HART设备字典

Loading…

引用ID	字符串
0	SVi1000
1	special
2	smart filter
3	Field Device Software Revision- This revision corresponds tothe software or firmware, that is embedded in the Field Device.
4	Response Code
5	Fault Code 0
6	Reports Device Errors
7	Reset
8	Device reset indicator
9	Low Power
10	Input current less than 3.2 mA
11	Actuator Error
12	Unable to position the valve normally.
13	Low Air Supply Warning
14	Supply Pressure below low limit
15	Position Error
16	If T1 error is configured AND the position error outside the error band for time T1
17	Internal Error
18	A critical internal fault
19	Keypad Fault
20	Possible moisture inside or connector or mechanical failure
21	Marginal Power
22
23	Fault Code 1
24	Calibration Failed
25	Calibration of AO or pressure failed
26	Find Stops Failed
27	Find Stops process failed
28	Autotune Failed
29	Self-tuning failed to converge on acceptable parameters
30	Operating System Fault
31	An internal error from which the device recovered automatically
32	Supply Pressure above upper limit
33	Fault Code 2
34	Bias Out Of Range
35	An important internal parameter is out of range
36	I/P Out Of Range
37	I/P current feedback is out of range
38	Tempertaure outside operating range
39	Low supply pressure alarm limit is configured too low
40	Auxiliary memory fault
41	Fault Code 3
42	NVM Checksum Error
43	The device failed to read critical data from non-volatile memory
44	RAM Checksum Error
45	Flash Checksum Error
46	Stack Error
47	Factory Write Indicator
48	Indicator of writes to non-volatile memory allowed only for firmware upgrade
49	NVM Test Error
50	An error in non-volatile memory could not be repaired
51	ESD Trip occurred and requires user intervention to be released
52	Factory Mode Indicator
53	Device performs factory-authorized operations
54	Fault Code 4
55	Ref Voltage Fault
56	May indicate faulty A/D subsystem
57	Position Sensor Fault
58	Current Sensor Fault
59	Temperature Sensor Fault
60	Output Pressure Sensor Fault (Single acting) or Output 2 Pressure Sensor Fault (double acting)
61	Supply Pressure Sensor Fault (Single acting) or Output 1 Pressure Sensor Fault (double acting)
62	Supply Pressure Sensor Fault (double acting only)
63	Fault Code 5
64	I/P Pressure Sensor Fault
65	Atmospheric Pressure Sensor Fault
66	NVM Write Fault
67	A write to non-volatile memory failed; data may be lost on reset
68	IRQ Fault
69	The test didn't complete in time
70	MCU Internal Malfunction
71	Software Error
72	Quick Access Key
73	Maintenance
74	Offline
75	Online (SVi1000)
76	Device Setup
77	Process Variables
78	Status/Diagnostics
79	Calibration
80	Commissioning Services
81	Basic Info.
82	Valve Travel
83	Manual Position Setpoint
84	Manual Setup
85	Sensors
86	Status/Faults
87	Fault List
88	display current and historic faults
89	Sensor Measurements
90	Continuous Diagnostics Data
91	I/P
92	Temperature
93	Raw Sensor Data
94	Select the slot
95	To load the tuning parameters stored in the specific slot
96	Display PID in Slot
97	Display the PID's parameters in the other slot.
98	Valve Tuning Data
99	Alarms Setup
100	Switches
101	General
102	Device Info
103	Hart Info
104	Information for HART
105	Configuration
106	Positioning
107	Limits/Shutoff
108	HART
109	Position Retransmit
110	Position
111	Pressure
112	Supply Pressure
113	Pressure 2
114	Valve Position
115	Valve Position- Indicates the actual valve position in % with closed = 0 % and opened = 100 %
116	%
117	.1f
118	Pressure- Indicates the actual valve pressure in its engineering unit.
119	.2f
120	.3f
121	Input Signal
122	Input Percent Range- Input signal (current loop) in percent
123	7d
124	Pressure Unit from command 3
125	Pressure Unit for SV The actual pressure reported by the SVi1000 can be inpsi, bar or kPa(for sv)
126	N/A
127	Not_Used
128	Supply Pressure Unit from command 3
129	Pressure Unit for TV The Supply pressure reported by the SVi1000 can bein psi, bar or kPa(for TV)
130	P2 Pressure Unit for double actuator from command 3
131	P2 Pressure Unit for QV The actual pressure reported by the SVi1000 can bein psi, bar or kPa(for QV)
132	Unused
133	1
134	2
135	3
136	fill
137	Firmware Version
138	Display the firmware version.
139	Change Mode
140	Change mode: Changes the mode to Normal Mode, Manual Mode, or Setup Mode. Normal Mode: The position setpoint follows the input signal. Always return to Normal Mode to return to Control by the Control System. Manual Mode: The position setpoint remains at the last position prior to entering Manual Mode. Position setpoint may adjusted with the local pushbuttons or by HART commands. Setup Mode: The position setpoint remains at the last position prior to entering Setup Mode. Use this mode to change configuration and calibration information.
141	Find Stops
142	Run automatic find stops will establish the calibration position of the valve at actuator pressure vented and at full supply pressure.
143	Autotune
144	Run PID Autotune will automatically find best dynamic parameters for responsive valve positioning. Always isolate the valve from the process. The valve will move full open and full closed. The valve will continuously change position for about 5 minutes. To SVi1000 device, this operation need the device should be set PID selector to slot 0/ATO or slot 8/ATC
145	Setup Wizard
146	The setup wizard will guide you through basic steps to setup the positioner on an actuator. You may skip this wizard if the valve and positioner have been factory configured and calibrated. Always isolate the valve from the process. The wizard allows setting Air Action. The valve move full open and full closed. You will be prompted if mode must be changed. The steps are in the following order: 1. Run Find Stops, to set 0% to the valve closed position and to set 100% to full opened position. 2. Run Auto Tune to determine best dynamic parameters for position control. 3. Reset Basic Configuration and Calibration to Factory Defaults.
147	Reset Basic Config and Cal To Defaults
148	The Reset to Factory Default will set the following list of configuration and calibration parameters to defaults: The PID tunning parameters in slot 0 are set to defaults; Input current range is set to 4 to 20 mA; Open stop adjustment is set to 100%; Position error parameters are reset and disabled; Bumpless transfer is disabled; Position limits are disabled; Position rate limits are disabled; Tight shutoff is set to 0 and enabled; Characterization is set to linear;
149	Current Faults
150	Read the current faults of device.
151	Read/Clear Faults
152	Read the device's current faults. Optionally, the fault status may also be cleared.
153	Clear Current Faults
154	Clear the current device status/faults
155	Historical Faults
156	Read the historical faults of device.
157	Clear All Faults
158	Clear the historic and current device faults/status.
159	Set Position
160	Set manual valve setpoint in % or set the position by equivalent input current to simulate non-linear characterization and limits.
161	Full Open
162	Fully Open valve
163	Full Closed
164	Fully Close Valve
165	Configure Wizard
166	Change configuration of Tight shutoff.
167	Custom / Standard Characterization
168	Control valves are often characterized to give a specific relationship between flow capacity (Cv) and percent opening of the valve. The valve can be characterized with special purpose trim or with the SVi1000 positioner. Selecting Custom Configuration displays an additional screen where the user can enter a custom characterization curve to fit his/her needs. The curve can have up to 9 points and points in between are linearly interpolated.
169	Manual Stops
170	This method is used to set manual stops.
171	Open Stop Adjustment
172	Open stop adjustment; Allows to adjust travel to less than mechanical limits. Must be between 60% and 100% of mechanical travel set with Find Stops.
173	Manual Tuning
174	The user can set tuning PID parameters for slot 0, even though the current selector was selected for the other slot. To SVi1000 device, The only slot 0 PID parameters can be updated.
175	abort restore
176	Set I/P Output
177	Set IP Value. A value of 0 resets the device to allow the control task to set the I/P (changing modes or a reset also switches back to normal control modes).
178	Input crnt snsr.
179	To calibrate or to check the 4-20mA current sensor.
180	Reset Cal Factory Defaults
181	Reset Calibration Data: This will restore all sensor calibration data to factory defaults. If calibrations have been performed they will be lost!
182	Reset Historian
183	Reset valve historian data (stroke count, cycle count, time open, time closed and time near closed ) to 0. The previous data is lost and must be recorded to be used later.
184	Reset SVi1000
185	This function performs a master reset to the device, causing it to go through its startup routine and re-initializing all of its operating parameters from non volatile memory.
186	Range error warning
187	Stop Procedure
188	Set Analog Output
189	User can set a fixed analog output of the position retransmitter.This is used only for checking loop wiring. Select Finished to return to position measurement function.
190	Re-transmitter Range
191	User can enter the upper and lower range values of valve position corresponding to output current 4 and 20 mA. The values typically are 0 and 100 %.
192	Read Device S/N
193	Read device and terminal board serial number.
194	Position Unit
195	Position Unit- Unit for valve position
196	DO Switch 1 Action
197	Define Switch 1 action.
198	Always Normal Pos
199	Failsafe
200	Tight Shutoff Active
201	Alarm Low
202	Alarm High
203	Manual Mode
204	DO Switch 1 Normally
205	Define Switch 1 is normally closed or open.
206	Closed
207	Open
208	DO Switch 1 Value
209	The value is set for alarm low/high.( Switch 1 Value must be between -99.99 and 199.99. ) Attention: This is valid under the condition of switch 1 type is alarm low/high), but to some host, like SDC-625, to activate this field maybe need to close / open this page again.
210	DO Switch 2 Action
211	Define Switch 2 action.
212	DO Switch 2 Normally
213	Define Switch 2 is normally closed or open.
214	DO Switch 2 Value
215	The value is set for alarm low/high.( Switch 2 Value must be between -99.99 and 199.99. ) Attention: This is valid under the condition of switch 2 type is alarm low/high, but to some host, like SDC-625, to activate this field maybe need to close / open this page again.
216	DI Switch Status
217	Digital Input Switch is enabled or disabled.
218	Disabled
219	Enabled
220	device busy
221	command not implemented
222	Mode(local)
223	Setup
224	Normal
225	Manual
226	cannot change mode
227	device malfunction
228	Fault Code 6
229	Reports Device
230	TM ID error
231	Terminal Module identification error
232	TM Data Integrity error
233	Retransmit Module Data Integrity Error
234	Fault Code 7
235	Fault Code 0 History
236	Reports Device History Errors
237	Fault Code 1 History
238	Fault Code 2 History
239	Fault Code 3 History
240	Fault Code 4 History
241	Fault Code 5 History
242	Fault Code 6 History
243	Fault Code 7 History
244	Clear Faults Type
245	Historic Faults
246	Total Travel
247	Total number of valve strokes.
248	Time Closed
249	Time in hours for valve closed.
250	h
251	Time Open
252	Time in hours for valve open.
253	Time Near Closed
254	Time in hours for valve near closed.
255	Number of Cycles
256	Number of cycles (direction changes).
257	Raw Signal
258	A/D value of the primary signal.
259	cts
260	5d
261	Raw Position
262	A/D value of the position sensor.
263	Raw Pressure
264	A/D value of the pressure sensor.
265	Lower Stop
266	Mechanical Stop without pressure in the actuator.
267	Upper Stop
268	Mechanical Stop with full pressure in the actuator.
269	Board Temperature
270	Internal SVi1000 temperature in °C.
271	Min Temperature
272	The lowest internal temperature recorded in °C.
273	Max Temperature
274	The upper internal temperature recorded in °C.
275	I/P Current
276	The actual I/P current, corrected for temperature
277	4.2f
278	3.1f
279	PWM output
280	PWM output.
281	DO Switch 1 State
282	DO Switch physical state (0 - closed; 1 - open)
283	DO Switch 2 State
284	Manual Setpoint
285	Manual Setpoint- Manual valve setpoint in %. Value must be between -5.0% and +160.0%.
286	6.2f
287	Set Valve Pos In mA
288	Manual Signal- Manual valve setpoint in mA.
289	5.2f
290	Setpoint Type
291	Setpoint Type- Selects how setpoint or signal is set.
292	Manual Signal (mA) value
293	Manual Position (%) value
294	Set Fully Closed
295	Set Fully Opened
296	Set To FailSafe
297	I/P Value
298	IP Value. A value of 0 resets the device to allow the control task to set the I/P (changing modes ora reset also switches back to normal control modes).
299	d
300	Local UI
301	LocalUI locking status.
302	Unlocked
303	Locked
304	Allow Override Limit
305	Allow diag. and self-tune to override limits
306	Tight Shutoff
307	Tight Shutoff Limit- Threshold for tight shutoff: when selected, if the input signal would position the valve below the tight shutoff value, full supply or atmosphere pressure is supplied to the actuator to close the valve with full seating force. Set the TS value between -1% and 20%, then enable the TS function.
308	Tight Shutoff Value
309	Tight Shutoff Limit- Threshold for tight shutoff: when selected, if the input signal would position the valve below the tight shutoff value, full supply or atmosphere pressure is supplied to the actuator to close the valve with full seating force. Value between -1% and 20% and not to include.
310	8.2f
311	Pos Limit Low
312	To enable or disable position lower limit
313	Pos Limit Upper
314	To enable or disable position upper limit
315	Limit Low
316	Lower Position Limit- The SVi1000 allows the user to establish software limit stops. The control functions will NOT allow the valve position to be lower than the lower position limit. However this option DOES NOT PROVIDE MECHANICAL STOPS for the valve. During an electrical or an air failure the valve will go to the failsafe position without regard to the software limit stops. The manual position full closed or full open will similarly ignore limit stops. The value should be set between -10 and 50.0 included
317	Limit Upper
318	Upper Position Limit- The SVi1000 allows the user to establish software limit stops. The control functions will NOT allow the valve position to be above than the upper position limit.However this option DOES NOT PROVIDE MECHANICAL STOPS for the valve. During an electrical or an air failure the valve will go to the failsafe position without regard to the software limit stops. The manual position full closed or full open will similarly ignore limit stops. the range should be limited from 10.0 to 110.0.
319	Set position limits
320	Set low/high limists for position.
321	save current parameters
322	Set Position Limits
323	Set the valve position low/high limits
324	Check signal range
325	Check signal range.
326	Rate Limit Down
327	Position Rate Limit Down Enable
328	Rate Limit Up
329	Postion Rate Limit Up Enable
330	Pos. Rate Limits
331	Position Rate Limits. The range shoud be between 0.8 and 100.10.
332	%/s
333	Bumpless Transfer
334	Bumpless Transfer- enables or disables the bumpless transfer mode.
335	Transfer Time
336	Transfer Time is approximately the number of seconds required to move the valve 100% toward the signal position. It is between 1 and 255 sec/100%.
337	sec/100%
338	3d
339	Characterization
340	Cam Configuration Flags- cam used - defines relationship between flow capacity (Cv) and percentage opening of the valve. Several cams are available: linear; =%50; =%30; quick opening coefficient of 50; custom; CamFlex=%.
341	Linear
342	Equal%(30)
343	Equal%(50)
344	Quick Open
345	Custom
346	Camflex%
347	Agressiveness
348	1i
349	cTuneFlags
350	The selections for autotune algorithm.
351	skips step 3 of tune algorithm
352	runs step 3 of tune algorithm
353	runs by default setting and skip step 3
354	runs by default setting with step 3
355	cTuneCompletionCode
356	cTuneCompletionCode(TBD)
357	Air Action
358	Air Action- configures the actuator to operate as Air to Close, or Air to Open.
359	Air to Close
360	Air to Open
361	Slot
362	Select the slot number(0-7), and load the specific tune data. Note: When the selector on the device indicates to 8 to F, means the device is configurated to ATC and the number of slots for ATC is still from 0 to 7.
363	slot 0
364	slot 1
365	slot 2
366	slot 3
367	slot 4
368	slot 5
369	slot 6
370	slot 7
371	P
372	Proportional gain in %. Common values are 50 for small valves up to 4000 for large valves. Must be between 0 and 5000.
373	4d
374	I
375	Integral time or reset time in 1/10 s. Higher values of I cause less integral action, however a value of 0 gives no integral action. Common values are 10 to 200. Values between 0 and 1000.
376	(1/10s)
377	D
378	Derivative time or rate time in milliSeconds. Common values are 10 to 100. Values between 0 and 200.
379	mS
380	Padj
381	Coefficient added to P when the valve is exhausting and compensates the variation in filling and exhausting speed. Can be positive or negative value range between -3000 to +3000.
382	Beta
383	Nonlinear gain factor. When beta is 0, the proportional gain is linear, otherwise the gain P is a function of error. The larger the beta, the smaller the gain for small error. Typical beta value is 7 or 8. Beta is ranging from -9 to +9.
384	Position Comp.
385	The response of the valve is different when the valve is nearly closed than when nearly open. This coefficient allows the user to make adjustments to try to equalize the valve response. Normal value is 6 and this value is ranging from 2 to 20.
386	2d
387	Dead Zone
388	When the valve position is within the setpoint +/- the dead zone and, no additional position control is performed. This value is normally 0%. Used to avoid limit cycling for high friction valves. Range is 0 to 5%.
389	Non Linear
390	Active PID slot
391	Current active PID parameters
392	PID selector from hardware setting
393	ATO/ATC from hardware setting
394	wrong mode
395	Open Stop Adj
396	Open Stop Adjustment- This value must be between 60%-100%.For some valves the open position stop exceeds the nominal travel of the valve.By entering a value, the position calibration can be adjusted to nominal travel.
397	5.1f
398	Boost
399	Boost- Compensates for the pnuematic dead band. Value ranges between 0 and 20.
400	Reserved 1
401	Auto Tune Fault
402	Reason for Auto Tune failure
403	Pos Error Band
404	Position Error Band- Value corresponding to the maximun error (in % opening) between the setpoint and the valve position allowed, before setting a status flag regards the selection of associated variable Time. Value must be between 0.5% and 200.0% .
405	Pos Error Enable
406	Enable Position Error- enable position error testing
407	Pos Error Time
408	Position Error Time- time before to set the warning when position error exceeds the configured position error limit. This time must be between 0 s and 327 s.
409	s
410	Position Fail
411	Enable Position Fail- enable position fail testing
412	Pos Fail Time
413	Position Fail Time- Time before to put the valve in failsafe mode. This time must be >= 0 s and below 328 s and in any case 2s greater than Time 1 However to inhibit failsave mode set -1 s.
414	Near Closed Value
415	Near Closed Position- Value of valve position below which the user considers the valve as being near closed position. Used in continuous diagnostic calculations. Must be between 0 and 20%.
416	Stop Adjust Flag
417	Low
418	High
419	find stops failed
420	Low Signal
421	Low Input Signal- Lower range value of input signal for valve closed (direct acting) or lower range value of input signal for valve open (reverse acting). Must be between 3.8 mA and 14 mA.
422	mA
423	High Signal
424	High Input Signal- high input signal for valve open (direct acting) or high input signal for valve closed (reverse acting). Must be between 8 mA and 20.2 mA. The difference between Lower Range Value and Upper Range Value (span) must be at least 5 mA.
425	Set signal range
426	Set Signal range value.
427	Set the signal range
428	Set the low/high input signal
429	Select Storage
430	Selects which curve the recently created valve signature is stored to
431	Not Saved
432	Saved
433	Baseline
434	Calibration Sensor
435	Signal
436	Calibration Type
437	Calibration Value
438	The current value of the signal being calibrated.
439	calibration failed
440	Diag. Test Type
441	Step Response Test
442	Std. Actuator Sig.
443	Speed Level
444	Valve speed motion for recording data. Min is 1 and max is 10.
445	Start Pos
446	Start Position
447	End Pos
448	End Position
449	Sample Rate
450	Diag Param 2
451	Diag Param 3
452	diagnostics not allowed
453	Option Config 0
454	Pressure Sensor 1
455	Pressure Sensor 2
456	Pressure Supply
457	Input/Output Switches
458	Retransmit Output
459	Model
460	System Version-Positioner function level.
461	Undefined
462	ES - EZ Smart
463	SD - Standard Diag
464	AD - Advanced Diag
465	DP - Diagnostics Plus
466	ESD
467	Option Config 1
468	Remote Position Sensor
469	Single Acting
470	Process Variable Input
471	Reserved
472	Active Position Sensor
473	Position Sensor- built-in or remote position sensor.
474	Hall Sensor
475	Remote Sensor
476	I/P Type
477	I/P Type- defined within Option Config 2
478	Relay Type
479	Relay Type- defined within Option Config 2
480	Option Config X
481	Actuator Press. 1
482	Actuator Port Pressure 1
483	Actuator Press. 2
484	Actuator Port Pressure 2
485	Air Supply Pressure
486	I/P Pressure
487	Atm Pressure
488	Atmospheric Pressure
489	20mA signal at a travel of
490	Position in % at 20mA for position retransmitter
491	7.2f
492	4mA signal at a travel of
493	Position in % at 4mA for position retransmitter
494	X1
495	X defines signal input in % and Y defines position value in % The min and max values are respectively 4.0% and 100.0% The custom curve must have at least one pair. A coordinate (100.0%,100.0%) indicates the end of the curve.
496	Y1
497	X defines signal input in % and Y defines position value in % The min and max values are respectively 0.0% and 100.0% The custom curve must have at least one pair. A coordinate (100.0%,100.0%) indicates the end of the curve.
498	X2
499	Y2
500	X3
501	Y3
502	X4
503	Y4
504	X5
505	Y5
506	X6
507	Y6
508	X7
509	Y7
510	X8
511	Y8
512	X9
513	Y9
514	X10
515	Y10
516	Signal A/D
517	Value of Signal A/D
518	2nd Signal A/D
519	Temperature A/D
520	Temperature A/D value
521	Atm Press A/D
522	Atm Pressure AD value
523	Rem Pos A/D
524	Remote Position A/D value
525	Supply Press A/D
526	Supply Pressure A/D value
527	Hall Sensor A/D
528	Hall Sensor A/D value
529	Act Press 1 A/D
530	Acutuator Pressure 1 A/D value
531	Act Press 2 A/D
532	Actuator Pressure 2 A/D value.
533	Pilot Press A/D
534	Pilot Pressure A/D value.
535	I/P Current A/D
536	I/P current A/D value.
537	Ref Voltage A/D
538	Reference voltage A/D value.
539	Signal value after factory temperature correction.
540	the 2nd Signal value after factory temperature correction.
541	Temperature A/D value after factory temperature correction.
542	Atm pressure value after factory temperature correction.
543	Remote Position value after temperature correction
544	Supply pressure value
545	Hall sensor value
546	Actuator pressure 1 value
547	Actuator Pressure 2 value
548	Pilot pressure value
549	I/P current value
550	Reference voltage value
551	SubMode
552	SubMode - SVi1000 out-of-service modes can be: setup, low power, failsafe. SubMode is only valid when Mode is Out-Of-Service.
553	This mode allows the user to describe the basic valve setup,to perform calibration and diagnostic.
554	Fail Safe
555	It is the positioner security mode when critical faults occurs or in case of position error with time 2 activated.
556	Mode
557	Mode - SVi1000 modes can be: out-of-service (setup, low power, fail safe, fail safe LP), normal, or manual.
558	This mode allows the user to describe the basic valve setup, to perform calibration and diagnostic.
559	Fail Safe with Low Power
560	Fail safe with Low Power
561	Out-Of-Service
562	Out of service
563	In the normal operating mode,the positioner responds to the 4-20 mA input signal and positions the valve appropriately.
564	In the manual mode, the valve no longer responds to the 4-20mA and is locked in place.The position may be changed manually from the buttons or by send a HART command.
565	Process Busy
566	Percent Complete
567	Analog Output
568	Analog Output - fixed value to set for position retransmitter. Set to 0 will put the retrasmitter out of the fixed output mode.
569	Unused(int3)
570	fPressMin
571	fPressMax
572	LED State
573	State of LED
574	Rotary Switch State
575	Push Button Edges
576	the Pushbutton became pressed
577	the Pushbutton became released
578	Push Button State
579	Pressed
580	Not pressed
581	Quad Encoder Step
582	Terminal Board
583	No Card
584	DO Card is installed
585	Retransmit Card is installed
586	DO 1 Hardware State
587	Close
588	DO 2 Hardware State
589	Terminal Module Serial Number
590	BoardID Signature
591	Family
592	SVi1000 Module
593	Group
594	Module
595	Retransmit
596	Version
597	Read Custom Characterization Data
598	Select characterization. If Custom is selected then continue to set custom points.
599	Edit
600	Current
601	History
602	Instrumentation
603	Actuator
604	Critical
605	Pneumatics
606	Electronics
607	Device Faults
608	Device Configuration
609	Device Diagnostics
610	characterization
611	SVi1000 Retransmit
612	SVi1000 Switches
613	Sig.
614	Input signal in current: 4.0 - 20.0 mA
615	Input signal in percent: 0 - 100%
616	Pos.
617	Valve position in percent: 0 - 100%
618	Manual SP.
619	Manual Setpoint in percent: -5.0 - 160.0%
620	Y-Axis: 0 - 100%
621	Input signal 0-100%
622	Manual SetPoint
623	Valve Position3
624	Trend
625	STRIP0
626	STRIP1
627	STRIP2
628	The chart for valve position and manual set position
629	Position Bar
630	Signal Bar
631	Monitor
632	SVi1000 HART
633	Setup Wizards
634	Valve Travel Tuning
635	Auto tune
636	Custom Characterization
637	Input Signal(%)
638	Position Value(%)
639	Charc Curve
640	Characterization Curve. Please use method Custom / Standard Characterization for editing custom characterization.
641	Characterization Curve
642	Graph of Characterization Curve, The X-axis is for input signal(%) and Y-axis is for valve position(%).
643	Device Status
644	Clear Faults
645	Continuous Diagnostics
646	Raw data
647	Main signal
648	What is Current Mode?
649	What is Current Mode? - To get the current mode of this device
650	Enable on token-passing data link layer only
651	Enable on TDMA data link layer only
652	Enable on both TDMA and token-passing data link layer
653	Wireless
654	WirelessHART Device
655	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
656	Primary
657	Primary Analog Channel
658	Secondary
659	Secondary Analog Channel
660	Tertiary
661	Tertiary Analog Channel
662	Quaternary
663	Quaternary Analog Channel
664	Quinary
665	Quinary Analog Channel
666	Critical Power Failure
667	Lock all
668	Trim not supported
669	Configuration cannot be changed
670	Locked by gateway
671	Analog Input Channel
672	Analog Output Channel
673	Secondary Analog Channel Saturated
674	Tertiary Analog Channel Saturated
675	Quaternary Analog Channel Saturated
676	Quinary Analog Channel Saturated
677	Secondary Analog Channel Fixed
678	Tertiary Analog Channel Fixed
679	Quaternary Analog Channel Fixed
680	Quinary Analog Channel Fixed
681	Wired HART Enabled
682	Enabled on Wired HART device connection only
683	Wireless HART Enabled
684	Enabled on WirelessHART device connection only
685	Both Wired and WirelessHart Enabled
686	Enabled on both Wired and WirelessHART connections
687	8.3f
688	8u
689	Select the slot to read:
690	Firmware Version - %{0}.%{1}.%{2}
691	This DD is tokenized by version 8 65cc0201.ddl's Time-stamp: <2015-05-24 11:27:14>
692	Warning: To restore from %{0} mode, please clear faults first, Otherwise it will cause unexpected result!
693	Continue;Exit
694	Set Mode Target
695	Normal;Manual;Setup
696	WARNING. Leaving Normal Mode will result in LOSS of process CONTROL and may cause sudden valve move. DO YOU WISH TO CONTINUE?
697	Procedure aborted Try Again.
698	WARNING. This procedure requires to enter setup mode and will result in LOSS of PROCESS CONTROL. Do you wish to proceed ?
699	Changing mode to Setup
700	WARNING. This procedure will MOVE the valve. This will result in LOSS of process CONTROL. DO YOU WISH TO CONTINUE?
701	Please wait while searching for mechanical stops. This should take approximately 30 seconds. Press OK to continue.
702	Please Wait ...
703	Press the ABORT key to abort the process.
704	Find stop limits FAILED.
705	Please verify that: - Air supply is sufficient; - The valve is not handjacked; - The mounting is adequate; - The find stop is not allowed in marginal status; - The find stop is not allowed in lower power status;
706	Please verify that (Continued): - The Travel Sensor is set properly. Then re-run find stops again.
707	Find stop limits completed.
708	The device was configured as ATO valve, so current PID selector must be at 0 position to do autotune!
709	The device was configured as ATC valve, so current PID selector must be at 8 position to do autotune!
710	Remove software limit stops to be able to perform autotune.
711	Agressiveness:
712	0;9;8;7;6;5;4;3;2;1;-1;-2;-3;-4;-5;-6;-7;-8;-9
713	Enter the Supply pressure in psi
714	Error: Supply pressure is out of range. Enter again!
715	Please wait while searching for optimal valve tuning parameters. This should take approximately 3 to 6 minutes.
716	Auto Tune FAILED!
717	Auto Tune completed.
718	This mode is not appropriate for the Setup Wizard. Click OK to change mode or Abort to exit Setup Wizard.
719	Find Valve Stops:
720	Skip This Task;Run Find Stops
721	Auto Tune:
722	Skip This Task;Run Auto Tune
723	Enter the Supply pressure
724	Auto Tune FAILED.
725	Reset to Factory Default:
726	Skip This Task;Set All Values to Default
727	Are you sure you want to reset all data to factory defaults?
728	Reset to Factory Defaults completed.
729	No faults recorded.
730	Do you want to clear current faults ?
731	No;Yes
732	Device has malfunctioned
733	Faults have been cleared.
734	No Historic Faults.
735	Do you want to clear all faults ?
736	The device must not be in NORMAL mode to perform this operation. Please change the device mode.
737	WARNING! This command strokes the valve and should not be performed with process running.
738	Manual Setpoint:
739	Set By Position;Set By Signal
740	Valve Position (-5% ~ 160%):
741	Position Corresponding to Signal in mA:
742	Select Tight Shutoff
743	Apply new changes to the device? Press: OK for YES ABORT for NO
744	Select Cam
745	Enter/edit cam characterization ?
746	Input your 9 XY pairs of points between (0.0%, 0.0%) and (100.0%,100.0%).
747	X[%{i}]
748	Y[%{i}]
749	Invalid segment: X%{a} = %{0}, X%{i} = %{1} - Same X.
750	Invalid segment: X0=0, X%{i}=%{0} - Slope too low.
751	Invalid segment: X%{a}=%{0}, X%{i}=%{1} - Slope too low.
752	Invalid segment: X0=0, X%{i}=%{0} - Slope too high.
753	Invalid segment: X%{a}=%{0}, X%{i}=%{1} - Slope too high.
754	Invalid segment: X%{a}=%{0}, X%{i}=%{1} - Slope changes too much.
755	Invalid segment: X%{a}=%{0}, X%{i}=%{1} - Slope changes too small.
756	Found bad segment(s), please choose:
757	Enter data again to correct error(s); Abort the method; Proceed to save without correction.
758	Set Manual Stop Position:
759	Low;High;Exit
760	Wait until the valve is stable, then press OK.
761	Procedure failed. The stroke could be too small.
762	Open Stop Adjustment set properly.
763	The current active PID slot is not at 0, following process only set the PID parameters for slot 0.Press OK to continue!
764	slot = 0 P = %{0} % I = %{1} (1/10s) D = %{2} ms Padj = %{3} %
765	Beta = %{4} Compens. pos.= %{6} Dead zone = %{7} % Boost = %{8}
766	P (%)
767	I (1/10s)
768	D (ms)
769	Padj (%)
770	Compensation
771	Dead Zone (%)
772	Set the I/P Value(0~65535):
773	WARNING. This procedure requires to enter setup mode. Please change to setup mode first.
774	Enter the low signal value between 3.5 and 8.0 mA:
775	The value must be between 3.5 and 8.0 mA
776	Set the input current to %[.2f]{0} mA and press OK
777	The current is not set correctly! Please check and set again.
778	Enter the high signal value between 16.0 and 21.0 mA:
779	The value must be between 16.0 and 21.0 mA
780	WARNING. To continue this procedure will reset calibration data to factory defaults. DO YOU WISH TO CONTINUE?
781	Calibraton data have been reset to factory defaults.
782	After resetting, the current values will be lost. Press ABORT if you do not wish to proceed.
783	Valve Historian data was reset.
784	A reset may cause the valve to move ! Perform a RESET?
785	Reset on SVi1000 did NOT correctly execute.
786	Reset on SVi1000 correctly executed.
787	Error: Lower(%[.3f]{0}) and upper(%[.3f]{1}) ranges must differ by at least 5%.
788	Limit Upper (%[.3f]{1} %) must be greater than Limit Low (%[.3f]{0} %) Please enter the value again!
789	High Signal (%[.2f]{1} mA) must be at least 5mA larger than Low Signal (%[.2f]{0} mA) Please enter the value again!
790	The lower value(%{0} %) must lower than upper value(%{1} %) Please enter the value again!
791	Interrupting the current process.
792	The process was interrupted.
793	The position retransmitter has restored to the normal control mode of following the position.
794	There is no position retrasmitter for this device.
795	Setting analog output is disabled when device is in the %{0} mode
796	Set current output of the position retransmitter:
797	Set Output in mA;Finished
798	Set Output in 4 - 20 mA:
799	Change output range is disabled when device is in the %{0} mode
800	Lower Range in %
801	Upper Range in %
802	Error: Lower and upper ranges must differ by at least 5%.
803	Set re-transmitter range is done.
804	The main board serial number is: %[d]{nSerialNumber} The Position Retransmit board serial number is: %[d]{nTerminalNumber}
805	The main board serial number is: %[d]{nSerialNumber}
806	The both of position limits are disabled, No position limits can be set.
807	Enter the lower limit value(-10.0%, 50.0%):
808	Enter the upper limit value(10.0%, 110.0%):
809	The new lower limit(%{0}%) is greater more than upper limit(%{1}%)
810	No accept, quit;Re-enter the limits
811	The new limits:%{0}%, %{1}%
812	Accept new limits;Re-enter the limits;No accept, quit
813	Enter the low input current(3.8mA, 14.0mA):
814	Enter the high input current(8.0mA, 20.2mA):
815	High Signal (%[.2f]{1} mA) must be at least 5mA larger than Low Signal (%[.2f]{0} mA)
816	No accept, quit;Re-enter the range
817	The new signal range:%{0}mA, %{1}mA
818	Accept new range;Re-enter the range;No accept, quit
819	Device is currently in NORMAL mode.
820	Device is currently in MANUAL mode.
821	Device is currently in SETUP mode.
822	Device is currently in LOW POWER mode.
823	Device is currently in FAILSAFE mode.
824	Device is currently in OOS mode.
825	Device Mode Unknown.
引用ID	字符串