Device dictionary

Loading…

Reference ID	String
0	SGOES
1	ESP Safety
2	.1f
3	8.2f
4	8.1f
5	Vol. Concentration
6	Volume Concentration value measured by device variable 0
7	.2f
8	Concentration unit
9
10	Conc Class
11	Conc PDQ
12	Conc LS
13	Conc Fmly stat
14	Conc USL
15	Conc LSL
16	Conc min span
17	Conc damp
18	Conc Update Period
19	Conc snsr s/n
20	7d
21	Simulate
22	Conc Lower trim
23	Conc Upper trim
24	Conc Trim support
25	Conc Min lower trim
26	Conc Max lower trim
27	Conc Min upper trim
28	Conc Max upper trim
29	Conc Min trim diff
30	Concentration
31	Second Device Variable (deviceVariables[1]) is concentration. xmtr-mv supports an imaginary set of expanded engineering units in this device variable slot
32	Update Period
33	% LEL Concentration value measured by device variable 1
34	Snsr temp unit
35	Sensor Temperature Units- Engineering unit to be displayed with Sensor Temperature.
36	Temperature Class
37	Temperature PDQ
38	Temperature LS
39	Temperature Fmly stat
40	Temp USL
41	Temp LSL
42	Temp min span
43	Temperature Update Period
44	Temp snsr s/n
45	Secondary Variable - Temperature Compensation
46	% LEL concentration threshold from device variable 3
47	Fourth Device Variable (deviceVariables[3]) is concentration threshold 1.
48	Concentration value measured by device variable 4
49	Fifth Device Variable (deviceVariables[4]) is concentration threshold 2.
50	Gas Type
51	Gas calibrated for
52	None
53	No gas type assigned
54	Methane
55	Propane
56	Hexane
57	Butane
58	IsoButane
59	Pentane
60	CycloPentane
61	Ethane
62	CO2
63	Methyl
64	Low Alarm Value
65	High Alarm Value
66	Alarm Select
67	Calib Type
68	Selects one or two span gas concentrations
69	One Cal Gas
70	Select One Calibration Gas
71	Two Cal Gas
72	Select Two Calibration Gases
73	Sensor trim points
74	Gas Sensor
75	Temperature sensor
76	Alarm Levels
77	Sensor trim
78	Sensor trim reset
79	Clear calibration mode
80	PV Analog Channel Saturated
81	PV Analog Channel Fixed
82	Wireless
83	WirelessHART Device
84	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
85	Primary
86	Primary Analog Channel
87	Secondary
88	Secondary Analog Channel
89	Tertiary
90	Tertiary Analog Channel
91	Quaternary
92	Quaternary Analog Channel
93	Quinary
94	Quinary Analog Channel
95	Critical Power Failure
96	Lock all
97	Trim not supported
98	Configuration cannot be changed
99	Locked by gateway
100	Analog Input Channel
101	Analog Output Channel
102	Secondary Analog Channel Saturated
103	Tertiary Analog Channel Saturated
104	Quaternary Analog Channel Saturated
105	Quinary Analog Channel Saturated
106	Secondary Analog Channel Fixed
107	Tertiary Analog Channel Fixed
108	Quaternary Analog Channel Fixed
109	Quinary Analog Channel Fixed
110	Simulation active
111	The device is in simulation mode and the level output is not representative of the process.
112	Non-Volatile memory failure
113	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
114	Volatile memory error
115	The RAM memory check is invalid or maybe corrupt
116	Watchdog reset executed
117	A watchdog reset has been performed
118	Voltage conditions out of range
119	A voltage condition is outside its allowable range
120	Environmental conditions out of range
121	An internal or environmental condition is beyond acceptable limits.
122	Electronic failure
123	A hardware problem not related to the sensor has been detected.
124	Subdevice list changed
125	Duplicate master detected
126	Capacity Denied
127	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
128	Bandwidth allocation pending
129	Block transfer pending
130	Battery life
131	Percent range
132	Loop current
133	Primary variable
134	Secondary variable
135	Tertiary variable
136	Quaternary variable
137	Read receive time
138	Write date and time
139	Non-Volatile Clock
140	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
141	Clock Uninitialized
142	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
143	No restrictions
144	SI Only
145	Restricted to SI Unit codes only
146	Process automation device
147	Discrete device
148	Hybrid:Process automation+discrete
149	I/O System
150	WirelessHART Process automation device
151	WirelessHART Discrete device
152	WirelessHART Process automation+discrete
153	WirelessHART Gateway
154	WirelessHART Access point
155	WirelessHART Process adapter
156	WirelessHART Discrete adapter
157	WirelessHART enabled handheld/portable maintenance tool
158	Device Profile
159	US
160	United States of America
161	JP
162	Japan
163	DE
164	Germany
165	FR
166	France
167	ES
168	Spain
169	RU
170	Russian Federation
171	CN
172	People's Republic of China
173	Secondary Master
174	Primary Master
175	Device Diagnostic Status 0
176	Device Diagnostic Status 1
177	I/O and Subdevice Status
178	WirelessHART Status
179	Time Set Option
180	Real Time Clock Flags
181	Country
182	Country of intended device installation
183	SI Unit Control
184	Indicates if device should only display SI unit codes
185	Time Stamp
186	Relative time value on network
187	8u
188	Dynamic Variables Returned for Device Variables
189	Command Response Truncated
190	Configuration Change Counter Mismatch
191	Status bytes mismatch
192	8.3f
193	.3f
194	Device Variable
195	Variable to trim
196	ACK Count
197	Count of ACK messages received by this device
198	BACK Count
199	Count of BACK messages received by this device
200	STX Count
201	Count of STX messages received by this device
202	%[s]{disp_string1} Current Value %[5.2f]{conc0Value} %{conc0Units}
203	%[s]{disp_string1}
204	Select number of cal gases
205	One;Two
206	Apply input between %[5.1f]{trim_min} %{deviceVariables[device_variable_trim_code].TRIM_POINT_UNITS} and %[5.1f]{trim_max} %{deviceVariables[device_variable_trim_code].TRIM_POINT_UNITS}. Press OK when stable. Current Value: %{deviceVariables[device_variable_trim_code].DIGITAL_VALUE}
207	Enter Cal Gas %{deviceVariables[device_variable_trim_code].TRIM_POINT_UNITS}
208	Waiting for cal gas to clear. Current Value: %{deviceVariables[1].DIGITAL_VALUE} %{deviceVariables[1].DIGITAL_UNITS}
Reference ID	String