HART设备字典

Loading…

引用ID	字符串
0	6u
1	DB 5..
2	SET TAG NUMBER
3	SERIAL NUMBER
4	CHECK CONNECTION DAT ERROR REFER INSTR. MANUAL ERROR NO. 112
5	CHECKSUM ERROR EEPROM DATA REFER INSTR. MANUAL ERROR NO. 101
6	CHECKSUM ERROR EEPROM PROD.DATA REFER INSTR. MANUAL ERROR NO. 121
7	INITIALIZATION PLEASE WAIT WARNING NR. 103
8	ERROR:EEPROM REFER TO OPERATING MANUAL ERROR NR. 114
9	ERROR:ROM REFER TO OPERATING MANUAL ERROR NR. 113
10	ERROR:RAM REFER TO OPERATING MANUAL ERROR NR. 111
11
12	CALIBRAION EMPTY = FULL;CHECK EMPTY/FULL CALIBR. ERROR NR. 610
13	SIMULATION WARNING NR. 613
14	CHECKSUM ERROR CUSTOMER PARAMETER NOT STORED ERROR NR. 110
15	DOWN-LOAD ERROR REFER TO OPERATING MANUAL ERROR NR. 116
16	UP-/DOWN LOAD ACTIVE REFER TO OPERATING MANUAL ERROR NR. 106
17	TEMP. MEASUREMENT: TOO LOW REFER INSTR. MANUAL ERROR NR. 117
18	WIRE CONTROL SIGNAL SOURCE CURR. CIRCUIT INTERRUPTED ERROR NR. 122
19	SENSOR FAULT A-SIGNAL ADC VALUE OVER OR UNDERFLOW ERROR NR. 125
20	MIN/MAX INDICATION NOT STORED REFER INSTR. MANUAL WARNING NR. 102
21	CURRENT OUT OF RANGE REFER MANUAL WARNING NR. 620
22	MANUAL CURVE NOT COMPLETE NOT USABLE ERROR NR. 605
23	LINEARIZATION FAILURE LINEARIZATION POINTS WARNING NR. 602
24	MANUAL CURVE NO. OF LINEARIZATION POINTS < 2 WARNING NR. 604
25	CORRECT. PRESSURE
26	%
27	m
28	cm
29	dm
30	ft
31	inch
32	l
33	hl
34	m3
35	dm3
36	cm3
37	ft3
38	us_gal
39	i_gal
40	kg
41	t
42	lb.
43	ton
44
45	SENSOR PRESSURE
46	7.3f
47	POSITION FACTOR
48	.3f
49	SERVICE DATA
50	FMU860
51	DT
52	DVC
53	FCX
54	AS800
55	340T
56	340C
57	344
58	Siemens Micro K
59	SITRANS L
60	SIPAN PH
61	SITRANS P
62	75SMT
63	UNIDELTA
64	8320
65	SX5100
66	TSV175
67	DMU
68	3780
69	BM70
70	8u
71	Set to nearest possible value
72	Invalid value selection
73	CALIBRATION
74	LINEARIZATION
75	EXTENDED CAL.
76	TRANSMITTER INFO
77	SERVICE/SIMULATION
78	COMMUNICATION
79	MATRIX GROUP SEL.
80	DEVICE DATA
81	HART OUTPUT
82	OFFLINE
83	PERCENT RANGE
84	%
85	6.1f
86	ACTIVATE TABLE
87	MANUAL
88	SEMIAUTOMATIC
89	CLEAR
90	SERIAL-NO. SENS.
91	7d
92	Min. Span
93	FORMAT
94	SELECT UNIT
95	mbar
96	bar
97	mH2O
98	mmH2O
99	psi
100	ftH2O
101	inH2O
102	Pa
103	MPa
104	hPa
105	mmHg
106	inHg
107	g/cm2
108	kg/cm2
109	lb/ft2
110	kgf/cm2
111	SELECT PRESS.UNIT
112	CALIBR. UNIT
113	LEVEL UNIT
114	SIMULATION UNIT
115	mA
116	TEMPERATURE UNIT
117	deg. C
118	deg. F
119	DAMPING UNIT
120	s
121	CURRENT UNIT
122	mA
123	NO UNIT
124
125	DUMMY FLOAT
126	MEASURED VALUE
127	6.0f
128	7.1f
129	7.2f
130	EMPTY CALIBRATION
131	FULL CALIBRATION
132	MIN. CURRENT 4mA
133	OFF
134	ON
135	OUTPUT DAMPING
136	4.0f
137	VALUE FOR 4 mA
138	VALUE FOR 20 mA
139	SAFETY ALARM
140	MIN.
141	MAX.
142	HOLD
143	SENSOR PRESSURE
144	6.3f
145	MEASURED LEVEL
146	LINEAR
147	LINE NO.
148	POINT 1
149	POINT 2
150	POINT 3
151	POINT 4
152	POINT 5
153	POINT 6
154	POINT 7
155	POINT 8
156	POINT 9
157	POINT 10
158	POINT 11
159	INPUT LEVEL
160	INPUT VOLUME
161	CALIBRATION MODE
162	LEVEL
163	DRY CALIBR.H
164	DRY CALIBR.%
165	PRESSURE
166	SELECT UNIT
167	DENSITY FACTOR
168	ZERO OFFSET VALUE
169	PRESSURE UNIT
170	LOW SENSOR LIMIT
171	.4f
172	HIGH SENSOR LIMIT
173	MAX. PRESSURE
174	MEASURED TEMP.
175	MAX. TEMPERATURE
176	DIAGNOSTIC CODE
177	LAST DIAGNOSTIC
178	INSTR.&SOFTW.NO
179	4d
180	RESET DEVICE
181	SIMULATION
182	OFF
183	CURRENT
184	PRESSURE
185	LEVEL/DIST.
186	VOLUME
187	SIM. VALUE
188	6.2f
189	CURRENT
190	mA
191	5.2f
192	SECURITY LOCKING
193	UNIT BEF. LIN 1
194	UNIT AFTER LIN.
195	%-RANGE
196	MeasVal+Unit
197	temperature_digital_units_help
198	temperature_digital_value_help
199	ABORT DYNAMIC
200	Reset value?
201	Yes;No
202	MAX. PRESSURE >%{0} %{1}
203	MAX. TEMPERATURE >%{0} %{1}
204	LAST DIAGNOSTIC >%{0}
205	INPUT LEVEL
206	PARAMETER NOT VALID
207	POST_EDIT_21
208	POST_EDIT_22
209	POST_EDIT_23
210	POST_EDIT_30
211	TO PREVENT ERRORS, VALUE SHOULD BE SEND TO THE FIELD DEVICE SEND VALUE?
引用ID	字符串