Device dictionary

Loading…

Reference ID	String
0	2211Cond
1	KNICK
2	Polling address
3	Message
4	Device tag
5	Descriptor
6	Date
7	Assembly num
8	Error status
9	Field Device Error Status- Failure messages of the Field Device are listed
10	01 Conductivity
11	02 Conductance
12	03 Temp. value
13	21 Loop < 3.8mA
14	22 Loop >20.5mA
15	23 Loop span
16	98 Config data
17	99 Data lost
18	Smiley sad
19	Status of sad Smiley- Correct measurment is no longer ensured. Sensoface provides information on wear and required maintance. However the unit can still determine the measured variable and output it via the loop current.
20	Polarisation
21	Lead
22	Cellconstant
23	Analog out satrd
24	HOLD mode
25	Analog Outputs of the Field Device are fixed in HOLD mode. The analog and digital Analog Outputs for the Dynamic Variable are held at a constant value. They will not respond to the applied process.
26	Resp.preambles
27	Online
28	ProcessVariables
29	Diag/Service
30	Device Data
31	Configuration
32	Review
33	Diagnosis
34	Temperature Setup
35	Output Setup
36	Cal. Setup
37	Alarm Setup
38	Sensors
39	Outputs
40	Device information
41	Meas/Out Relation
42	mA Output ranges
43	Dummy1Byte
44	sel. code index
45
46	selection codes
47	Input Selection Code
48	TC Selection Code
49	Output Function Code
50	Diag. Code
51	Output Selection Code
52	Invalid unit code
53	Busy
54	Unit
55	%/K
56	g/kg
57	µS
58	mS
59	MOhm
60	SAL
61	5.3f
62	5.2f
63	5.1f
64	4.0f
65	USL
66	6.0f
67	7.3f
68	LSL
69	span
70	Ohm
71	6.3f
72	Number
73	You can choose the kind of dependence of the currentfrom the digital value
74	Inp.units
75	Temp
76	Temperature, displayed, used to compute the salinity or used to compute the temperature compensated conductivity
77	°C
78	°F
79	3.0f
80	Cond.
81	Conductivity, temperature compensated if applied
82	Res.
83	Specific resistance, temperature compensated if applied
84	Salinity
85	Salinity calculated from conductivity and temperature
86	4.1f
87	PV AO
88	PV % rnge
89	%
90	Edit lin. TC
91	linear temperature coefficent used to compute the temperature compensated conductivity if applied
92	HOLD fix value
93	Specify fixed output current in HOLD mode
94	PV unit
95	0.000 µS
96	00.00 µS
97	000.0 µS
98	0000 µS
99	0.000 mS
100	00.00 mS
101	000.0 mS
102	0.000 MOhm
103	00.00 MOhm
104	000.0 MOhm
105	000.0 SAL
106	Cell Type
107	2-EL
108	4-EL
109	Temp. unit
110	Sensor
111	Pt100
112	Pt1000
113	NTC100k
114	NTC30k
115	TC function
116	OFF
117	LIN
118	NLF
119	-01- FCT (NaCl)
120	-02- FCT (HCl)
121	-03- FCT (NH3)
122	Output lin./log.
123	lin
124	log
125	log: lower range
126	0.1 mS
127	1.000 mS
128	10.00 mS
129	100.0 mS
130	1000 mS
131	log: upper range
132	Sensocheck
133	Sensocheck continously monitors the sensor.
134	Off
135	On
136	Cellconstant according to data sheet or calibration
137	1/cm
138	6.4f
139	22mA on Error
140	Switch 22mA signal for error message on or off
141	HOLD Last/Fix
142	The output current behavior in the HOLD mode can be specified. Last- The output current is frozen at its last value, Fix- A constant value from 3.8mA to 22mA
143	Last value
144	Fixed current
145	Loop test
146	Meas. Range&Unit
147	Select Cell
148	Select 2-electrode cell or 4-electrode cell
149	Temperature Unit
150	Select the temperature unit for HART and local display.
151	Sensor type
152	Select the temperature sensor type
153	Select TC function
154	The displayed conductivity value is calculated from measured data and TC
155	mA lin./log.
156	Select linear or logarithmic meas. value / output current relation
157	edit log. lrv
158	Select log lower range value
159	edit log. urv
160	Select log upper range value
161	Sensocheck continuously monitors the sensor.
162	22mA on error
163	Self test
164	Performs transmitter self test
165	Master reset
166	Performs master reset in the Field Device
167	FMU860
168	DT
169	DVC
170	FCX
171	AS800
172	340T
173	340C
174	344
175	Siemens Micro K
176	SITRANS L
177	SIPAN PH
178	SITRANS P
179	75SMT
180	UNIDELTA
181	8320
182	SX5100
183	TSV175
184	DMU
185	3780
186	BM70
187	8u
188	- %{0} -
189	Meas. Range & Unit
190	0.000 µS;00.00 µS;000.0 µS;0000 µS;0.000 mS;00.00 mS;000.0 mS;0.000 MOhm;00.00 MOhm;000.0 MOhm;000.0 SAL
191	Cell Type
192	2-EL;4-EL
193	Temp unit
194	°C;°F
195	Pt100;Pt1000;NTC100k;NTC30k
196	TC function
197	OFF;LIN;NLF;-01- FCT (NaCl);-02- FCT (HCl);-03- FCT (NH3)
198	lin.;log.
199	log lower range value
200	0.1 µS/mS/MOhm;1.000 µS/mS/MOhm;10.00 µS/mS/MOhm;100.0 µS/mS/MOhm;1000 µS/mS/MOhm
201	log upper range value
202	Off;On
203	Last value;Fixed current
204	Press OK to perform transmitter self test
205	Press OK to perform master reset
Reference ID	String