Device dictionary

Loading…

Reference ID	String
0	TMD832
1	Set to nearest possible value
2	Invalid value selection
3	.2f
4	Error code
5	Diagnostic Code that has Field Device status information relating to failure/warning.
6	ERR./WARN.Nø000 - No error(s) or warning(s) detected
7	ERR.Nø011 - Hardware error
8	ERR.Nø012 - Alarm: overflow - Input signal too high
9	ERR.Nø013 - Alarm: overflow - Input signal too low
10	WARN.Nø201 - Alarm: overflow - Measured value too high
11	WARN.Nø202 - Alarm: overflow - Measured value too low
12	WARN.Nø203 - Up/Down-load active
13	WARN.Nø204 - Default active
14	deg.C
15	deg.F
16	mV
17	ohm
18	sec
19
20	AO
21	.3f
22	Output value
23	.1f
24	Sensor input
25	Lists the type of sensor supported. For user selection.
26	80 mV FS
27	400 ohms FS
28	4000 ohms FS
29	Pt 100
30	Ni 100
31	Pt 1000
32	Tc B
33	Tc C
34	Tc D
35	Tc E
36	Tc J
37	Tc K
38	Tc L
39	Tc N
40	Tc R
41	Tc S
42	Tc T
43	Tc U
44	Select mV
45	Select 400
46	Select 4000
47	Select page
48	PV Value
49	Temp. compensation
50	For TC only. Temperature Compensation Measured Value used for cold junction reference point compensation, if INTERNAL is selected.
51	Input filter
52	Filter Value - Damping time constant applied to both the Digital Value representetion and Analog Value of the respective Analog Output. The units of this variable are always in seconds.
53	2.0f
54	6.0f
55	RJ mode
56	For TC input only. Ambient temperature compensation existing at cold junction point is normally provided by an 'INTERNAL' measuring sensor. However the user may choose to set this temp. compensation value as an 'EXTERNAL'fixed parameters.
57	INTERNAL
58	EXTERNAL
59	RJ external value
60	If the has selected to choose the external compensation functionality, then a corresponding value must be inserted in this location. Value may range from -50 to +94.
61	6.2f
62	Bias input 1
63	Offset added to the input signal to compensate for installation where the sensor cannot be placed exactly where the measurementis needed, or to correct for drifts. Value may range from -10.0 to +10.0.
64	Measuring unit
65	Dir./rev. action
66	The output signal can have a direct action (increases when the process variable increases) or reverse action (increases when the process variable decreases). For user selection.
67	Dir. action
68	Rev. action
69	Value for 4 mA
70	7.2f
71	Value for 20 mA
72	R/RTD connection
73	For RTD input only. Lists the type of sensor connection supprted. For user selection.
74	2 wire
75	3 wire
76	4 wire
77	R/RTD 2 wire comp.
78	For 2 wire R or RTD input only. The value to be inserted is the resistence of the connection wires, expressed in ohm. Value may range from 0 to 30.
79	Sensor error
80	When the transmitter detects a failure output signal is forced to a predefined value. For user selection: LOW=down_scale, HIGH=up_scale.
81	Low
82	High
83	Last diagnostic
84	Last detected diagnostic code.
85	Default values
86	Matrix parameters reset function default of transmitter data according to the manual.
87	Tag number
88	Software version
89	Information related to the instrument software version, assigned by the Factory for traceability purposes.
90	Modification n.
91	Information related to the complete instrument - hardware and software - version, assigned by the Factory for traceability purposes.
92	Serial number
93	Instrument serial number assigned by the Factory for traceability purposes.
94	Filter
95	AO
96	D/R
97	Err
98	fnctn
99	20
100	4
101	span
102	T. comp.
103	RJ unit
104	mode
105	Ext val.
106	PV variables
107	PV sensor
108	OFFLINE
109	Matrix parameters
110	Working parameters
111	Calibration Chan.1
112	Output calibration
113	Service
114
115	FMU860
116	DT
117	DVC
118	FCX
119	AS800
120	340T
121	340C
122	344
123	Siemens Micro K
124	SITRANS L
125	SIPAN PH
126	SITRANS P
127	75SMT
128	UNIDELTA
129	8320
130	SX5100
131	TSV175
132	DMU
133	3780
134	BM70
135	8u
Reference ID	String