| 0 |
PROMASS63 |
| 1 |
System error amplifier: Low voltage detected |
| 2 |
Tubes not oscillating |
| 3 |
System error amplifier: DAT failure |
| 4 |
System error amplifier :EEPROM failure |
| 5 |
System error amplifier: RAM failure |
| 6 |
PICK-UP failure |
| 7 |
System error amplifier: EC_AMPLIFIER set |
| 8 |
System error amplifier: Temp. circuit failure |
| 9 |
System error amplifier: ASIC failure |
| 10 |
System error amplifier: Temperature sensor measuring tubes |
| 11 |
System error amplifier: Temperature sensor carrier tube |
| 12 |
System error amplifier: EC_IOUT_CAL_DATA set |
| 13 |
No amplifier response |
| 14 |
Value not accepted |
| 15 |
System error COM-Module: EEPROM failure |
| 16 |
System error COM-Module: RAM failure |
| 17 |
System error COM-Module: ROM failure |
| 18 |
System error COM-Module: Low voltage detected |
| 19 |
System error COM-Module: Voltage reference |
| 20 |
System error COM-Module: EEPROM HW data error |
| 21 |
System error COM-Module: EEPROM parameter data error |
| 22 |
System error COM-Module:EEPROM totalisator data error |
| 23 |
|
| 24 |
System error amplifier: Software version incompatible |
| 25 |
System error amplifier: Hardware version incompatble |
| 26 |
System error amplifier: Software typ changed |
| 27 |
System error COM-Module: EEPROM default values |
| 28 |
System error COM-Module: Hardware typ incompatible |
| 29 |
System error COM-Module: Hardware version incompatible |
| 30 |
System error COM-Module: Software typ changed |
| 31 |
System error COM-Module: Software downgrade not possible |
| 32 |
System error power-supply: Low voltage detected |
| 33 |
System warning amplifier: WC_SENSOR_DEFAULT_PRO_PARAM set |
| 34 |
DAT contains default daten |
| 35 |
Excite. current limt |
| 36 |
Slug flow conditions |
| 37 |
Empty pipe |
| 38 |
Flow to high |
| 39 |
Zero adjust not possible |
| 40 |
System warning amplifier: WC_PULSE_OVERFLOW set |
| 41 |
System warning amplifier: WC_CURRENT_OVERFLOW set |
| 42 |
Current output overflow |
| 43 |
Current output 2 overflow |
| 44 |
Frequency output overflow |
| 45 |
Density adjust failure |
| 46 |
Batch time exceeded |
| 47 |
Positive zero return active |
| 48 |
Frequence output output simulation active |
| 49 |
Batching is running |
| 50 |
Original calibration data not possible |
| 51 |
Current output 1 simulation active |
| 52 |
Current output 2 simulation acitve |
| 53 |
Assign output |
| 54 |
Assign line 1 |
| 55 |
Assign line 2 |
| 56 |
Status: normal |
| 57 |
Status: errors |
| 58 |
Low flow cutoff |
| 59 |
.4f |
| 60 |
Serial number |
| 61 |
INVALID VALUE SELECTION |
| 62 |
Flow |
| 63 |
Mass |
| 64 |
Volume flow |
| 65 |
Volume |
| 66 |
Std.volume flow |
| 67 |
Target flow |
| 68 |
Carrier flow |
| 69 |
Dens. |
| 70 |
calc. Density |
| 71 |
Temp. |
| 72 |
.1f |
| 73 |
Tot.1 > |
| 74 |
Tot.1 |
| 75 |
12.4f |
| 76 |
e7 gal |
| 77 |
e7 l |
| 78 |
e7 m3 |
| 79 |
e7 bbl |
| 80 |
e7 g |
| 81 |
e7 kg |
| 82 |
e7 t |
| 83 |
e7 lb |
| 84 |
e7 ton |
| 85 |
e7 Nm3 |
| 86 |
e7 Nl |
| 87 |
e7 dm3 |
| 88 |
e7 cm3 |
| 89 |
e7 scm |
| 90 |
e7 scf |
| 91 |
e7 hl |
| 92 |
e7 cc |
| 93 |
|
| 94 |
Total.1 overflow |
| 95 |
5d |
| 96 |
Totalizer 2 > |
| 97 |
Totalizer 2 |
| 98 |
Total.2 overflow |
| 99 |
Reset totalizer |
| 100 |
cancel |
| 101 |
Totalizer 1 |
| 102 |
Total. 1&2 |
| 103 |
Assign total.1 |
| 104 |
off |
| 105 |
Mass(+) |
| 106 |
Std.volume |
| 107 |
Volume(+) |
| 108 |
Std.volume(+) |
| 109 |
Target material |
| 110 |
Target mat(+) |
| 111 |
Carrier fluid |
| 112 |
Carrier fluid(+) |
| 113 |
Assign total.2 |
| 114 |
Mass(-) |
| 115 |
Volume(-) |
| 116 |
Std.volume(-) |
| 117 |
Target mat(-) |
| 118 |
Carrier fluid(-) |
| 119 |
Mass flow unit |
| 120 |
g/min |
| 121 |
g/h |
| 122 |
kg/s |
| 123 |
kg/min |
| 124 |
kg/h |
| 125 |
t/min |
| 126 |
t/h |
| 127 |
t/d |
| 128 |
lb/s |
| 129 |
lb/min |
| 130 |
lb/hr |
| 131 |
ton/min |
| 132 |
ton/hr |
| 133 |
ton/day |
| 134 |
Mass unit |
| 135 |
g |
| 136 |
kg |
| 137 |
t |
| 138 |
lb |
| 139 |
ton |
| 140 |
Volume flow unit |
| 141 |
cm3/min |
| 142 |
cm3/h |
| 143 |
dm3/s |
| 144 |
dm3/min |
| 145 |
dm3/h |
| 146 |
l/s |
| 147 |
l/min |
| 148 |
l/h |
| 149 |
hl/min |
| 150 |
hl/h |
| 151 |
m3/min |
| 152 |
m3/h |
| 153 |
cc/min |
| 154 |
cc/hr |
| 155 |
gal/min |
| 156 |
gal/hr |
| 157 |
gal/day |
| 158 |
gpm |
| 159 |
gph |
| 160 |
gpd |
| 161 |
mgd |
| 162 |
bbl/min |
| 163 |
bbl/hr |
| 164 |
bbl/day |
| 165 |
Volume unit |
| 166 |
cm3 |
| 167 |
dm3 |
| 168 |
l |
| 169 |
hl |
| 170 |
m3 |
| 171 |
cc |
| 172 |
gal |
| 173 |
bbl |
| 174 |
Gallons/Barrel |
| 175 |
US: 31.0 gal/bbl |
| 176 |
US: 31.5 gal/bbl |
| 177 |
US: 42.0 gal/bbl |
| 178 |
US: 55.0 gal/bbl |
| 179 |
Imp: 36.0 gal/bbl |
| 180 |
Imp: 42.0 gal/bbl |
| 181 |
Stdvol.flow unit |
| 182 |
Nl/s |
| 183 |
Nl/min |
| 184 |
Nl/h |
| 185 |
Nl/d |
| 186 |
Nm3/s |
| 187 |
Nm3/min |
| 188 |
Nm3/h |
| 189 |
Nm3/d |
| 190 |
scm/s |
| 191 |
scm/min |
| 192 |
scm/hr |
| 193 |
scm/day |
| 194 |
scf/s |
| 195 |
scf/min |
| 196 |
scf/hr |
| 197 |
scf/day |
| 198 |
Std.volume unit |
| 199 |
Nm3 |
| 200 |
Nl |
| 201 |
scm |
| 202 |
scf |
| 203 |
Density unit |
| 204 |
g/cm3 |
| 205 |
kg/dm3 |
| 206 |
kg/l |
| 207 |
kg/m3 |
| 208 |
SD_4_C |
| 209 |
SD_15_C |
| 210 |
SD_20_C |
| 211 |
g/cc |
| 212 |
lb/cf |
| 213 |
lb/gal |
| 214 |
lb/bbl |
| 215 |
SG_59_F |
| 216 |
SG_60_F |
| 217 |
SG_68_F |
| 218 |
SG_4_C |
| 219 |
SG_15_C |
| 220 |
SG_20_C |
| 221 |
Std.density unit |
| 222 |
kg/Nm3 |
| 223 |
kg/Nl |
| 224 |
g/scc |
| 225 |
kg/scm |
| 226 |
lb/scf |
| 227 |
Temperature unit |
| 228 |
deg C |
| 229 |
K |
| 230 |
deg F |
| 231 |
deg R |
| 232 |
Nom.diam.unit |
| 233 |
mm |
| 234 |
inch |
| 235 |
Mass flow |
| 236 |
Target flow |
| 237 |
Carrier flow |
| 238 |
Density |
| 239 |
calc. density |
| 240 |
Temperature |
| 241 |
Testpoint signal |
| 242 |
Zero scale |
| 243 |
Full scale 1 |
| 244 |
Dual range mode |
| 245 |
full scale 1 |
| 246 |
full scale 2 |
| 247 |
automatic |
| 248 |
Full scale 2 |
| 249 |
Active range |
| 250 |
Time constant |
| 251 |
s |
| 252 |
.2f |
| 253 |
5.2f |
| 254 |
Current span |
| 255 |
4-20 mA (25 mA) |
| 256 |
4-20 mA |
| 257 |
Failsafe mode |
| 258 |
min. current |
| 259 |
max. current |
| 260 |
Hold value |
| 261 |
actual value |
| 262 |
Simulation curr. |
| 263 |
2 mA |
| 264 |
4 mA |
| 265 |
12 mA |
| 266 |
20 mA |
| 267 |
22 mA |
| 268 |
25 mA |
| 269 |
1 mA adjust |
| 270 |
4u |
| 271 |
24 mA adjust |
| 272 |
mA |
| 273 |
Testpoint singal |
| 274 |
Zero scale |
| 275 |
Full scale 1 |
| 276 |
Dual range mode |
| 277 |
Full scale 2 |
| 278 |
Active range |
| 279 |
0-20 mA (25 mA) |
| 280 |
0-20 mA |
| 281 |
hold value |
| 282 |
0 mA |
| 283 |
10 mA |
| 284 |
Operation mode |
| 285 |
Pulse |
| 286 |
Frequency |
| 287 |
Pulse value |
| 288 |
Pulse width |
| 289 |
4.2f |
| 290 |
Hz |
| 291 |
Full scale freq. |
| 292 |
5u |
| 293 |
Full scale |
| 294 |
Output signal |
| 295 |
Passive/positive |
| 296 |
Passive/negative |
| 297 |
Active/positive |
| 298 |
Active/negative |
| 299 |
Fallback value |
| 300 |
Actual value |
| 301 |
Simulation freq. |
| 302 |
0 Hz |
| 303 |
2 Hz |
| 304 |
10 Hz |
| 305 |
1 kHz |
| 306 |
10 kHz |
| 307 |
FO1 - actual value of output frequency |
| 308 |
F01 |
| 309 |
Relay 1 function |
| 310 |
Failure |
| 311 |
Empty pipe det. |
| 312 |
Failure & EPD |
| 313 |
Dual range mode2 |
| 314 |
Batch precontact |
| 315 |
Flow direction |
| 316 |
Limit mass flow |
| 317 |
Limit vol. flow |
| 318 |
Limit std.vol.fl |
| 319 |
Limit target fl. |
| 320 |
Limit carrier fl |
| 321 |
Limit density |
| 322 |
Lim.calc.density |
| 323 |
Limit temperat. |
| 324 |
Relay 1 on-value |
| 325 |
Relay 1 off-vallue |
| 326 |
Relay 2 function |
| 327 |
Batch contact |
| 328 |
Relay 2 on-value |
| 329 |
Relay 2 off-value |
| 330 |
Batch variable |
| 331 |
mass |
| 332 |
volume |
| 333 |
Batch preset |
| 334 |
+.3f |
| 335 |
Batch prewarn |
| 336 |
compens.quantity |
| 337 |
Batching |
| 338 |
Stop |
| 339 |
Start |
| 340 |
max. batch time |
| 341 |
Batch cycle |
| 342 |
7.0f |
| 343 |
Reset batch cyc. |
| 344 |
yes |
| 345 |
Dens.adj.value |
| 346 |
Density adjust |
| 347 |
Sample fluid1 |
| 348 |
Sample fluid2 |
| 349 |
Calc. density |
| 350 |
%-MASS |
| 351 |
%-VOLUME |
| 352 |
STD.DENSITY |
| 353 |
BRIX |
| 354 |
BAUME > 1.0 SG |
| 355 |
BAUME < 1.0 SG |
| 356 |
API |
| 357 |
% BLACK LIQUOR |
| 358 |
% ALCOHOL |
| 359 |
Volume flow meas |
| 360 |
Volume&std.vol. |
| 361 |
Std.vol.calc. |
| 362 |
Calc.std.dens |
| 363 |
Fixed std.dens |
| 364 |
Reference temp. |
| 365 |
.3f |
| 366 |
Exp.coef. |
| 367 |
9.4f |
| 368 |
Fixed std.dens. |
| 369 |
Carrier density |
| 370 |
Exp.coef.carrier |
| 371 |
Target mat.dens. |
| 372 |
Exp.coef.target |
| 373 |
calc. density |
| 374 |
Total. 1 overflow |
| 375 |
Total. 2 overflow |
| 376 |
Batch upwards |
| 377 |
Batch downwards |
| 378 |
Display damping |
| 379 |
2d |
| 380 |
LCD contrast |
| 381 |
3d |
| 382 |
Language |
| 383 |
Dutch |
| 384 |
Danish |
| 385 |
Norwegian |
| 386 |
Swedish |
| 387 |
Finnish |
| 388 |
Bahasa Indonesia |
| 389 |
Japanese |
| 390 |
Noise suppress. |
| 391 |
low |
| 392 |
medium |
| 393 |
high |
| 394 |
Measuring mode |
| 395 |
unidirectional |
| 396 |
bidirectional |
| 397 |
forward |
| 398 |
reverse |
| 399 |
EPD threshold |
| 400 |
Density filter |
| 401 |
Self checking |
| 402 |
cyclic |
| 403 |
smart |
| 404 |
Select zeropoint |
| 405 |
Zeropoint 1 |
| 406 |
Zeropoint 2 |
| 407 |
Zeropoint adjust |
| 408 |
start |
| 409 |
Pos. zero return |
| 410 |
on |
| 411 |
Def. private code |
| 412 |
Access code |
| 413 |
Code entry - Safety code for local control and write protect for HART. Entering correct code dissable write protection, entering -1 enable write protection. |
| 414 |
4d |
| 415 |
Software ver.com |
| 416 |
System reset |
| 417 |
Original Calibr. |
| 418 |
Default-Param. |
| 419 |
Rst HW Data Err |
| 420 |
Rst Para.Data Er |
| 421 |
Rst Tot.Data Err |
| 422 |
K-factor |
| 423 |
Zeropoint |
| 424 |
Nominal Diameter |
| 425 |
2 |
| 426 |
4 |
| 427 |
6 |
| 428 |
8 |
| 429 |
15 |
| 430 |
25 |
| 431 |
40 |
| 432 |
50 |
| 433 |
80 |
| 434 |
100 |
| 435 |
Sensor coef. |
| 436 |
Density coef. C0 |
| 437 |
Density coef. C1 |
| 438 |
Density coef. C2 |
| 439 |
Density coef. C3 |
| 440 |
Temp. coef. km |
| 441 |
Temp. coef. kt |
| 442 |
min.temperature |
| 443 |
max.temperature |
| 444 |
.0f |
| 445 |
Software version |
| 446 |
Select testpoint |
| 447 |
TP5 osc.freq. |
| 448 |
TP10 ampl.value |
| 449 |
TP13 exc.current |
| 450 |
TP14 osc.ampl. |
| 451 |
+.1f |
| 452 |
Adv.functions |
| 453 |
Integration time |
| 454 |
Amplitude filter |
| 455 |
Oscillation ampl |
| 456 |
Freq.window |
| 457 |
Temp.indication |
| 458 |
PICK-UP check |
| 459 |
Fluid monitor |
| 460 |
Drive curr.monit |
| 461 |
1 Sample |
| 462 |
2 Samples |
| 463 |
4 Samples |
| 464 |
8 Samples |
| 465 |
16 Samples |
| 466 |
50 % |
| 467 |
75 % |
| 468 |
100 % |
| 469 |
150 % |
| 470 |
Measuring tubes |
| 471 |
Carrier tube |
| 472 |
inactive |
| 473 |
active |
| 474 |
OPTION_TOTALIZER1OVL |
| 475 |
OPTION_TOTALIZER2OVL |
| 476 |
OPTION_NOBATCH |
| 477 |
OPTION_NODENSCON |
| 478 |
OPTION_NOTESTPOINT |
| 479 |
OPTION_NOVOL |
| 480 |
OPTION_NOSTDVOL |
| 481 |
OPTION_NOSOLID |
| 482 |
OPTION_NOTOT1 |
| 483 |
OPTION_NOTOT2 |
| 484 |
OPTION_IOUT1_USED |
| 485 |
OPTION_IOUT2_USED |
| 486 |
OPTION_ERR_COMMON |
| 487 |
OPTION_ERR_PARAMETER |
| 488 |
OPTION_ERR_TOTALIZER |
| 489 |
|
| 490 |
g/s |
| 491 |
m3/s |
| 492 |
%mass |
| 493 |
%vol |
| 494 |
Brix |
| 495 |
Baume |
| 496 |
%Bl.Liq |
| 497 |
%alc |
| 498 |
deg C |
| 499 |
deg F |
| 500 |
deg R |
| 501 |
Vp |
| 502 |
ms |
| 503 |
min |
| 504 |
h |
| 505 |
% |
| 506 |
1/s |
| 507 |
s |
| 508 |
g/p |
| 509 |
kg/p |
| 510 |
t/p |
| 511 |
lb/p |
| 512 |
ton/p |
| 513 |
cm3/p |
| 514 |
dm3/p |
| 515 |
l/p |
| 516 |
hl/p |
| 517 |
m3/p |
| 518 |
cc/p |
| 519 |
gal/p |
| 520 |
bbl/p |
| 521 |
Nm3/p |
| 522 |
Nl/p |
| 523 |
scm/p |
| 524 |
scf/p |
| 525 |
Vp/p |
| 526 |
Hz/p |
| 527 |
mA/p |
| 528 |
kHz |
| 529 |
MHz |
| 530 |
e-3 1/K |
| 531 |
e-1 |
| 532 |
e5 |
| 533 |
e2 |
| 534 |
ppm/K |
| 535 |
targe_flow |
| 536 |
carrier_flow |
| 537 |
calc_density |
| 538 |
unlock prevent reset |
| 539 |
unlock prevent tot |
| 540 |
Density adjust |
| 541 |
Zeropoint adjust |
| 542 |
Notify the operator that this information must be sent before further editing. |
| 543 |
Edit Notice |
| 544 |
set_option_nobatch |
| 545 |
set_option_nodenscon |
| 546 |
set_option_notestpoint |
| 547 |
set_option_novol |
| 548 |
set_option_nostdvol |
| 549 |
set_option_nosolid |
| 550 |
set_option_notot1 |
| 551 |
set_option_notot2 |
| 552 |
set_option_iout1_used |
| 553 |
set_option_iout2_used |
| 554 |
set_option_err_common |
| 555 |
set_option_err_parameter |
| 556 |
set_option_err_totalizer |
| 557 |
reset_option_err |
| 558 |
Offline |
| 559 |
Matrix group sel. |
| 560 |
PVs |
| 561 |
Process variables |
| 562 |
Totalizers |
| 563 |
System units |
| 564 |
Current output |
| 565 |
Current output 2 |
| 566 |
Puls/Freq. output |
| 567 |
Relais |
| 568 |
Density function |
| 569 |
Display |
| 570 |
Processing para. |
| 571 |
System parameter |
| 572 |
Sensor data |
| 573 |
Service&Analysis |
| 574 |
Device Data |
| 575 |
Review |
| 576 |
FMU860 |
| 577 |
DT |
| 578 |
DVC |
| 579 |
FCX |
| 580 |
AS800 |
| 581 |
340T |
| 582 |
340C |
| 583 |
344 |
| 584 |
Siemens Micro K |
| 585 |
SITRANS L |
| 586 |
SIPAN PH |
| 587 |
SITRANS P |
| 588 |
75SMT |
| 589 |
UNIDELTA |
| 590 |
8320 |
| 591 |
SX5100 |
| 592 |
TSV175 |
| 593 |
DMU |
| 594 |
3780 |
| 595 |
BM70 |
| 596 |
8u |
| 597 |
Low Flow Cutoff- Set point that determines when the process variable will indicate 0 rather than some nominally small value. |
| 598 |
7d |
| 599 |
HART Output |
| 600 |
Status |
| 601 |
Revision #'s |
| 602 |
In write protect mode |
| 603 |
1 or 2 point adjust |
| 604 |
1 point adjust;2 point adjust |
| 605 |
Fill measuring tube with medium 1 |
| 606 |
Nominal density value fluid 1 |
| 607 |
Failure - nominal density value fluid 1 |
| 608 |
Failure - sample fluid 1 |
| 609 |
Fill tube with medium 2 |
| 610 |
Nominal density value fluid 2 |
| 611 |
Failure - nominal density value fluid 2 |
| 612 |
Failure - sample fluid 1 |
| 613 |
Density adjust running |
| 614 |
Failure - density adjust |
| 615 |
Density adjust done |
| 616 |
Start zeropoint adjust |
| 617 |
cancel;start |
| 618 |
Zeropoint adjust running |
| 619 |
Zeropoint adjust done |
| 620 |
NOTICE - This information must be sent to the transmitter to update dependent parameters. |