Device dictionary

Loading…

Reference ID	String
0	6u
1	PROWIRL70
2	ERROR 101: Sensor defective
3	ERROR 102: Checksum Error - Internal EE-Prom Error
4	ERROR 103: Com. Error - Communication Error with Preamplifier
5	WARNING 201: DAT Error - No DAT found
6	WARNING 202: DAT Error - Checksum Error
7	WARNING 203: Current out of range
8	WARNING 204: Output frequency out of range
9	Pulse scaling
10	12.5f
11	.2f
12	Flow unit
13	m3/s
14	m3/min
15	m3/h
16	ACF/s
17	ACF/min
18	ACF/h
19	usg/s
20	usg/min
21	usg/h
22	user
23	Tot. unit
24	Pulse Output Unit- Engineering units that the frequency and totalizer outputs will be displayed with.
25	m3
26	ACF
27	usg
28	PV Damping
29	.1f
30	5.1f
31	Status: normal
32	Status: err/warn
33	Frequency unit
34
35	unit_0
36	VF
37	Vortex Frequency - Vortex frequency measured with sensor
38	FO
39	Output Frequency - Digital representation of the output frequency
40	.3f
41	Tot
42	Totalizer - Totalized Flow
43	Flow unit mantis.
44	Flow unit mantis. - Defines mantissa of conversion factor to convert flow values from dm3/s into another unit
45	Flow unit expon.
46	Flow unit expon. - Defines exponent of conversion factor to convert flow values from dm3/s into another unit
47	3d
48	Tot. unit mantis.
49	Tot. unit mantis. - Defines mantissa of conversion factor to convert volume values from dm3 into another unit
50	Tot. unit expon.
51	Tot. unit expon. - Defines exponent of conversion factor to convert volume values from dm3 into another unit
52	AO Alarm type
53	Open coll. func.
54	Defines function of the open collector output
55	Frequency output
56	Alarm active on
57	Alarm active off
58	Limit Switch
59	Limit switch on
60	Limit switch on - flow value for switching on the limit switch
61	Limit switch off
62	Limit switch off - flow value for switching off the limit switch
63	Display mode
64	Display mode - Defines the parameter which will be displayed on the local LC-display
65	Percent
66	Flow rate
67	Totalizer
68	Totalizer ovl
69	Customer Code
70	Customer Code - Safety code for local access and write protect for HART.
71	4d
72	Code Entry
73	Safety code entry field for local access and write protect for HART. Entering correct code disables write protection, entering -1 enables write protection.
74	SW mainboard
75	SW mainboard - Software version of mainboard
76	SW preamplifier
77	SW preamplifier - Software version of preamplifier
78	HW mainboard
79	HV mainboard - Hardware version of mainboard
80	Fluid
81	Define application: gas/steam or liquid
82	Liquid
83	Gas/Steam
84	DN
85	DN - Defines the nominal diameter of the pipe
86	15 (.5 in)
87	25 (1 in)
88	40 (1.5 in)
89	50 (2 in)
90	80 (3 in)
91	100 (4 in)
92	150 (6 in)
93	200 (8 in)
94	250 (10 in)
95	300 (12 in)
96	other
97	K-factor
98	K-factor - Calibration factor
99	8.4f
100	Body expan. coeff
101	1/K
102	Body expan. coeff. - Coefficient is used in conjunction with the average process temperature to correct thermal expansion effects of the meter body
103	5.2f
104	Ave. process temp
105	Ave. process temp - Defines the average process temperature
106	K
107	6.2f
108	Ampl. Gain
109	Ampl. Gain - Amplifier gain
110	very low
111	low
112	normal
113	high
114	Var. Number
115	Flow Sensor- Hardware that measures flow rate.
116	Pulse output- scaled frequency output from 0-100 Hz.
117	Flow Sensor - Hardware that measures flow rate.
118	Pulse Output- Scaled frequency output from 0-100 Hz
119	Pulse output units- Engineering units that the frequency and totalizer outputs will be displayed with
120	Totalized volume
121	Note to the operator that this information must be sent before further editing.
122	Edit Notice
123	Leave frequency simulation
124	Abort frequency simulation
125	Freq. simulation
126	Freq. simulation - Allows the user to manually manipulate the frequency output to a selected constant output value.
127	Code entry
128	Safety code entry field for write protect for HART. Entering correct code disables write protection, entering -1 enables write protection.
129	Reset Totalizer
130	Reset Totalizer - Resets the totalizer and the overflow counter for totalizer.
131	Offline
132	Matrix group sel.
133	System Units
134	Analog Output
135	Open Collector
136	Display
137	System Parameters
138	Sensor Data
139	Device Data
140	Review
141	write variables
142	FMU860
143	DT
144	DVC
145	FCX
146	AS800
147	340T
148	340C
149	344
150	Siemens Micro K
151	SITRANS L
152	SIPAN PH
153	SITRANS P
154	75SMT
155	UNIDELTA
156	8320
157	SX5100
158	TSV175
159	DMU
160	3780
161	BM70
162	8u
163	low
164	high
165	tmp_av
166	Pulse Output Unit- Engineering units that the frequency andtotalizer outputs will be displayed with.
167	4.2f
168	7d
169	Pulse Scaling Factor- Magnitude of process variable per pulse.
170	7.5f
171	.5f
172	HART Output
173	Status
174	Revision #'s
175	NOTICE - This information must be sent to the transmitter to update dependent parameters.
176	About to leave frequency simulation mode!
177	About to perform output frequency test!
178	Choose output frequency
179	1 Hz; 50 Hz;100 Hz;other;end
180	Enter frequency
181	The output frequency is fixed at %{0} Hz
182	About to perform Totalizer Reset!
183	Totalizer reset performed
Reference ID	String