HART设备字典

Loading…

引用ID	字符串
0	6u
1	FMP200
2	SET TAG NUMBER
3
4	ERROR:RAM REFER TO OPERATING MANUAL ERROR NO. 111
5	ERROR:ROM REFER TO OPERATING MANUAL ERROR NO. 113
6	ERROR:EEPROM REFER TO OPERATING MANUAL ERROR NO. 114
7	HARDWARE ERROR REFER TO OPERATING MANUAL ERROR NO. 115
8	INITIALIZATION PLEASE WAIT WARNING NO. 103
9	CHECKSUM ERROR EEPROM DATA REFER INSTR. MANUAL ERROR NO. 101
10	FAULT SENSOR (-CONNECTION) ERROR NO. 501
11	SENSOR FAULT CHECK HF CONNECTION ERROR NO. 125
12	CHECKSUM ERROR EEPROM PROD.DATA REFER INSTR. MANUAL ERROR NO. 121
13	FAULT TEMPERATURE PROBE WARNING NO. 261
14	TEMPERATURE TOO HIGH WARNING NO. 661
15	UP-/DOWN LOAD ACTIVE REFER TO OPERATING MANUAL ERROR NO. 106
16	DOWN-LOAD ERROR REFER TO OPERATING MANUAL ERROR NO. 116
17	GAUGE DATA FRAM NOT STORED ERROR NO. 110
18	LINEARIZATION NOT EXISTANT ENTER OR DEACTIVATE ERROR NO. 605
19	MANUAL CURVE NO. OF LINEARIZATION POINTS < 2 WARNING NO. 604
20	LINEARIZATION FAILURE LINEARIZATION POINTS WARNING NO. 602
21	CURRENT OUT OF RANGE REFER MANUAL WARNING NO. 620
22	SIGNAL OUT OF RANGE WARNING NO. 643
23	MIN/MAX INDICAT.FRAM NOT STORED REFER INSTR. MANUAL WARNING NO. 102
24	SIMULATION WARNING NO. 613
25	SIGNAL NOT USABLE ERROR NO. 641
26	PROBE MAPPING ACTIVE REFER INSTR. MANUAL ERROR NO. 642
27	COMMUNICATION
28	REFLECT QUALITY
29	INSTR.&SOFTW.NO
30	OFF
31	LEVEL
32	VOLUME
33	CURRENT
34	UNIT_AFTER_LIN.
35	PROCES CONNECTION
36	STANDARD
37	INACTIVE_LENGT
38	BLOCKING DISTANCE
39	.2f
40	PERSIST. FILTER
41	3d
42	FMU860
43	DT
44	DVC
45	FCX
46	AS800
47	340T
48	340C
49	344
50	Siemens Micro K
51	SITRANS L
52	SIPAN PH
53	SITRANS P
54	75SMT
55	UNIDELTA
56	8320
57	SX5100
58	TSV175
59	DMU
60	3780
61	BM70
62	8u
63	Set to nearest possible value
64	Invalid value selection
65	CALIBRATION
66	LINEARIZATION
67	EXTENDED CAL.
68	OPER. PARAMETERS
69	SERVICE/SIMULATION
70	USER INFORMATION
71	MATRIX GROUP SEL.
72	DEVICE DATA
73	HART OUTPUT
74	OFFLINE
75	OFFLINE ORDER
76	PERCENT RANGE
77	%
78	6.1f
79	HEIGHT/DIST.
80	ACTIVATE TABLE
81	MANUAL
82	SEMIAUTOMATIC
83	CLEAR
84	Min. Span
85	LOW SENSOR LIMIT
86	.4f
87	HIGH SENSOR LIMIT
88	SERIAL-NO. SENS.
89	8d
90	FORMAT
91	SELECT UNIT
92	m
93	%
94	l
95	hl
96	m3
97	dm3
98	cm3
99	ft3
100	us_gal
101	i_gal
102	kg
103	t
104	lb.
105	ton
106
107	SIM UNIT
108	ft
109	mA
110	SELECT DIST.
111	CURR CALIBR UNIT
112	DAMPING UNIT
113	s
114	CURRENT UNIT
115	mA
116	NO UNIT
117
118	DUMMY FLOAT
119	MEASURED VALUE
120	6.0f
121	7.1f
122	7.2f
123	7.3f
124	EMPTY CALIBRATION
125	FULL CALIBRATION
126	OUTPUT DAMPING
127	3.0f
128	VALUE FOR 4 mA
129	.3f
130	VALUE FOR 20 mA
131	SAFETY ALARM
132	MIN
133	MAX
134	HOLD
135	MEAS. DISTANCE
136	6.2f
137	MEASURED LEVEL
138	LEVEL
139	LINEAR
140	LINE NO.
141	POINT 1
142	POINT 2
143	POINT 3
144	POINT 4
145	POINT 5
146	POINT 6
147	POINT 7
148	POINT 8
149	POINT 9
150	POINT 10
151	POINT 11
152	INPUT LEVEL
153	INPUT VOLUME
154	6.3f
155	MAXIMUM VOLUME
156	PROBE MAP MODE
157	FACTORY MAP
158	CUSTOMER MAP
159	PARTIAL MAP
160	CUSTOMER PROBEMAP
161	READY
162	MAP RUNNING
163	REFLFEC QUALITY
164	2d
165	ACTUAL LEVEL
166	MEASUREMENT RANGE
167	PROBE TYPE
168	UNCOATED PROBE
169	COATED PROBE
170	ASSIGN OUTPUT
171	4..20 TRES.OFF
172	4..20 TRES.ON
173	DIG.OUTP. 4/20
174	DIG.OUTP. 8/16
175	SELECT DIST. UNIT
176	m
177	ft
178	DELAY
179	DIAGNOSTIC CODE
180	4d
181	LAST DIAGNOSTIC
182	SOFTWARE NO.
183	RESET DEVICE
184	SIMULATION
185	LEVEL/DIST.
186	SIM. VALUE
187	CURRENT
188	mA
189	5.2f
190	SECURITY LOCKING
191	%-RANGE
192	probemap_digital_units_help
193	probemap_digital_value_help
194	ABORT DYNAMIC
195	Reset value?
196	Yes;No
197	LAST DIAGNOSTIC E---
198	LAST DIAGNOSTIC E%{0}
199	POST_EDIT_21
200	POST_EDIT_22
201	POST_EDIT_23
202	POST_EDIT_30
203	POST_EDIT_31
204	POST_EDIT_33
205	POST_EDIT_35
引用ID	字符串