Device dictionary

Loading…

Reference ID	String
0	954 SmartServo FlexLine
1	ENRAF
2	Disabled
3	Enabled
4	Critical
5	AO not Calibrated
6	Check Analog Output Upper Range and Lower Range configured
7	ROM Failure
8	Power Cycle the device. Still problem persists, Replace Electronic Module
9	RAM Failure
10	NOVRAM Failure
11	Power Cycle the device. Still problem persists, Contact Service Engineer
12	DAC Read back Failure
13	Lock/Unlock Device
14	Level
15	.3f
16	8.3f
17	7d
18	Length Unit
19	Product Level
20	Device settings
21	Diagnostics
22	Maintenance
23	Offline
24	Operate
25	Re-range
26	Device Image
27	This is an IMAGE
28	Dynamic Variables
29	PV
30	PV Analog Channel Saturated
31	PV Analog Channel Fixed
32	Wireless
33	WirelessHART Device
34	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
35	Primary
36	Primary Analog Channel
37	Secondary
38	Secondary Analog Channel
39	Tertiary
40	Tertiary Analog Channel
41	Quaternary
42	Quaternary Analog Channel
43	Quinary
44	Quinary Analog Channel
45	Critical Power Failure
46	Lock all
47	Trim not supported
48	Configuration cannot be changed
49	Locked by gateway
50	Analog Input Channel
51	Analog Output Channel
52	Secondary Analog Channel Saturated
53	Tertiary Analog Channel Saturated
54	Quaternary Analog Channel Saturated
55	Quinary Analog Channel Saturated
56	Secondary Analog Channel Fixed
57	Tertiary Analog Channel Fixed
58	Quaternary Analog Channel Fixed
59	Quinary Analog Channel Fixed
60	Simulation active
61	The device is in simulation mode and the level output is not representative of the process.
62	Non-Volatile memory failure
63	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
64	Volatile memory error
65	The RAM memory check is invalid or maybe corrupt
66	Watchdog reset executed
67	A watchdog reset has been performed
68	Voltage conditions out of range
69	A voltage condition is outside its allowable range
70	Environmental conditions out of range
71	An internal or environmental condition is beyond acceptable limits.
72	Electronic failure
73	A hardware problem not related to the sensor has been detected.
74	Subdevice list changed
75	Duplicate master detected
76	Capacity Denied
77	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
78	Bandwidth allocation pending
79	Block transfer pending
80	Battery life
81	Percent range
82	Loop current
83	Primary variable
84	Secondary variable
85	Tertiary variable
86	Quaternary variable
87	Read receive time
88	Write date and time
89	Non-Volatile Clock
90	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
91	Clock Uninitialized
92	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
93	None
94	No restrictions
95	SI Only
96	Restricted to SI Unit codes only
97	Process automation device
98	Discrete device
99	Hybrid:Process automation+discrete
100	I/O System
101	WirelessHART Process automation device
102	WirelessHART Discrete device
103	WirelessHART Process automation+discrete
104	WirelessHART Gateway
105	WirelessHART Access point
106	WirelessHART Process adapter
107	WirelessHART Discrete adapter
108	WirelessHART enabled handheld/portable maintenance tool
109	Device Profile
110
111	US
112	United States of America
113	JP
114	Japan
115	DE
116	Germany
117	FR
118	France
119	ES
120	Spain
121	RU
122	Russian Federation
123	CN
124	People's Republic of China
125	Secondary Master
126	Primary Master
127	Device Diagnostic Status 0
128	Device Diagnostic Status 1
129	I/O and Subdevice Status
130	WirelessHART Status
131	Time Set Option
132	Real Time Clock Flags
133	Country
134	Country of intended device installation
135	SI Unit Control
136	Indicates if device should only display SI unit codes
137	8u
138	Dynamic Variables Returned for Device Variables
139	Command Response Truncated
140	Configuration Change Counter Mismatch
141	Status bytes mismatch
142	Device Variable
143	Output Status
144	Output Status Byte
145	Uninitialized
146	Normal - one sensor
147	Normal - two sensors
148	Normal - three sensors
149	Shorted
150	Shorted- shorted field wiring.
151	Limited high
152	Limited high- block can not respond to upward movement of value.
153	Open
154	Open- open field wiring.
155	Limited low
156	Limited low- block can not respond to upward movement of target.
157	Initialization done
158	Initialization done- block initialization is complete.
159	Not selected
160	Not selected- target value provided by block was not selected.
161	No path
162	No path- there is no path to the process.
163	Fail
164	Fail- hardware failure.
165	Bad
166	Bad- block is out of service or has bad input.
167	Not from process
168	Not from process- value is not directly affected by any process information.
169	Local override
170	Local override- block has LO mode.
171	Not Cascade Mode
172	Not RCas Mode
173	Not ROut Mode
174	No communication
175	No communication- (NO_COM).
176	uint16_var_blk_char
177	uint32_var_blk_char
178	uint8_var_blk_char
179	int8_var_blk_char
180	new itest redef1 label
Reference ID	String