Device dictionary

Loading…

Reference ID	String
0	ISE-MAGTECH
1	LTM-300
2	Operation Status
3	Lev sig lost
4	Level signal is lost. Check float.
5	Float Maint Needed
6	Level signal inconsistent. Check float and threshold adjustment. Retrim level.
7	Intf sig lost
8	Interf signal is lost. Check floats.
9	Temper snsr open
10	Temperature sensor is open. Check sensor.
11	Temper snsr shrt
12	Temperature sensor is shorted. Check sensor.
13	Power Supply low
14	Power supply voltage low. Check loop Power Supply.
15	Cal Status
16	Lev Gain not cal
17	Level Gain out of range. Retrim level.
18	Lev Zero not cal
19	Level Zero point out of range. Retrim level.
20	Dac Gain not cal
21	DAC Gain not calibrated. Recalibrate DAC.
22	Dac Zero not cal
23	DAC Zero not calibrated. Recalibrate DAC.
24	Tmp Gain not cal
25	Temper Gain out of range. Retrim temperature.
26	Tmp Zero not cal
27	Temper Zero out of range. Retrim temperature.
28	Zero Level Trim
29	Level
30	Interf
31	Temper
32	Damping
33	Damping Value- Damping time constant applied to both
34	Level Trim Pt
35	Upper Trim Value- Pressure Input Used for upper trim
36	% range
37	Temper Trim Pt
38	Set the input temperature to a value near the highest process temperature expected.
39	Config.
40	Defines the variables being measured.
41	Level+Interf
42	Level+Temper
43	Level+Interf+Temper
44	Probe Lngth
45	The measurement length of the probe.
46	.3f
47	.2f
48	.1f
49	Unit
50	7d
51	8.3f
52	2.0f
53	sec
54	Temper Units
55	3.0f
56	5.2f
57	%
58	View status
59	Reports any currently active device status information.
60	Select PV
61	TBD
62	Full Level Trim
63	This method allows both zero and full scale trim
64	Zero Temper Trim
65	Full Temper Trim
66	Reset Maintenance
67	Allows the user to reset the maintenance flag.
68	Keypad rerange
69	Diagnostics
70	Calibration
71	Rerange
72	Sensor Trim
73	Upload variables
74	FMU860
75	DT
76	DVC
77	FCX
78	AS800
79	340T
80	340C
81	344
82	Siemens Micro K
83	SITRANS L
84	SIPAN PH
85	SITRANS P
86	75SMT
87	UNIDELTA
88	8320
89	SX5100
90	TSV175
91	DMU
92	3780
93	BM70
94	8u
95	low
96	high
97	tmp_av
98	Transmitter status complete
99	Transmitter status OK
100	PV is %{0}
101	Level;Interf
102	Set the level to the desired zero trim point
103	Reset the zero level trim point to continue?
104	Set the level to the desired high trim point
105	Input the level value at the high trim point.
106	Reset the high level trim point to continue?
107	Sensor upper trim succeeded
108	Set the temperature to 0 deg C/32 deg F (RTD value of 1000 ohms).
109	Reset the zero temper trim point to continue?
110	Set the temperature to the desired high trim point
111	Input the temperature value at the high trim point.
112	Reset the high temperature trim point to continue?
113	This will reset maintenance flags
114	No;Yes
115	Maintenance flags reset
Reference ID	String