Device dictionary

Loading…

Reference ID	String
0	FLOWSERVE
1	Logix420
2	Mode Status 0
3	Factory Reset State
4	Indicates the unit has had a factory reset and has not yet been calibrated. The unit will not respond to commands and will remain in the failsafe position until a calibration is successfully completed. Proper operation will require stroke, actuator, and friction calibration to be completed. This indicator can be disabled.
5	Calibration in Progress
6	Indicates the device is being calibrated.
7	Signature in Progress
8	Indicates a signature or PST is in progress.
9	Jog Command Mode
10	Indicates the unit has been placed in a local override mode where the valve can only be stroked using the two local jog buttons. Control the valve using the jog buttons. This mode may be canceled by briefly pushing the quick-cal button.
11	Reserved
12	TBD
13	Feedback Loop Status 1
14	Psn Deviation ALM
15	The device is not controlling at the set point.
16	Psn Sensor Fail ALM
17	The feedback arm may be disconnected from the valve assembly.
18	Opened Too Far WRN
19	The valve has opened farther than it did at the last calibration.
20	Closed Too Far WRN
21	The valve has closed farther than it did at the last calibration.
22	PST Failed WRN
23	The last partial stroke test failed.
24	Position Status 2
25	Psn High Limit Alert
26	The Position High Limit has been reached. The command and valve position are above the limit.
27	Psn Low Limit Alert
28	The Position Low Limit has been reached. The command and valve position are below the limit.
29	Feedback Linkage Alarm
30	The feedback linkage is broken or the position feedback POT is out of range.
31	Cycles_Travel Status 3
32	Valve Cycles WRN
33	The number of valve cycles is above the warning limit set by the user.
34	Valve Travel WRN
35	The amount of valve travel is above the warning limit set by the user.
36	Pilot Cycles WRN
37	The number of pilot relay cycles is above the warning limit.
38	Pilot Travel WRN
39	The amount of pilot relay travel is above the warning limit.
40	Aux Mode Bits 4
41	Actuation Status 5
42	Supply Press Low ALM
43	The supply pressure is below the low alarm limit.
44	Friction 14
45	Control 15
46	Inner Loop 16
47	Pilot Response WRN
48	The pilot relay response time is above the warning limit.
49	Pilot Response ALM
50	The pilot relay response time is above the alarm limit or the pilot relay is stuck open.
51	Piezo Volts High WRN
52	The voltage driving the piezo is above the warning limit.
53	Piezo Volts High ALM
54	The voltage driving the piezo is above the alarm limit.
55	Piezo Volts Low WRN
56	The voltage driving the piezo is below the warning limit. The valve may not fail safe on loss of power.
57	Piezo Volts Low ALM
58	The voltage driving the piezo is below the alarm limit. The valve may not fail safe on loss of power.
59	Driver Module ALM
60	The pilot relay can't open, the pilot relay can't shut, or the Hall sensor circuit has failed.
61	Main Board 17
62	Main Board Fail WRN
63	There has been an oscillator fault, position sensor ADC failure, supply voltage error, reference voltage error, shunt voltage error, or piezo voltage error.
64	Software Error WRN
65	There has been a watch dog time out, stack overflow warning, or CPU usage warning.
66	Memory Error WRN
67	CPU/FRAM has a memory problem.
68	Not Applicable
69	Temp High WRN
70	The temperature in the positioner is above the high limit.
71	Temp Low WRN
72	The temperature in the positioner is below the low limit.
73	Aux Boards 18
74	spare 1 19
75	spare 2 20
76	spare 3 21
77	CMD 48: Read additional device status
78	cmd LS
79	cmd PDQ
80	Command Perc
81
82	%
83	cmd Fmly stat
84	Command Units
85	FB Class
86	FB LS
87	FB PDQ
88	FB Fmly stat
89	Position damping value
90	5.2f
91	Lower position limit
92	5.1f
93	Position minimum span
94	.1f
95	Position upper limit
96	Position
97	SP Class
98	Final command
99	Tertiary units
100	Temperature
101	UD1 Class
102	UD1 LS
103	UD1 PDQ
104	UD1 Fmly stat
105	UD2 Class
106	UD2 LS
107	UD2 PDQ
108	UD2 Fmly stat
109	Analog Command Units
110	FeedBack USL
111	FeedBack LSL
112	FeedBack min span
113	FeedBack damping value
114	FeedBack snr
115	Digital Command
116	Digital Command Value
117	Digital Command Units
118	Digital Command PDQ
119	Digital Command LS
120	Digital Command Fmly stat
121	Digital Command Classification
122	CmdPctDigital USL
123	CmdPctDigital LSL
124	CmdPctDigital min span
125	CmdPctDigital damping value
126	CmdPctDigital snr
127	Control Signal
128	Control Signal Value
129	Control Signal Units
130	Control Signal PDQ
131	Control Signal LS
132	Control Signal Fmly stat
133	Control Signal Classification
134	CmdPct USL
135	CmdPct LSL
136	CmdPct min span
137	CmdPct damping value
138	CmdPct snr
139	Command Input Target
140	Command Input Target Value
141	Command Input Target Units
142	Command Input Target PDQ
143	Command Input Target LS
144	Command Input Target Fmly stat
145	Command Input Target Classification
146	CmdPctTarget USL
147	CmdPctTarget LSL
148	CmdPctTarget min span
149	CmdPctTarget damping value
150	CmdPctTarget snr
151	Valve Stem Position
152	Position Units
153	Position PDQ
154	Position LS
155	Position Fmly stat
156	Position Classification
157	PsnPct USL
158	PsnPct LSL
159	PsnPct min span
160	PsnPct damping value
161	PsnPct snr
162	Deviation
163	Deviation Value
164	Deviation Units
165	Deviation PDQ
166	Deviation LS
167	Deviation Fmly stat
168	Deviation Classification
169	DevPct USL
170	DevPct LSL
171	DevPct min span
172	DevPct damping value
173	DevPct snr
174	Pilot Relay Command
175	Pilot Relay Command Value
176	Pilot Relay Command Units
177	Pilot Relay Command PDQ
178	Pilot Relay Command LS
179	Pilot Relay Command Fmly stat
180	Pilot Relay Command Classification
181	PilotCmdPct USL
182	PilotCmdPct LSL
183	PilotCmdPct min span
184	PilotCmdPct damping value
185	PilotCmdPct snr
186	Pilot Relay Position
187	Pilot Relay Position Value
188	Pilot Relay Position Units
189	Pilot Relay Position PDQ
190	Pilot Relay Position LS
191	Pilot Relay Position Fmly stat
192	Pilot Relay Position Classification
193	PilotPsnPct USL
194	PilotPsnPct LSL
195	PilotPsnPct min span
196	PilotPsnPct damping value
197	PilotPsnPct snr
198	Temperature Value
199	Temperature Units
200	Temperature PDQ
201	Temperature LS
202	Temperature Fmly stat
203	Temperature Classification
204	Temperature USL
205	Temperature LSL
206	Temperature min span
207	Temperature damping value
208	Temperature snr
209	Pilot Response Time
210	Pilot Response Time Value
211	Pilot Response Time Units
212	Pilot Response Time PDQ
213	Pilot Response Time LS
214	Pilot Response Time Fmly stat
215	Pilot Response Time Classification
216	PilotResponseTime USL
217	PilotResponseTime LSL
218	PilotResponseTime min span
219	PilotResponseTime damping value
220	PilotResponseTime snr
221	4-20 Command (mA)
222	4-20 Command (%)
223	Digital Command (%)
224	Control Signal (%)
225	Command Input, Actual Target, %
226	Position (%)
227	Deviation (%)
228	Pilot Relay Command (%)
229	Pilot Relay Position (%)
230	Ambient Temperature
231	Pilot Relay Response Time
232	Actuation Status Mask
233	Bit3=Supply Press Lo ALM
234	Supply Press Lo ALM
235	Mask or disable this alarm or warning
236	Actuation Status
237	Actuator Size
238	Actuator Size / area
239	Displays and allows selection of actuator manufacturer.
240	Manufacturer
241	Valtek (Piston)
242	Kammer
243	Valtek (Diaphragm Rotary)
244	Automax
245	NAF
246	Valtek (Diaphragm Linear)
247	Fisher
248	Worcester/Norbro
249	Other
250	Not Configured
251	Displays Actuator Model
252	Actuator Model
253	25
254	50
255	100
256	100C
257	150C
258	200
259	200C
260	300
261	400
262	500
263	600
264	37
265	38
266	39
267	3D
268	47
269	48
270	49
271	4D
272	P0
273	P1
274	P2
275	P3
276	P4
277	P5
278	P6
279	P7
280	NR1
281	NR2
282	NR3
283	B050D
284	B063D
285	B085D
286	B100D
287	B115D
288	B125D
289	B150D
290	B175D
291	B200D
292	SNA250
293	SNA300
294	R205
295	R206
296	R207
297	R208
298	R310
299	R312
300	R314
301	R316
302	R414
303	R416
304	R418
305	R420
306	R422
307	R514
308	R516
309	R518
310	R520
311	R522
312	R524
313	02
314	11
315	12
316	21
317	22
318	31
319	32
320	41
321	42
322	51
323	52
324	127
325	252
326	502
327	700
328	1502
329	3002
330	657-30
331	657-34
332	657-40
333	657-45
334	657-46
335	657-50
336	657-60
337	657-70
338	657-80
339	657-87
340	657-100
341	667-30
342	667-34
343	667-40
344	667-45
345	667-46
346	667-50
347	667-60
348	667-70
349	667-80
350	667-87
351	667-100
352	RG106
353	RG107
354	RG108
355	RG109
356	RG110
357	RG112
358	RG208
359	RG209
360	RG210
361	RG212
362	RG214
363	RG216
364	RG310
365	RG312
366	RG314
367	RG316
368	RG318
369	RG320
370	RG414
371	RG416
372	RG418
373	RG420
374	RG422
375	RG424
376	RG516
377	RG518
378	RG520
379	RG522
380	RG524
381	RG528
382	RG618
383	RG620
384	RG622
385	RG624
386	RG628
387	RG632
388	RG636
389	RG724
390	RG728
391	RG732
392	RG736
393	RG740
394	RG828
395	RG832
396	RG832T
397	RG836
398	RG836T
399	RG840
400	05
401	10
402	15
403	20
404	30
405	33
406	35
407	40
408	45
409	Spring type i.e. single or heavy duty etc.
410	Actuator Spring
411	Single
412	Heavy duty
413	Dual
414	Multi
415	None
416	Standard
417	1
418	2
419	3
420	4
421	5
422	6
423	7
424	8
425	9
426	Actuator type i.e. linear or rotary; piston or diaphragm etc.
427	Actuator Style
428	Linear (piston)
429	Linear (diaphragm)
430	Rotary (piston)
431	Rotary (diaphragm)
432	Rotary (rach & pinion)
433	Displays the ID of Aux card 1
434	Aux Card 1 ID
435	No Card
436	MFC
437	Safety DO
438	Displays the ID of Aux card 2
439	Aux Card 2 ID
440	Displays the Type of aux Card 1
441	Aux Card 1 Type
442	Analog Output
443	Discrete Output
444	Discrete Input
445	Displays the Type of aux Card 2
446	Aux Card 2 Type
447	Command calibration bits
448	Cal Cmd Config
449	Set Command to OOS
450	Set 4mA Position
451	Set 0% Position
452	Set 100% Position
453	Cal Get Date Pntr
454	Used in command 185 and 186 as a pointer to which cal date to read.
455	Stroke Calibration
456	Pressure Calibration
457	Friction Calibration
458	Triple Calibration
459	Command Input Calibration
460	Analog Output Calibration
461	Cal Put Date Pntr
462	Used in command 185 and 186 as a pointer to which cal date to write.
463	Cal Date/Time
464	The that the last calibration took place.
465	Who Ran Calibration
466	Initials of who ran the last calibration.
467	Displays and sets the calibration state.
468	Calibration State
469	None / Abort
470	Displays the position Characterization options (linear, equal %, custom, etc....)
471	Other Characterization
472	MaxFlo Linear
473	MaxFlo Percent
474	Valdisk Linear
475	Valdisk Percent
476	ShearStream Linear
477	ShearStream Percent
478	Custom
479	Input 4-20mA command expressed in percent of full scale input.
480	4-20 Cmd
481	Enter the digital command value, in percent of full stroke. This variable is available only when the valve is being positioned by a digital command (digital source) rather than the 4-20mA analog signal (analog source).
482	Digital Cmd
483	The modified command signal, in percent of full stroke, which actually sets the controlled position of the valve. Cntrl Cmd is generated after custom characterization, soft limits, and minimum position cutoff parameters are evaluated. 4-20 mA command and Cntrl Cmd can differ if custom characterization, soft limits, or minimum position cutoff are active.
484	Cntrl Cmd
485	Control Input Source
486	Contains the source of the control parameters of the input controlling signal or data.
487	Digital Command Source
488	Out Of Service
489	Inner Loop Command Mode
490	Valve Stability Enabled
491	P-GAIN Enabled
492	I-GAIN Enabled
493	D-GAIN Enabled
494	Date Day
495	Current Day
496	Time_Hourss
497	Current time, hour parameter.
498	Time_Minutes
499	Current time, minutes parameter.
500	Date Month
501	Current Month
502	January
503	February
504	March
505	April
506	May
507	June
508	July
509	August
510	September
511	October
512	November
513	December
514	Time_Seconds
515	Current time, seconds parameter.
516	Date Year
517	Current Year.
518	Cycles/Travel Mask
519	Bit1=Valve Cycles WRN, Bit2=Valve Travel WRN, Bit7=Pilot Cycles WRN, Bit8=Pilot Travel WRN
520	Cycles/Travel Status
521	Displays the orientation of the positioner and LCD
522	LCD Orientation
523	Reversed
524	Normal
525	Displays the type of pilot relay positioner has
526	Pilot Relay Type
527	Spool
528	Poppet
529	DGain Basic Close
530	D Gain Basic Close.
531	DGain Basic Open
532	D Gain Basic Open.
533	Displays the position of the air action dip switch
534	Dip Sw Air Action
535	ATC
536	ATO
537	Displays the position of the auto tune dip switch
538	Dip Sw AutoTune
539	Off
540	On
541	Displays the position of the characterization dip switch
542	Dip Sw Characterization
543	Linear
544	Displays the position of the pilot action dip switch
545	Dip Sw Actuator
546	Single Acting
547	Double Acting
548	Displays the position of the quick cal dip switch
549	Dip Sw QuickCal
550	Jog
551	Auto
552	Displays the position of the Signal to close dip switch
553	Dip Sw Sig Closed
554	20 mA
555	4 mA
556	Displays the position of the spare dip switch
557	Dip Sw Spare
558	B
559	A
560	Displays the position of the valve stability dip switch
561	Dip Sw Stability
562	High Friction
563	Low Friction
564	DTerm Depth Close
565	D Term Depth Close.
566	DTerm Depth Open
567	D Term Depth Open.
568	Elec Comp Status Mask
569	Bit1=Pilot Can not Open, Bit2=Pilot Can not Shut, Bit3=Hall Sensor Fail, Bit4=ILO Out of Range
570	Pilot Can not Open
571	Pilot Can not Shut
572	Hall Sensor Fail
573	ILO Out of Range
574	Elec Comp Status
575	The pilot relay is stuck and will not move into the open position.
576	The pilot relay is stuck and will not move into the closed position.
577	The hall sensor has failed or is disconnected.
578	ILO is not close to expected value.
579	Elec Config Status Mask
580	Bit4=LCD Present
581	LCD Present
582	Elec Config Status
583	An LCD display is present.
584	Serial Number of the electronics control board.
585	Electronic S/N
586	Embedded software release.
587	Software Release
588	ESR Major
589	Embedded code major version number.
590	ESR Minor
591	Embedded code minor version number.
592	Day/Year
593	EventHistoryReadIndex
594	EventHistoryReadIndex.
595	Event State
596	Event ON or OFF.
597	False
598	True
599	Event Status
600	Event indicator parameter.
601	Power ON
602	Initializing
603	Stroke Calibration Required
604	Pressure Calibration Required
605	Friction Calibration Required
606	Digital Command Mode
607	Tight Shutoff Mode
608	Valve Stability Locked
609	Soft Stop High Limit Alert
610	Soft Stop Low Limit Alert
611	Continuous Stroke Test Mode
612	Training Mode in Progress
613	Training Mode Completed
614	Event Captured
615	Local Interface Off
616	Squawk Mode
617	Stroke Calibration in Progress
618	Setting Inner Loop Offset
619	Pressure Calibration in Progress
620	Friction Calibration in Progress
621	Command Input Calibration in Progress
622	Analog Output Calibration in Progress
623	Jog Calibration Set 100% Position
624	Position Range Too Small
625	Position Sensor Below ADC Range
626	Position Sensor Above ADC Range
627	No Motion Time Out
628	Settle Time Out
629	Inner Loop Offset Time Out
630	Analog Output Range Too Small
631	Command Input Range Too Small
632	Command Input Below ADC Range
633	Command Input Above ADC Range
634	Stroke Shift
635	Stroke Span Increase
636	Stroke Span Decrease
637	Aux Card 1 Present
638	Aux Card 2 Present
639	Pressure Sensor Board Present
640	Signature or Partial Stroke Test in Progress
641	Partial Stroke Test Scheduled
642	DI Command Override
643	Position Deviation Alarm
644	Position sensor Failure Alarm
645	Valve Opened Too Far Warning
646	Valve Closed Too Far Warning
647	Backlash Warning
648	Backlach Alarm
649	Partial Stroke Test Failed Warning
650	Continuous Stroke Test Failed Warning
651	Position High Limit Alert
652	Position Low Limit Alert
653	Valve Cycles Warning
654	Valve Travel Warning
655	Actuator Cycles Warning
656	Actuator Travel Warning
657	Bellows Cycles Warning
658	Bellows Travel Warning
659	Pilot Relay Cycles Warning
660	Pilot Relay Travel Warning
661	Fail Safe Mode
662	Pressure Correction Mode
663	Pressure Feedback Mode
664	Open Feedback Loop Mode
665	Open Inner Loop Mode
666	Supply Pressure High Warning
667	Supply Pressure Low Warning
668	Supply Pressure Low Alarm
669	Actuation Ratio Warning
670	Spring Unable to Fail Safe Warning
671	Pneumatic Leak Warning
672	Air Supply Humid Warning
673	Air Supply Icing Warning
674	Friction High Warning
675	Friction High Alarm
676	Friction Low Warning
677	Friction Low Alarm
678	Stiction Warning
679	Stiction Alarm
680	Valve Can Not Open Alarm
681	Valve Can Not Close Alarm
682	Command Frequency Warning
683	Commnad Frequency Alarm
684	Command Amplitude Warning
685	Command Amplitude Alarm
686	Position Frequency Warning
687	Position Frequency Alarm
688	Position Amplitude Warning
689	Position Amplitude Alarm
690	Pilot Relay Response Warning
691	Pilot Relay Response Alarm
692	Piezo Voltage High Warning
693	Piezo Voltage High Alarm
694	Piezo Voltage Low Warning
695	Piezo Voltage Low Alarm
696	Driver Module Alarm
697	Main Board Electronic Failure Warning
698	Software Error Warning
699	Memory Error Warning
700	Loss of Inter-PCB comm Alarm
701	Temp High Warning
702	Temp Low Warning
703	Aux Card 1 Failure Warning
704	Aux Card 2 Failure Warning
705	Aux Card 1 No Loop Power
706	Aux Card 2 No Loop Power
707	Aux Card 1 Error
708	Aux Card 2 Error
709	Pressure sensor Board Failure Warning
710	Low Battery Warning
711	Reversed Spring
712	Insufficient Spring
713	No Spring
714	Oscillator Fault
715	Position Sensor ADC Failure
716	Supply Voltage Error
717	Reference Voltage Error
718	Shunt Voltage Error
719	Piezo Voltage Error
720	Pilot Can Not Open
721	Pilot Can Not Shut
722	Hall Sensor Failure
723	NVMEM CRC Error
724	RAM Error
725	RAM CRC Error
726	FLASH CRC Error
727	Watch Dog Time Out
728	Stack Overflow Warning
729	CPU Usage Warning
730	Firmware Update Applied
731	Port S Out of Range
732	Port A Out of Range
733	Port B Out of Range
734	Port S Range Too Small
735	Port A Range Too Small
736	Port B Range Too Small
737	Pressure Sensor Failure
738	Event 1.
739	Event 2.
740	Event 3.
741	Event 4.
742	Event 5.
743	Event 6.
744	Event 7.
745	Event 8.
746	Event 9.
747	Event 10.
748	Event 11.
749	Event 12.
750	Event 13.
751	Event 14.
752	Event 15.
753	Event 16.
754	Event 17.
755	Event 18.
756	Event 19.
757	Event 20.
758	Event 21.
759	Event 22.
760	Event 23.
761	Event 24.
762	Event 25.
763	Event 26.
764	Event 27.
765	Event 28.
766	Event 29.
767	Event 30.
768	Event 31.
769	Event 32.
770	Time
771	EventTimelineConfig
772	EventTimelineConfig.
773	Event Day
774	Event_Hours
775	Event time, hour parameter.
776	Event Minutes
777	Event time, minutes parameter.
778	Event Month
779	Event Seconds
780	Event time, seconds parameter.
781	Event Year
782	Event Year.
783	FeedBack Loop Status Mask
784	Bit1=Psn Deviation ALM, Bit2=Psn Sensor Fail ALM, Bit3=Opened Too Far WRN, Bit4=Closed Too Far WRN, Bit7=PST Failed WRN
785	FeedBack Loop Status
786	Friction in user units.
787	Friction
788	Valve Stability Mask
789	Bit7=Valve Can Not Open ALM, Bit8=Valve Can Not Shut ALM
790	Valve Can Not Open ALM
791	Valve Can Not Shut ALM
792	Valve Stability Status
793	Pressure has been applied, but the valve is not opening.
794	Pressure has been applied, but the valve is not closing.
795	SAVED FOR FUTURE USE
796	FUTURE USE
797	Integer register Number.
798	Register Number
799	Integer Register Value
800	Int Value
801	HART Dev Type
802	HART Device Type Number.
803	HART Manufacturer ID
804	Hart Manufactuer ID number.
805	Lifetime Hours
806	Number of hours positioner has run for its lifetime.
807	Power Up Hours
808	Number of hours positioner has since last power cycle.
809	Reset Hours
810	Number of hours positioner has run since last reset.
811	IGain Close
812	I Gain Close.
813	IGain Open
814	I Gain Open.
815	Inner Loop Status Mask
816	Bit1=Pilot Response WRN, Bit2=Pilot Response ALM, Bit3=Piezo Volts High WRN, Bit4=Piezo Volts High ALM, Bit5=Piezo Volts Low WRN, Bit6=Piezo Volts Low ALM, Bit7=Driver Module ALM
817	Inner Loop Status
818	Inner Loop Offset
819	Diagnostics Level
820	Indicates whether positioner is Standard, Advanced or Professional.
821	Pressure sensors are used for control only.
822	Advanced
823	Pressure values and alarms are available.
824	Pro
825	Full diagostic features are available including friction and partial stroke testing.
826	Tamper Lock
827	Indicates whether the local pannel of the device has been enabled or disabled.
828	Disabled
829	Enabled
830	Pin Code
831	Pin code to disable local interface.
832	Main Board Detail Status Mask
833	Bit2=Oscillator Fault, Bit3=Psn Sensor ADC Fail, Bit4=Supply Voltage Error, Bit5=Ref Voltage Error, Bit6=Shunt Voltage Error, Bit7=Piezo Voltage Error
834	Psn Sensor ADC Fail
835	Ref Voltage Error
836	Main Board Detail Status
837	The CPU clock had an error.
838	The feedback POT analog-to-digital converter failed.
839	The supply voltage is out of range.
840	The reference voltage is out of range.
841	The terminal (compliance) voltage is out of range.
842	The piezo driver voltage is incorrect.
843	Main Board Status Mask
844	Bit1=Main Board Fail WRN, Bit2=Software Error WRN, Bit3=Memory Error WRN, Bit4=Not Applicable, Bit5=Temperature High WRN, Bit6=BTemperature Low WRN
845	Main Board Status
846	Min Close Time
847	Min Close Time.
848	sec.
849	Min Open Time
850	Min Open Time.
851	Mode Status Mask 1
852	Bit1=Dig Cmd Mode, Bit2=Tight Shut Off mode, Bit3=Valve Stability Lock, Bit4=Soft Stop High Alert, Bit5=Soft Stop Low Alert
853	Digital Cmd Mode
854	Tight Shut Off Mode
855	Valve Stability Lock
856	Soft Stop High Alert
857	Soft Stop Low Alert
858	Mode States Status Mask
859	Bit1=Factory Reset State, Bit2=Calibration in Prog, Bit3=Signature or PST, Bit4=Jog Cmd Mode
860	Calibration in Prog
861	Signature or PST
862	Jog Cmd Mode
863	Mode Status 1
864	The device is in digital command mode.
865	One side of the actuator has full supply pressure while the other is fully vented to ensure a tight shut-off.
866	The positioner is actively using pressure readings to keep the valve steady.
867	The Soft Stop High Limit has been reached. The command is above the limit. The positioner is holding the valve position at the limit.
868	The Soft Stop Low Limit has been reached. The command is below the limit. The positioner is holding the valve position at the limit.
869	Mode States Status
870	The positioner is in factory reset state. Calibration is required to enable control.
871	A calibration is in progress.
872	A partial stroke test, ramp test, step test, or inner loop signature is in progress.
873	The device is responding to manual input using the jog buttons.
874	Pilot Cyc Full Warning
875	Pilot valve Cycles high end limit.
876	Cycles
877	Pilot Cyc Hi % Warning
878	Pilot valve Cycles high percent Warning.
879	Pilot Cyc Initial Warning
880	Pilot valve Cycles high start limit.
881	PGain Max Close
882	P Gain at Max Close.
883	PGain Max Open
884	P Gain at Max Open.
885	PGain Mult Close
886	P Gain Multiplier Close.
887	PGain Mult Open
888	P Gain Multiplier Open.
889	Pilot Cycles
890	Pilot valve Cycles.
891	Pilot Cycle Rate
892	Pilot valve Cycles center rate monitor.
893	Pilot Resp Time
894	Pilot Travel
895	Pilot valve travel.
896	x100%
897	Pilot Trav Cntr Rate Mon
898	Pilot valve travel center rate monitor.
899	cycles/day
900	The difference between the modified position command (Cntrl Cmd) signal and the stem position signal expressed in percent of full stroke. Deviation = Position - Cntrl Cmd.
901	Pos Deviation
902	Displays positioner model number
903	Model Number
904	Logix 505MD+
905	Logix 510MD+
906	Logix 520MD+
907	Logix 3100MD+
908	Logix 3200MD+
909	Logix 420
910	Actual stem position in percent of full stroke, as measured by the position stem position transducer.
911	Tight Shutoff Active
912	Is position Tight Shutoff Mode active.
913	Position Status Mask
914	Bit1=Psn High Limit Alert, Bit2=Psn Low Limit Alert, Bit3=Feedback Linkage Alarm
915	Position Status
916	Window Gain
917	Gain of the Valve Stability window.
918	Pressure Lock
919	Indicates that the current position is within the Valve Stability Window.
920	No
921	Yes
922	Window Mult
923	Multiplier of the Valve Stability window.
924	Window
925	Size of the Valve Stability window.
926	Pilot Resp Alarm
927	Pilot Response high end limit
928	Pilot Resp % Warning
929	Pilot Response High Percent Warning
930	Pilot Resp Warning
931	Pilot Response high start limit
932	Priority Alarm
933	The position deviation deadband.
934	Posn Dev Deadband
935	The position deviation time.
936	Posn Dev Time
937	The high position that the alert is turned on.
938	Position High Setpoint
939	The low position that the alert is turned on.
940	Position Low Setpoint
941	Force at Breakaway
942	Pressure measured at movement.
943	6.2f
944	PST Result
945	Gives a pass/fail indication of the test based on the reference time to target and the actual time to target.
946	Fail
947	Pass
948	Not Run
949	In Progress
950	Aborted by User
951	Aborted On Cmd
952	PST Time Limit
953	Actual time it took for the valve to arrive within 2% of the final value.
954	PST Net Breakaway Time
955	Measured when the valve has moved ½ % from the starting position
956	PST Time To Target
957	Set bit on to reset the pilot travel and pilot cycle counters
958	Pilot Trav/Cyc Reset
959	Reset Pilot Travel
960	Reset Pilot Cycles
961	Pilot Trav Full Warning
962	Pilot valve travel high end limit.
963	Pilot Trav Hi % Warning
964	Pilot valve travel high percent Warning.
965	Pilot Trav Initial Warning
966	Pilot valve travel high start limit.
967	The Piezo command 1 average.
968	Piezo Cmd1 Avg
969	Volts
970	The Piezo command 2 average.
971	Piezo Cmd2 Avg
972	Piezo High Alarm
973	Piezo High Warning
974	Piezo Low Alarm
975	Piezo Low Warning
976	The Piezo voltage.
977	Piezo volts
978	The Piezo voltage 1 average.
979	Piezo volt1 Avg
980	The Piezo voltage 2 average.
981	Piezo volt2 Avg
982	The Piezo voltage high percent yellow.
983	Pz High Pct Warning
984	The Piezo voltage low percent Warning.
985	Pz Low % Warning
986	The gain position of the rotary switch user interface.
987	Rotary Sw
988	C
989	D
990	E
991	F
992	G
993	H
994	I
995	J
996	Sig Config
997	Signature configuration
998	Start Signature
999	End Signature
1000	Init Bi-directional Signature
1001	Init Ramp Signature
1002	Signature Started
1003	Signals Last Data Frame
1004	Init Pilot Relay Signature
1005	Init PST
1006	Signature Day
1007	Pst Force at Breakaway
1008	The Signature hold time.
1009	Sig Hold Time
1010	Signature time, hour parameter.
1011	Signature time, minutes parameter.
1012	Signature Month
1013	Sig Num
1014	Signature Number type
1015	Step Baseline
1016	Ramp Baseline 1
1017	Ramp Baseline 2
1018	PST Baseline
1019	PST Current
1020	Current 1
1021	Current 2
1022	The time it takes the signature to run the ramp.
1023	Sig Ramp Time
1024	Sig Result
1025	Signature time, seconds parameter.
1026	The Signature starting position.
1027	Sig Start Pos
1028	The Signature stopping position.
1029	Sig StOP Pos
1030	Sig Time Limit
1031	Sig Time To Breakaway
1032	Sig Time To Target
1033	Signature Year.
1034	Software Status Mask
1035	Bit1=NVMEM CRC Error, Bit2=RAM Error, Bit3=RAM CRC Error, Bit4=Flash CRC Error, Bit5=Watch Dog Time Out, Bit6=Stack Overflow WRN, Bit7=CPU Usage WRN, Bit8=Firmware Update
1036	Flash CRC Error
1037	Stack Overflow WRN
1038	CPU Usage WRN
1039	Firmware Update
1040	Software Status
1041	The NVMEM CRC is incorrect.
1042	The RAM location is bad.
1043	The RAM data memory is corrupt.
1044	The FLASH program memory is corrupt.
1045	The flow monitor detected a problem.
1046	The stack is about to overflow.
1047	The CPU usage is too high.
1048	The embedded code on the controller board has been upgraded.
1049	The position high end softstop.
1050	Soft Stop High
1051	The position low end softstop.
1052	Soft Stop Low
1053	Displays if a pressure board is present or not
1054	Press Board Status
1055	Absent
1056	Present
1057	Displays if an LCD is present or not
1058	LCD Avail Status
1059	StartUp Status Mask
1060	Bit1=Power On, Bit2=Initializing, Bit3=Stroke cal Req
1061	Power On
1062	Stroke Cal Req
1063	StartUp Status
1064	Main board has been powered on.
1065	Main board is initializing.
1066	A stroke calibration is required for proper positioning.
1067	Mode Status 2
1068	Bit enumerated Bit1=CST Mode, Bit2=Training in Progress, Bit3=Training Complete, Bit4=Event Captured, Bit5=Local Interface Off, Bit6=Squawk Mode
1069	Cal Status
1070	Bit1=Stroke Cal In Prog, Bit2=Setting ILO, Bit5=Cmd In Cal In Prog, Bit7=Jog Cal set 100%
1071	Stroke Cal In Prog
1072	The positioner is currently performing a stroke calibration.
1073	Setting ILO
1074	The positioner is currently finding the inner control loop offset.
1075	Cmd In Cal In Prog
1076	A calibration of the command signal (analog input) is in progress.
1077	Jog Cal Set 100% Pos
1078	Waiting for the user to move the valve to the 100% position using the jog buttons.
1079	Cal Error Status 1
1080	Bit1=Position Range Small, Bit2=Position < ADC Range, Bit3=Position > ADC RAnge, Bit4=No Motion Time Out, Bit5=Settle Time Out, Bit6=ILO Time Out
1081	Position Range Small
1082	Position < ADC Range
1083	Position > ADC RAnge
1084	ILO Time Out
1085	Cal Error Status 2
1086	Bit1=AO Range Small, Bit2=Cmd In Range Small, Bit3=Cmd In < ADC Range, Bit4=Cmd In > ADC Range, Bit5=Stroke Shift, Bit6=Stroke Span Increase, Bit7=Stroke Span Decrease
1087	Cmd In Range Small
1088	Cmd In < ADC Range
1089	Cmd In > ADC Range
1090	spare
1091	Control Status
1092	Bit1=Cmd Frequency WRN, Bit2=Cmd Frequency ALM, Bit3=Cmd Amplitude WRN, Bit4=Cmd Amplitude ALM, Bit5=Psn Frequency WRN, Bit6=Psn Frequency ALM, Bit7=Psn Amplitude WRN, Bit8=Psn Amplitude ALM
1093	Elec Board Status
1094	Bit1=Card 1 Fail WRN, Bit2=Card 2 Fail WRN, Bit3=Card 1 No Loop Pwr, Bit4=Card 2 No Loop Pwr, Bit5=Card 1 Error, Bit6=Card 2 Error, Bit7=Press Board Fail WRN, Bit8=Low Battery WRN
1095	Stroke/Fric Status
1096	Bit1=Reversed Spring, Bit2=Insufficient Spring, Bit3=No Spring
1097	Press Cal Status
1098	Bit1=Port S Out of Range, Bit2=Port A Out of Range, Bit3=Port B Out of Range, Bit4=Port S Range Small, Bit5=Port A Range Small, Bit6=Port B Range Small, Bit7=Pressure Sensor Fail
1099	Bit1=Stroke Cal In Prog, Bit2=Setting ILO, Bit3=Pressure Cal In Prog, Bit4=Friction Cal In Prog, Bit5=Cmd In Cal In Prog, Bit6=AO Cal In Prog, Bit7=Jog Cal set 100%
1100	Initial Duration:
1101	Strip chart initial duration.
1102	60 sec.
1103	Interval
1104	Strip chart interval.
1105	~ 2 sec.
1106	Stroke Time Close
1107	The time it takes to stroke the valve closed
1108	Stroke Time Open
1109	The time it takes to stroke the valve open
1110	Current Temp
1111	Current Temperature
1112	Max Lifetime Temp
1113	Maximum temperature reached for the life of the unit
1114	Min Lifetime Temp
1115	Minimum temperature reached for the life of the unit
1116	Max PowerUp Temp
1117	Maximum temperature reached since last power up
1118	Min PowerUp Temp
1119	Minimum temperature reached since last power up
1120	Max Reset Temp
1121	Maximum temperature reached since last reset of the unit
1122	Min Reset Temp
1123	Minimum temperature reached since last reset of the unit
1124	Tight Shutoff Hyst
1125	Position Tight Shutoff Hysteresis.
1126	Tight Shutoff Lower
1127	Position Tight Shut Off Lower Limit
1128	Tight Shutoff Upper
1129	Position Tight Shut off Upper Limit
1130	Area Units
1131	Units for area measurements.
1132	in²
1133	cm²
1134	Flow Units
1135	Units for flow measurements.
1136	Force Units
1137	Units for force measurements.
1138	Display the engineering units for pressure.
1139	Press Units
1140	Engineering units being used for ambient main board temperature measurement.
1141	Temp Units
1142	Travel Units
1143	Units for travel measurements.
1144	Select valve body material.
1145	Valve Body Mat
1146	Alloy 20
1147	Aluminum
1148	Bronze
1149	Carbon steel
1150	Special Alloy
1151	Hastelloy
1152	Inconel
1153	Monel 400
1154	Nickel
1155	Titanium
1156	Type 304
1157	Type 316
1158	Select valve body size in inches.
1159	Valve Body Size
1160	.25 INCH
1161	.5 INCH
1162	.75 INCH
1163	1.0 INCH
1164	1.25 INCH
1165	1.5 INCH
1166	2.0 INCH
1167	2.5 INCH
1168	3.0 INCH
1169	4.0 INCH
1170	5.0 INCH
1171	6.0 INCH
1172	8.0 INCH
1173	10.0 INCH
1174	12.0 INCH
1175	14.0 INCH
1176	16.0 INCH
1177	18.0 INCH
1178	20.0 INCH
1179	24.0 INCH
1180	28.0 INCH
1181	32.0 INCH
1182	36.0 INCH
1183	40.0 INCH
1184	Select valve bonnet type.
1185	Valve Bonnet Type
1186	Extended
1187	Bellows Seal
1188	Low Temperature
1189	Valve Cycles
1190	Valve Cycles.
1191	Valve Cycle Rate
1192	Valve Cycles center rate monitor.
1193	Pressure rating for the outlet of the valve.
1194	Outlet Press
1195	Select valve end connections.
1196	Valve End Conn
1197	Sep. Flange
1198	Integral Flange
1199	Weld end
1200	flangeless / Water
1201	Clamped
1202	Screwed
1203	FailDirection
1204	Direction valve will go in a failed state
1205	Fail Closed
1206	Fail Open
1207	Fail In Place
1208	OTHER
1209	FlowDirection
1210	Direction of the flow
1211	Flow Over
1212	Flow Under
1213	Select valve manufacturer.
1214	Valve Manuf.
1215	Valtek
1216	Select valve model type.
1217	Valve Model
1218	Mark One
1219	Mark One-X
1220	Mark 100
1221	Mark Two
1222	Mark Six
1223	Mark Eight
1224	Mark Ten (survivor)
1225	ShearStream SB
1226	ShearStream HP
1227	MaxFlo 3
1228	Valdisk BX
1229	FlowTop
1230	FlowPak
1231	FlowPro
1232	VariCool
1233	HpFlow
1234	LinedFlow
1235	TotalFlow
1236	ColdFlow
1237	DrainFlow
1238	SmallFlow
1239	CleanFlow
1240	Multi-Z
1241	020000
1242	025000
1243	030000
1244	185000
1245	Setball
1246	Duball
1247	Trunnball
1248	torex
1249	Unex
1250	GSV
1251	MaxFlo 4
1252	Durco
1253	Worcester
1254	Atomac
1255	McCANNA
1256	Nobel Alloy
1257	Valbart
1258	Argus
1259	Mark 200
1260	Select valve packing type.
1261	Valve Pack Type
1262	Single Packing PTFE
1263	Single Packing Graphite
1264	Double Packing PTFE
1265	Double Packing Graphite
1266	Spring Loaded
1267	valve pressure balance.
1268	Valve Press Bal
1269	Unbalanced
1270	Balanced
1271	Select valve body ANSI Pressure Rating (class).
1272	Press Class
1273	CL 150
1274	CL 300
1275	CL 600
1276	CL 900
1277	CL 1500
1278	CL 2500
1279	CL 4500
1280	PN 10
1281	PN 16
1282	PN 25
1283	PN 40
1284	PN 63
1285	PN 100
1286	PN 160
1287	PN 250
1288	PN 400
1289	PN 4000
1290	Travel for which this unit is rated.
1291	Rated Travel
1292	Select ANSI shutoff leakage class.
1293	Leak Class
1294	Class I
1295	Class II
1296	Class III
1297	Class IV
1298	Class V
1299	Class VI
1300	~2% Rate
1301	Valve serial number in the format, xxxxxx.xxx. Contains sales order number plus the page.
1302	Valve Ser.#
1303	Stem/shaft diameter in inches.
1304	Stem Dia.
1305	Stroke Length
1306	Stroke length in percent.
1307	Valve Travel
1308	Valve travel.
1309	Valve Travel Rate
1310	Valve travel center rate monitor.
1311	Select valve trim characteristics. (Informational use only)
1312	Valve Character.
1313	Equal %
1314	Quick Open
1315	bi-linear
1316	Select Valve Trim Diameter.
1317	Valve Trim Size
1318	0.10 - 0.12 in (2.5 - 3.0 mm)
1319	0.13 - 0.15 in (3.1 - 3.8 mm)
1320	0.16 - 0.19 in (3.9 - 4.8 mm)
1321	0.20 - 0.24 in (4.9 - 6.1 mm)
1322	0.25 - 0.30 in (6.2 - 7.6 mm)
1323	0.31 - 0.37 in (7.7 - 9.4 mm)
1324	0.38 - 0.45 in (9.5 - 11.4 mm)
1325	0.46 - 0.55 in (11.5 - 14.0 mm)
1326	0.56 - 0.67 in (14.1 - 17.0 mm)
1327	0.68 - 0.81 in (17.1 - 20.6 mm)
1328	0.82 - 0.98 in (20.7 - 24.9 mm)
1329	0.99 - 1.18 in (25.0 - 30.0 mm)
1330	1.19 - 1.42 in (30.1 - 36.1 mm)
1331	1.43 - 1.7 in (36.2 - 43 mm)
1332	1.8 - 2.1 in (44 - 54 mm)
1333	2.2 - 2.7 in (55 - 68 mm)
1334	2.8 - 3.3 in (69 - 84 mm)
1335	3.4 - 4.1 in (85 - 103 mm)
1336	4.2 - 4.9 in (104 - 125 mm)
1337	5.0 - 6.0 in (126 - 152 mm)
1338	6.1 - 7.3 in (153 - 184 mm)
1339	7.4 - 8.8 in (185 - 223 mm)
1340	8.9 - 10.5 in (224 - 268 mm)
1341	10.6 - 12.7 in (269 - 322 mm)
1342	12.8 - 15.2 in (323 - 386 mm)
1343	15.3 - 18.2 in (387 - 462 mm)
1344	18.3 - 21.8 in (463 - 552 mm)
1345	Select valve trim material.
1346	Valve Trim Mat
1347	Stainless Steel
1348	Stainless Steel (hardened)
1349	Alloy 6
1350	Soft Seated
1351	Special Alloys
1352	Select valve trim (standard, CavControl, MegaStream, etc.)
1353	Trim Type
1354	CavControl
1355	ChannelStream
1356	MegaStream
1357	Tiger-Tooth
1358	Stealth
1359	MicroCav
1360	CavStream
1361	MultiStream
1362	SilentPack
1363	Kammer Type I-III
1364	Z-Trim
1365	Multi-Stage
1366	V-Port
1367	CPT
1368	Ultra Low Flow
1369	Reduced Port
1370	Full Port
1371	Valve Type
1372	Select the type of valve
1373	Rotary
1374	Pressure rating for the inlet of the valve.
1375	Valve Inlet Press
1376	Vlv Cyc Dead Band
1377	Valve Cycle dead band.
1378	Vlv Cyc Full Warning
1379	Valve Cycles high end limit.
1380	Vlv Cyc Hi % Warning
1381	Valve Cycles high percent Warning.
1382	Vlv Cyc Initial Warning
1383	Valve Cycles high start limit.
1384	StrokeLength
1385	Valve stroke Length.
1386	Status bits
1387	Valve Trav/Cyc Reset
1388	Reset Valve Travel
1389	Reset Valve Cycles
1390	Vlv Trav Full Warning
1391	Valve travel high end limit.
1392	Vlv Trav Hi % Warning
1393	Vlv Trav Initial Warning
1394	Valve travel high start limit.
1395	Vlv Trav Dead Band
1396	Valve travel dead band.
1397	Too Few Data Bytes
1398	Device is Busy
1399	Command not implemented
1400	Events
1401	Last 32 events
1402	State
1403	Indication
1404	Cal Cmd In
1405	This method allows the user to Calibrate the command input A/D.
1406	Calibrate
1407	Calibrates the travel of the valve position (zero and span), and if auto tuning is enabled the gain values for the positioner are also calculated.
1408	View/Set Date/Time
1409	View and set the positioner date and time.
1410	Acquire Event History
1411	Execute this method to acquire the events. View the complete list of events (alarms, calibrations etc.). The latest event is shown first.
1412	Reset Factory Defaults
1413	This method allows the user to initiate a factory reset. This will reset all of the devices parameters back to factory defaults.
1414	method4
1415	method6
1416	Full Initial Setup
1417	This method directs the user through the initial steps to setup the positioner when it is fresh from the factory or has has a factory reset performed.
1418	Run PST
1419	This method allows the user to initiate a partial stroke test.
1420	Select Actuator Info
1421	Allows you to select your actuator manufacturer, model/size.
1422	Flowserve Logo
1423	Picture Lgx 420
1424	TEMP
1425	High Alarm
1426	High Warning
1427	Current Value
1428	Low Alarm
1429	Low Warning
1430	Warning
1431	Alarm
1432	Maximum
1433	Current
1434	Minimum
1435	Low
1436	High
1437	Cmd Pos Dev
1438	CMD
1439	POS
1440	DEV
1441	Travel
1442	Data Chart
1443	Real time data logger.
1444	Piezo Volts Chart
1445	View piezo volts and settings graphically.
1446	Pilot Response Chart
1447	View pilot relay response and settings graphically.
1448	Pilot Cycles Chart
1449	View pilot cycles and settings graphically.
1450	Pilot Travel Chart
1451	View pilot travel and settings graphically.
1452	Position Alert Chart
1453	View position and alert settings graphically.
1454	Position Deviation Chart
1455	View position deviation and settings graphically.
1456	Cmd. Pos. Dev.
1457	View command, position, deviation, and temperature graphically.
1458	Valve Tracking
1459	Valve Cycle Chart
1460	View current cycle count and settings graphically.
1461	Valve Travel Chart
1462	View current travel and settings graphically.
1463	Actuation error status indicators and mask settings.
1464	Actuator Health
1465	View health indicator of the actuator.
1466	Actuator Information
1467	Allows view and edit access to the actuator information parameters.
1468	Alarm Annunciators
1469	View and manage alerts and alarms.
1470	Annunciators
1471	View current warnings, alarms, and events.
1472	Burst Configuration
1473	Activate burst mode and change settings.
1474	Calibration
1475	Allows access to the calibration functions and variables of the device.
1476	View the status of indicators related to calibrations.
1477	Command Info
1478	Command, feedback, and temperature data.
1479	Command Data
1480	Allows user to view the health data of the device.
1481	Configuration
1482	Allows access to the configuration of the device for both viewing and editing.
1483	Control Config
1484	Allows access to the control configuration variables of the device for both viewing and editing.
1485	Control Health
1486	View and set health settings for the positioner control.
1487	View the modes or behavior configurations of the positioner.
1488	Cycle/Travel Status
1489	Cycle and travel status indicators and mask settings.
1490	Dashboard
1491	Display positioner status
1492	Data Monitor (GUI only)
1493	View a data strip chart.
1494	Device Config
1495	Allows use to view and set up the dip switches and aux cards of the device.
1496	Device Information
1497	Allows view and edit access to the device information parameters.
1498	Device Menu
1499	Device menu.
1500	Diagnostic Menu
1501	Top level menu.
1502	Dip Switch
1503	Dip switch settings.
1504	Electronic Detail Status
1505	Electronic detail error status indicators and mask settings.
1506	Electronic Config Status
1507	Presence of LCD board indicator.
1508	View Event Grid (GUI only)
1509	Acquire and view last 32 events.
1510	Feedback Status
1511	Position feedback status indicators and mask settings.
1512	Valve Stability
1513	Valve stability indicators and mask settings.
1514	Health
1515	View the overall health status.
1516	Hot Key Menu
1517	Hour Meters
1518	View the hour meters.
1519	Inner loop status indicators and mask settings.
1520	Local Interface
1521	Lock the local interface of the positioner and set a pin code. Locking the local interface prevents unauthorized changes from taking place at the positioner's button panel that affect the control or configuration of the positioner.
1522	Maintenance Menu
1523	Maintenance options
1524	Main Board Detail
1525	Main board detail status and mask settings.
1526	Main board status indicators and mask settings.
1527	Management Annunciators
1528	Management Annunciators contain settings with ranges.
1529	Mode Status
1530	Operational mode indicators and mask settings.
1531	Offline Diagnostics
1532	Configure and perform the partial stroke test and view the results.
1533	Offline Menu
1534	Offline menu.
1535	Online Diagnostics
1536	View data logger.
1537	Partial Stroke Test
1538	Run a partial stroke tests and view results.
1539	Piezo Voltage
1540	Displays the Piezo voltages.
1541	Pilot Relay
1542	View and set the Pilot Relay Response warning limits. The pilot relay response is a measure of how rapidly the pilot relay is following the pilot relay command. Longer times indicate slower response.
1543	Pilot Travel/Cycles
1544	Allows use to view travel and cycles of the pilot valve and edit the alarm end points of the device.
1545	Position Alert Settings
1546	View and configure position alert settings.
1547	Allows view and edit of the position alert parameters.
1548	Positioner Health
1549	View and set health settings for the positioner.
1550	Positioner Information
1551	Allows view and edit access to the tuning parameters.
1552	Positioner Tuning
1553	Position alert indicators and mask settings.
1554	PV Menu
1555	PV menu.
1556	Revs and SNs
1557	View inforamtion about the system revisions and serial numbers.
1558	LOGIX 420 Main menu selection
1559	Main Menu
1560	Software Detail Status
1561	Software detail error status and mask settings.
1562	Soft Limits and Shutoff
1563	Allows view and edit of the soft limits and tight shutoff parameters.
1564	Startup
1565	Initialization status indicators and mask settings.
1566	Diagnostic Values
1567	Allows user to view the diagnostic parameters of the device.
1568	Tech Annunciators
1569	View the status of low-level indicators.
1570	Temperature History
1571	View the temperature history.
1572	Command 3
1573	Select primary, secondary, tertiary, and fourth variables.
1574	Select Units
1575	Allows view and edit access to the unit parameters.
1576	User Preferences
1577	Allows view and edit access to user definable parameters.
1578	Valve Body Info
1579	Allows view and edit access to the valve trim and body parameters.
1580	Valve Health
1581	View the health of valve cycles and travel.
1582	Valve Trim Info
1583	Secondary Analog Channel Saturated
1584	Tertiary Analog Channel Saturated
1585	Quaternary Analog Channel Saturated
1586	Quinary Analog Channel Saturated
1587	Secondary Analog Channel Fixed
1588	Tertiary Analog Channel Fixed
1589	Quaternary Analog Channel Fixed
1590	Quinary Analog Channel Fixed
1591	PV Analog Channel Saturated
1592	PV Analog Channel Fixed
1593	Enable on token-passing data link layer only
1594	Enable on TDMA data link layer only
1595	Enable on both TDMA and token-passing data link layer
1596	Wireless
1597	WirelessHART Device
1598	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
1599	Primary
1600	Primary Analog Channel
1601	Secondary
1602	Secondary Analog Channel
1603	Tertiary
1604	Tertiary Analog Channel
1605	Quaternary
1606	Quaternary Analog Channel
1607	Quinary
1608	Quinary Analog Channel
1609	Critical Power Failure
1610	Lock all
1611	Trim not supported
1612	Configuration cannot be changed
1613	Locked by gateway
1614	Analog Input Channel
1615	Analog Output Channel
1616	Wired HART Enabled
1617	Enabled on Wired HART device connection only
1618	Wireless HART Enabled
1619	Enabled on WirelessHART device connection only
1620	Both Wired and WirelessHart Enabled
1621	Enabled on both Wired and WirelessHART connections
1622	8u
1623	8.3f
1624	.3f
1625	Burst Command
1626	WARNING This may affect the accuracy of the positioner. Continue?
1627	Yes;No
1628	Enter your initials. (up to 3 letters)
1629	Set the Command Input to 0% position then select Enter..
1630	Set the Command Input to 100% position then select Enter..
1631	Calibration complete
1632	Calibration not performed
1633	Do you wish to run Calibration? WARNING This proceedure will cause the valve to move.
1634	Please Wait, Stroke Cal in Progress...
1635	Please Wait, Setting ILO in Progress...
1636	Please Wait, Pressure Cal in Progress...
1637	Please Wait, Stroke/Pressure Cal in Progress...
1638	Please Wait, Friction Cal in Progress...
1639	Calibration Complete
1640	Do you wish to change the date/time? The current date and time is: %{CurrentDay} %{CurrentMonth} 20%{CurrentYear} %{CurrentHour}:%{CurrentMinutes}:%{CurrentSeconds}
1641	Select the Day
1642	1;2;3;4;5;6;7;8;9;10;11;12;13;14;15;16;17;18;19;20;21;22;23;24;25;26;27;28;29;30;31
1643	Select the Month
1644	January;February;March;April;May;June;July;August;September;October;November;December
1645	Select the Year
1646	2011;2012;2013;2014;2015;2016;2017;2018;2019;2020;2021;2022;2023;2024;2025;2026;2027;2028;2029;2030;Other
1647	Enter value for Year
1648	NewYear
1649	Value entered is out of range, must be between 2000 and 2099. Reenter
1650	Enter the Hour (24 Hour Clock)
1651	NewHour
1652	Value entered is out of range, must be between 0 and 23. Reenter
1653	Enter the Minutes (0 - 59)
1654	NewMin
1655	Value entered is out of range, must be between 0 and 59. Reenter
1656	The current date and time is: %{CurrentDay} %{CurrentMonth} 20%{CurrentYear} %{CurrentHour}:%{CurrentMinutes}:%{CurrentSeconds}
1657	Acquiring Events...
1658	Temp2
1659	,
1660
1661	:
1662	at
1663	WARNING Do you wish to continue? This proceedure will cause a loss of all user control and calibration parameters. The user will have to reconfigure the device.
1664	No;Yes
1665	Device has been reset. Device must now be reconfigured.
1666	Reset was not performed.
1667	WARNING This proceedure will cause the valve to move. Do you wish to continue?
1668	Select PST Type
1669	Baseline;Non Baseline
1670	Enter PST Start Position.
1671	LocStartPos
1672	Start Position out of range (0-100). Reenter
1673	Enter PST End Position.
1674	LocEndPos
1675	End Position out of range (0-100). Reenter
1676	Enter the Hold Time in seconds.
1677	LocHoldTime
1678	Enter the Ramp Time in seconds.
1679	LocRampTime
1680	Enter the PST Time Limit in seconds.
1681	LocTimeLimit
1682	PST in progress. Please Wait
1683	PST not performed
1684	Actuator manufacturer -
1685	Valtek (Piston);Kammer;Valtek (Diaphragm Rotary);Automax;NAF;Valtek (Diaphragm Linear);Fisher;Other
1686	Actuator size -
1687	25;50;100;100C;150C;200;200C;300;400;500;600;Other
1688	37;38;39;3D;47;48;49;4D;P0;P1;P2;P3;P4;P5;P6;P7;Other
1689	NR1;NR2;NR3;Other
1690	B050D;B063D;B085D;B100D;B115D;B125D;B150D;B175D;B200D;SNA250;SNA300;R205;R206;R207;R208;R310;R312;R314;R316;R414;R416;R418;R420;R422;R514;R516;R518;R520;R522;R524;Other
1691	-02;-11;-12;-21;-22;-31;-32;-41;-42;-51;-52;Other
1692	127;252;502;700;1502;3002;Other
1693	657-30;657-34;657-40;657-45;657-46;657-50;657-60;657-70;657-80;657-87;657-100;667-30;667-34;667-40;667-45;667-46;667-50;667-60;667-70;667-80;667-87;667-100;Other
1694	Enter value for Actuator Area
1695	ActArea
1696	Value entered is not reasonable, must be between 0 and 1000. Reenter
Reference ID	String