Device dictionary

Loading…

Reference ID	String
0	X3302
1	DET-TRONICS
2	Operating Mode
3	Maintenance Required
4	Device Variable Alert
5	Operating Mode 2
6	Apply clean air
7	Stabilizing zero
8	Apply cal gas
9	Stabilizing span
10	Remove cal gas
11	Xmtr Addstatus 0
12	Field Device Specific Status Byte 1- Data that has Field Device status information relating to: failures / warnings / status of processes.
13	Fire Alarm
14	Indicates (Y) if the device is in a fire alarm status. - analog output is at 20mA, fire alarm relay is actuated and LED is red.
15	Oi Cal Active
16	Optical Integrity (Oi) Calibration is in progress. During caibration the detector should be cleaned and covered. Flame detection is disabled until calibration is complete.
17	Manual Oi Active
18	A manual Optical Integrity (Oi) test is in progress. During caibration the detector should be cleaned and covered. Flame detection is disabled until calibration is complete.
19	Warm-Up
20	Device is in the power-up time delay (warm-up) mode. Normal duration 30 seconds.
21	Not Used
22	Not Used, bit 4
23	Not Used, bit 5
24	Not Used, bit 6
25	Not Used, bit 7
26	Xmtr Addstatus 1
27	Field Device Specific Status Byte 2- Data that has Field Device status information relating to: failures / warnings / status of processes.
28	Not Used, bit 0
29	Not Used, bit 1
30	Not Used, bit 2
31	Not Used, bit 3
32	Xmtr Addstatus 2
33	Field Device Specific Status Byte 3- Data that has Field Device status information relating to: failures / warnings / status of processes.
34	Fault
35	Indicates (Y) if a fault condition exists.Go to (Device Info) and select (Status Info) to determine the nature of the fault.
36	Automatic Oi Fault
37	Automatic Oi Fault. Check viewing windows and Oi reflector plate for cleanliness.
38	Manual Oi Fault
39	The detector has failed the last manual Oi test.
40	Oi Cal Fault
41	An Oi calibration fault has occured.
42	Diminished Detect Fault
43	Diminished Detection Fault. Excessive background IR radiation.Eliminate IR interference and/or re-aim/orient detector.
44	Detection Disable Fault
45	Flame detector function has been disabled! Check viewing windows for cleanliness and/or presence of excessive background IR signal. If uncorrectable replace sensor.
46	Temp Out of Range
47	Detector integral temperature out of range-Operating range: -40F to +167F (-40C to +75C).
48	Voltage Out of Range
49	Supply voltage is out of range. Specified operating voltage is 18 to 30 Vdc.
50	Xmtr Addstatus 3
51	Field Device Specific Status Byte 4- Data that has Field Device status information relating to: failures / warnings / status of processes.
52	Sensor Hdwr. Flt
53	Sensor hardware fault. -If fault clears 3 minutes after powerup check man oi test line not connected to DC- -Verify supply volt is within Operating range (18 to 30 Vdc) If fault does not clear, replace sensor module.
54	HIB Hardware Fault
55	HART interface board (HIB) hardware fault. If fault persists replace HIB.
56	Internal Com. Flt
57	Internal communication fault. If fault persists replace HART interface board and/or sensor module.
58	Incompatible Firmware Fault
59	Sensor module firmware version is not compatible with HART interface board. Replace the sensor module.
60	.5f
61	None
62	No units defined.
63	.3f
64	.2f
65	8.2f
66	The user is encouraged to keep track of the last calibration date here. This date is for information only and is not used in any internal calculations.
67	CalDate
68	7d
69	Event log request
70	new event
71	previous event
72	next event
73	exit
74	Set Password
75	The password is used to validate the command to enable or disable writes in the device.
76	Set Write Protect
77	Used to set the write protect mode. With Write Protect (On), variables cannot be written to the device and commands that cause actions to be performed in the device cannot occur.
78	Change Password
79	Sensor Unit
80	Minimum Span
81	AO Alarm type
82	% Range
83	Xfer Function
84	Range Unit
85	PV Snsr S/N
86	Conc
87	Self Test
88	Self test will perform all internal checks immediately and return results in variables xmtr flt 1 & xmtr flt 2.
89	Condensed Status
90	Write Protect
91	Abort response test
92	return to normal
93	Fire
94	No
95	Yes
96	Oi Calibrate Active
97	Oi Calibration is active.
98	Manual Oi is active.
99	Warm Up
100	Fault
101	Automatic Oi Fault
102	Oi Calibrate Fault
103	Diminish. Detect. Flt
104	Detect. Disable Flt
105	Temp Range Fault
106	Voltage Fault
107	Sensor Hdwr. Fault
108	HIB Hardware Fault
109	HART Interface Board hardware fault. If fault persists replace HIB. DEC PN 007308-005
110	Internal communication fault. If fault persists replace HART interface board and/or sensor module.
111	Incompatible Fault
112	RTC Seconds
113	RTC seconds values 0-59.
114	.2d
115	RTC Minutes
116	RTC minutes values 0-59.
117	RTC Hours
118	RTC hours values 0-23.
119	RTC Date
120	RTC date values 1-31.
121	RTC Month
122	RTC month values 1-12.
123	RTC Year
124	RTC year values 0-99.
125	Log Temperature
126	Log Code
127	-
128	Normal
129	Warmup
130	Soft Reset
131	Hardware Reset
132	Fire Alrm
133	Man Oi Pass
134	Man Oi Fault
135	Auto Oi Fault
136	Oi Cal Pass
137	Oi Cal Fault
138	Loop Test
139	4-20 Cal
140	Clk Reset
141	Password Rst
142	Hardware Fault
143	Det Dsabl Fault
144	Dimimished Detect
145	Volt Fault
146	Temp Fault
147	Clr Evnt Log
148	HART Hardware Fault
149	MB Comm Fault
150	Incompat Fault
151	Fire Relay L/NL
152	Fire relay, latching(L) or non-latching(NL).
153	L
154	NL
155	Fire Relay NE/NDE
156	Fire relay, normally energized(NE) or normally de-energized(NDE).
157	NDE
158	NE
159	Fault Relay L/NL
160	Fault relay, latching(L) or non-latching(NL).
161	Fault Relay NE/NDE
162	Fault relay, normally energized(NE) or normally de-energized(NDE).
163	Aux Relay L/NL
164	AUX relay, latching(L) or non-latching(NL).
165	Aux Relay NE/NDE
166	AUX relay, normally energized(NE) or normally de-energized(NDE).
167	Sensitivity
168	Detector sensitivity setting: Very high, High, Medium, or Low.
169	Very High
170	High
171	Medium
172	Low
173	Consecutive Oi Fails
174	Allowable number of consecutive Oi failures to produce a fault. Factory set to 3 (minutes). This is the time between fault occurrence and annunciation.
175	Temp Setpoint
176	Temperature at which heater begins operating. (-55C to+75C)
177	Heater Power
178	Actual heater power (0-100%). Heater prevents condensation and icing on the detector optics.
179	Heater Setpoint
180	Maximum amount of heater power allowed (in percent of full power, 0-100).
181	Response Time
182	Fire alarm processing time in seconds.
183	Error
184	3 Sec
185	Oi Fail Count
186	Number of consecutive Oi failures counted (one passed Oi test resets the counter).
187	Left Oi
188	Percent of calibrated Oi test signal returned by the left sensor. Reading should be 90 to 110 percent. If reading is below 90 percent, first try clean the window if the reading is still below 90 go to (Device Setup), select (Calibration) and perform Oi Calibration. If over 110% recalibrate.
189	Middle Oi
190	Percent of calibrated Oi test signal returned by the middle sensor. Reading should be 90 to 110 percent. If reading is below 90 percent, first try clean the window if the reading is still below 90 go to (Device Setup), select (Calibration) and perform Oi Calibration. If over 110% recalibrate.
191	Right Oi
192	Percent of calibrated Oi test signal returned by the right sensor. Reading should be 90 to 110 percent. If reading is below 90 percent, first try clean the window if the reading is still below 90 go to (Device Setup), select (Calibration) and perform Oi Calibration. If over 110% recalibrate.
193	Voltage
194	Actual detector supply voltage. Specified operating voltage is 18 to 30 Vdc.
195	Temperature
196	Actual integral temperature of detector.
197	Part Number
198	Manufacturer's part number for this device.
199	.6d
200	Dash Number
201	Manufacturer's secondary part number for this device.
202	.3d
203	Manufacture Date
204	Date of manufacture. Shown as month/day/year
205	Sensor Firmware
206	Firmware revision level of sensor module.
207	HART Firmware
208	Firmware revision level of HART interface board (HIB).
209	Junk
210	X3302 Root Menu
211	Device Info Menu
212	Command Menu
213	Device Setup Menu
214	Calibration Menu
215	HART Command Menu
216	General Info Menu
217	Status Info Menu
218	Oi Menu
219	Hardware Menu
220	Detector Settings
221	Real Time Clock
222	Configuration Menu
223	HART PV Menu
224	HART Info Menu
225	HART Setup
226	History Menu
227	Write variables
228	Calibrate Oi
229	This procedure calibrates the Oi test signal for all three IR sensors.
230	Start Passive Oi
231	Test to check the cleanliness of the detector's optical surfaces and the ability to respond to an IR signal. Relays unaffected.
232	Start Active Oi
233	Test to check the cleanliness of the detector's optical surfaces and the ability to respond to an IR signal. Relays are affected.
234	Clear Oi Fault
235	Clear prior Oi faults. If the cause of the fault has not been corrected, subsequent Oi faults will occur.
236	Reset Latches
237	Latched relays are reset. LED turns green.
238	Master Reset
239	Initiates a hardware reset for both the sensor and the HART interface. Latched relays are reset.
240	Clear Data Log
241	Clears data log entries contained on the HART interface board.
242	Alarm Log
243	Scroll through 32 Alarm Logs with date, time, and temperature stamp.
244	Fault Log
245	Scroll through 32 Fault Logs with date, time, and temperature stamp.
246	General Log
247	Scroll through 32 General Logs with date, time, and temperature stamp.
248	X3302 Abort Method.
249	Part Number
250	Current time and date setting of real time clock. Factory set to GMT minus 6 hours. Date: month/day/year Time: Hour:minute:second
251	Serial Number
252	Serial number of device.
253	FMU860
254	DT
255	DVC
256	FCX
257	AS800
258	340T
259	340C
260	344
261	Siemens Micro K
262	SITRANS L
263	SIPAN PH
264	SITRANS P
265	75SMT
266	UNIDELTA
267	8320
268	SX5100
269	TSV175
270	DMU
271	3780
272	BM70
273	8u
274	Oi calibration - Important! Clean and cover the detector before proceeding.
275	Oi calibration.
276	Cmd 130, Status Response Fault.
277	Cmd 48, Status Response Fault.
278	Checking status.
279	Checking status...
280	Uncover Detector Window.
281	Success
282	Passive Oi.
283	Active Oi - Warning: This will cause an alarm indication.
284	Clear Oi fault.
285	Relay Latch reset.
286	Hardware reset - Remove from loop.
287	Clearing data logs... Are you sure?
288	To Few Bytes Received.
289	%{1}-%{2}-%{0} %{3}:%{4} %{6}C %{7}
290	Current;Previous;Next;Exit
291	Warning: Current method abort.
292	Part Number %{0}-%{1}
293	Real Time Clock Date: %{0}/%{1}/%{2} Time: %{3}:%{4}:%{5}
294	Device Serial Number: 000%{0}
Reference ID	String