Device dictionary

Loading…

Reference ID	String
0	6u
1	PROWIRL77
2	ERROR 101: Sensor defective
3	ERROR 102: EE-Prom Hardware Error
4	ERROR 102: EE-Prom Checksum Error
5	ERROR 103: Com. Error - Communication Error with Pre-amplifier
6	WARNING 205: Current output simulation active
7	WARNING 203: Current out of range
8	.7g
9	8.7g
10	.2f
11	Flow unit
12	m3/s
13	m3/min
14	m3/h
15	ACF/s
16	ACF/min
17	ACF/h
18	usg/s
19	usg/min
20	usg/h
21	user
22	Tot. unit
23	Totalizer Unit- Engineering units that the totalizer will be displayed with.
24	m3
25	ACF
26	usg
27	PV Damping
28	.1f
29	5.1f
30	Status: normal
31	Status: err/warn
32	Frequency unit
33
34	unit_0
35	VF
36	Vortex Frequency - Vortex frequency measured with sensor
37	Tot
38	Totalizer - Totalized Flow
39	Flow user unit
40	Flow user unit - User defined conversion factor to convert flow values from dm3/s into another unit
41	.4g
42	8.4g
43	Tot. user unit
44	Tot. user unit - User defined conversion factor to convert volume values from dm3 into another unit
45	AO Alarm type
46	Display mode
47	Display mode - Defines the parameter which will be displayed on the local LC-display
48	Percent
49	Flow rate
50	Totalizer
51	Totalizer ovl
52	Customer Code
53	Customer Code - Safety code for local access and write protect for HART.
54	4d
55	Code entry
56	Safety code entry field for local access and write protect for HART. Entering correct code disables write protection, entering -1 enables write protection.
57	Software Version
58	SW mainboard - Software version of mainboard
59	Hardware Version
60	HV mainboard - Hardware version of mainboard
61	Fluid
62	Define application: gas/steam or liquid
63	Liquid
64	Gas/Steam
65	DN
66	DN - Defines the nominal diameter of the pipe
67	15 (.5 in)
68	25 (1 in)
69	40 (1.5 in)
70	50 (2 in)
71	80 (3 in)
72	100 (4 in)
73	150 (6 in)
74	200 (8 in)
75	250 (10 in)
76	300 (12 in)
77	K-factor
78	K-factor - Calibration factor
79	Body expan. coeff
80	e-5/K
81	Body expan. coeff. - Coefficient is used in conjunction with the average process temperature to correct thermal expansion effects of the meter body
82	.3f
83	5.3f
84	Ave. process temp
85	Ave. process temp - Defines the average process temperature
86	K
87	.0f
88	3.0f
89	Ampl. Gain
90	Ampl. Gain - Amplifier gain
91	very low
92	low
93	normal
94	high
95	Var. Number
96	Flow Sensor- Hardware that measures flow rate.
97	Flow Sensor - Hardware that measures flow rate.
98	Note to the operator that this information must be sent before further editing.
99	Edit Notice
100	Code entry
101	Safety code entry field for write protect for HART. Entering correct code disables write protection, entering -1 enables write protection.
102	Reset Totalizer
103	Reset Totalizer - Resets the totalizer and the overflow counter for totalizer.
104	Offline
105	Matrix group sel.
106	System Units
107	Analog Output
108	Display
109	System Parameters
110	Sensor Data
111	Device Data
112	Review
113	write variables
114	FMU860
115	DT
116	DVC
117	FCX
118	AS800
119	340T
120	340C
121	344
122	Siemens Micro K
123	SITRANS L
124	SIPAN PH
125	SITRANS P
126	75SMT
127	UNIDELTA
128	8320
129	SX5100
130	TSV175
131	DMU
132	3780
133	BM70
134	8u
135	Pulse Output Unit- Engineering units that the frequency andtotalizer outputs will be displayed with.
136	6.2f
137	4.2f
138	7d
139	HART Output
140	Status
141	Revision #'s
142	NOTICE - This information must be sent to the transmitter to update dependent parameters.
143	About to perform Totalizer Reset!
144	Totalizer reset performed
Reference ID	String