Device dictionary

Loading…

Reference ID	String
0	OXITEC 5000
1	ENOTEC GmbH
2	Error status
3	Errorstatus of OXITEC 5000
4	Const out of tolerance
5	Slope out of tolerance
6	Refgas flow too low
7	Calgas flow too low
8	Heating system failure
9	Wirebreak thermoelement
10	Errorcell o o range
11	Error probe heater
12	Alarm status
13	Temp of Elctr. o o spec
14	Probetemp too hi
15	Probetemp too lo
16	Alarm limit1
17	Alarm limit2
18	Datafault EEProm
19	Measvalue memory active
20	Error ACAL
21	Calibration Busy
22	Internal comunication
23	Int com failure
24	Calibration status
25	Calibration status of OXITEC 5000
26	Calibration OK
27	Calibration Fault
28	Calibration Active
29	Calibration Pending
30	.2f
31	8.2f
32	pv PDQ
33	PV LS
34	PV Fmly stat
35	AN CH
36	Number of analigue channels
37	One Analog Ch
38	One Out Channel.
39	SensorSerNo
40	Three byte number
41	PV Quality
42	SV Quality
43	TV Quality
44	PV Limit Status
45	SV Limit Status
46	TV Limit Status
47	Device Family Status
48	More Device Family Status Available
49	PV Var Class
50	SV Var Class
51	TV Var Class
52	PV fmly
53	SV fmly
54	TV fmly
55	.1f
56	8.1f
57	%
58	Gas level
59	Cell temperature
60	Gas Cell temperature- Hardware that measures gas level.
61	degC
62	Cell Temperature
63	Cell Voltage
64	Gas Cell voltage - Hardware that measures gas level.
65	mV
66	Cell voltage
67	Command code
68	Code
69	2d
70	Unit of the parameter
71	Dimention
72	Programmable constant. The value may be determined by the user
73	Constant
74	Slope
75	Alarm levels may be defined in OXITEC 5000. The levels are determined by the user
76	Limit1
77	Limit2
78	Limit1 func
79	Min
80	Max
81	Limit2 func
82	Setup
83	Monitor
84	Calibrate
85	Settings
86	Alarm
87	Installation data
88	HART output
89	Revision No
90	Device status
91	One point calibration
92	This menu is used for single point calibration of the detector.
93	Two point calibration
94	This menu is used for two point calibration of the detector.
95	Range values
96	This menu is used for range setting and review.
97	PV Analog Channel Saturated
98	PV Analog Channel Fixed
99	Wireless
100	WirelessHART Device
101	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
102	Primary
103	Primary Analog Channel
104	Secondary
105	Secondary Analog Channel
106	Tertiary
107	Tertiary Analog Channel
108	Quaternary
109	Quaternary Analog Channel
110	Quinary
111	Quinary Analog Channel
112	Critical Power Failure
113	Lock all
114	Trim not supported
115	Configuration cannot be changed
116	Locked by gateway
117	Analog Input Channel
118	Analog Output Channel
119	Secondary Analog Channel Saturated
120	Tertiary Analog Channel Saturated
121	Quaternary Analog Channel Saturated
122	Quinary Analog Channel Saturated
123	Secondary Analog Channel Fixed
124	Tertiary Analog Channel Fixed
125	Quaternary Analog Channel Fixed
126	Quinary Analog Channel Fixed
127	Simulation active
128	The device is in simulation mode and the level output is not representative of the process.
129	Non-Volatile memory failure
130	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
131	Volatile memory error
132	The RAM memory check is invalid or maybe corrupt
133	Watchdog reset executed
134	A watchdog reset has been performed
135	Voltage conditions out of range
136	A voltage condition is outside its allowable range
137	Environmental conditions out of range
138	An internal or environmental condition is beyond acceptable limits.
139	Electronic failure
140	A hardware problem not related to the sensor has been detected.
141	Subdevice list changed
142	Duplicate master detected
143	Capacity Denied
144	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
145	Bandwidth allocation pending
146	Block transfer pending
147	Battery life
148	Percent range
149	Loop current
150	Primary variable
151	Secondary variable
152	Tertiary variable
153	Quaternary variable
154	Read receive time
155	Write date and time
156	Non-Volatile Clock
157	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
158	Clock Uninitialized
159	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
160	None
161	No restrictions
162	SI Only
163	Restricted to SI Unit codes only
164	Process automation device
165	Discrete device
166	Hybrid:Process automation+discrete
167	I/O System
168	WirelessHART Process automation device
169	WirelessHART Discrete device
170	WirelessHART Process automation+discrete
171	WirelessHART Gateway
172	WirelessHART Access point
173	WirelessHART Process adapter
174	WirelessHART Discrete adapter
175	WirelessHART enabled handheld/portable maintenance tool
176	Device Profile
177
178	US
179	United States of America
180	JP
181	Japan
182	DE
183	Germany
184	FR
185	France
186	ES
187	Spain
188	RU
189	Russian Federation
190	CN
191	People's Republic of China
192	Secondary Master
193	Primary Master
194	Device Diagnostic Status 0
195	Device Diagnostic Status 1
196	I/O and Subdevice Status
197	WirelessHART Status
198	Time Set Option
199	Real Time Clock Flags
200	Country
201	Country of intended device installation
202	SI Unit Control
203	Indicates if device should only display SI unit codes
204	Time Stamp
205	Relative time value on network
206	8u
207	Dynamic Variables Returned for Device Variables
208	Command Response Truncated
209	Configuration Change Counter Mismatch
210	Status bytes mismatch
211	8.3f
212	.3f
213	Device Variable
214	Do you want to calibrate?
215	Aborting method due to last error
216	This will take some time
217	Calibration not started
218	Process aborted
219	Calibration OK
220	Calibration Fault
221	Calibration active
222	Calibration pending but not started
223	Unspecified fault
224	Wait while Calibrate
225	Calibration is succesfully completed
226	Calibration Pending
227	This will take some time.
228	Calibration fault
229	Upper range: %{0} % Lower range: %{1} %
230	Do you want to change?
231	Upper range :
232	Lower range :
Reference ID	String