| 0 |
Lower range value too small |
| 1 |
Upper range value too high |
| 2 |
Invalid value selection |
| 3 |
Span too small |
| 4 |
Command Response Truncated |
| 5 |
Is online |
| 6 |
Offline |
| 7 |
Online |
| 8 |
old_MS_UnitLocal |
| 9 |
dummy |
| 10 |
Device name |
| 11 |
Shows the name of the transmitter |
| 12 |
iTEMP TMT72 |
| 13 |
Manufacturer ID |
| 14 |
Indication of the manufacturer ID with which the device is registered with the FieldComm Group. |
| 15 |
#.4X |
| 16 |
Manufacturer |
| 17 |
Indication of the manufacturer name. |
| 18 |
Endress+Hauser |
| 19 |
Firmware version |
| 20 |
Shows the device firmware version installed |
| 21 |
01.01 |
| 22 |
Serial number |
| 23 |
Indication of the serial number of the device. |
| 24 |
- none - |
| 25 |
Order code |
| 26 |
Shows the device order code |
| 27 |
- none - |
| 28 |
Device tag |
| 29 |
Enter the name for the measuring point |
| 30 |
???????????????????????????????? |
| 31 |
STD_ENPVersion_1 |
| 32 |
2.03.01 |
| 33 |
Access status |
| 34 |
Shows the access authorization to the parameters via the operating tool |
| 35 |
Operator |
| 36 |
Maintenance |
| 37 |
Production label |
| 38 |
Production |
| 39 |
Development |
| 40 |
Locking status |
| 41 |
Indicates the write protection with the highest priority that is currently active |
| 42 |
Write protected by hardware |
| 43 |
Device reset |
| 44 |
Reset the device configuration - either entirely or in part - to a defined state |
| 45 |
Not active |
| 46 |
Restart device |
| 47 |
To delivery settings |
| 48 |
To factory defaults |
| 49 |
Extended order code |
| 50 |
The extended order code indicates the version of all the features of the product structure for the device. |
| 51 |
|
| 52 |
Extended order code 2 |
| 53 |
Extended order code 3 |
| 54 |
STD_UDLFeature_1 |
| 55 |
Upload support |
| 56 |
Download support |
| 57 |
STD_UDLOperationCode_1 |
| 58 |
Initiate upload |
| 59 |
Download to different device |
| 60 |
Download to identical device |
| 61 |
Abort up-/download |
| 62 |
Terminate up-/download |
| 63 |
Confirm download status |
| 64 |
STD_UDLStatus_1 |
| 65 |
Up-/download inactive |
| 66 |
Download temporary impossible |
| 67 |
Upload active |
| 68 |
Download active |
| 69 |
Up-/Download verification active |
| 70 |
Download succeeded |
| 71 |
Download terminated with warnings |
| 72 |
Download failed |
| 73 |
STD_UDLVerificationDelay_1 |
| 74 |
s |
| 75 |
Hardware revision |
| 76 |
Indication of the hardware revision of the device. |
| 77 |
01.01.00 |
| 78 |
STD_UDLRevision_1 |
| 79 |
Password |
| 80 |
Enter password to gain access to the functions of the user role. |
| 81 |
|
| 82 |
Status password entry |
| 83 |
Status of the password verification. |
| 84 |
-------- |
| 85 |
Wrong password |
| 86 |
Password rule violated |
| 87 |
Password accepted |
| 88 |
Permission denied |
| 89 |
Confirm PW mismatch |
| 90 |
Reset password accepted |
| 91 |
Userrole invalid |
| 92 |
Wrong order of entry |
| 93 |
Status old password entry |
| 94 |
Old password |
| 95 |
Enter the current password to start a password change |
| 96 |
New password |
| 97 |
Enter a new password. |
| 98 |
Confirm new password |
| 99 |
Confirmation new password |
| 100 |
Reset password |
| 101 |
Enter a code to reset the current password. |
| 102 |
Select userrole |
| 103 |
Selection of the desired user role |
| 104 |
Logout |
| 105 |
STD_PasswordIsDefined_1 |
| 106 |
No |
| 107 |
Yes |
| 108 |
STD_PasswordActionChooser_1 |
| 109 |
Please select |
| 110 |
Define password |
| 111 |
Enter password |
| 112 |
Change password |
| 113 |
Delete password |
| 114 |
Forgot password? |
| 115 |
HART date code |
| 116 |
Use this function to define date information for individual use. |
| 117 |
2010-01-01 |
| 118 |
HART descriptor |
| 119 |
Use this function to define a description for the measuring point. |
| 120 |
???????????????? |
| 121 |
Device ID |
| 122 |
Shows the device ID for identifying the device in a HART network |
| 123 |
#.8X |
| 124 |
HART message |
| 125 |
Enter a HART message |
| 126 |
No. of preambles |
| 127 |
Defines the number o preambles in the HART telegram |
| 128 |
HART address |
| 129 |
Enter the address via which the data exchange takes place via HART protocol. |
| 130 |
Configuration changed |
| 131 |
Indicates whether the configuration of the device has been changed by a master (primary or secondary). |
| 132 |
Primary master |
| 133 |
Secondary master |
| 134 |
Device revision |
| 135 |
Display the device revision with which the device is registered with the HART® FieldComm Group. |
| 136 |
#.2X |
| 137 |
HART revision |
| 138 |
Display the HART protocol revision of the measuring device |
| 139 |
Software revision |
| 140 |
Displays the software revision of the measuring device |
| 141 |
HART short tag |
| 142 |
Defines short tag for the measuring point. |
| 143 |
???????? |
| 144 |
HO_LoopCurrentMode_1 |
| 145 |
Disabled |
| 146 |
Enabled |
| 147 |
Device type |
| 148 |
Shows the device type with which the measuring device is registered with the HART Communication Foundation |
| 149 |
Sensor value |
| 150 |
Indication of the measured value at the sensor input. |
| 151 |
.2f |
| 152 |
Sensor raw value |
| 153 |
Indication of the non linearized mV/Ohm value. |
| 154 |
Sensor type |
| 155 |
Selection option of the sensor type for the sensor input. |
| 156 |
Pt100 IEC60751, a=0.00385 (1) |
| 157 |
Pt200 IEC60751, a=0.00385 (2) |
| 158 |
Pt500 IEC60751, a=0.00385 (3) |
| 159 |
Pt1000 IEC60751, a=0.00385 (4) |
| 160 |
Pt100 JIS C1604, a=0.003916 (5) |
| 161 |
Ni100 DIN 43760, a=0.00618 (6) |
| 162 |
Ni120 DIN 43760, a=0.00618 (7) |
| 163 |
Ni100 OIML/GOST 6651-09, a=0.00617 (12) |
| 164 |
Ni120 OIML/GOST 6651-09, a=0.00617 (13) |
| 165 |
Type A (W5Re-W20Re) IEC60584-2013 (30) |
| 166 |
Type B (PtRh30-PtRh6) IEC60584 (31) |
| 167 |
Type C (W5Re-W26Re) IEC60584 (32) |
| 168 |
Type D (W3Re-W25Re) ASTM E988-96 (33) |
| 169 |
Type E (NiCr-CuNi) IEC60584 (34) |
| 170 |
Type J (Fe-CuNi) IEC60584 (35) |
| 171 |
Type K (NiCr-Ni) IEC60584 (36) |
| 172 |
Type N (NiCrSi-NiSi) IEC60584 (37) |
| 173 |
Type R (PtRh13-Pt) IEC60584 (38) |
| 174 |
Type S (PtRh10-Pt) IEC60584 (39) |
| 175 |
Type T (Cu-CuNi) IEC60584 (40) |
| 176 |
Type L (Fe-CuNi) DIN43710 (41) |
| 177 |
Type L (NiCr-CuNi) GOST R8.8585-01 (43) |
| 178 |
Type U (Cu-CuNi) DIN43710 (42) |
| 179 |
Pt50 GOST 6651-94, a=0.00391 (8) |
| 180 |
Pt100 GOST 6651-94, a=0.00391 (9) |
| 181 |
Cu50 GOST 6651-09, a=0.00428 (10) |
| 182 |
Cu100 OIML/GOST 6651-09, a=0.00428 (11) |
| 183 |
Cu50 OIML R84:2003, a=0.00428 (10) |
| 184 |
Cu50 OIML/GOST 6651-94, a=0,00426 (14) |
| 185 |
RTD Platinium (Callendar/van Dusen) |
| 186 |
RTD Poly Nickel (OIML R84, GOST 6651-94) |
| 187 |
RTD Polynomial Copper (OIML R84:2003) |
| 188 |
10...400 Ohm |
| 189 |
10...2000 Ohm |
| 190 |
-20...100 mV |
| 191 |
ST1_SensorMinSpan_1 |
| 192 |
Sensor upper limit |
| 193 |
Indication of the upper, physical sensor range. |
| 194 |
Sensor lower limit |
| 195 |
Indication of the lower, physical sensor range. |
| 196 |
Sensor max value |
| 197 |
Indication of the maximum measured temperature in the past. |
| 198 |
Sensor min value |
| 199 |
Indication of the minimum measured temperature in the past. |
| 200 |
Sensor offset |
| 201 |
Setting of the zero adjustment of the measured sensor value. |
| 202 |
Connection type |
| 203 |
Selection of the sensor connection type |
| 204 |
2- wire |
| 205 |
3- wire |
| 206 |
4- wire |
| 207 |
2-wire compensation |
| 208 |
Setting of the resistance for the 2-wire RTD compensation. |
| 209 |
Ohm |
| 210 |
Reference junction |
| 211 |
Selection of reference junction measurement for temperature compensation in thermocouples. |
| 212 |
Internal measurement |
| 213 |
Fixed Value |
| 214 |
Measured value ext. sensor |
| 215 |
RJ preset value |
| 216 |
Setting of the value for the external temperature compensation. |
| 217 |
Call./v. Dusen coeff. A |
| 218 |
Setting of the Callendar/van Dusen coefficient A for the linearization based on the Callendar-Van Dusen method. |
| 219 |
.5e |
| 220 |
Call./v. Dusen coeff. B |
| 221 |
Setting of the Callendar/van Dusen coefficient B for the linearization based on the Callendar-Van Dusen method. |
| 222 |
Call./v. Dusen coeff. C |
| 223 |
Setting of the Callendar/van Dusen coefficient C for the linearization based on the Callendar-Van Dusen method. |
| 224 |
Call./v. Dusen coeff. R0 |
| 225 |
Setting of the R0 value for the linearization based on the Callendar-Van Dusen method. |
| 226 |
.3f |
| 227 |
Polynomial coeff. A |
| 228 |
Setting of the Polynomial coefficient A for Sensor linearization of copper/nickel resistance thermometers (RTD). |
| 229 |
Polynomial coeff. B |
| 230 |
Setting of the Polynomial coefficient B for Sensor linearization of copper/nickel resistance thermometers (RTD). |
| 231 |
Polynomial coeff. R0 |
| 232 |
Setting of the R0 value for Sensor linearization of copper/nickel resistance thermometers (RTD). |
| 233 |
Sensor simulation value |
| 234 |
Use this function to enter a simulation value of the process variable. |
| 235 |
Sensor simulation |
| 236 |
Use this function to activate the simulation of the process variable. |
| 237 |
Off |
| 238 |
On |
| 239 |
Reset sensor min/max values |
| 240 |
Reset the min/max values of the sensor. |
| 241 |
No |
| 242 |
Yes |
| 243 |
ST1_SensorRawUnit_1 |
| 244 |
mV |
| 245 |
Limit corrosion detection |
| 246 |
Enter the limit for corrosion detection |
| 247 |
.0f |
| 248 |
Sensor line resistance |
| 249 |
Indication of the highest measured resistance value of one sensor wire. |
| 250 |
Device temperature |
| 251 |
Indication of the current temperature of the electronics. |
| 252 |
DevTemp_Unit_1 |
| 253 |
°C |
| 254 |
°F |
| 255 |
K |
| 256 |
DevTemp_UnitDifference_1 |
| 257 |
Device temperature max |
| 258 |
Indication of the maximum measured electronic temperature in the past. |
| 259 |
Device temperature min |
| 260 |
Indication of the minimum measured electronic temperature in the past. |
| 261 |
Reset device temp. min/max values |
| 262 |
Reset min/max- values of electronic temperature to their default values. |
| 263 |
Unit |
| 264 |
Selection of the unit for all measured values. |
| 265 |
°C |
| 266 |
°F |
| 267 |
K |
| 268 |
Ohm |
| 269 |
mV |
| 270 |
Mains filter |
| 271 |
Selection of the mains filter for the A/D converter. |
| 272 |
50 Hz |
| 273 |
60 Hz |
| 274 |
MS_UnitDifference_1 |
| 275 |
Thermocouple diagnostic |
| 276 |
Turn off the 'Sensor corrosion' and 'sensor interrupted' diagnostic functions for TC measurement. |
| 277 |
MS_HousingStyle_1 |
| 278 |
Head mounted screw terminals |
| 279 |
DIN rail 125mm spring terminals |
| 280 |
DIN rail 175mm screw terminals |
| 281 |
Field housing screw terminals |
| 282 |
Head mounted spring terminals |
| 283 |
DIN rail 125mm screw terminals |
| 284 |
DIN rail 175mm spring terminals |
| 285 |
Field housing spring terminals |
| 286 |
Configuration counter |
| 287 |
Indication of the meter reading for changes of device parameters. |
| 288 |
Alarm delay |
| 289 |
Setting of the duration how long diagnostic messages are suppressed. |
| 290 |
Operating time |
| 291 |
Indicates how long the device has been in operation |
| 292 |
h |
| 293 |
Diagnostic event simulation |
| 294 |
Select a diagnostic event to simulate this event |
| 295 |
x041-Sensor interrupted |
| 296 |
x042-Sensor corroded |
| 297 |
x043-Short circuit |
| 298 |
x047-Sensor limit reached-Sensor 1 |
| 299 |
x047-Sensor limit reached-Device temperature |
| 300 |
x047-Sensor limit reached-Sensor RJ |
| 301 |
x145-Compensation refrence point-Sensor 1 |
| 302 |
x201-Electronics faulty |
| 303 |
x201-Electronics faulty-Sensor 1 |
| 304 |
x201-Electronics faulty-Device temperature |
| 305 |
x201-Electronics faulty-Sensor RJ |
| 306 |
x221-Reference sensor defective |
| 307 |
x221-Reference sensor defective-Sensor RJ |
| 308 |
x401-Factory reset active |
| 309 |
x402-Initialization active |
| 310 |
x402-Initialization active-Sensor 1 |
| 311 |
x402-Initialization active-Device temperature |
| 312 |
x402-Initialization active-Sensor RJ |
| 313 |
x410-Data transfer failed |
| 314 |
x411-Up-/download active |
| 315 |
x435-Linearization faulty-Sensor 1 |
| 316 |
x435-Linearization faulty |
| 317 |
x435-Linearization faulty-Sensor RJ |
| 318 |
x531-Factory adjustment missing-Sensor 1 |
| 319 |
x531-Factory adjustment missing-Current output |
| 320 |
x537-Configuration |
| 321 |
x537-Configuration-Sensor 1 |
| 322 |
x537-Configuration-Current output |
| 323 |
x801-Supply voltage too low |
| 324 |
x825-Operating temperature |
| 325 |
x844-Process value out of specification |
| 326 |
DS_ActualDiagnostics1NE107_1 |
| 327 |
OK |
| 328 |
041-Sensor interrupted |
| 329 |
042-Sensor corroded |
| 330 |
043-Short circuit |
| 331 |
047-Sensor limit reached-Sensor 1 |
| 332 |
047-Sensor limit reached-Device temperature |
| 333 |
047-Sensor limit reached-Sensor RJ |
| 334 |
145-Compensation refrence point-Sensor 1 |
| 335 |
201-Electronics faulty |
| 336 |
201-Electronics faulty-Sensor 1 |
| 337 |
201-Electronics faulty-Device temperature |
| 338 |
201-Electronics faulty-Sensor RJ |
| 339 |
221-Reference sensor defective |
| 340 |
221-Reference sensor defective-Sensor RJ |
| 341 |
401-Factory reset active |
| 342 |
402-Initialization active |
| 343 |
402-Initialization active-Sensor 1 |
| 344 |
402-Initialization active-Device temperature |
| 345 |
402-Initialization active-Sensor RJ |
| 346 |
410-Data transfer failed |
| 347 |
411-Up-/download active |
| 348 |
435-Linearization faulty-Sensor 1 |
| 349 |
435-Linearization faulty |
| 350 |
435-Linearization faulty-Sensor RJ |
| 351 |
485-Process variable simulation active-Sensor 1 |
| 352 |
485-Process variable simulation active-Device temperature |
| 353 |
491-Output simulation-Current output |
| 354 |
495-Diagnostic event simulation active |
| 355 |
531-Factory adjustment missing-Sensor 1 |
| 356 |
531-Factory adjustment missing-Current output |
| 357 |
537-Configuration |
| 358 |
537-Configuration-Sensor 1 |
| 359 |
537-Configuration-Current output |
| 360 |
582-Sensor diagnostics TC deactivated |
| 361 |
801-Supply voltage too low |
| 362 |
825-Operating temperature |
| 363 |
844-Process value out of specification |
| 364 |
S041-Sensor interrupted |
| 365 |
S042-Sensor corroded |
| 366 |
S043-Short circuit |
| 367 |
S047-Sensor limit reached-Sensor 1 |
| 368 |
S047-Sensor limit reached-Device temperature |
| 369 |
S047-Sensor limit reached-Sensor RJ |
| 370 |
S145-Compensation refrence point-Sensor 1 |
| 371 |
S201-Electronics faulty |
| 372 |
S201-Electronics faulty-Sensor 1 |
| 373 |
S201-Electronics faulty-Device temperature |
| 374 |
S201-Electronics faulty-Sensor RJ |
| 375 |
S221-Reference sensor defective |
| 376 |
S221-Reference sensor defective-Sensor RJ |
| 377 |
S401-Factory reset active |
| 378 |
S402-Initialization active |
| 379 |
S402-Initialization active-Sensor 1 |
| 380 |
S402-Initialization active-Device temperature |
| 381 |
S402-Initialization active-Sensor RJ |
| 382 |
S410-Data transfer failed |
| 383 |
S411-Up-/download active |
| 384 |
S435-Linearization faulty-Sensor 1 |
| 385 |
S435-Linearization faulty |
| 386 |
S435-Linearization faulty-Sensor RJ |
| 387 |
S485-Process variable simulation active-Sensor 1 |
| 388 |
S485-Process variable simulation active-Device temperature |
| 389 |
S491-Output simulation-Current output |
| 390 |
S495-Diagnostic event simulation active |
| 391 |
S531-Factory adjustment missing-Sensor 1 |
| 392 |
S531-Factory adjustment missing-Current output |
| 393 |
S537-Configuration |
| 394 |
S537-Configuration-Sensor 1 |
| 395 |
S537-Configuration-Current output |
| 396 |
S582-Sensor diagnostics TC deactivated |
| 397 |
S801-Supply voltage too low |
| 398 |
S825-Operating temperature |
| 399 |
S844-Process value out of specification |
| 400 |
C041-Sensor interrupted |
| 401 |
C042-Sensor corroded |
| 402 |
C043-Short circuit |
| 403 |
C047-Sensor limit reached-Sensor 1 |
| 404 |
C047-Sensor limit reached-Device temperature |
| 405 |
C047-Sensor limit reached-Sensor RJ |
| 406 |
C145-Compensation refrence point-Sensor 1 |
| 407 |
C201-Electronics faulty |
| 408 |
C201-Electronics faulty-Sensor 1 |
| 409 |
C201-Electronics faulty-Device temperature |
| 410 |
C201-Electronics faulty-Sensor RJ |
| 411 |
C221-Reference sensor defective |
| 412 |
C221-Reference sensor defective-Sensor RJ |
| 413 |
C401-Factory reset active |
| 414 |
C402-Initialization active |
| 415 |
C402-Initialization active-Sensor 1 |
| 416 |
C402-Initialization active-Device temperature |
| 417 |
C402-Initialization active-Sensor RJ |
| 418 |
C410-Data transfer failed |
| 419 |
C411-Up-/download active |
| 420 |
C435-Linearization faulty-Sensor 1 |
| 421 |
C435-Linearization faulty |
| 422 |
C435-Linearization faulty-Sensor RJ |
| 423 |
C485-Process variable simulation active-Sensor 1 |
| 424 |
C485-Process variable simulation active-Device temperature |
| 425 |
C491-Output simulation-Current output |
| 426 |
C495-Diagnostic event simulation active |
| 427 |
C531-Factory adjustment missing-Sensor 1 |
| 428 |
C531-Factory adjustment missing-Current output |
| 429 |
C537-Configuration |
| 430 |
C537-Configuration-Sensor 1 |
| 431 |
C537-Configuration-Current output |
| 432 |
C582-Sensor diagnostics TC deactivated |
| 433 |
C801-Supply voltage too low |
| 434 |
C825-Operating temperature |
| 435 |
C844-Process value out of specification |
| 436 |
M041-Sensor interrupted |
| 437 |
M042-Sensor corroded |
| 438 |
M043-Short circuit |
| 439 |
M047-Sensor limit reached-Sensor 1 |
| 440 |
M047-Sensor limit reached-Device temperature |
| 441 |
M047-Sensor limit reached-Sensor RJ |
| 442 |
M145-Compensation refrence point-Sensor 1 |
| 443 |
M201-Electronics faulty |
| 444 |
M201-Electronics faulty-Sensor 1 |
| 445 |
M201-Electronics faulty-Device temperature |
| 446 |
M201-Electronics faulty-Sensor RJ |
| 447 |
M221-Reference sensor defective |
| 448 |
M221-Reference sensor defective-Sensor RJ |
| 449 |
M401-Factory reset active |
| 450 |
M402-Initialization active |
| 451 |
M402-Initialization active-Sensor 1 |
| 452 |
M402-Initialization active-Device temperature |
| 453 |
M402-Initialization active-Sensor RJ |
| 454 |
M410-Data transfer failed |
| 455 |
M411-Up-/download active |
| 456 |
M435-Linearization faulty-Sensor 1 |
| 457 |
M435-Linearization faulty |
| 458 |
M435-Linearization faulty-Sensor RJ |
| 459 |
M485-Process variable simulation active-Sensor 1 |
| 460 |
M485-Process variable simulation active-Device temperature |
| 461 |
M491-Output simulation-Current output |
| 462 |
M495-Diagnostic event simulation active |
| 463 |
M531-Factory adjustment missing-Sensor 1 |
| 464 |
M531-Factory adjustment missing-Current output |
| 465 |
M537-Configuration |
| 466 |
M537-Configuration-Sensor 1 |
| 467 |
M537-Configuration-Current output |
| 468 |
M582-Sensor diagnostics TC deactivated |
| 469 |
M801-Supply voltage too low |
| 470 |
M825-Operating temperature |
| 471 |
M844-Process value out of specification |
| 472 |
F041-Sensor interrupted |
| 473 |
F042-Sensor corroded |
| 474 |
F043-Short circuit |
| 475 |
F047-Sensor limit reached-Sensor 1 |
| 476 |
F047-Sensor limit reached-Device temperature |
| 477 |
F047-Sensor limit reached-Sensor RJ |
| 478 |
F145-Compensation refrence point-Sensor 1 |
| 479 |
F201-Electronics faulty |
| 480 |
F201-Electronics faulty-Sensor 1 |
| 481 |
F201-Electronics faulty-Device temperature |
| 482 |
F201-Electronics faulty-Sensor RJ |
| 483 |
F221-Reference sensor defective |
| 484 |
F221-Reference sensor defective-Sensor RJ |
| 485 |
F401-Factory reset active |
| 486 |
F402-Initialization active |
| 487 |
F402-Initialization active-Sensor 1 |
| 488 |
F402-Initialization active-Device temperature |
| 489 |
F402-Initialization active-Sensor RJ |
| 490 |
F410-Data transfer failed |
| 491 |
F411-Up-/download active |
| 492 |
F435-Linearization faulty-Sensor 1 |
| 493 |
F435-Linearization faulty |
| 494 |
F435-Linearization faulty-Sensor RJ |
| 495 |
F485-Process variable simulation active-Sensor 1 |
| 496 |
F485-Process variable simulation active-Device temperature |
| 497 |
F491-Output simulation-Current output |
| 498 |
F495-Diagnostic event simulation active |
| 499 |
F531-Factory adjustment missing-Sensor 1 |
| 500 |
F531-Factory adjustment missing-Current output |
| 501 |
F537-Configuration |
| 502 |
F537-Configuration-Sensor 1 |
| 503 |
F537-Configuration-Current output |
| 504 |
F582-Sensor diagnostics TC deactivated |
| 505 |
F801-Supply voltage too low |
| 506 |
F825-Operating temperature |
| 507 |
F844-Process value out of specification |
| 508 |
DS_ActualDiagnostics2NE107_1 |
| 509 |
DS_ActualDiagnostics3NE107_1 |
| 510 |
Actual diagnostics 1 |
| 511 |
Displays the currently active diagnostic message with the highest priority. |
| 512 |
OK |
| 513 |
041-Sensor interrupted |
| 514 |
042-Sensor corroded |
| 515 |
043-Short circuit |
| 516 |
047-Sensor limit reached |
| 517 |
145-Compensation refrence point |
| 518 |
201-Electronics faulty |
| 519 |
221-Reference sensor defective |
| 520 |
401-Factory reset active |
| 521 |
402-Initialization active |
| 522 |
410-Data transfer failed |
| 523 |
411-Up-/download active |
| 524 |
435-Linearization faulty |
| 525 |
485-Process variable simulation active |
| 526 |
491-Output simulation |
| 527 |
495-Diagnostic event simulation active |
| 528 |
531-Factory adjustment missing |
| 529 |
537-Configuration |
| 530 |
582-Sensor diagnostics TC deactivated |
| 531 |
801-Supply voltage too low |
| 532 |
825-Operating temperature |
| 533 |
844-Process value out of specification |
| 534 |
S041-Sensor interrupted |
| 535 |
S042-Sensor corroded |
| 536 |
S043-Short circuit |
| 537 |
S047-Sensor limit reached |
| 538 |
S145-Compensation refrence point |
| 539 |
S201-Electronics faulty |
| 540 |
S221-Reference sensor defective |
| 541 |
S401-Factory reset active |
| 542 |
S402-Initialization active |
| 543 |
S410-Data transfer failed |
| 544 |
S411-Up-/download active |
| 545 |
S435-Linearization faulty |
| 546 |
S485-Process variable simulation active |
| 547 |
S491-Output simulation |
| 548 |
S495-Diagnostic event simulation active |
| 549 |
S531-Factory adjustment missing |
| 550 |
S537-Configuration |
| 551 |
S582-Sensor diagnostics TC deactivated |
| 552 |
S801-Supply voltage too low |
| 553 |
S825-Operating temperature |
| 554 |
S844-Process value out of specification |
| 555 |
C041-Sensor interrupted |
| 556 |
C042-Sensor corroded |
| 557 |
C043-Short circuit |
| 558 |
C047-Sensor limit reached |
| 559 |
C145-Compensation refrence point |
| 560 |
C201-Electronics faulty |
| 561 |
C221-Reference sensor defective |
| 562 |
C401-Factory reset active |
| 563 |
C402-Initialization active |
| 564 |
C410-Data transfer failed |
| 565 |
C411-Up-/download active |
| 566 |
C435-Linearization faulty |
| 567 |
C485-Process variable simulation active |
| 568 |
C491-Output simulation |
| 569 |
C495-Diagnostic event simulation active |
| 570 |
C531-Factory adjustment missing |
| 571 |
C537-Configuration |
| 572 |
C582-Sensor diagnostics TC deactivated |
| 573 |
C801-Supply voltage too low |
| 574 |
C825-Operating temperature |
| 575 |
C844-Process value out of specification |
| 576 |
M041-Sensor interrupted |
| 577 |
M042-Sensor corroded |
| 578 |
M043-Short circuit |
| 579 |
M047-Sensor limit reached |
| 580 |
M145-Compensation refrence point |
| 581 |
M201-Electronics faulty |
| 582 |
M221-Reference sensor defective |
| 583 |
M401-Factory reset active |
| 584 |
M402-Initialization active |
| 585 |
M410-Data transfer failed |
| 586 |
M411-Up-/download active |
| 587 |
M435-Linearization faulty |
| 588 |
M485-Process variable simulation active |
| 589 |
M491-Output simulation |
| 590 |
M495-Diagnostic event simulation active |
| 591 |
M531-Factory adjustment missing |
| 592 |
M537-Configuration |
| 593 |
M582-Sensor diagnostics TC deactivated |
| 594 |
M801-Supply voltage too low |
| 595 |
M825-Operating temperature |
| 596 |
M844-Process value out of specification |
| 597 |
F041-Sensor interrupted |
| 598 |
F042-Sensor corroded |
| 599 |
F043-Short circuit |
| 600 |
F047-Sensor limit reached |
| 601 |
F145-Compensation refrence point |
| 602 |
F201-Electronics faulty |
| 603 |
F221-Reference sensor defective |
| 604 |
F401-Factory reset active |
| 605 |
F402-Initialization active |
| 606 |
F410-Data transfer failed |
| 607 |
F411-Up-/download active |
| 608 |
F435-Linearization faulty |
| 609 |
F485-Process variable simulation active |
| 610 |
F491-Output simulation |
| 611 |
F495-Diagnostic event simulation active |
| 612 |
F531-Factory adjustment missing |
| 613 |
F537-Configuration |
| 614 |
F582-Sensor diagnostics TC deactivated |
| 615 |
F801-Supply voltage too low |
| 616 |
F825-Operating temperature |
| 617 |
F844-Process value out of specification |
| 618 |
Actual diag 1 channel |
| 619 |
Indication of the module which this diagnostics message refers to. |
| 620 |
Sensor 1 |
| 621 |
Current output |
| 622 |
Sensor RJ |
| 623 |
Actual diagnostics 2 |
| 624 |
Displays the currently active diagnostic message with the second highest priority. |
| 625 |
Actual diag 2 channel |
| 626 |
Actual diagnostics 3 |
| 627 |
Shows the currently active diagnostic message with the third highest priority. |
| 628 |
Actual diag 3 channel |
| 629 |
Timestamp 1 |
| 630 |
Timestamp of the diagnostic message. |
| 631 |
Timestamp 2 |
| 632 |
Timestamp 3 |
| 633 |
Shows the timestamp of the previous diagnostic message |
| 634 |
Timestamp 4 |
| 635 |
Timestamp 5 |
| 636 |
Timestamp 6 |
| 637 |
Timestamp 7 |
| 638 |
Timestamp 8 |
| 639 |
Timestamp 9 |
| 640 |
Timestamp 10 |
| 641 |
Previous diagnostics 1 |
| 642 |
Display of the diagnostic messages that have occurred in the past. |
| 643 |
Previous diag 1 channel |
| 644 |
Indication of the channel which this diagnostics message refers. |
| 645 |
Previous diagnostics 2 |
| 646 |
Previous diag 2 channel |
| 647 |
Previous diagnostics 3 |
| 648 |
Previous diag 3 channel |
| 649 |
Previous diagnostics 4 |
| 650 |
Previous diag 4 channel |
| 651 |
Previous diagnostics 5 |
| 652 |
Previous diag 5 channel |
| 653 |
Previous diagnostics 6 |
| 654 |
Previous diag 6 channel |
| 655 |
Previous diagnostics 7 |
| 656 |
Previous diag 7 channel |
| 657 |
Previous diagnostics 8 |
| 658 |
Previous diag 8 channel |
| 659 |
Previous diagnostics 9 |
| 660 |
Previous diag 9 channel |
| 661 |
Previous diagnostics 10 |
| 662 |
Previous diag 10 channel |
| 663 |
Do not show this message again |
| 664 |
|
| 665 |
DS_CommissioningEvent_1 |
| 666 |
Idle |
| 667 |
Start |
| 668 |
Cancel |
| 669 |
Finished |
| 670 |
DS_CommissioningWizardFeedback_1 |
| 671 |
TimeoutOrDisconnect |
| 672 |
Output current |
| 673 |
Shows the actual calculated value of the output current |
| 674 |
mA |
| 675 |
Current output simulation |
| 676 |
Switch the simulation of the current output on and off |
| 677 |
Value current output |
| 678 |
Enter the current value for simulation |
| 679 |
Current trimming 20 mA |
| 680 |
Setting of the correction value for the current output at the upper range value 20 mA. |
| 681 |
Current trimming 4 mA |
| 682 |
Setting of the correction value for the current output at the lower range value 4 mA. |
| 683 |
4 mA value |
| 684 |
Enter 4 mA value |
| 685 |
20 mA value |
| 686 |
Enter 20 mA value |
| 687 |
Percent of range |
| 688 |
Indication of the measured value in % of the span. |
| 689 |
% |
| 690 |
Failure current |
| 691 |
Setting of the value the current output adopts in an alarm condition. |
| 692 |
Failure mode |
| 693 |
Selection of the failure signal level of the current output in case of an error. |
| 694 |
High alarm |
| 695 |
Low alarm |
| 696 |
CO_MinSpan_1 |
| 697 |
Assign current output (PV) |
| 698 |
Allocation of a measuring variable to the primary HART variable (PV). |
| 699 |
Assign SV |
| 700 |
Allocation of a measuring variable to the secondary HART variable (SV). |
| 701 |
Assign TV |
| 702 |
Allocation of a measuring variable to the third HART variable (TV). |
| 703 |
Assign QV |
| 704 |
Allocation of a measuring variable to the fourth HART variable (QV). |
| 705 |
PV |
| 706 |
Indication of the primary HART variable (PV). |
| 707 |
SV |
| 708 |
Indication of the secondary HART variable (SV). |
| 709 |
TV |
| 710 |
Indication of the third HART variable (TV). |
| 711 |
QV |
| 712 |
Indication of the fourth HART variable (QV). |
| 713 |
Damping |
| 714 |
Setting of the time constant for the damping of the output current. |
| 715 |
Display interval |
| 716 |
Set time measured values are shown on display if display alternates between values |
| 717 |
Format display |
| 718 |
Select how measured values are shown on the display |
| 719 |
Value only |
| 720 |
Value + Bargraph |
| 721 |
Value 1 display |
| 722 |
Select the measured value that is shown on the local display |
| 723 |
Process value |
| 724 |
Decimal places 1 |
| 725 |
Select the number of decimal places for the display value |
| 726 |
Automatic |
| 727 |
x |
| 728 |
x.x |
| 729 |
x.xx |
| 730 |
x.xxx |
| 731 |
x.xxxx |
| 732 |
Value 2 display |
| 733 |
Selection of the measured value that is shown on the local display |
| 734 |
Decimal places 2 |
| 735 |
Value 3 display |
| 736 |
Selection of the measured value that is shown on the local display. |
| 737 |
Decimal places 3 |
| 738 |
Bluetooth |
| 739 |
Enable or disable Bluetooth function |
| 740 |
BT_Available_1 |
| 741 |
Process Unit Tag |
| 742 |
Enter the process unit in which the device is installed. |
| 743 |
Location Description |
| 744 |
Enter a description of the location so that the device can be located in. |
| 745 |
Longitude |
| 746 |
Enter the longitude coordinates that describe the device location. |
| 747 |
.4f |
| 748 |
° |
| 749 |
Latitude |
| 750 |
Enter the latitude coordinates that describe the device location. |
| 751 |
Altitude |
| 752 |
Enter the altitude data that describe the device location. |
| 753 |
m |
| 754 |
Location method |
| 755 |
Select the data format for specifying the geographic location. |
| 756 |
No fix |
| 757 |
GPS or Standard Positioning Service fix |
| 758 |
Differential GPS fix |
| 759 |
Precise positioning service (PPS) fix |
| 760 |
Real Time Kinetic (RTK) fixed solution |
| 761 |
Real Time Kinetic (RTK) float solution |
| 762 |
Estimated dead reckoning |
| 763 |
Manual input mode |
| 764 |
Simulation Mode |
| 765 |
None |
| 766 |
Status Bit Not Supported |
| 767 |
No Effect |
| 768 |
Maintenance Required |
| 769 |
Failure |
| 770 |
Out of Specification |
| 771 |
Function Check |
| 772 |
Used to map a status condition to a severity level. |
| 773 |
PV Analog Channel Saturated |
| 774 |
PV Analog Channel Fixed |
| 775 |
047-Sensor limit reached-Sensor 1 |
| 776 |
047-Sensor limit reached-Device temperature |
| 777 |
047-Sensor limit reached-Sensor RJ |
| 778 |
145-Compensation refrence point-Sensor 1 |
| 779 |
201-Electronics faulty-Sensor 1 |
| 780 |
201-Electronics faulty-Device temperature |
| 781 |
201-Electronics faulty-Sensor RJ |
| 782 |
221-Reference sensor defective-Sensor RJ |
| 783 |
402-Initialization active-Sensor 1 |
| 784 |
402-Initialization active-Device temperature |
| 785 |
402-Initialization active-Sensor RJ |
| 786 |
435-Linearization faulty-Sensor 1 |
| 787 |
435-Linearization faulty-Sensor RJ |
| 788 |
485-Process variable simulation active-Sensor 1 |
| 789 |
485-Process variable simulation active-Device temperature |
| 790 |
491-Output simulation-Current output |
| 791 |
531-Factory adjustment missing-Sensor 1 |
| 792 |
531-Factory adjustment missing-Current output |
| 793 |
537-Configuration-Sensor 1 |
| 794 |
537-Configuration-Current output |
| 795 |
Critical Power Failure |
| 796 |
Simulation active |
| 797 |
Non-Volatile memory failure |
| 798 |
Volatile memory error |
| 799 |
Watchdog reset executed |
| 800 |
Power supply conditions out of range |
| 801 |
Environmental conditions out of range |
| 802 |
Electronic failure |
| 803 |
Device configuration locked |
| 804 |
Status Simulation Active |
| 805 |
Discrete Variable Simulation Active |
| 806 |
Event Notification Overflow |
| 807 |
Secondary Analog Channel Saturated |
| 808 |
Tertiary Analog Channel Saturated |
| 809 |
Quaternary Analog Channel Saturated |
| 810 |
Quinary Analog Channel Saturated |
| 811 |
Subdevice list changed |
| 812 |
Duplicate master detected |
| 813 |
Sub-device mismatch |
| 814 |
Sub-devices with duplicate IDs found |
| 815 |
Stale data notice |
| 816 |
Capacity Denied |
| 817 |
Bandwidth allocation pending |
| 818 |
Block transfer pending |
| 819 |
Radio failure |
| 820 |
Secondary Analog Channel Fixed |
| 821 |
Tertiary Analog Channel Fixed |
| 822 |
Quaternary Analog Channel Fixed |
| 823 |
Quinary Analog Channel Fixed |
| 824 |
DiagBehaviour_PrimaryVariableOutOfLimits |
| 825 |
|
| 826 |
DiagBehaviour_NonPrimaryVariableOutOfLimits |
| 827 |
DiagBehaviour_LoopCurrentSaturated |
| 828 |
DiagBehaviour_LoopCurrentFixed |
| 829 |
DiagBehaviour_MoreStatusAvailable |
| 830 |
DiagBehaviour_ColdStart |
| 831 |
DiagBehaviour_ConfigurationChanged |
| 832 |
DiagBehaviour_DeviceMalfunction |
| 833 |
Alarm |
| 834 |
Warning |
| 835 |
DiagBehaviour_NotUsed59 |
| 836 |
DiagBehaviour_NotUsed60 |
| 837 |
DiagBehaviour_NotUsed61 |
| 838 |
DiagBehaviour_NotUsed62 |
| 839 |
DiagBehaviour_NotUsed63 |
| 840 |
DiagBehaviour_NotUsed64 |
| 841 |
DiagBehaviour_NotUsed65 |
| 842 |
DiagBehaviour_NotUsed66 |
| 843 |
DiagBehaviour_NotUsed67 |
| 844 |
DiagBehaviour_NotUsed68 |
| 845 |
DiagBehaviour_NotUsed69 |
| 846 |
DiagBehaviour_NotUsed70 |
| 847 |
DiagBehaviour_MaintenanceRequired |
| 848 |
DiagBehaviour_DeviceVariableAlert |
| 849 |
DiagBehaviour_CriticalPowerFailure |
| 850 |
DiagBehaviour_Failure |
| 851 |
DiagBehaviour_OutOfSpecification |
| 852 |
DiagBehaviour_FunctionCheck |
| 853 |
DiagBehaviour_NotUsed1 |
| 854 |
DiagBehaviour_NotUsed2 |
| 855 |
DiagBehaviour_DeviceOperatingMode1 |
| 856 |
DiagBehaviour_DeviceOperatingMode2 |
| 857 |
DiagBehaviour_DeviceOperatingMode3 |
| 858 |
DiagBehaviour_DeviceOperatingMode4 |
| 859 |
DiagBehaviour_DeviceOperatingMode5 |
| 860 |
DiagBehaviour_DeviceOperatingMode6 |
| 861 |
DiagBehaviour_DeviceOperatingMode7 |
| 862 |
DiagBehaviour_DeviceOperatingMode8 |
| 863 |
DiagBehaviour_DeviceVariableSimulationActive |
| 864 |
DiagBehaviour_NonVolatileMemoryDefect |
| 865 |
DiagBehaviour_VolatileMemoryDefect |
| 866 |
DiagBehaviour_WatchdogResetExecuted |
| 867 |
DiagBehaviour_PowerSupplyConditionsOutOfRange |
| 868 |
DiagBehaviour_EnvironmentalConditionsOutOfRange |
| 869 |
DiagBehaviour_ElectronicDefect |
| 870 |
DiagBehaviour_DeviceConfigurationLocked |
| 871 |
DiagBehaviour_StatusSimulationActive_ |
| 872 |
DiagBehaviour_DiscreteVariableSimulationActive |
| 873 |
DiagBehaviour_EventNotificationOverflow |
| 874 |
DiagBehaviour_BatteryOfPowerSupplyNeedsMaintenance |
| 875 |
DiagBehaviour_NotUsed4 |
| 876 |
DiagBehaviour_NotUsed5 |
| 877 |
DiagBehaviour_NotUsed6 |
| 878 |
DiagBehaviour_NotUsed7 |
| 879 |
DiagBehaviour_AnalogChannel1Saturated |
| 880 |
DiagBehaviour_AnalogChannel2Saturated |
| 881 |
DiagBehaviour_AnalogChannel3Saturated |
| 882 |
DiagBehaviour_AnalogChannel4Saturated |
| 883 |
DiagBehaviour_NotUsed8 |
| 884 |
DiagBehaviour_NotUsed9 |
| 885 |
DiagBehaviour_NotUsed10 |
| 886 |
DiagBehaviour_NotUsed11 |
| 887 |
DiagBehaviour_SubDeviceListChanged |
| 888 |
DiagBehaviour_DuplicateMasterDetected |
| 889 |
DiagBehaviour_SubDeviceMismatch |
| 890 |
DiagBehaviour_SubDeviceWithDuplicateIdsFound |
| 891 |
DiagBehaviour_StateDataNotice |
| 892 |
DiagBehaviour_NotUsed12 |
| 893 |
DiagBehaviour_NotUsed13 |
| 894 |
DiagBehaviour_NotUsed14 |
| 895 |
DiagBehaviour_CapacityDenied |
| 896 |
DiagBehaviour_NotUsed15 |
| 897 |
DiagBehaviour_BandwidthAllocationPending |
| 898 |
DiagBehaviour_BlockTransferPending |
| 899 |
DiagBehaviour_RadioFailure |
| 900 |
DiagBehaviour_NotUsed16 |
| 901 |
DiagBehaviour_NotUsed17 |
| 902 |
DiagBehaviour_NotUsed18 |
| 903 |
DiagBehaviour_AnalogChannel1Fixed |
| 904 |
DiagBehaviour_AnalogChannel2Fixed |
| 905 |
DiagBehaviour_AnalogChannel3Fixed |
| 906 |
DiagBehaviour_AnalogChannel4Fixed |
| 907 |
DiagBehaviour_NotUsed19 |
| 908 |
DiagBehaviour_NotUsed20 |
| 909 |
DiagBehaviour_NotUsed21 |
| 910 |
DiagBehaviour_NotUsed22 |
| 911 |
Squawk off |
| 912 |
Squawk on |
| 913 |
Squawk once |
| 914 |
Change user role |
| 915 |
Change user role |
| 916 |
|
| 917 |
Define password |
| 918 |
Logout |
| 919 |
Delete password |
| 920 |
Change password |
| 921 |
Change password |
| 922 |
Reset Password |
| 923 |
Reset sensor min/max values |
| 924 |
Reset min/max values of the sensor value. |
| 925 |
Reset min/max- values of electronic temperature to their default values. |
| 926 |
Reset configuration changed flag |
| 927 |
Page_Number_Validity |
| 928 |
Max_Number_of_Pages |
| 929 |
Cancel |
| 930 |
Finish |
| 931 |
Previous |
| 932 |
Next |
| 933 |
Graphical mode |
| 934 |
simple |
| 935 |
graphical |
| 936 |
Commissioning |
| 937 |
Commissioning wizard |
| 938 |
This wizard guides you through the commissioning procedure for the device. |
| 939 |
Password delete |
| 940 |
Password wizard |
| 941 |
Choose password action |
| 942 |
Delete Password |
| 943 |
Recover Password |
| 944 |
Enter password |
| 945 |
Commissioning wizard |
| 946 |
Abort |
| 947 |
Device management |
| 948 |
Sensor |
| 949 |
Output current |
| 950 |
User management |
| 951 |
Details |
| 952 |
Details 1 |
| 953 |
LocalDiagnostics |
| 954 |
Diagnostics |
| 955 |
Details 2 |
| 956 |
Details 3 |
| 957 |
Details 4 |
| 958 |
Details 5 |
| 959 |
Details 6 |
| 960 |
Details 7 |
| 961 |
Details 8 |
| 962 |
Details 9 |
| 963 |
Details 10 |
| 964 |
Remedy |
| 965 |
Remedy information:
1. Restart device
2. Replace electronics
|
| 966 |
Remedy information:
Increase supply voltage
|
| 967 |
Remedy information:
1. Contact service organization
2. Replace device
|
| 968 |
Remedy information:
1. Check process value
2. Check application
3. Check sensor
|
| 969 |
Remedy information:
1. Check ambient temperature
2. Check process temperature
|
| 970 |
Remedy information:
1. Check connection
2. Repeat data transfer
|
| 971 |
Remedy information:
1. Check device configuration
2. Up- and download new configuration
|
| 972 |
Remedy information:
Check current output configuration
|
| 973 |
Remedy information:
Check linearization
|
| 974 |
Remedy information:
Replace device
|
| 975 |
Remedy information:
1. Check electrical connection
2. Replace sensor 1
3. Check connection type
|
| 976 |
Remedy information:
1. Check electrical connection
2. Check sensor
3. Replace sensor or cable
|
| 977 |
Remedy information:
1. Check sensor
2. Replace sensor
|
| 978 |
Remedy information:
1. Check terminal temperature
2. Check external reference point
|
| 979 |
Remedy information:
1. Check sensor
2. Check process conditions
|
| 980 |
Remedy information:
Up-/download in progress, please wait
|
| 981 |
Remedy information:
Switch on diagnostics for thermocouple measurement
|
| 982 |
Remedy information:
Deactivate simulation
|
| 983 |
Remedy information:
Factory reset in progress, please wait
|
| 984 |
Remedy information:
Initialization in progress, please wait
|
| 985 |
No remedy defined |
| 986 |
Starting Status Map Index must be even value. |
| 987 |
iTEMP TMT72 |
| 988 |
Guidance |
| 989 |
Application |
| 990 |
System |
| 991 |
Measured values |
| 992 |
HART configuration |
| 993 |
Actual diagnostics |
| 994 |
Diagnostic list |
| 995 |
Event logbook |
| 996 |
Simulation |
| 997 |
Diagnostic settings |
| 998 |
Min/max values |
| 999 |
Bluetooth configuration |
| 1000 |
Information |
| 1001 |
Display |
| 1002 |
Linearization |
| 1003 |
Properties |
| 1004 |
Diagnostic behaviour |
| 1005 |
Status signal |
| 1006 |
Electronics |
| 1007 |
Configuration |
| 1008 |
Process |
| 1009 |
Device |
| 1010 |
HART info |
| 1011 |
Device location |
| 1012 |
Setup |
| 1013 |
maintenance_root_menu |
| 1014 |
not supported |
| 1015 |
Commissioning |
| 1016 |
The commissioning for this device has not yet taken place. It is recommended to use the commissioning wizard. |
| 1017 |
Reset password |
| 1018 |
Diagnostics event |
| 1019 |
Squawk |
| 1020 |
Device overview |
| 1021 |
Device information |
| 1022 |
Change access |
| 1023 |
Locking state |
| 1024 |
Chart monitor |
| 1025 |
Manufacturer Logo |
| 1026 |
HartLogo |
| 1027 |
Device icon |
| 1028 |
ProgressBar0of4 |
| 1029 |
ProgressBar1of4 |
| 1030 |
ProgressBar2of4 |
| 1031 |
ProgressBar3of4 |
| 1032 |
ProgressBar4of4 |
| 1033 |
ProgressBar4Ready |
| 1034 |
Device status |
| 1035 |
Status byte 0 |
| 1036 |
Status byte 1 |
| 1037 |
Status byte 2 |
| 1038 |
Status byte 3 |
| 1039 |
Status byte 4 |
| 1040 |
Extended Device Status |
| 1041 |
Device standardized status 0 |
| 1042 |
Device standardized status 1 |
| 1043 |
Device standardized status 2 |
| 1044 |
Device standardized status 3 |
| 1045 |
HART diagnostics |
| 1046 |
iTEMP TMT72 Offline |
| 1047 |
Failure |
| 1048 |
Out of specification |
| 1049 |
Function check |
| 1050 |
Device configuration locked |
| 1051 |
Discrete variable simulation active |
| 1052 |
Event notification overflow |
| 1053 |
Battery of power supply needs maintenance |
| 1054 |
Sub-devices with duplicated ids found |
| 1055 |
1. Check electrical connection
2. Replace sensor 1
3. Check connection type |
| 1056 |
1. Check sensor
2. Replace sensor |
| 1057 |
1. Check electrical connection
2. Check sensor
3. Replace sensor or cable |
| 1058 |
1. Check sensor
2. Check process conditions |
| 1059 |
1. Check terminal temperature
2. Check external reference point |
| 1060 |
1. Restart device
2. Replace electronics |
| 1061 |
Replace device |
| 1062 |
Factory reset in progress, please wait |
| 1063 |
Initialization in progress, please wait |
| 1064 |
1. Check connection
2. Repeat data transfer |
| 1065 |
Up-/download in progress, please wait |
| 1066 |
Check linearization |
| 1067 |
Deactivate simulation |
| 1068 |
1. Contact service organization
2. Replace device |
| 1069 |
1. Check device configuration
2. Up- and download new configuration |
| 1070 |
Check current output configuration |
| 1071 |
Switch on diagnostics for thermocouple measurement |
| 1072 |
Increase supply voltage |
| 1073 |
1. Check ambient temperature
2. Check process temperature |
| 1074 |
1. Check process value
2. Check application
3. Check sensor |
| 1075 |
Squawk Control |
| 1076 |
Squawk Control- Codes to to enable/disable squawk mechanism |
| 1077 |
Squawk Once |
| 1078 |
Upload variables |
| 1079 |
Loop Warning Variables |
| 1080 |
Loop Warning Variables - Variables that display a warning message before new values are sent. |
| 1081 |
PV |
| 1082 |
SV |
| 1083 |
TV |
| 1084 |
QV |
| 1085 |
SV value |
| 1086 |
TV value |
| 1087 |
QV value |
| 1088 |
PV unit |
| 1089 |
SV unit |
| 1090 |
TV unit |
| 1091 |
QV unit |
| 1092 |
PV status |
| 1093 |
SV status |
| 1094 |
TV status |
| 1095 |
QV status |
| 1096 |
PV classification |
| 1097 |
SV classification |
| 1098 |
TV classification |
| 1099 |
QV classification |
| 1100 |
PV upper limit |
| 1101 |
SV upper limit |
| 1102 |
TV upper limit |
| 1103 |
QV upper limit |
| 1104 |
PV lower limit |
| 1105 |
SV lower limit |
| 1106 |
TV lower limit |
| 1107 |
QV lower limit |
| 1108 |
pv_min_span |
| 1109 |
pv_damping |
| 1110 |
7d |
| 1111 |
Wireless |
| 1112 |
WirelessHART Device |
| 1113 |
IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation |
| 1114 |
Primary |
| 1115 |
Primary Analog Channel |
| 1116 |
Secondary |
| 1117 |
Secondary Analog Channel |
| 1118 |
Tertiary |
| 1119 |
Tertiary Analog Channel |
| 1120 |
Quaternary |
| 1121 |
Quaternary Analog Channel |
| 1122 |
Quinary |
| 1123 |
Quinary Analog Channel |
| 1124 |
Lock all |
| 1125 |
Trim not supported |
| 1126 |
Configuration cannot be changed |
| 1127 |
Locked by gateway |
| 1128 |
Analog Input Channel |
| 1129 |
Analog Output Channel |
| 1130 |
The device is in simulation mode and the level output is not representative of the process. |
| 1131 |
The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed. |
| 1132 |
The RAM memory check is invalid or maybe corrupt |
| 1133 |
A watchdog reset has been performed |
| 1134 |
Voltage conditions out of range |
| 1135 |
A voltage condition is outside its allowable range |
| 1136 |
An internal or environmental condition is beyond acceptable limits. |
| 1137 |
A hardware problem not related to the sensor has been detected. |
| 1138 |
The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified |
| 1139 |
Battery life |
| 1140 |
Percent range |
| 1141 |
Loop current |
| 1142 |
Primary variable |
| 1143 |
Secondary variable |
| 1144 |
Tertiary variable |
| 1145 |
Quaternary variable |
| 1146 |
Read receive time |
| 1147 |
Write date and time |
| 1148 |
Non-Volatile Clock |
| 1149 |
When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure. |
| 1150 |
Clock Uninitialized |
| 1151 |
The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device. |
| 1152 |
No restrictions |
| 1153 |
SI Only |
| 1154 |
Restricted to SI Unit codes only |
| 1155 |
Process automation device |
| 1156 |
Discrete device |
| 1157 |
Hybrid:Process automation+discrete |
| 1158 |
I/O System |
| 1159 |
WirelessHART Process automation device |
| 1160 |
WirelessHART Discrete device |
| 1161 |
WirelessHART Process automation+discrete |
| 1162 |
WirelessHART Gateway |
| 1163 |
WirelessHART Access point |
| 1164 |
WirelessHART Process adapter |
| 1165 |
WirelessHART Discrete adapter |
| 1166 |
WirelessHART enabled handheld/portable maintenance tool |
| 1167 |
Device Profile |
| 1168 |
US |
| 1169 |
United States of America |
| 1170 |
JP |
| 1171 |
Japan |
| 1172 |
DE |
| 1173 |
Germany |
| 1174 |
FR |
| 1175 |
France |
| 1176 |
ES |
| 1177 |
Spain |
| 1178 |
RU |
| 1179 |
Russian Federation |
| 1180 |
CN |
| 1181 |
People's Republic of China |
| 1182 |
Secondary Master |
| 1183 |
Primary Master |
| 1184 |
Device Diagnostic Status 0 |
| 1185 |
Device Diagnostic Status 1 |
| 1186 |
I/O and Subdevice Status |
| 1187 |
WirelessHART Status |
| 1188 |
Time Set Option |
| 1189 |
Real Time Clock Flags |
| 1190 |
Country |
| 1191 |
Country of intended device installation |
| 1192 |
SI Unit Control |
| 1193 |
Indicates if device should only display SI unit codes |
| 1194 |
Enable on token-passing data link layer only |
| 1195 |
Enable on TDMA data link layer only |
| 1196 |
Enable on both TDMA and token-passing data link layer |
| 1197 |
Time Stamp |
| 1198 |
Relative time value on network |
| 1199 |
8u |
| 1200 |
Dynamic Variables Returned for Device Variables |
| 1201 |
Configuration Change Counter Mismatch |
| 1202 |
Status bytes mismatch |
| 1203 |
count |
| 1204 |
8.3f |
| 1205 |
Send |
| 1206 |
navigationSelection |
| 1207 |
Back;Finish |
| 1208 |
Finish |
| 1209 |
DeletePW |
| 1210 |
Next>;Send |
| 1211 |
<Back;Send;Finish |
| 1212 |
<Back;Finish |
| 1213 |
Next>;Cancel |
| 1214 |
<Back;Next>;Cancel |
| 1215 |
<Back;Finish;Cancel |
| 1216 |
0 |