Device dictionary

Loading…

Reference ID	String
0	Model
1	Model- References the type of field Device, usually an advertised model number, that is unique to a single manufacturer.
2	SVI II AP
3	Manufacturer
4	Manufacturer Identification Code- References a specific manufacturer, which is usually a company name, that is responsible for the manufacture of this Field Device.
5	Masoneilan-DRESSER
6	Nbr Of Preambles
7	Number of Request Preambles- Number of Preambles required from the Host request by the Field Device.
8	Univ Cmd Rev
9	Universal Revision- Revision of the Universal Device Description, to which the Field Device conforms to.
10	Trans Cmd Rev
11	Field Device Revision- Revision of the Field Device Specific Device Description, to which the Field Device conforms to.
12	Software Rev
13	Field Device Software Revision- This revision corresponds to the software or firmware, that is embedded in the Field Device.
14	Hardware Rev
15	Hardware Revision- Revision that corresponds to the electronics hardware of the Field Device.
16	Phys Sign Code
17	Physical Signaling Code- The Physical Signaling Code describes the type of Physical Layer that has been implemented in the hardware that is responsible for the HART Communication port.
18	Device Flags
19	Field Device Flags- Describes special features of the Field Device that affect the Data Link Layer.
20	Device ID
21	Field Device Identification- Uniquely identifies the Field Device when combined with the Manufacturer Identification and Device Type. Therefore, this variable cannot be modified by the Host user.
22	Poll Addr
23	Polling Address- Address used by the Host to identify a Field Device, and changeable by the User to control the Multidrop Mode.
24	Tag
25	Tag- Text that is associated with the Field Device installation. This text can be used by the user in any way. A recommended use is as a unique label to a plant that correlates to a Field Device label: on a plant drawing, or on a Control System. This variable is also used as a type of data link layer address handle.
26	Message
27	Message- Text that is associated with the Field Device. This text can be used by the user in any way. There is no recommended use.
28	Descriptor
29	Descriptor- Text that is associated with the Field Device. This text can be used by the user in any way. There is no specific recommended use.
30	Date
31	Date- Gregorian calendar date that is stored in the Field Device. This date can be used by the user in any way. There is no specific recommended use. Enter MM/DD/YY
32	Final Asmbly Nbr
33	Final Assembly Number- Number that is used for identification purposes, and is associated with the overall Field Device.
34	Response Code
35	Device Status
36	Burst Command Number
37	Burst Mode Select- If set ON, will allow 3 refreshs per second without Master request. This function is sometime incompatible with DCS or PC software use.
38	Burst Mode Select
39	Reports Device Errors
40	Fault Code 0
41	Reset
42
43	Low Power
44	Actuator Error
45	Air Supply Low
46	Position Error
47	Reserved (0-5)
48	Keypad Fault
49	Marginal Power
50	Fault Code 1
51	Calibration Failed
52	Find Stops Failed
53	Autotune Failed
54	Std Diagnostics Failed
55	Ext Diagnostics Failed
56	Operating System Fault
57	Reserved (1-6)
58	Reserved (1-7)
59	Fault Code 2
60	Bias Out Of Range
61	I/P Out Of Range
62	Temp Out Of Range
63	Reserved (2-3)
64	Reserved (2-4)
65	Reserved (2-5)
66	Reserved (2-6)
67	Reserved (2-7)
68	Fault Code 3
69	NVM Checksum Error
70	RAM Checksum Error
71	Flash Checksum Error
72	Stack Error
73	Factory Mode Fault
74	NVM Test Error
75	Reserved (3-6)
76	Reserved (3-7)
77	Fault Code 4
78	Ref Voltage Fault
79	Position Sensor Fault
80	Current Sensor Fault
81	Temperature Sensor Fault
82	Reserved
83	Actuator Pressure 1 Fault
84	Actuator Pressure 2 Fault
85	Supply Pressure Sensor Fault
86	Fault Code 5
87	I/P Pressure Sensor Fault
88	Atmospheric Pressure Sensor Fault
89	NVW Write Fault
90	IRQ Fault
91	Self Check Error
92	Software Error
93	Quick Access Key
94	Online (SVI II AP)
95	Device Setup
96	Process Variables
97	Status/Diagnostics
98	Calibration
99	Commissioning Services
100	Basic Info.
101	Position Retransmit
102	Valve Travel
103	Manual Position Setpoint
104	Manual Setup
105	Actuator Type
106	Sensors
107	Status/Faults
108	Fault List
109	display current and historic faults
110	Valve Historian
111	Signature
112	Sensor Measurements
113	I/P
114	Read Pressures
115	Temperature
116	Raw Sensor Data
117	Valve Tuning Data
118	Alarms Setup
119	I/O's
120	Switches
121	General
122	Device Info
123	Hart Info
124	Information for HART
125	Configuration
126	Positioning
127	Limits/Shutoff
128	HART
129	Valve Pos
130	Position- Indicates the actual valve position in % with closed = 0 % and opened = 100 %
131	Actual Pressure
132	Pressure- Indicates the actual valve pressure in its engineering unit. Units may be psi, bar, or kPa.
133	Input
134	Input Signal- Input signal (current loop) in percent
135	Analog
136	Analog Inputs- Input signal (current loop) in mA
137	Valve Position
138	Valve Position- Indicates the actual valve position in % with closed = 0 % and opened = 100 %
139	%
140	.1f
141	Pressure
142	Pressure- Indicates the actual valve pressure in its engineering unit.
143	.2f
144	.3f
145	internal_use
146	Input Signal
147	Signal- Input signal and current loop in mA
148	Input Percent Range- Input signal (current loop) in percent
149	7d
150	Unused
151	Pressure Unit from command 3
152	Pressure Unit for sv- The actual pressure reported by the SVI II AP can be in psi, bar or kPa(for sv)
153	Not_Used
154	fill
155	Firmware Version
156	Display the firmware version.
157	Change Mode
158	Change mode: Changes the mode to Normal Mode, Manual Mode, or Setup Mode. Normal Mode: The position setpoint follows the input signal. Always return to Normal Mode to return to Control by the Control System. Manual Mode: The position setpoint remains at the last position prior to entering Manual Mode. Position setpoint may adjusted with the local pushbuttons or by HART commands. Setup Mode: The position setpoint remains at the last position prior to entering Setup Mode. Use this mode to change configuration and calibration information.
159	Find Stops
160	Run automatic find stops will establish the calibration position of the valve at actuator pressure vented and at full supply pressure.
161	Autotune
162	Run PID Autotune will automatically find best dynamic parameters for responsive valve positioning. Always isolate the valve from the process. The valve will move full open and full closed. The valve will continuously change position for about 5 minutes.
163	Setup Wizard
164	The setup wizard will guide you through basic steps to setup the positioner on an actuator. You may skip this wizard if the valve and positioner have been factory configured and calibrated. Always isolate the valve from the process. The wizard allows setting Air Action. The valve move full open and full closed. You will be prompted if mode must be changed. The steps are in the following order: 1. Set Air action to Air to Open or Air to Close; 2. Run Find Stops, to set 0% to the valve closed position and to set 100% to full opened position. 3. Run Auto Tune to determine best dynamic parameters for position control. 4. Reset Basic Configuration and Calibration to Factory Defaults.
165	Reset Basic Config and Cal To Defaults
166	The Reset to Factory Default will set the following list of configuration and calibration parameters to defaults: Air Action is set to ATO; All PID tuning parameters are set to defaults; Input current range is set to 4 to 20 mA; Open stop adjustment is set to 100%; Position error parameters are reset and disabled; Bumpless transfer is disabled; Position limits are disabled; Tight shutoff is set to 0.5% and enabled; Characterization is set to linear; Pressure units and language are set to psi and English; Button Locks = None; Controller = None;
167	Current Faults
168	Read the device's current faults.
169	Read/Clear Faults
170	Read the device's current faults. Optionally, the fault status may also be cleared.
171	Clear Current Faults
172	Clear the current device status/faults
173	Historical Faults
174	Read the device's historical faults.
175	Clear All Faults
176	Clear the historic and current device faults/status.
177	Set Position
178	Set manual valve setpoint in % or set the position by equivalent input current to simulate non-linear characterization and limits.
179	Full Open
180	Fully Open valve
181	Full Close
182	Fully Close Valve
183	Configure Wizard
184	Change configuration of Limit Override, Tight shutoff, Pressure units, Language, Button Locks, Air Action, and Near Closed Value. Limit Overrideallows Find Stops, Autotune and Diagnostics to override position limits.
185	Custom / Standard Characterization
186	Control valves are often characterized to give a specific relationship between flow capacity (Cv) and percent opening of the valve. The valve can be characterized with special purpose trim or with the SVI2AP positioner. Selecting Custom Configuration displays an additional screen where the user can enter a custom characterization curve to fit his/her needs. The curve can have up to 9 points and points in between are linearly interpolated.
187	Set Analog Output
188	User can set a fixed analog output of the position retransmitter.This is used only for checking loop wiring. Select Finished to return to position measurement function.
189	Re-transmitter Range
190	User can enter the upper and lower range values of valve position corresponding to output current 4 and 20 mA. The values typically are 0 and 100 %.
191	Manual Stops
192	This method is used to set manual stops.
193	Open Stop Adjustment
194	Open stop adjustment; Allows to adjust travel to less than mechanical limits. Must be between 60% and 100% of mechanical travel set with Find Stops.
195	Manual Tuning
196	The user can set tuning PID coefficients.
197	Stroke Time
198	set stroke time. Stroke time is used to limit rate of change of travel. Stroke time is expressed as sec/100% travel
199	Set I/P Output
200	set I/P output.
201	Input Current Sensor
202	To calibrate or to check the 4-20mA current sensor.
203	Pressure Sensor
204	This operation will change zero calibration of all available pressure sensors .
205	To read pressures.
206	Reset Cal Factory Defaults
207	Reset Calibration Data: This will restore all sensor calibration data to factory defaults. If calibrations have been performed they will be lost!
208	Run Diagnostics
209	Perform valve signature and valve functional analysis. Displays the diagnostic test results.
210	Reset Historian
211	Reset valve historian data (stroke count, cycle count, time open, time closed and time near closed ) to 0. The previous data is lost and must be recorded to be used later.
212	Reset SVI II AP
213	This function performs a master reset to the device, causing it to go through its startup routine and re-initializing all of its operating parameters from non volatile memory.
214	Stop Procedure
215	Position Unit
216	Position Unit- Unit for valve position
217	DO Switch 1 Normally
218	Define Switch 1 is normally closed or open.
219	Closed
220	Open
221	DO Switch 2 Normally
222	Define Switch 2 is normally closed or open.
223	DO Switch 1 Action
224	Define Switch 1 action.
225	Always Normal Pos
226	Failsafe
227	Tight Shutoff Active
228	Position Low Limit
229	Position Upper Limit
230	Manual Mode
231	DO Switch 2 Action
232	Define Switch 2 action.
233	Disabled
234	Enabled
235	disble the fswitch1value, and fswitch2value
236	DO Switch 1 Value
237	The value is set for Position Low / Upper Limits.( Switch 1 Value must be between 0 and 200. ) Attention: This is valid under the condition of switch 1 type is Posistion Low/High Limit ), but to some host, like SDC-625, to activate this field maybe need to close / open this page again.
238	5.2f
239	DO Switch 2 Value
240	The value is set for Position Low / Upper Limits.( Switch 2 Value must be between 0 and 200. ) Attention: This is valid under the condition of switch 2 type is Posistion Low/High Limit, but to some host, like SDC-625, to activate this field maybe need to close / open this page again.
241	DI Switch Status
242	Digital Input Switch is enabled or disabled.
243	device busy
244	wrong mode
245	find stops failed
246	command not implemented
247	Mode
248	Mode - SVI II AP modes can be: out-of-service (setup, low power, fail safe, fatal), normal, or manual.
249	Setup
250	This mode allows the user to describe the basic valve setup, to perform calibration and diagnostic.
251	????
252	Fail Safe
253	It is the positioner security mode when critical faults occurs or in case of position error with time 2 activated.
254	Fatal
255	Out-Of-Service
256	?????
257	Normal
258	In the normal operating mode,the positioner responds to the 4-20 mA input signal and positions the valve appropriately.
259	Manual
260	In the manual mode, the valve no longer responds to the 4-20mA and is locked in place.The position may be changed manually from the buttons or by send a HART command.
261	device malfunction
262	Fault Code 0 History
263	Reports Historic Device Errors
264	Fault Code 1 History
265	Fault Code 2 History
266	Fault Code 3 History
267	Fault Code 4 History
268	Fault Code 5 History
269	Clear Faults Type
270	Historic Faults
271	Total Travel
272	Total number of valve strokes.
273	strokes
274	10d
275	Time Closed
276	Time in hours for valve closed.
277	h
278	Time Open
279	Time in hours for valve open.
280	Time Near Closed
281	Time in hours for valve near closed.
282	Number of Cycles
283	Number of cycles (direction changes).
284	cycles
285	Raw Signal
286	A/D value of the primary signal.
287	cts
288	5d
289	Raw Position
290	A/D value of the position sensor.
291	Raw Pressure
292	A/D value of the pressure sensor.
293	Lower Stop
294	Mechanical Stop without pressure in the actuator.
295	Upper Stop
296	Mechanical Stop with full pressure in the actuator.
297	Board Temperature
298	Internal SVI II AP temperature in °C.
299	Min Temperature
300	The lowest internal temperature recorded in °C.
301	Max Temperature
302	The upper internal temperature recorded in °C.
303	I/P Current
304	The actual I/P current, corrected for temperature
305	4.2f
306	3.1f
307	DO Switch 1 State
308	State is: open = 0 and closed = 1
309	DO Switch 2 State
310	I/P Switch State
311	State is: open = 1 and closed = 0
312	DI Switch State
313	Manual Setpoint
314	Manual Setpoint- Manual valve setpoint in %. Value must be between -5.0% and +160.0%.
315	6.2f
316	Set Valve Pos In mA
317	Manual Signal- Manual valve setpoint in mA.
318	Setpoint Type
319	Setpoint Type- Selects how setpoint or signal is set.
320	Manual Signal (mA) value
321	Manual Position (%) value
322	Set Fully Closed
323	Set Fully Opened
324	Set To FailSafe
325	Internal used
326	I/P Output
327	Set constant current on the I/P to adjust the pneumatic block.
328	Air Action
329	Air Action- configures the actuator to operate as Air to Close, or Air to Open.
330	Air to Close
331	Air to Open
332	Bumpless Transfer
333	Bumpless Transfer- enables or disables the bumpless transfer mode.
334	Allow Override Limit
335	Allow diag. and self-tune to override limits
336	Pos Limit Low
337	To enable or disable position lower limit
338	Pos Limit High
339	To enable or disable position upper limit
340	Tight Shutoff
341	Tight Shutoff Limit- Threshold for tight shutoff: when selected, if the input signal would position the valve below the tight shutoff value, full supply or atmosphere pressure is supplied to the actuator to close the valve with full seating force. Set the TS value between -1% and 20%, then enable the TS function.
342	Characterization
343	Cam Configuration Flags- cam used - defines relationship between flow capacity (Cv) and percentage opening of the valve. Several cams are available: linear; =%50; =%30; quick opening coefficient of 50; custom; CamFlex=%.
344	Linear
345	Equal%(30)
346	Equal%(50)
347	Quick Open
348	Custom
349	Camflex%
350	Local Buttons
351	Button Configuration Flags- Defines lock level for SVI II AP buttons to avoid unintended modifications.
352	All Enabled
353	Define lock level :no restriction
354	No Config/Cal
355	Define lock level :lock out local config, calibrate and diagnostic menu
356	No Manual
357	Define lock level :lock out local manual menu
358	Locked
359	Define lock level :lock out all buttons
360	Setpoint Mode
361	Setup Configuration Flags- These options determine whether the controller setpoint will be in local, local only, remote or last mode on startup.
362	PV Local Only
363	PV Startup Remote
364	PV Startup Last
365	SP Local Only
366	SP Statup Remote
367	SP Startup Last
368	LC Direct
369	LC Ratio Control
370	Tight Shutoff Value
371	Tight Shutoff Limit- Threshold for tight shutoff: when selected, if the input signal would position the valve below the tight shutoff value, full supply or atmosphere pressure is supplied to the actuator to close the valve with full seating force. Value between -1% and 20% and not to include.
372	4.1f
373	Tight Shutoff Limit Check
374	Limit Low
375	Lower Position Limit- The SVI II AP allows the user to establish software limit stops. The control functions will NOT allow the valve position to be lower than the lower position limit. However this option DOES NOT PROVIDE MECHANICAL STOPS for the valve. During an electrical or an air failure the valve will go to the failsafe position without regard to the software limit stops. The manual position full closed or full open will similarly ignore limit stops. The value should be set between -10 and 50.0 not to include
376	5.1f
377	Position Limit Check
378	Limit High
379	Upper Position Limit- The SVI II AP allows the user to establish software limit stops. The control functions will NOT allow the valve position to be above than the upper position limit.However this option DOES NOT PROVIDE MECHANICAL STOPS for the valve. During an electrical or an air failure the valve will go to the failsafe position without regard to the software limit stops. The manual position full closed or full open will similarly ignore limit stops.
380	Transfer Time
381	Transfer Time is approximately the numberof seconds required to move the valve 100%toward the signal position. It is between 1 and 255 sec/100%.
382	sec/100%
383	3d
384	Transfer Time Check
385	Stroking Limit
386	s
387	Pressure Unit
388	Pressure Unit- The actual pressure reported by the SVI II AP can be in psi, bar or kPa
389	LCD Language
390	Language Displayed- Choice of languages displayed on the SVI II AP LCD.
391	English
392	Possibility of different languages displayed on the SVI II AP LCD
393	French
394	Open Stop Adj
395	Open Stop Adjustment- This value must be between 60%-100%.For some valves the open position stop exceeds the nominal travel of the valve.By entering a value, the position calibration can be adjusted to nominal travel.
396	Close Stop Adj
397	Close Stop Adjustment- NOT IMPLEMENTED YET
398	P
399	Proportional gain in %. Common values are 50 for small valves up to 4000 for large valves. Must be between 0 and 5000.
400	4d
401	I
402	Integral time or reset time in 1/10 s. Higher values of I cause less integral action, however a value of 0 gives no integral action. Common values are 10 to 200. Values between 0 and 1000.
403	(1/10s)
404	D
405	Derivative time or rate time in milliSeconds. Common values are 10 to 100. Values between 0 and 200.
406	mS
407	Padj
408	Coefficient added to P when the valve is exhausting and compensates the variation in filling and exhausting speed. Can be positive or negative value range between -3000 to +3000.
409	Beta
410	Nonlinear gain factor. When beta is 0, the proportional gain is linear, otherwise the gain P is a function of error. The larger the beta, the smaller the gain for small error. Typical beta value is 7 or 8. Beta is ranging from -9 to +9.
411	2d
412	Damping
413	Coefficient to increase the valve response for some applications. A value of 0 gives no Damping. 0 to 250 seconds is for slow down in both directions. -1 to -250 is for slow down in OPEN direction ONLY. -1001 to -1250 is for slow down in CLOSE direction ONLY.
414	Position Comp.
415	The response of the valve is different when the valve is nearly closed than when nearly open. This coefficient allows the user to make adjustments to try to equalize the valve response. Normal value is 6 and this value is ranging from 2 to 20.
416	Dead Zone
417	When the valve position is within the setpoint +/- the dead zone and, no additional position control is performed. This value is normally 0%. Used to avoid limit cycling for high friction valves. Range is 0 to 5%.
418	Boost
419	Boost- Compensates for the pnuematic dead band. Value ranges between 0 and 20.
420	Non Linear
421	Reserved 1
422	Auto Tune Fault
423	Reason for Auto Tune failure
424	Pos Error Band
425	Position Error Band- Value corresponding to the maximun error (in % opening) between the setpoint and the valve position allowed, before setting a status flag regards the selection of associated variable Time. Value must be between 0.5% and 100.0% .
426	Pos Error Enable
427	Enable Position Error- enable position error testing
428	Pos Error Time
429	Position Error Time- time before to set the warning when position error exceeds the configured position error limit. This time must be between 1 s and 328 s.
430	Position Fail
431	Enable Position Fail- enable position fail testing
432	Pos Fail Time
433	Position Fail Time- Time before to put the valve in failsafe mode. This time must be >= 20 s and below 328 s and in any case 2s greater than Time 1 However to inhibit failsave mode set -1 s.
434	Near Closed Value
435	Near Closed Position- Value of valve position below which the user considers the valve as being near closed position. Used in continuous diagnostic calculations. Must be between 0 and 20%.
436	Near Closed Value Check
437	Stop Adjust Flag
438	Low
439	High
440	Low Signal
441	Low Input Signal- Lower range value of input signal for valve closed (direct acting) or lower range value of input signal for valve open (reverse acting). Must be between 3.8 mA and 14 mA.
442	mA
443	High Signal
444	High Input Signal- high input signal for valve open (direct acting) or high input signal for valve open (reverse acting). Must be between 8 mA et 20.2 mA. The difference between Lower Range Value and Upper Range Value (span) must be at least 5 mA.
445	Signal Range Check
446	Select Storage
447	Selects which curve the recently created valve signature is stored to
448	Not Saved
449	Saved
450	Baseline
451	Calibration Sensor
452	Signal
453	Calibration Type
454	Calibration Value
455	The current value of the signal being calibrated.
456	no working pressure
457	Supply Pressure
458	Agressiveness
459	Tune Parameter 1
460	Tune Parameter 2
461	Tune Parameter 3
462	Tune Parameter 4
463	Diag. Test Type
464	Step Response Test
465	Std. Actuator Sig.
466	Speed Level
467	Valve speed motion for recording data. Min is 1 and max is 10.
468	Start Pos
469	End Pos
470	Sample Rate
471	Diag Param 2
472	Diag Param 3
473	Stroke Time Open
474	Fastest time to open the valve on the full stroke. This value is given from the standard diagnostic calculations.
475	Stroke Time Close
476	Fastest time to close the valve on the full stroke. This value is given from the standard diagnostic calculations.
477	Friction
478	Friction- This value comes from the standard diagnostic calculations.
479	Lower Spring Range
480	Low spring value. This value comes from the standard diagnostic calculations.
481	Upper Spring Range
482	High spring value. This value comes from the standard diagnostic calculations.
483	Actual Supply Pressure
484	Option Config 0
485	Pressure Sensor 1
486	Pressure Sensor 2
487	Pressure Supply
488	Input/Output Switches
489	Retransmit Output
490	System Version-Positioner function level.
491	Undefined
492	ES - EZ Smart
493	SD - Standard Diag
494	AD - Advanced Diag
495	DP - Diagnostics Plus
496	ESD
497	Option Config 1
498	Remote Position Sensor
499	Single Acting
500	Process Variable Input
501	Device Type
502	Positioner Type - single acting positioner or double acting positioner.
503	Double Acting
504	Active Position Sensor
505	Position Sensor- built-in or remote position sensor.
506	Hall Sensor
507	Remote Sensor
508	I/P Type
509	I/P Type- defined within Option Config 2
510	Relay Type
511	Relay Type- defined within Option Config 2
512	Option Config X
513	Actuator Press. 1
514	Actuator Port Pressure 1
515	Actuator Press. 2
516	Actuator Port Pressure 2
517	Air Supply Pressure
518	I/P Pressure
519	20mA signal at a travel of
520	Position in % at 20mA for position retransmitter
521	4mA signal at a travel of
522	Position in % at 4mA for position retransmitter
523	X1
524	X defines signal input in % and Y defines position value in % The min and max values are respectively 0.0% and 100.0% The custom curve must have at least one pair. A coordinate (100.0%,100.0%) indicates the end of the curve.
525	Y1
526	X2
527	Y2
528	X3
529	Y3
530	X4
531	Y4
532	X5
533	Y5
534	X6
535	Y6
536	X7
537	Y7
538	X8
539	Y8
540	X9
541	Y9
542	X10
543	Y10
544	Signal A/D
545	Value of Signal A/D
546	2nd Signal A/D
547	Temperature A/D
548	Temperature A/D value
549	Atm Press A/D
550	Atm Pressure AD value
551	Rem Pos A/D
552	Remote Position A/D value
553	Supply Press A/D
554	Supply Pressure A/D value
555	Hall Sensor A/D
556	Hall Sensor A/D value
557	Act Press 1 A/D
558	Acutuator Pressure 1 A/D value
559	Act Press 2 A/D
560	Actuator Pressure 2 A/D value.
561	Pilot Press A/D
562	Pilot Pressure A/D value.
563	I/P Current A/D
564	I/P current A/D value.
565	Ref Voltage A/D
566	Reference voltage A/D value.
567	Signal value after factory temperature correction.
568	the 2nd Signal value after factory temperature correction.
569	Temperature A/D value after factory temperature correction.
570	Atm pressure value after factory temperature correction.
571	Remote Position value after temperature correction
572	Supply pressure value
573	Hall sensor value
574	Actuator pressure 1 value
575	Actuator Pressure 2 value
576	Pilot pressure value
577	I/P current value
578	Reference voltage value
579	SubMode
580	SubMode - SVI II AP out-of-service modes can be: setup, low power, fail safe, or fatal. SubMode is only valid when Mode is Out-Of-Service.
581	This mode allows the user to describe the basic valve setup,to perform calibration and diagnostic.
582	Process Busy
583	Percent Complete
584	Analog Output
585	Analog Output - fixed value to set for position retransmitter. Set to 0 will put the retrasmitter out of the fixed output mode.
586	Unused(int3)
587	Curve Select
588	Current
589	Baselined
590	Signature Data 1
591	Increasing Pressure sampling data 1
592	Signature Data 2
593	Increasing Pressure sampling data 2
594	Signature Data 3
595	Increasing Pressure sampling data 3
596	Signature Data 4
597	Increasing Pressure sampling data 4
598	Signature Data 5
599	Increasing Pressure sampling data 5
600	Signature Data 6
601	Increasing Pressure sampling data 6
602	Signature Data 7
603	Increasing Pressure sampling data 7
604	Signature Data 8
605	Increasing Pressure sampling data 8
606	Signature Data 9
607	Increasing Pressure sampling data 9
608	Signature Data 10
609	Decrease pressure samping data 1
610	Signature Data 11
611	Decrease pressure samping data 2
612	Signature Data 12
613	Decrease pressure samping data 3
614	Signature Data 13
615	Decrease pressure samping data 4
616	Signature Data 14
617	Decrease pressure samping data 5
618	Signature Data 15
619	Decrease pressure samping data 6
620	Signature Data 16
621	Decrease pressure samping data 7
622	Signature Data 17
623	Decrease pressure samping data 8
624	Signature Data 18
625	Decrease pressure samping data 9
626	The lower spring range in standard scaling
627	Upper spring range
628	The upper spring range in standard scaling
629	Speed
630	The speed at which the test was run
631	fPressMin
632	fPressMax
633	10%
634	20%
635	30%
636	40%
637	50%
638	60%
639	70%
640	80%
641	90%
642	Read Custom Characterization Data
643	Select characterization. If Custom is selected then continue to set custom points.
644	Edit Characterization
645	Save
646	Save the signature data.
647	save the current signature data
648	Baselined the saved signature data.
649	Load the current signature curve.
650	Load the saved signature curve.
651	Load the baselined signature curve.
652	Translate Signature Data
653	Load the signature data from device
654	Device Configuration
655	Device Diagnostics
656	characterization
657	Input calibration diagram
658	input calibration
659	SVI2AP Switches
660	SVI2AP Retransmit
661	Sig.
662	Y-Axis: 4.0 - 20.0 mA
663	Y-Axis: 0 - 100%
664	Pos.
665	Press.
666	Axis for pressure
667	Pressure axis (0~150psi)
668	psi
669	Pressure axis(0~850kpa)
670	kpa
671	Pressure axis (0~20bar)
672	bar
673	Input signal 4-20mA
674	Input signal 0-100%
675	Manual SetPoint
676	Act. Press. 1
677	Act. Press.
678	The actuator pressure 1 for double actuator.
679	The actuator pressure for single actuator.
680	Act. Press. 2
681	The actuator pressure 2 for double actuator.
682	Supply Press.
683	Valve Position3
684	Trend
685	STRIP0
686	STRIP1
687	STRIP2
688	STRIP3
689	The chart for valve position and manual set position
690	Position Bar
691	Signal Bar
692	Monitor
693	Read Pressure
694	SVI 2 AP HART
695	Valve Travel Find Stops
696	Valve Travel Tuning
697	Pressure Sensors
698	Diagnostics
699	Tuning
700	Std. Diagnostic Data
701	Pressures Gauges
702	Custom Characterization
703	Input Signal(%)
704	Position Value(%)
705	Charc Curve
706	Characterization Curve. Please use method Custom / Standard Characterization for editing custom characterization.
707	Characterization Curve
708	Graph of Characterization Curve
709	Device Status
710	Clear Faults
711	Device Faults
712	Operation
713	Firmware
714	Circuit
715	Raw data
716	Valve Historian
717	Current Signature
718	Saved Signature
719	Baselined Signature
720	waveform of sample_array
721	Increase Press. per 10%
722	Decrease Press. per 10%
723	Signature Data
724	Up Direction
725	Down Direction
726	History
727	Main signal
728	What is Current Mode?
729	What is Current Mode? - To get the current mode of this device
730	Displays CONTINUOUS DIAGNOSTIC DATA including number of full strokes the valve has made,the number of cycles (direction changes),the time the valve has spent open, the time the valve has been closed and the time the valve has spent throttling near the seat.
731	Read Diagnostic Data
732	Read Raw Data
733	Returns information from the SVI2AP that is useful to Masoneilan technicians for diagnostic purposes. The information includes the input current on the auxiliary input channel, the A/D values from the pressure, signal, and position measurements, the D/A value of the signal to the I/P, and the internal SVI2AP temperature.
734	FMU860
735	DT
736	DVC
737	FCX
738	AS800
739	340T
740	340C
741	344
742	Siemens Micro K
743	SITRANS L
744	SIPAN PH
745	SITRANS P
746	75SMT
747	UNIDELTA
748	8320
749	SX5100
750	TSV175
751	DMU
752	3780
753	BM70
754	8u
755	Firmware Version - %{0}.%{1}.%{2}
756	Set Mode Target
757	Normal;Manual;Setup
758	Positioner is in Bumpless Transfer mode. Change modes to Manual to cancel
759	WARNING. Leaving Normal Mode will result in LOSS of process CONTROL and may cause sudden valve move. DO YOU WISH TO CONTINUE?
760	Procedure aborted Try Again.
761	Perform Find Stops is not allowed when device is in marginal power.
762	WARNING. This procedure requires to enter setup mode and will result in LOSS of PROCESS CONTROL. Do you wish to proceed ?
763	Changing mode to Setup
764	WARNING. This procedure will MOVE the valve. This will result in LOSS of process CONTROL. DO YOU WISH TO CONTINUE?
765	Please wait while searching for mechanical stops. This should take approximately 30 seconds. Press OK to continue.
766	Please Wait ...
767	Press the ABORT key to abort the process.
768	Find stop limits FAILED.
769	Please verify that: - Air supply is sufficient; - The valve is not handjacked; - The mounting is adequate;
770	Please verify that (Continued): - The Travel Sensor is set properly. Then re-run find stops again.
771	Find stop limits completed.
772	Remove software limit stops to be able to perform autotune.
773	Enter an Aggressiveness value (-9 to 9)
774	Enter the Supply pressure
775	Error: Supply pressure is out of range. Enter again!
776	Please wait while searching for optimal valve tuning parameters. This should take approximately 3 to 6 minutes.
777	Auto Tune Failed FAILED.
778	Fail in open loop test.Check if air booster or quick exhaust is used and the pressure supply.
779	P is out of range.
780	Padj is out of range.
781	Error finding Bias.
782	Self-tuning for air fill direction fails. Check supply pressure or pneumatic block.
783	Self-tuning for air exhausting direction failed. Check the pneumatic block.
784	Auto Tune returned unknown error - %{0}.
785	Auto Tune completed.
786	This mode is not appropriate for the Setup Wizard. Click OK to change mode or Abort to exit Setup Wizard.
787	Air Action Configuration:
788	Skip This Task;Select Air Action
789	Select Air Action
790	Apply new changes to the device? Press: OK for YES ABORT for NO
791	Find Valve Stops:
792	Skip This Task;Run Find Stops
793	Find stop limits FAILED!
794	Please verify that: - Air supply is sufficient; - The valve is not handjacked; - The mounting is adequate;
795	Please verify that (Continued): - The Travel Sensor is set properly. Then re-run find stops again.
796	Auto Tune:
797	Skip This Task;Run Auto Tune
798	Auto Tune FAILED.
799	Reset to Factory Default:
800	Skip This Task;Set All Values to Default
801	Are you sure you want to reset all data to factory defaults?
802	Reset to Factory Defaults completed.
803	No faults recorded.
804	Do you want to clear current faults ?
805	No;Yes
806	Device has malfunctioned
807	Faults have been cleared.
808	No Historic Faults.
809	Do you want to clear all faults ?
810	The device must not be in NORMAL mode to perform this operation. Select Change Mode from the Hot Key menu to change the mode.
811	WARNING! This command strokes the valve and should not be performed with process running.
812	Manual Setpoint:
813	Set By Position;Set By Signal
814	Valve Position (-5% ~ 160%):
815	Position Corresponding to Signal in mA:
816	Allow Override Limits
817	Select Tight Shutoff
818	Pressure Units
819	Display Language
820	Button Lock Level
821	Valve Near Closed Value
822	Select Cam
823	Enter/edit cam characterization ?
824	Input your 9 XY pairs of points between (0.0%, 0.0%) and (100.0%,100.0%).
825	X[%{i}]
826	Y[%{i}]
827	Invalid segment: X%{a} = %{0}, X%{i} = %{1} - Same X.
828	Invalid segment: X0=0, X%{i}=%{0} - Slope too low.
829	Invalid segment: X%{a}=%{0}, X%{i}=%{1} - Slope too low.
830	Invalid segment: X0=0, X%{i}=%{0} - Slope too high.
831	Invalid segment: X%{a}=%{0}, X%{i}=%{1} - Slope too high.
832	Invalid segment: X%{a}=%{0}, X%{i}=%{1} - Slope changes too much.
833	Invalid segment: X%{a}=%{0}, X%{i}=%{1} - Slope changes too small.
834	Found bad segment(s). Please make your selection to continue:
835	Enter data again to correct error(s); Abort the method; Proceed to save without correction.
836	The position retransmitter has restored to the normal control mode of following the position.
837	There is no position retrasmitter for this device.
838	Setting analog output is disabled when device is in the %{0} mode
839	Set current output of the position retransmitter:
840	Set Output in mA;Finished
841	Set Output in 4 - 20 mA:
842	Lower Range in %
843	Upper Range in %
844	Error: Lower and upper ranges must differ by at least 5%.
845	Set re-transmitter range is done.
846	Set Manual Stop Position:
847	Low;High;Exit
848	Wait until the valve is stable, then press OK.
849	Procedure failed. The stroke could be too small.
850	Open Stop Adjustment set properly.
851	P = %{0} % I = %{1} (1/10s) D = %{2} ms Padj = %{3} % Beta = %{4}
852	Stroke Time = %{5} Compens. pos.= %{6} Dead zone = %{7} % Boost = %{8}
853	P (%)
854	I (1/10s)
855	D (ms)
856	Padj (%)
857	Compensation
858	Dead Zone (%)
859	Stroke Time Open = %{0} sec Stroke Time Close = %{1} sec
860	Stroke Time Selection:
861	For both directions;For open only;For close only
862	Stroke Time (0 to 250 sec)
863	Set the I/P Value:
864	WARNING. This procedure requires to enter setup mode. Please change to setup mode first.
865	Enter the low signal value between 3.5 and 8.0 mA:
866	The value must be between 3.5 and 8.0 mA
867	Set the input current to %[.2f]{0} mA and press OK
868	The current is not set correctly! Please check and set again.
869	Enter the high signal value between 16.0 and 21.0 mA:
870	The value must be between 16.0 and 21.0 mA
871	The device has no pressure sensor to calibrate.
872	WARNING. Turn off all the air to the valve and wait until air is fullyexhausted! Then press OK to continue.
873	Actuator Pressure: %{1} %{0} Supply Pressure: %{2} %{0}
874	Actuator Pressure: %{1} %{0}
875	Caution: Make sure if air is fully exhausted or not:
876	Not exhausted yet;Fully exhausted
877	Calibration failed. A pressure sensor may not be in proper range (-3 psi to +3 psi).
878	Calibration is completed.
879	Please turn on the actuator pressure sensor first!
880	Actuator Press. 1: %[.2f]{1} %{0} Actuator Press. 2: %[.2f]{4} %{0} Supply Press: %[.2f]{2} %{0} I/P Press: %[.2f]{3} %{0}
881	Actuator Press.: %[.2f]{1} %{0} Supply Pressure: %[.2f]{2} %{0} I/P Pressure: %[.2f]{3} %{0}
882	Actuator Press. 1: %[.2f]{1} %{0} Actuator Press. 2: %[.2f]{2} %{0}
883	Actuator Press: %[.2f]{1} %{0}
884	WARNING. To continue this procedure will reset calibration data to factory defaults. DO YOU WISH TO CONTINUE?
885	Calibraton data have been reset to factory defaults.
886	Remove software limit stops to be able to perform diagnostics.
887	Select Diagnostic Type:
888	Time (1-60 sec)
889	Start Position in %
890	End Position in %
891	Speed Level (1-10)
892	Please Wait while running a diagnostic signature
893	Diagnostics FAILED.
894	Diagnostics completed.
895	Stroking Time To Open = %{0} s Stroking Time To Close = %{1} s Friction = %{2} %{6}
896	Lower Spring Range = %{3} %{6} Upper Spring Range = %{4} %{6} Supply Pressure = %{5} %{6}
897	Lower Spring Range = %{3} %{6} Upper Spring Range = %{4} %{6}
898	Select Storage for Valve Signature
899	Valve Signature stored.
900	Stroking Time To Open = %{0} s Stroking Time To Close = %{1} s
901	After resetting, the current values will be lost. Press ABORT if you do not wish to proceed.
902	Valve Historian data was reset.
903	A reset may cause the valve to move ! Perform a RESET?
904	Reset on SVI II AP did NOT correctly execute.
905	Reset on SVI II AP correctly executed.
906	Interrupting the current process.
907	The process was interrupted.
908	Value out of range. Tight Shutoff Value MUST be between -1.0 and 20.0.
909	Limit High (%{0} %) must be at least 10% larger than Limit Low (%{1} %) Please enter the value again!
910	Value out of range. Tight Shutoff Value MUST be between 1 and 255.
911	Value out of range. Near Closed Value MUST be between 0.0 and 20.0.
912	High Signal (%{0} mA) must be at least 5mA larger than Low Signal (%{1} mA) Please enter the value again!
913	Found bad segment(s). Please make your selection to continue:Select YES to input again, or NO to Abort.
914	To refresh the signature, Please reload this page!
915	Device is currently in NORMAL mode.
916	Device is currently in MANUAL mode.
917	Device is currently in SETUP mode.
918	Device is currently in LOW POWER mode.
919	Device is currently in FAILSAFE mode.
920	Device is currently in FATAL mode.
921	Device is currently in MARGINALPOWER mode.
922	Device is currently in OOS mode.
923	Device Mode Unknown.
924	This function is not available in this SVI2 model. Consult Masoneilan for more information.
925	Make your choice:
926	Continuous Data;Std Diag. Results
927	Total Travel = %{0} strokes Time Closed = %{1} hours Time Open = %{2} hours Time Near Closed = %{3} hours Number of Cycles = %{4}
928	Following values are not meaningful if the standard diagnostic has not been run.
929	Response Time to Open = %{0} s Response Time to Close = %{1} s Friction = %{2} %{6} Low Spring Range = %{3} %{6} Upper Spring Range = %{4} %{6} Air Supply pressure = %{5} %{6}
930	Response Time to Open = %{0} s Response Time to Close = %{1} s
931	Raw data from the device: (Click Next to Update or Cancel to Exit) Raw Sig = %{0} cts Raw Pos = %{1} cts IP Output = %{2} cts IP Current = %{9} mA Raw Pressure = %{8} cts Low Position Stop = %{3} cts High Positon Stop = %{4} cts Low Temperature = %{5}degC High Temperature = %{6}degC Current Board Temp. = %{7}degC
Reference ID	String