Device dictionary

Loading…

Reference ID	String
0	Jupiter
1	MAGNETROL
2	Device ID
3	Poll Address
4	Faults
5	Default Paramtrs
6	Default Parameters - Non-volatile memory contents have been overwritten with default values. Please re-enter application parameters through Calibration and Basic Setup menus.
7	Snsr Brd Failed
8	Sensor Board Failed - Communication with the co-processor has failed. Check connection between circuit boards in module.
9	No Level Signal
10	Missing Level Signal - Check probe and float; Check that correct probe length has been entered.
11	undefined
12	Undefined fault.
13	Warnings
14	Factory Cal Reqd
15	Factory Calibration required - The module requires re-calibration by the factory. The instrument will continue to operate at reduced accuracy.
16	Undefined warning.
17	Trim 4 and 20
18	Loop Test
19	Liquid level
20
21	Loop
22
23	% Out
24	20mA Set Point
25	4mA Set Point
26	Units
27	7.2f
28	Float level
29	6.2f
30	%
31	% Output
32	Minimum Span
33	Minimum difference between 4mA and 20mA set points
34	Upper Sensor Limit
35	Lower Sensor Limit
36	5.2f
37	Damping
38	6.3f
39	Analog output loop current
40	Distance from reference point to end of probe
41	Probe Length
42	Probe Offset
43	Distance from low end of probe to 0 level reference. Negative offset indicates low end of probe is below the 0 level reference. Positive offset indicates low end of probe is above the 0 level reference.
44	3.6mA
45	22mA
46	Latch
47	Fault State
48	Date/Time/Initials
49	When and by whom calibration was performed
50	4u
51	4mA Trim Value
52	Factory parameter, displayed for diagnostic purposes only
53	20mA Trim Value
54	3u
55	Enter Password
56	Password is required for adjusting Factory Settings
57	Magnetrol S/N
58	New User Password
59	User password required to change parameter settings from keypad
60	5u
61	Conversion Factor
62	Deadband
63	Distance from transducer to first detectable level
64	Threshold
65	Negative
66	Positive
67	Polarity
68	Sensitivity
69	Drive Amplitude
70	MLI Top
71	MLI Bottom
72	Direct Near
73	Direct Extended
74	Type 5
75	Type 6
76	Sensor Mount
77	Mounting configuration of sensor - specifies the sensor offset and reference used to determine level.
78	counts
79	# of Counts
80	Damped time of flight. Factory parameter, displayed for diagnostic purposes only
81	Firmware Version
82	Main Menu
83	Device Setup
84	Fast Calibration
85	Basic Setup
86	Advanced Setup
87	Diagnostics
88	Factory Settings
89	Review
90	Capture 4mA Level
91	Sets 4mA point to 0 and adjusts offset to give level reading of zero at float position
92	Capture 20mA Level
93	Sets 20mA point to level at float position
94	No level signal
95
96	FMU860
97	DT
98	DVC
99	FCX
100	AS800
101	340T
102	340C
103	344
104	Siemens Micro K
105	SITRANS L
106	SIPAN PH
107	SITRANS P
108	75SMT
109	UNIDELTA
110	8320
111	SX5100
112	TSV175
113	DMU
114	3780
115	BM70
116	8u
117	Move float to level desired for 4mA loop current output
118	Level = %{0} in
119	Read Level again;Set Lvl & 4mA = 0
120	Level = %{0} cm
121	Unknown selection, aborting procedure
122	No Lvl Signal aborting procedure
123	Warning: set points closer than minimum span
124	Unknown response code aborting procedure
125	Move float to level desired for 20mA loop current output
126	Read Level again;Set 20mA = Level
Reference ID	String