| 0 |
Message |
| 1 |
No error |
| 2 |
INVALID PARAMETER |
| 3 |
INVALID SPAN OUT2 |
| 4 |
INVALID SPAN OUT1 |
| 5 |
OUTPUT 2 TOO HIGH |
| 6 |
OUTPUT 2 TOO LOW |
| 7 |
OUTPUT 1 TOO HIGH |
| 8 |
OUTPUT 1 TOO LOW |
| 9 |
OUTPUT LOAD |
| 10 |
NO FAILURE |
| 11 |
016 SENSOCHECK REF-EL |
| 12 |
015 SENSOCHECK GLAS-EL |
| 13 |
010 RANGE ORP |
| 14 |
011 RANGE PH |
| 15 |
013 RANGE TEMPERATURE |
| 16 |
012 RANGE MV |
| 17 |
005 CAL DATA |
| 18 |
004 SENSOR FAILURE |
| 19 |
003 CANCELED SENSOR |
| 20 |
002 WRONG SENSOR |
| 21 |
001 NO SENSOR |
| 22 |
WRONG MODULE |
| 23 |
NO MODULE INSTALLED |
| 24 |
SYSTEM ERROR |
| 25 |
CONFIGURATION ERROR |
| 26 |
DEVICE FAILURE |
| 27 |
SIP CYCLE |
| 28 |
CIP CYCLE |
| 29 |
CALIBRATION |
| 30 |
SERVICE |
| 31 |
PARSET A |
| 32 |
PARSET B |
| 33 |
CONFIGURATION |
| 34 |
DOOR OPEN |
| 35 |
POWER |
| 36 |
TEMP. OUTSIDE TABLE |
| 37 |
MEMOSENS S-No |
| 38 |
ISM SENSOR S-No |
| 39 |
INDUCON S-No |
| 40 |
..PH [PH] |
| 41 |
..TMAX [°C] |
| 42 |
..SLOPE [%] |
| 43 |
..ZERO [mV] |
| 44 |
SIP-CYCLES OVERRUN |
| 45 |
CIP-CYCLES OVERRUN |
| 46 |
SENSOR WEAR |
| 47 |
SENSOR DRIFT |
| 48 |
SENSOR ZERO/SLOPE |
| 49 |
OUT OF CAL TIME |
| 50 |
FAILURE BUFFERSET -U1- |
| 51 |
INVALID PARAMETER CONTROLLER |
| 52 |
INVALID SPAN I-INPUT |
| 53 |
ISFET-ZERO CAL OR CHANGE |
| 54 |
FLOW TOO LOW |
| 55 |
FLOW TOO HIGH |
| 56 |
INVAL CH SEL RELAYS |
| 57 |
not used |
| 58 |
Date |
| 59 |
Date when the event occurred |
| 60 |
Time |
| 61 |
Time of day when the event occurred |
| 62 |
Type |
| 63 |
Message type |
| 64 |
static message |
| 65 |
Begin of event |
| 66 |
End of event |
| 67 |
static message |
| 68 |
static message |
| 69 |
message_dummy |
| 70 |
Parset |
| 71 |
Parameter set A |
| 72 |
Parameter set B |
| 73 |
Sensoface |
| 74 |
Sensoface message |
| 75 |
good |
| 76 |
medium |
| 77 |
bad |
| 78 |
unknown |
| 79 |
Value |
| 80 |
Error value |
| 81 |
First selected entry |
| 82 |
Second selected entry |
| 83 |
Entries |
| 84 |
0..1 |
| 85 |
2..3 |
| 86 |
4..5 |
| 87 |
6..7 |
| 88 |
8..9 |
| 89 |
10..11 |
| 90 |
12..13 |
| 91 |
14..15 |
| 92 |
16..17 |
| 93 |
18..19 |
| 94 |
20..21 |
| 95 |
22..23 |
| 96 |
24..25 |
| 97 |
26..27 |
| 98 |
28..29 |
| 99 |
30..31 |
| 100 |
32..33 |
| 101 |
34..35 |
| 102 |
36..37 |
| 103 |
38..39 |
| 104 |
40..41 |
| 105 |
42..43 |
| 106 |
44..45 |
| 107 |
46..47 |
| 108 |
48..49 |
| 109 |
50..51 |
| 110 |
52..53 |
| 111 |
54..55 |
| 112 |
56..57 |
| 113 |
58..59 |
| 114 |
60..61 |
| 115 |
62..63 |
| 116 |
64..65 |
| 117 |
66..67 |
| 118 |
68..69 |
| 119 |
70..71 |
| 120 |
72..73 |
| 121 |
74..75 |
| 122 |
76..77 |
| 123 |
78..79 |
| 124 |
80..81 |
| 125 |
82..83 |
| 126 |
84..85 |
| 127 |
86..87 |
| 128 |
88..89 |
| 129 |
90..91 |
| 130 |
92..93 |
| 131 |
94..95 |
| 132 |
96..97 |
| 133 |
98..99 |
| 134 |
100..101 |
| 135 |
102..103 |
| 136 |
104..105 |
| 137 |
106..107 |
| 138 |
108..109 |
| 139 |
110..111 |
| 140 |
112..113 |
| 141 |
114..115 |
| 142 |
116..117 |
| 143 |
118..119 |
| 144 |
120..121 |
| 145 |
122..123 |
| 146 |
124..125 |
| 147 |
126..127 |
| 148 |
128..129 |
| 149 |
130..131 |
| 150 |
132..133 |
| 151 |
134..135 |
| 152 |
136..137 |
| 153 |
138..139 |
| 154 |
140..141 |
| 155 |
142..143 |
| 156 |
144..145 |
| 157 |
146..147 |
| 158 |
148..149 |
| 159 |
150..151 |
| 160 |
152..153 |
| 161 |
154..155 |
| 162 |
156..157 |
| 163 |
158..159 |
| 164 |
160..161 |
| 165 |
162..163 |
| 166 |
164..165 |
| 167 |
166..167 |
| 168 |
168..169 |
| 169 |
170..171 |
| 170 |
172..173 |
| 171 |
174..175 |
| 172 |
176..177 |
| 173 |
178..179 |
| 174 |
180..181 |
| 175 |
182..183 |
| 176 |
184..185 |
| 177 |
186..187 |
| 178 |
188..189 |
| 179 |
190..191 |
| 180 |
192..193 |
| 181 |
194..195 |
| 182 |
196..197 |
| 183 |
198..199 |
| 184 |
INDEX_FROM_FIRST |
| 185 |
NewestEntry |
| 186 |
device busy |
| 187 |
Device |
| 188 |
Process Variables |
| 189 |
Diagnostic |
| 190 |
Offline |
| 191 |
Primary |
| 192 |
Secondary |
| 193 |
Service |
| 194 |
Blink |
| 195 |
Generate a flash light signal with the display backlight. |
| 196 |
Signal |
| 197 |
Configuration flag reset |
| 198 |
Command resets the configuration flag. |
| 199 |
Lock/Unlock device |
| 200 |
Device information |
| 201 |
Device description |
| 202 |
4 wire analysis device for pH-measurement |
| 203 |
Device options |
| 204 |
Sensor information |
| 205 |
No sensor information available |
| 206 |
HART |
| 207 |
Measuring point |
| 208 |
Versions |
| 209 |
HART interface |
| 210 |
Measuring channel |
| 211 |
Calibration values |
| 212 |
ISFET Offset |
| 213 |
Last calibration |
| 214 |
Next calibration |
| 215 |
Sensor monitor |
| 216 |
Imp. glass electrode |
| 217 |
Imp. refer. electrode |
| 218 |
Resist. temp. sensor |
| 219 |
Input current |
| 220 |
Sensor wear |
| 221 |
Sensor operation time |
| 222 |
Lifetime |
| 223 |
CIP counter |
| 224 |
SIP counter |
| 225 |
Autoclave counter |
| 226 |
Configuration |
| 227 |
SENSOR |
| 228 |
RTD TYPE |
| 229 |
TEMP MEAS VALUE |
| 230 |
TEMP CAL VALUE |
| 231 |
BUFFER SET |
| 232 |
BUFFER SET-VALUES |
| 233 |
Buffer 1 |
| 234 |
Buffer 2 |
| 235 |
Write Buffer Set |
| 236 |
CAL CYCLE |
| 237 |
CIP COUNT |
| 238 |
CIP CYCLES |
| 239 |
SIP COUNT |
| 240 |
SIP CYCLES |
| 241 |
OUT 1 |
| 242 |
HOLD FIX VALUE |
| 243 |
OUT 2 |
| 244 |
CORRECTION |
| 245 |
TC LIQUID |
| 246 |
ALARM |
| 247 |
REL1/REL2 |
| 248 |
MIN A |
| 249 |
MIN B |
| 250 |
MAX A |
| 251 |
MAX B |
| 252 |
CONTROLLER |
| 253 |
PULSE FREQ |
| 254 |
PULSE LEN |
| 255 |
WASH |
| 256 |
WASH CONFIGURATION |
| 257 |
PARSET |
| 258 |
CLOCK |
| 259 |
Clock |
| 260 |
Product calibration |
| 261 |
Save currently measured value |
| 262 |
Zero and Slope |
| 263 |
Parameter set |
| 264 |
Change parameter set |
| 265 |
Measurement value |
| 266 |
Output current |
| 267 |
|
| 268 |
Logbook |
| 269 |
Explosion protection |
| 270 |
none Ex device |
| 271 |
Ex device |
| 272 |
Number of current output |
| 273 |
one current output |
| 274 |
two current outputs |
| 275 |
SIL State |
| 276 |
no SIL |
| 277 |
SIL |
| 278 |
not activated |
| 279 |
activated |
| 280 |
I-Input |
| 281 |
ISM |
| 282 |
Audit trail |
| 283 |
100PT |
| 284 |
1000PT |
| 285 |
30NTC |
| 286 |
TEMP UNIT |
| 287 |
CALMODE |
| 288 |
AUTO |
| 289 |
MAN |
| 290 |
DAT |
| 291 |
CALTIMER |
| 292 |
OFF |
| 293 |
FIX |
| 294 |
ADAPT |
| 295 |
ON |
| 296 |
Sensor type |
| 297 |
Manufacturer |
| 298 |
Sensor description |
| 299 |
Serial number |
| 300 |
Date of last calibration |
| 301 |
Connection state |
| 302 |
disconnected |
| 303 |
connected |
| 304 |
Measured value |
| 305 |
.2f |
| 306 |
Reference value |
| 307 |
Calibration Mode |
| 308 |
Saturation |
| 309 |
Calibration result |
| 310 |
Slope unit |
| 311 |
Slope |
| 312 |
Zero unit |
| 313 |
Zero |
| 314 |
.0f |
| 315 |
index of sensor info array |
| 316 |
Software version |
| 317 |
Hardware version |
| 318 |
Channel1 Software version |
| 319 |
Channel1 Hardware version |
| 320 |
Channel1 Serial number |
| 321 |
Change ParaSet |
| 322 |
Parameter Set A |
| 323 |
Parameter Set B |
| 324 |
dyn_var_assign_index_code |
| 325 |
Active parset |
| 326 |
UNIT |
| 327 |
RANGE |
| 328 |
0-20 mA |
| 329 |
4-20 mA |
| 330 |
FILTERTIME |
| 331 |
22mA-FAIL |
| 332 |
HOLD MODE |
| 333 |
LAST |
| 334 |
method_update_DISPLAY_UNIT |
| 335 |
Unit |
| 336 |
DELAYTIME |
| 337 |
SENSOCHECK |
| 338 |
FUNCTION |
| 339 |
FUNCTION MIN/MAX |
| 340 |
LIMITS |
| 341 |
CHANNEL |
| 342 |
RL1: CHANNEL |
| 343 |
PH |
| 344 |
ORP |
| 345 |
TMP |
| 346 |
RL1: FUNCTION |
| 347 |
Low Level |
| 348 |
High Level |
| 349 |
CONTACT |
| 350 |
RL1: CONTACT |
| 351 |
N/O |
| 352 |
N/C |
| 353 |
LEVEL |
| 354 |
RL1: LEVEL |
| 355 |
HYSTERESIS |
| 356 |
RL1: HYSTERESIS |
| 357 |
RL1: DELAYTIME |
| 358 |
RL2: CHANNEL |
| 359 |
RL2: FUNCTION |
| 360 |
RL2: CONTACT |
| 361 |
RL2: LEVEL |
| 362 |
RL2: HYSTERESIS |
| 363 |
RL2: DELAYTIME |
| 364 |
CTR: CHANNEL |
| 365 |
TYPE |
| 366 |
CTR: TYPE |
| 367 |
PLC |
| 368 |
PFC |
| 369 |
CTR: PULSE LEN |
| 370 |
CTR: PULSE FREQ |
| 371 |
min-1 |
| 372 |
SETPOINT |
| 373 |
CTR: SETPOINT |
| 374 |
DEAD BAND |
| 375 |
CTR: DEAD BAND |
| 376 |
P-GAIN |
| 377 |
CTR: P-GAIN |
| 378 |
I-TIME |
| 379 |
CTR: I-TIME |
| 380 |
D-TIME |
| 381 |
CTR: D-TIME |
| 382 |
CTR: HOLD MODE |
| 383 |
Y Off |
| 384 |
Y LAST |
| 385 |
FUNCTION WASH |
| 386 |
PARSET A/B |
| 387 |
WASH CYCLE |
| 388 |
WASH TIME |
| 389 |
PARSET CHANGE |
| 390 |
CNTR INPUT |
| 391 |
MANUAL |
| 392 |
PAR A FIX |
| 393 |
ms |
| 394 |
min |
| 395 |
hour |
| 396 |
date |
| 397 |
summer normal |
| 398 |
standard time |
| 399 |
summer time |
| 400 |
Device tag |
| 401 |
str_Sensor_Selection_Calib |
| 402 |
Unit Zero |
| 403 |
.1f |
| 404 |
Unit Slope |
| 405 |
Next calibration in |
| 406 |
Unit Time next Calibration |
| 407 |
Unit Resist. temp. sensor |
| 408 |
Temperature |
| 409 |
Unit Temperature |
| 410 |
Unit Input current |
| 411 |
Unit Sensor operation time |
| 412 |
Unit lifetime |
| 413 |
CIP counter (Cleaning In Place) |
| 414 |
Cyc |
| 415 |
Unit CIP counter |
| 416 |
SIP counter (Sterilisation In Place) |
| 417 |
Unit SIP counter |
| 418 |
Unit autoclave cycles |
| 419 |
index of DSM info value array |
| 420 |
Last calibration date |
| 421 |
Loop current 1 |
| 422 |
Loop current Unit |
| 423 |
Loop current 2 |
| 424 |
Alarm type |
| 425 |
8.2f |
| 426 |
.3f |
| 427 |
8.3f |
| 428 |
SV % rnge |
| 429 |
pH Value |
| 430 |
USL |
| 431 |
LSL |
| 432 |
3.f |
| 433 |
7d |
| 434 |
Temperature Compensation |
| 435 |
Number of signal |
| 436 |
1 |
| 437 |
2 |
| 438 |
3 |
| 439 |
4 |
| 440 |
5 |
| 441 |
Primary value |
| 442 |
Secondary value |
| 443 |
Chart measurement value |
| 444 |
Primary current output |
| 445 |
Secondary current output |
| 446 |
Current outputs |
| 447 |
Hold mode |
| 448 |
Picture active parset |
| 449 |
STANDARD |
| 450 |
ISFET |
| 451 |
INDUCON |
| 452 |
ISM |
| 453 |
MEMOSENS |
| 454 |
TEMP MEAS |
| 455 |
EXT |
| 456 |
TEMP CAL |
| 457 |
TEMP CAL_VALUE |
| 458 |
-00- Knick |
| 459 |
-01- Mettler-Toledo |
| 460 |
-02- Merck/Riedel de Haen |
| 461 |
-03- Ciba (94) |
| 462 |
-04- NIST Technisch |
| 463 |
-05- NIST Standard |
| 464 |
-06- HACH |
| 465 |
-07- WTW techn. Puffer |
| 466 |
-08- Hamilton |
| 467 |
-09- Reagecon |
| 468 |
-U1- user specific |
| 469 |
BEGIN |
| 470 |
END |
| 471 |
%/K |
| 472 |
I-INPUT |
| 473 |
ORP Value |
| 474 |
Unit ISFET Offset |
| 475 |
index of calib. value array |
| 476 |
Unit imp. glass electrode |
| 477 |
Unit imp. refer. electrode |
| 478 |
pH value |
| 479 |
Unit pH value |
| 480 |
ORP value |
| 481 |
Unit ORP value |
| 482 |
pH-El. voltage |
| 483 |
Unit pH-El. voltage |
| 484 |
Glass Millivolt (ORP) |
| 485 |
Unit lass Millivolt (ORP) |
| 486 |
Unit Glass Millivolt (ORP) |
| 487 |
index of proc. value array |
| 488 |
Unit sensor wear |
| 489 |
at 0 degC |
| 490 |
at 5 degC |
| 491 |
at 10 degC |
| 492 |
at 15 degC |
| 493 |
at 20 degC |
| 494 |
at 25 degC |
| 495 |
at 30 degC |
| 496 |
at 35 degC |
| 497 |
at 40 degC |
| 498 |
at 45 degC |
| 499 |
at 50 degC |
| 500 |
at 55 degC |
| 501 |
at 60 degC |
| 502 |
at 65 degC |
| 503 |
at 70 degC |
| 504 |
at 75 degC |
| 505 |
at 80 degC |
| 506 |
at 85 degC |
| 507 |
at 90 degC |
| 508 |
at 95 degC |
| 509 |
index of buffer value array |
| 510 |
Consistent check |
| 511 |
data consistent |
| 512 |
data inconsistent |
| 513 |
Loop current saturated |
| 514 |
Out 1 Saturated |
| 515 |
Out 2 Saturated |
| 516 |
Analog output fixed |
| 517 |
Field Device Specific Dynamic Variable Analog Output Fixed. Data indicating which of the Analog Outputs are, or are not, Fixed. The analog and digital Analog Outputs for the Dynamic Variable are held at a constant value (depending on the Mode of the Field Device). They will not respond to the applied process. |
| 518 |
Out 1 fixed |
| 519 |
Out 2 fixed |
| 520 |
Stratos Pro pH (4-wire) |
| 521 |
dummy |
| 522 |
|
| 523 |
Error number |
| 524 |
Local device mode |
| 525 |
Measure |
| 526 |
Diagnosis |
| 527 |
Calibration |
| 528 |
Service |
| 529 |
sensoface |
| 530 |
Hold |
| 531 |
Hold state |
| 532 |
Inactive |
| 533 |
Active |
| 534 |
Product calibration state sensor |
| 535 |
Product calibration sensor 2 |
| 536 |
Product calibration state sensor 2 |
| 537 |
Sensor connection |
| 538 |
disconnected |
| 539 |
connected |
| 540 |
Alarm |
| 541 |
Temperature Value |
| 542 |
Upload Variables |
| 543 |
PV Analog Channel Saturated |
| 544 |
PV Analog Channel Fixed |
| 545 |
Wireless |
| 546 |
WirelessHART Device |
| 547 |
IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation |
| 548 |
Critical Power Failure |
| 549 |
Lock all |
| 550 |
Configuration cannot be changed |
| 551 |
Locked by gateway |
| 552 |
Analog Input Channel |
| 553 |
Analog Output Channel |
| 554 |
Secondary Analog Channel Saturated |
| 555 |
Tertiary Analog Channel Saturated |
| 556 |
Quaternary Analog Channel Saturated |
| 557 |
Quinary Analog Channel Saturated |
| 558 |
Secondary Analog Channel Fixed |
| 559 |
Tertiary Analog Channel Fixed |
| 560 |
Quaternary Analog Channel Fixed |
| 561 |
Quinary Analog Channel Fixed |
| 562 |
8u |
| 563 |
Device Variable |
| 564 |
Analog Channel Number |
| 565 |
Analog Channel Number- Index into an array of Analog Channels. |
| 566 |
Display is flashing ... |
| 567 |
Execute configuration flag reset? |
| 568 |
Do you really want to write buffer set? |
| 569 |
Yes;Abort |
| 570 |
Result buffer check: %{0} |
| 571 |
Please wait! |
| 572 |
Please select the desired Parset |
| 573 |
Parset A;Parset B;Abort |
| 574 |
Change of parameter set not permitted, because parameter set A is fixed.
To permit parameter set changes please adjust the configuration! |