mA
110	22mA
111	Hold
112	Fault State
113	Date/Time/Initials
114	When and by whom calibration was performed
115	3u
116	Enter Password
117	Password is required for adjusting Advanced Setup parameters Magnetrol S/N and Device id, and Factory Settings parameters Nearzone, Window, Range, Gain,Conversion Factor, Scale Offset, and Target Calibration for Steam Probes.
118	Magnetrol S/N
119	Factory parameter, displayed for diagnostic purposes only
120	8u
121	New User Password
122	User password required to change parameter settings from keypad
123	Nearzone
124	Factory parameter: distance along probe where instrument begins sensing level of material in vessel. WARNING: Operation of instrument is undefined if level rises into nearzone region.
125	4u
126	Ticks
127	Fiducial Ticks
128	<Window>
129	Range
130	Gain
131	Conversion Factor
132	4i
133	Scale Offset
134	5d
135	Derating Factor
136	Run
137	Cal
138	Oper Mode
139	Target Ticks
140	Target Ratio
141	Target Gain
142	Targ Cal Tks
143	CFD
144	Fixed
145	Threshold
146	Use 'CFD' except in situation with low dielectric (< 3) material over higher dielectric (> 10) material, e.g., oil over water, in which case use 'Fixed'.
147	# of Ticks
148	Damped time of flight. Factory parameter, displayed for diagnostic purposes only
149	4mA Trim Value
150	20mA Trim Value
151	Firmware Version
152	Main Menu
153	Device Setup
154	Basic Setup
155	Advanced Setup
156	Diagnostics
157	Factory Settings
158	Variable Units
159	Strapping Table
160	Review
161	Target Calib
162	Captures time-of-flight to target on steam probe types at room ambient.
163	Targ Cal Abort
164	No Target detected
165	Elapsed Time
166	04d
167	sec(-ive) hrs(+ive)
168	Elapsed time since most recent significant event.
169	Event status
170	ALL FAULTS CLEARED
171	POWER ON
172	HIGH VOLUME
173	DEFAULT PARAMETERS
174	DEFAULT PARAMETERS+
175	BAD CAL PARAMETERS
176	BAD CAL PARAMETERS+
177	DEFAULT PARAMETERS++
178	NO LEVEL SIGNAL
179	NO LEVEL SIGNAL+
180	NO LEVEL SIGNAL++
181	DEFAULT PARAMTERS+++
182	NO FIDUCIAL SIGNAL
183	NO FIDUCIAL SIGNAL+
184	NO FIDUCIAL SIGNAL++
185	NO FIDUCIAL SGNAL+++
186	DEFAULT PARAMTRS++++
187	Bit encoded event status stored in log.
188	Event Interval
189	05i
190	Interval associated with a particular event that is the time elapsed since the previous event.
191	No earlier event
192	No later event
193	Display Event Log
194	Displays history of significant events such as Power On, Faults, and All Faults Cleared. The time interval displayed with a particular event is the time elapsed since the previous event. The interval associated with a Power On event is always 0.
195	g
196	l
197	Volume Units
198	Select units of measurement for volume output.
199	Volume of material in vessel
200	1731.2 g
201	17312 g
202	138500 g
203	6553.5 l
204	65535 l
205	524280 l
206	Maximum Volume
207	Select maximum volume for application.
208	Strap Table Length
209	Number of valid level-volume pairs in strapping table. A level-volume pair is valid if both values are greater than the values of the preceding level-volume pair.
210	Pt01Lvl
211	Pt02Lvl
212	Pt03Lvl
213	Pt04Lvl
214	Pt05Lvl
215	Pt06Lvl
216	Pt07Lvl
217	Pt08Lvl
218	Pt09Lvl
219	Pt10Lvl
220	Pt11Lvl
221	Pt12Lvl
222	Pt13Lvl
223	Pt14Lvl
224	Pt15Lvl
225	Pt01Vol
226	Pt02Vol
227	Pt03Vol
228	Pt04Vol
229	Pt05Vol
230	Pt06Vol
231	Pt07Vol
232	Pt08Vol
233	Pt09Vol
234	Pt10Vol
235	Pt11Vol
236	Pt12Vol
237	Pt13Vol
238	Pt14Vol
239	Pt15Vol
240	Level point value too high
241	Level point value too low
242	Volume point value too high
243	Volume point value too low
244	Lvl and Vol values out of range
245	Level
246	Volume
247
248	% Out
249
250	FMU860
251	DT
252	DVC
253	FCX
254	AS800
255	340T
256	340C
257	344
258	Siemens Micro K
259	SITRANS L
260	SIPAN PH
261	SITRANS P
262	75SMT
263	UNIDELTA
264	8320
265	SX5100
266	TSV175
267	DMU
268	3780
269	BM70
270	Target Ticks =%[4i]{0}
271	Calibration ok Set Targ Air =%[4i]{0}?
272	Calibration bad TargTks unstable
273	Interval since most recent event: %[.4d]{fault_status_age} secs
274	Interval since most recent event: %[.4d]{fault_status_age} hrs
275	Event log empty
276	Event: %{0} Interval: %[.4d]{interval_secs} secs
277	Get earlier event;Get later event
278	Event: %{0} Interval: %[.4d]{1} hrs
Reference ID	String