Device dictionary

Loading…

Reference ID	String
0	AT70
1	Endress+Hauser
2	Low voltage detected
3	Sensor DAT-failure
4	Sensor EEPROM-failure
5	Sensor PIC micro failure
6	All inputs out of range
7	Flow signal too high
8	Flow signal too low
9	Gas temp signal out of limits
10	Room temp out of range
11	Flow beyond calibration
12	Pulse rate out of range
13	Current output out of range
14	AO1
15	This is the current output value
16	mA
17	Percent of Range
18	Display of the percentage of full scale output
19	%
20	Linearisation
21	Type of linearisation of the measured value
22	Polynomial
23	Special
24	Flow unit
25	SCuMtr_hr
26	SCuMtr_min
27	SCuMtr_s
28	SL_hr
29	SL_min
30	SL_s
31	LTon_min
32	Ton_s
33	Low Flow Cutoff- Set point that determines when the process variable will indicate 0 rather than some nominally small value.
34	.2f
35	4.2f
36	PV URV
37	6.2f
38	PV USL
39	Flow damping
40	S
41	.1f
42	4.1f
43	Flow
44	Flow Min Span
45	6.1f
46	Alarm Selection
47	Analog Output during Alarm condition
48	Sensor serial
49	6d
50	O.Coll.func
51	Function of the open collector output option
52	OFF
53	Pulse
54	Pulse Scaling Factor- Magnitude of process variable per pulse.
55	.3f
56	7.3f
57	mS
58	Pulse Width- Width of the pulse output
59	3d
60	Tot. units
61	Engineering units of the totaliser & pulse output
62	SCuMtr
63	SL
64	Pulse simulation
65	Allows the user to simulate a pulse output
66	OFF
67	0%
68	50%
69	100%
70	Totaliser
71	Totaliser - Totalised Flow
72	Temp unit
73	Temperature Unit- Engineering units that the temperature will be displayed with.
74	Gas Temp
75	Field Device Process Temperature.
76	Peak Temp
77	Peak Temperature measured - maximum temperature the user has reached
78	Ambient temp
79	Temperature of the electronics pcb
80	Password
81	Local control password entry
82	4d
83	Inst. factor
84	Installation factor - scaling factor applied to the basic flow reading to allow for installation depth, etc.
85	6.3f
86	Proc. factor
87	Process factor - use selected factor to allow for such things as damp gases
88	Pipe Type
89	Shows the type of duct the sensors are in
90	Cell
91	Circular
92	Rectangular
93	Pipe width
94	Cell or Pipe width (diameter) if insertion probe
95	5.1f
96	Duct depth
97	Cell or Pipe depth in a rectangular duct
98	N. Density
99	Gas Normal Density - actual value of gas density at 0øC and 1.013 bar conditions
100	S. Density
101	Gas Standard Density - actual value of gas density at 15øC and 1.013 bar conditions
102	Cal. gas
103	Type of gas the calibration was performed on
104	User Gas
105	Type of gas selected by the user
106	TP 1
107	Test Point 1 - mV signal of the Vflow signal
108	TP 2
109	Test Point 2 - mV signal of the Vtemp signal
110	Totaliser Control
111	Allows the user to change the totaliser mode
112	ESC
113	OFF
114	ON
115	RST
116	Flow LRV
117	Minimum flowrate is always 0
118	Error bits value
119	Combined error bit flags
120	Error Code
121	Error Code for the highest priority error
122	Assy Nr
123	Assembly number of complete AT70
124	Linear range
125	Range of linear curve fit near to zero flow
126	Zero value
127	Compensated input for zero flow at process conditions
128	Software code
129	Unique software code
130	Flow MinmV
131	Reading for zero flow at calibration
132	Flow MaxmV
133	Reading for max flow at calibration
134	Zero Adjust
135	Allows the user to set a local process zero
136	Esc
137	Off
138	Set
139	Ratio Offset
140	Gas Ratio Offset
141	Ratio Scale
142	/øC
143	Gas Ratio Gain
144	Flow Sensor- Hardware that measures flow rate.
145	Gas Temperature - approximate.
146	rtemperature
147	Room Temperature - approximate.
148	Temperature - Hardware that measures the temperature within the Field Device.
149	RTemperature - Hardware that measures the temperature within the Field Device.
150	Var. Number
151	unit_0
152
153	unit_1
154	ma
155	unit_2
156	unit_3
157	sec
158	unit_4
159	mm
160	unit_5
161	kg_m3
162	unit_6
163	unit_7
164	mV
165	Index
166	Update Table
167	HotKey
168	Offline
169	Matrix group sel.
170	System Units
171	Analog Output
172	Open Collector
173	System Parameter
174	Errors/Warnings
175	Sensor Data
176	Device Data
177	Diagnostics
178	Conversion
179	write variables
180	FMU860
181	DT
182	DVC
183	FCX
184	AS800
185	340T
186	340C
187	344
188	Siemens Micro K
189	SITRANS L
190	SIPAN PH
191	SITRANS P
192	75SMT
193	UNIDELTA
194	8320
195	SX5100
196	TSV175
197	DMU
198	3780
199	BM70
200	8u
201	HART Output
202	About to change the Totaliser mode!
203	Totaliser Control:
204	Stop;Run;Reset
205	Totaliser Stopped
206	Totaliser Running
207	Totaliser Reset
Reference ID	String