Device dictionary

Loading…

Reference ID	String
0	VECTOR
1	ESP Safety
2	Analog Status
3	Time is DST
4	Analog output 2 fixed
5	Analog output 2 over limit
6	Analog output 2 under limit
7	Analog output 1 fixed
8	Analog output 1 over limit
9	Analog output 1 under limit
10	Alarm Status
11	Relay 3 Closed
12	Relay 2 Closed
13	Relay 1 Closed
14	Fault Relay Closed
15	Alarm Level 3 Active
16	Alarm Level 2 Active
17	Alarm Level 1 Active
18	Fault alarm active
19	Misc Status
20	Date/Time Invalid
21	Checksum error
22	Supply voltage low
23	Not used 2
24	Not used
25	Not used 4
26	Not used 5
27	1
28	2
29	3
30	4
31	.2f
32	8.3f
33	.1f
34	8.1f
35	.3f
36	Snsr 1
37	Snsr 2
38	Sensor Id
39	HART Cal
40	Calibration functions
41	One Cal Gas
42	Select One Calibration Gas
43	Two Cal Gas
44	Select Two Calibration Gases
45	Zero Cal Select
46	Select Zero Calibration Mode
47	Span Cal Select
48	Select Span Calibration Mode
49	More Status
50	Set More Status bit
51	Phys 13.5
52	Toggle analog output
53	Phys 13.1
54	Toggle serial data out
55	ModbusPortId
56
57	Port 1 Baud Rate
58	Port 1 Baud Rate Select
59	1200
60	1200 baud
61	2400
62	2400 baud
63	4800
64	4800 baud
65	9600
66	9600 baud
67	19200
68	19200 baud
69	38.4K
70	38.4K baud
71	57.6K
72	57.6K baud
73	115.2K
74	115.2K baud
75	Port 1 Data Bits
76	Port 1 Data Bits Select
77	7 bits
78	7 data bits
79	8 bits
80	8 data bits
81	Port 1 Parity Bits
82	Port 1 Parity Bits Select
83	None
84	No Parity
85	Odd
86	Odd Parity
87	Even
88	Even Parity
89	Port 1 Stop Bits
90	Port 1 Stop Bits Select
91	One
92	One Stop Bit
93	Two
94	Two Stop Bits
95	Port 1 Address
96	Modbus Port 1 Configuration
97	Port 1 Parity
98	Port 2 Baud Rate
99	Port 2 Baud Rate Select
100	Port 2 Data Bits
101	Port 2 Data Bits Select
102	Port 2 Parity Bits
103	Port 2 Parity Bits Select
104	Port 2 Stop Bits
105	Port 2 Stop Bits Select
106	Port 2 Address
107	Modbus Port 2 Configuration
108	Port 2 Parity
109	Serial Port
110	Serial Port Selector
111	Sensor Port
112	Host Port
113	Port Select
114	Baud Rate Select
115	Data Bits
116	Data Bits Select
117	Parity Bits
118	Parity Bits Select
119	Stop Bits
120	Stop Bits Select
121	Modbus Addr
122	Modbus Address
123	Sensor Id Number
124	Snsr Type
125	Sensor Type Select
126	UnKnwn
127	Unknown
128	PGU
129	SGOES
130	SGOES-M
131	TGAES
132	Sensor S/N
133	Sensor Serial Number
134	Sensor Version (Major)
135	Sensor Firmware Version Number
136	Sensor Version (Minor)
137	Sensor 1 Version
138	Sensor 1 Firmware Version Number
139	Sensor Version
140	Sensor Addr
141	Sensor Modbus address
142	Snsr Stat
143	Sensor Status
144	Normal
145	Fault
146	Faulted
147	Comm Fail
148	Communications Failure
149	Snsr Gas
150	Sensor Gas Name
151	Snsr Frmula
152	Sensor Gas Formula
153	Snsr 0 Cfg
154	Sensor 0 Configuration
155	Snsr 1 Type
156	Snsr 1 S/N
157	Snsr 1 Version
158	Snsr 1 Version (Major)
159	Snsr 1 Version (Minor)
160	Snsr 1 Address
161	Snsr 1 Status
162	Snsr 1 Gas Name
163	Snsr 1 Gas Frmla
164	Sensor 2 Version
165	Sensor 2 Firmware Version Number
166	Snsr 1 Cfg
167	Sensor 1 Configuration
168	Snsr 2 Type
169	Snsr 2 S/N
170	Snsr 2 Version
171	Snsr 2 Version (Major)
172	Snsr 2 Version (Minor)
173	Snsr 2 Address
174	Snsr 2 Status
175	Snsr 2 Gas Name
176	Snsr 2 Gas Frmla
177	Snsr Cnt
178	Sensors Configured
179	Supply Voltage
180	Power Supply Voltage
181	Device Stat 4
182	Device Status - 4 bytes
183	AO 2 Cal Mode
184	AO 2 Fixed
185	Snsr 2 Over limit
186	Snsr 2 Under limit
187	AO 1 Cal Mode
188	AO 1 Fixed
189	Snsr 1 Over limit
190	Snsr 1 Under limit
191	Alarm 3 Active
192	Alarm 2 Active
193	Alarm 1 Active
194	Fault Alarm Active
195	Current time is DST
196	Checksum Error
197	Supply Vltg Low
198	Analog 1 Output Fixed
199	Clear
200	Fixed
201	Analog 1 Fixed Check
202	AO 1 Overrange
203	Analog Output 1 Overrange Limit
204	Overrange
205	Analog 1 Over Limit Check
206	AO 1 Underrange
207	Analog Output 1 Underrange Limit
208	Underrange
209	Analog 1 Under Limit Check
210	Analog Output 2 Fixed
211	Analog 2 Fixed Check
212	AO 2 Overrange
213	Analog Output 2 Over Limit
214	Analog 2 Over Limit Check
215	AO 2 Underrange
216	Analog Output 2 Under Limit
217	Analog 2 Under Limit Check
218	F/W Version (Major)
219	Vector Firmware Version
220	F/W Version (Minor)
221	F/W Version
222	Vector Firmware Version Number
223	Firmware Version
224	Alarm Sensor Id
225	Alarm Select
226	Alarm Value
227	Alarm Type
228	High/Low Alarm
229	Low
230	Low alarm value
231	High
232	High alarm value
233	Alarm 1 Value
234	Alarm 2 Value
235	Alarm 3 Value
236	Alarms
237	Snsr 1 Alm 1 val
238	Snsr 1 Alm 2 val
239	Snsr 1 Alm 3 val
240	Snsr 1 Alm 1 type
241	Snsr 1 Alm 2 type
242	Snsr 1 Alm 3 type
243	Snsr 2 Alm 1 val
244	Snsr 2 Alm 2 val
245	Snsr 2 Alm 3 val
246	Snsr 2 Alm 1 type
247	Snsr 2 Alm 2 type
248	Snsr 2 Alm 3 type
249	Relay Id
250	Relay Id Number
251	Relay 0 Flags
252	Latched
253	Norm Clsd
254	Fault Rly Delay
255	Fault Rly Mode
256	Fault Rlay Mode
257	Disable
258	Fault Relay Disable
259	Open
260	Fault Relay Open
261	Closed
262	Operate
263	Fault Relay Operate
264	Fault Relay
265	Fault Relay Flags
266	Fault Relay Delay
267	Fault Relay Mode
268	Relay 1 Flags
269	Relay 1 Delay
270	Relay 1 Mode
271	Relay 1 Disable
272	Relay 1 Open
273	Relay 1 Operate
274	Relay 1
275	Relay 2 Flags
276	Relay 2 Delay
277	Relay 2 Mode
278	Relay 2 Disable
279	Relay 2 Open
280	Relay 2 Operate
281	Relay 2
282	Relay 3 Flags
283	Relay 3 Delay
284	Relay 3 Mode
285	Relay 3 Disable
286	Relay 3 Open
287	Relay 3 Operate
288	Relay 3
289	Snsr 1 Display Conc
290	Sensor 1 Display Concentration
291	Conc units
292	mg/m3
293	milligrams per cubic meter
294	LEL-M
295	lower explosive limit - meters
296	Conc Class
297	Conc PDQ
298	Conc LS
299	Conc Fmly stat
300	Conc USL
301	Conc LSL
302	Conc min span
303	Conc damp
304	Conc Update Period
305	Conc snsr s/n
306	7d
307	Simulate
308	Conc Lower trim
309	Conc Upper trim
310	Conc Trim support
311	Conc Min lower trim
312	Conc Max lower trim
313	Conc Min upper trim
314	Conc Max upper trim
315	Conc Min trim diff
316	Display conc
317	Update Period
318	Snsr 1 Calib Conc
319	Snsr 1 Calibration Concentration
320	Sensor 1 Calibration Concentration
321	Calib conc
322	Snsr 1 Temp
323	Sensor 1 Temperature
324	Snsr Temp unit
325	Sensor Temperature Units- Engineering unit to be displayed with Sensor Temperature.
326	Temperature Class
327	Temperature PDQ
328	Temperature LS
329	Temperature Fmly stat
330	Temp USL
331	Temp LSL
332	Temp min span
333	Temp Update Period
334	Temp snsr s/n
335	Temp Lower trim
336	Temp Upper trim
337	Temp Trim support
338	Temp Min lower trim
339	Temp Max lower trim
340	Temp Min upper trim
341	Tempc Max upper trim
342	Temp Min trim diff
343	Temp
344	Snsr 2 Display Conc
345	Sensor 2 Display Concentration
346	Snsr1DisplayConc
347	Snsr 2 Calib Conc
348	Sensor 2 Calibration Concentration
349	Snsr1CalibConc
350	Snsr 2 Temp
351	Sensor 2 Temperature
352	Temperature Update Period
353	Temp Max upper trim
354	Snsr 3 DisplayConc
355	Sensor 3 Display Concentration
356	Snsr 3 Calib Conc
357	Sensor 3 Calibration
358	Snsr2CalibConc
359	Snsr 3 Temp
360	Sensor 3 Temperature
361	Snsr 4 Display Conc
362	Sensor 4 Display Concentration
363	Snsr 4 Calib Conc
364	Sensor 4 Calibration Concentration
365	Snsr3CalibConc
366	Sensor 3 Calibration Concentration
367	Snsr 4 Temp
368	Sensor 4 Temperature
369	Snsr 3
370	Snsr 4
371	Selects port number
372	Port 1 (Snsr)
373	Sensor Port Select
374	Port 2 (Host)
375	Host Port Select
376	Sensor Select
377	Select sensor for menu functions
378	Sensor 1
379	Sensor 1 Select
380	Sensor 2
381	Sensor 2 Select
382	Sensor Alarm Limit
383	Selects sensor for alarm menu functions
384	Relay Select
385	Selects relay for menu functions
386	Fault Relay Select
387	Alarm 1
388	Alarm 1 Relay Select
389	Alarm 2
390	Alarm 2 Relay Select
391	Alarm 3
392	Alarm 3 Relay Select
393	DAC Select
394	Select DAC for menu functions
395	DAC 1
396	DAC 1 Select
397	DAC 2
398	DAC 2 Select
399	Test Curnt
400	Analog Output Test Current
401	Rly Latch
402	Relay Latch Setting
403	Unlatched
404	Normal State
405	Relay Normal State
406	Delay Operate
407	Relay Delay Operate
408	Relay Mode
409	Disabled
410	Sensor trim points
411	Gas Sensor
412	Temperature sensor
413	Modbus Output
414	Alarm Levels
415	Relays
416	Zero Trim Sensor 1
417	Zero Trim Sensor 2
418	Trim Sensor 1
419	Trim Sensor 2
420	Sensor trim
421	Clear calibration mode
422	Sensor trim reset
423	DAC 1 Loop Test
424	DAC 2 Loop Test
425	DAC 1 Trim
426	DAC 2 Trim
427	Leave Calibration Mode
428	Unlatch Relays
429	PV Analog Channel Saturated
430	PV Analog Channel Fixed
431	Wireless
432	WirelessHART Device
433	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
434	Primary
435	Primary Analog Channel
436	Secondary
437	Secondary Analog Channel
438	Tertiary
439	Tertiary Analog Channel
440	Quaternary
441	Quaternary Analog Channel
442	Quinary
443	Quinary Analog Channel
444	Critical Power Failure
445	Lock all
446	Trim not supported
447	Configuration cannot be changed
448	Locked by gateway
449	Analog Input Channel
450	Analog Output Channel
451	Secondary Analog Channel Saturated
452	Tertiary Analog Channel Saturated
453	Quaternary Analog Channel Saturated
454	Quinary Analog Channel Saturated
455	Secondary Analog Channel Fixed
456	Tertiary Analog Channel Fixed
457	Quaternary Analog Channel Fixed
458	Quinary Analog Channel Fixed
459	Simulation active
460	The device is in simulation mode and the level output is not representative of the process.
461	Non-Volatile memory failure
462	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
463	Volatile memory error
464	The RAM memory check is invalid or maybe corrupt
465	Watchdog reset executed
466	A watchdog reset has been performed
467	Voltage conditions out of range
468	A voltage condition is outside its allowable range
469	Environmental conditions out of range
470	An internal or environmental condition is beyond acceptable limits.
471	Electronic failure
472	A hardware problem not related to the sensor has been detected.
473	Subdevice list changed
474	Duplicate master detected
475	Capacity Denied
476	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
477	Bandwidth allocation pending
478	Block transfer pending
479	Battery life
480	Percent range
481	Loop current
482	Primary variable
483	Secondary variable
484	Tertiary variable
485	Quaternary variable
486	Read receive time
487	Write date and time
488	Non-Volatile Clock
489	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
490	Clock Uninitialized
491	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
492	No restrictions
493	SI Only
494	Restricted to SI Unit codes only
495	Process automation device
496	Discrete device
497	Hybrid:Process automation+discrete
498	I/O System
499	WirelessHART Process automation device
500	WirelessHART Discrete device
501	WirelessHART Process automation+discrete
502	WirelessHART Gateway
503	WirelessHART Access point
504	WirelessHART Process adapter
505	WirelessHART Discrete adapter
506	WirelessHART enabled handheld/portable maintenance tool
507	Device Profile
508	US
509	United States of America
510	JP
511	Japan
512	DE
513	Germany
514	FR
515	France
516	ES
517	Spain
518	RU
519	Russian Federation
520	CN
521	People's Republic of China
522	Secondary Master
523	Primary Master
524	Device Diagnostic Status 0
525	Device Diagnostic Status 1
526	I/O and Subdevice Status
527	WirelessHART Status
528	Time Set Option
529	Real Time Clock Flags
530	Country
531	Country of intended device installation
532	SI Unit Control
533	Indicates if device should only display SI unit codes
534	Time Stamp
535	Relative time value on network
536	8u
537	Dynamic Variables Returned for Device Variables
538	Command Response Truncated
539	Configuration Change Counter Mismatch
540	Status bytes mismatch
541	Device Variable
542	Variable to trim
543	ACK Count
544	Count of ACK messages received by this device
545	Analog Channel Number
546	Analog Channel Number- Index into an array of Analog Channels.
547	Index 1 into Analog Channel Array
548	Index into Analog Channel Array- Is the first of an array of addresses, whose value is identified by the Analog Channel Code.
549	Index 2 into Analog Channel Array
550	Index into Analog Channel Array- Is the second of an array of addresses, whose value is identified by the Analog Channel Code.
551	Index 3 into Analog Channel Array
552	Index into Analog Channel Array- Is the third of an array of addresses, whose value is identified by the Analog Channel Code.
553	Index 4 into Analog Channel Array
554	Index into Analog Channel Array- Is the fourth of an array of addresses, whose value is identified by the Analog Channel Code.
555	BACK Count
556	Count of BACK messages received by this device
557	STX Count
558	Count of STX messages received by this device
559	Current Date
560	Current Date based upon the real-time clock in the field device
561	Current Time
562	Current Time based upon the real-time clock in the field device
563	Set Clock Date
564	Date to set the real-time clock in the field device to, or date that the real-time clock was last set
565	Set Clock Time
566	Time to set the real time clock in the field device to, or time that the real-time clock was last set
567	%{Sensor0VersionMajor}.0%{Sensor0VersionMinor}
568	%{Sensor0VersionMajor}.%{Sensor0VersionMinor}
569	%{Sensor1VersionMajor}.0%{Sensor1VersionMinor}
570	%{Sensor1VersionMajor}.%{Sensor1VersionMinor}
571	%{ival1}.
572	%{FirmwareVersionText1}0%{ival2}
573	%{FirmwareVersionText1}%{ival2}
574	%[s]{disp_string1} Press OK when stable. Current Value %{trimDeviceVariables[device_variable_trim_code].DIGITAL_VALUE} %{trimDeviceVariables[device_variable_trim_code].DIGITAL_UNITS}
575	%[s]{disp_string1}
576	Select number of cal gases
577	One;Two
578	Device does not support two gas calibration
579	Apply input between %[5.1f]{trim_min} %{trimDeviceVariables[device_variable_trim_code].TRIM_POINT_UNITS} and %[5.1f]{trim_max} %{trimDeviceVariables[device_variable_trim_code].TRIM_POINT_UNITS}. Press OK when stable. Current Value: %{trimDeviceVariables[device_variable_trim_code].DIGITAL_VALUE}
580	Enter Cal Gas Conc in %{trimDeviceVariables[device_variable_trim_code].TRIM_POINT_UNITS}
581	Press OK when cal gas has cleared. Current Value %{trimDeviceVariables[device_variable_trim_code].DIGITAL_VALUE} %{trimDeviceVariables[device_variable_trim_code].DIGITAL_UNITS}
582	Do you really want to reset sensor %{snsr} trim?
583	Relays unlatched
Reference ID	String