Device dictionary

Loading…

Reference ID	String
0	PROMAG-39
1	Positive zero return active
2	Current output simulation
3	Frequency output simulation
4	Low voltage detected
5	Sensor DAT failure
6	Sensor EEPROM failure
7	Sensor ROM/RAM failure
8	Sensor gain failure
9	Low voltage detected
10	Low reference detected
11	Value not accepted
12	EPD calibration not ok
13	EPD calibration values out of limit
14	EPD calibration values equal
15	EPD calibration values reversed
16	Flow too high
17	Current output overflow
18	Frequency output overflow
19	Batch time exceeded
20	EPD adjust running
21	Batch running
22	.5g
23	Flow Unit
24	Flow Unit - Engineering unit to be displayed with all flow values.
25	hl/min
26	hl/h
27	cc/min
28	Vol Unit
29	Volume Unit - Engineering unit to be displayed with all volumes.
30	* 1000 gal
31	Low Flow Cutoff - Set point that determines when the process variable will indicate 0 rather than some nominally small value.
32	Pulse Scaling Factor - Magnitude of volume per pulse.
33	6u
34	.2f
35	5.2f
36	Status: normal
37	Status: errors
38	FO1
39	FO1 - actual value of output frequency.
40	Tot
41	Tot >
42	Tot - Totalized Flow (Totalizer), '>' means overflow of totalizer has occurred.
43	.7g
44	*1000 gal
45	Size Unit
46	Size Unit - Unit of the nominal diameter parameter.
47	gal/bbl
48	Gallons/barrel - Defines the gallons (US or Imperial) and the amount of gallons per barrel.
49	US: 31.0
50	US: 31.5
51	US: 42.0
52	US: 55.0
53	IMP: 36.0
54	IMP: 42.0
55	Range 1
56	Range 1 Value - Defines the operational endpoint from which the Analog Value, and the 100% point of the Percent Range are derived.
57	Range 2
58	Range 2 Value - Defines the operational endpoint for the second range in the dual range mode.
59	Dual Range
60	Dual Range - This controls the dual range mode which affects the analog output.
61	Active Range
62	Range Status - Indicates the active range if in dual range mode.
63	Rng 1
64	Rng 2
65	Current Span
66	Current Span - always 4-20 mA with HART, max. output current can be either 25 mA or 20.5 mA.
67	4-20 mA (25 mA)
68	4-20 mA
69	Alarm Type
70	Analog Output Alarm Type - Defines how the Analog Output will respond when the Field Device detects that the Analog Output may not be tracking the associated Field Device Variable. NOTE - The Digital Value representation may not be determinate.
71	Low
72	High
73	Analog Sim
74	Analog Simulation - Simulates the specified analog output current.
75	2 mA
76	4 mA
77	12 mA
78	20 mA
79	22 mA
80	25 mA
81	Freq/Pulse
82	Frequency/Pulse - Controls the operation mode of the frequency and pulse output. Freq: Flow / frequency. Pulse: Volume / pulse.
83	Freq
84	Pulse
85	Pulse width - Maximum width of each pulse of the pulse output.
86	s
87	4.2f
88	Max Freq
89	Maximum Frequency - Full scale frequency for the upper range limit flow.
90	5u
91	URV
92	Upper Range Value - Flow value at maximum frequency.
93	Output
94	Output - The frequency/pulse output can generate positive or negative pulses in active (push-pull) or passive (open-collector) mode.
95	passiv/pos
96	passiv/neg
97	activ/pos
98	activ/neg
99	FO Alarm Type
100	Frequency output alarm type - Status of frequency/pulse output in error condition.
101	Freq Sim
102	Frequency Simulation - Simulation of the specified frequency for test.
103	0 Hz
104	2 Hz
105	10 Hz
106	1 kHz
107	10 kHz
108	Rel1 fct
109	Relay 1 Function - Which signal affects relay 1.
110	Failure
111	EPD
112	Failure+EPD
113	Range
114	Batch precontact
115	Flow-Dir
116	Limit 1
117	Switch on R1
118	Switch on R1 - Switch on point for relay 1.
119	Switch off R1
120	Switch off R1 - Switch off point for relay 1.
121	Rel2 fct
122	Relay 2 Function - Which signal affects relay 2.
123	Batch contact
124	Limit 2
125	Switch on R2
126	Switch on R2 - Switch on point for relay 2.
127	Switch off R2
128	Switch off R2 - Switch off point for relay 2.
129	Batch Variable
130	Batch Variable - Activates the batching functions.
131	Volume
132	Batch Preset
133	Batch Preset - Preset quantity of one batch.
134	Batch Prewarn
135	Batch Prewarn - Coarse quantity used for two-stage batching cycles.
136	Compens.Quantity
137	Compensation Quantity - used to compensate an over-/underfilling.
138	+.5g
139	Batching
140	Batching - Starting or stopping of a batch cycle.
141	Cancel
142	Start
143	Stop
144	Max. Batch Time
145	Max. Batch Time - max. allowed filling interval. This safety control function is disabled when the batch time value is set to zero.
146	Batch Cycle
147	Batch Cycle - number of batching cycles completed.
148	7.0f
149	Tot ovfl
150	Totalizer overflow - Number of overflows of the totalizer.
151	5d
152	Display Damping
153	Display Damping - time constant of the displayed flow value.
154	2u
155	Display Format
156	Display Format - number of significant digits of the flow value showed on the field device's local display.
157	x.xxxx
158	x.xxx
159	x.xx
160	LCD Contrast
161	LCD Contrast - Contrast of local Display (0 - 100%).
162	%
163	3u
164	Language
165	Language - Language of local control.
166	Dutch
167	Danish
168	Norwegian
169	Swedish
170	Finnish
171	Bahasa Indonesia
172	Japanese
173	Aux.Input
174	Aux.Input - Function assigned to the auxiliary input.
175	Reset Totalizer
176	PZR
177	Start Pulse Width
178	Start Pulse Width - Min. time of the pulse applied to the auxiliary input to activate the selected function.
179	ms
180	Positive Zero Return - all flow values are suppressed.
181	Customer Code
182	Customer Code - Safety code for local control and write protect for HART. Entering correct code disables write protection.
183	4u
184	Code Entry
185	Code Entry - Safety code for local control and write protect for HART. Entering correct code disables write protection, entering -1 enables write protection.
186	4d
187	Self check
188	Self checking - Controls self check function of the measuring amplifier.
189	SW AMP
190	Software Amplifier - Software version of amplifier module.
191	SW COM
192	Software Communication - Software version of communication module.
193	Noise sup
194	Noise sup - Noise suppression is a software filter to reduce the sensitivity against transient flows and interference peaks.
195	Low
196	Medium
197	High
198	EPD - Empty pipe detection control and calibration.
199	Adj empty pipe
200	Adj full pipe
201	EPD Delay
202	EPD Delay - Delay off empty pipe detection.
203	1 s
204	2 s
205	5 s
206	10 s
207	30 s
208	60 s
209	Meas Mode
210	Meas Mode - Bidirectional or unidirectional flow measurement.
211	unidirect
212	bidirect
213	Flow dir
214	Flow dir - Flow direction is forward or reverse.
215	forward
216	reverse
217	Ampl. Mode
218	Ampl. Mode - Amplifier in normal mode (auto-gain) or in fixed gain mode 1 to 4.
219	Normal
220	Mode 1
221	Mode 2
222	Mode 3
223	Mode 4
224	Ampl. Delay
225	Ampl. Delay - Amplifier in normal mode (auto-gain) waits a certain number of measuring samples before increasing its gain.
226	Calf pos
227	Calf pos - Sensor calibration factor in forward flow direction.
228	.4f
229	6.4f
230	Calf neg
231	Calf neg - Sensor calibration factor in reverse flow direction.
232	Zero point
233	Pipe zero - Deviation of the sensor tube's zero point.
234	Line size
235	Line size - Nominal diameter of the sensor tube.
236	.0f
237	4.0f
238	7.4f
239	max SAPS
240	max SAPS - Maximum sampling rate of sensor.
241	/ s
242	.1f
243	4.1f
244	act SAPS
245	actual SAPS - Actual sampling rate of sensor.
246	EPD electrode
247	EPD electrode - Empty pipe electrode in flow tube available.
248
249	sec
250	mA
251	Hz
252	Flow Sensor - Hardware that measures flow rate.
253	Pulse output - scaled frequency output from 0-10000 Hz, linear with input.
254	Flow Sensor - Hardware that measures flow rate.
255	Pulse Output - Scaled frequency output from 0-10000 Hz, linear with input.
256	Pulse output units - Engineering units displayed with the frequency and totalizer output values
257	Pulse output value - scaled frequency output from 0-10000 Hz, linear with input
258	Reset Totalizer - Reset the totalizer and the totalizer overflow counter.
259	Reset Batch Cycles
260	Reset Batch Cycles - Reset the batch cycle counter.
261	Master reset
262	Commands the electronics to reset and perform a selftest. Reports any errors occured.
263	Edit Notice
264	Notify the operator that this information must be sent before further editing.
265	Offline
266	Group Select
267	System Units
268	Current Output
269	Puls/Freq. Output
270	Relays
271	Display
272	Processing Para.
273	System Parameter
274	Sensor Data
275	Device Data
276	Review
277	write variables
278	FMU860
279	DT
280	DVC
281	FCX
282	AS800
283	340T
284	340C
285	344
286	Siemens Micro K
287	SITRANS L
288	SIPAN PH
289	SITRANS P
290	75SMT
291	UNIDELTA
292	8320
293	SX5100
294	TSV175
295	DMU
296	3780
297	BM70
298	8u
299	Pulse Output Unit- Engineering units that the frequency andtotalizer outputs will be displayed with.
300	Low Flow Cutoff- Set point that determines when the process variable will indicate 0 rather than some nominally small value.
301	6.2f
302	7d
303	Pulse Scaling Factor- Magnitude of process variable per pulse.
304	7.5f
305	.5f
306	HART Output
307	Status
308	Revision #'s
309	About to perform Totalizer Reset!
310	Performing Totalizer reset now
311	Totalizer reset performed
312	About to perform batch cycle counter reset!
313	Performing batch cycle counter reset now
314	Batch cycle counter reset performed
315	About to Exit Simulation Mode
316	About to Enter Simulation Mode or Changing Value
317	Simulation mode finished
318	Simulation mode entered or Value changed
319	About to reset the slave device NOTE-Loop should be removed from automatic control
320	Reset in progress, please wait
321	Device maybe stuck in selftest.
322	Master Reset OK
323	NOTICE - This information must be sent to the transmitter to update dependent parameters.
Reference ID	String