Device dictionary

Loading…

Reference ID	String
0	UD10
1	DET-TRONICS
2	Operating Mode
3	Display Status 1
4	Cal Line Active
5	Cal Sw Active
6	HART Test
7	LON Attached
8	Response Test
9	Manual Self Test
10	Input HART
11	Reserved
12	Display Status 2
13	Any Fault
14	Cal Active
15	Warm Up Mode
16	Low Relay Active
17	Hi Relay Active
18	Aux Relay Active
19	Current Fixed
20	MB Write Protect
21	Device Status 1
22	Calibration Active
23	Warm Up
24	Low Alarm
25	Aux Alarm
26	High Alarm
27	Self Test
28	Configuration Change
29	Alignment Mode
30	Device Status 2
31	Write Protect
32	4-20 Fixed
33	Sensor Removed
34	Sensor End Of Life
35	Loop Test Active
36	TDSA Alarm
37	Quick Alarm
38	Generic Status
39	Display Fault 1
40	12v Fault
41	5v Fault
42	3v Fault
43	Output Loop Fault
44	Input Loop Fault
45	Display Fault 2
46	FRAM Fault
47	ADC Ref Voltage Fault
48	24v Fault
49	Flash Fault
50	RAM Fault
51	WDT Fault
52	Device Fault 1
53	Loop Fault
54	Supply Voltage Fault
55	Calibration Fault
56	Memory Fault
57	ADC Fault
58	Internal Voltage Fault
59	Zero Drift
60	Temperature Sensor Fault
61	Device Fault 2
62	Wrong Sensor Type
63	Lamp Fault
64	Alignment Fault
65	Blocked Optic Fault
66	Sensor Fault
67	Noise Fault
68	Align ADC Fault
69	Device Fault 3
70	Align Fault
71	Align Warning
72	DAC Fault
73	High Fault
74	Low Fault
75	Device Warm Up
76	Ref Channel Fault
77	Act Channel Fault
78	Device Fault 4
79	Incompatible Version
80	Detection Disable Fault
81	Oi Fault
82	Diminished Detect Fault
83	Communication Fault
84	General Fault
85	Gas Value
86	.2f
87	%
88	Percentage Composition
89	PPM
90	PPM units
91	VOL%
92	VOL units
93	%LFL
94	LFL units
95	PPB
96	PPB Units
97	C
98	Degrees C
99	mA
100	milliamperes
101	LFL*M
102	LEL Meters
103	PPM*M
104	PPM Meters
105	VOL*M
106	VOL Meters
107
108	Not used enumeration
109	No enumeration
110	Unknow enumeration
111	.3f
112	Analog Output
113	8.2f
114	Upper Range Value
115	10.2f
116	Lower Range Value
117	8.3f
118	Serial Number
119	7d
120	Request Index
121	Event Log Request
122	FIRST
123	PREV
124	NEXT
125	LAST
126	Response Index
127	TimeStamp
128	Cal Code
129	Empty Log
130	1
131	2
132	Zero_Cal
133	Span_Cal
134	Abort_Cal
135	Failed_Cal
136	7
137	8
138	9
139	10
140	Clr Cal Flt
141	Event Code
142	No Event
143	Power Up
144	Low Alarm On
145	High Alarm On
146	Aux Alarm On
147	EE Flt On
148	ADC Ref Flt On
149	24v Flt On
150	Flash Flt On
151	RAM Flt On
152	WDT Flt On
153	12V Flt On
154	5V Flt On
155	3 V Flt On
156	Out Loop Flt On
157	In Loop Flt On
158	High Flt On
159	Low Flt On
160	Zero Drift Flt On
161	Cal Flt On
162	Optics Flt On
163	Low Voltage On
164	Cal Active Strt On
165	Active ADC Flt On
166	Active ADC Sat Flt On
167	Tx Warmup
168	CGS Loop Flt On
169	CGS Comm Flt
170	High 24v Flt
171	Bank 1 Repaired
172	Bank 2 Repaired
173	Input Loop Cal Failed
174	Mode Changed
175	Input Loop Cal Passed
176	Fire Alm On
177	UV Pre Alm On
178	IR Pre Alm On
179	UV Alm On
180	IR Alm On
181	Misc Alm On
182	Rep Alm On
183	Pwr Flt On
184	Gen Flt On
185	Oi Flt On
186	Oi Pre Flt On
187	High IR1 Flt On
188	High IR2 Flt On
189	Short Ckt Flt On
190	Low Alarm Off
191	High Alarm Off
192	Aux Alarm Off
193	EE Flt Off
194	ADC Ref Flt Off
195	24v Flt Off
196	Flash CRC Flt Off
197	RAM Flt Off
198	Ext WDT Flt Off
199	12v Flt Off
200	5v Flt Off
201	3v Flt Off
202	Outp Loop Flt Off
203	Inp Loop Flt Off
204	High Flt Off
205	Low Flt Off
206	Zero Drift Flt Off
207	Cal Flt Off
208	Optics Flt Off
209	Low Volt Flt Off
210	Cal Active Strt Flt Off
211	Active ADC Flt Off
212	Active ADC Sat Flt Off
213	Sensor OK
214	TX Warmup Off
215	CGS Loop Flt Off
216	Fire Alm Off
217	UV Pre Alm Off
218	IR Pre Alm Off
219	UV Alm Off
220	IR Alm Off
221	Misc Alm Off
222	Pre Alm Off
223	Power Flt Off
224	Gen Flt Off
225	Oi Flt Off
226	Oi Pre Flt Off
227	High IR1 Flt Off
228	High IR2 Flt Off
229	Short Ckt Flt Off
230	Zero Value
231	10.8f
232	Span Value
233	Low Alarm Level
234	Gas level for initiating a low alarm. The low alarm level can not be set lower than 5%LEL*M or higher than the high alarm level.
235	High Alarm Level
236	Gas level for initiating a high alarm. The high alarm level can not be set higher than 60%LEL*M or lower than the low alarm level.
237	Auxilary Alarm Level
238	Gas level for initiating an auxilary alarm.
239	Aux Alarm Latch
240	Selects latching or nonlatching aux alarm. Latched alarms are unlatched with Reset.
241	High Alarm Latch
242	Selects latching or nonlatching high alarm. Latched alarms are unlatched with Reset.
243	Low Alarm Latch
244	Selects latching or nonlatching low alarm. Latched alarms are unlatched with Reset.
245	Password
246	The password is used to validate the command to enable or disable writes in the device.
247	Set Write protect
248	Used to set the write protect mode.
249	Change Password
250	Local Zero Value
251	Local zero value.
252	Max Temp -Time
253	Min Temp -Time
254	Self test will perform all internal checks immediately and return results in variables xmtr flt 1 & xmtr flt 2.
255	This command will reset latched relay outputs
256	Firmware Revision
257
258	Hardware Revision
259	Response test
260	This test holds the analog output at 4mA and prevents the alarm relays from activating when gas is applied. Gas response is indicated by the PV.
261	Abort response test
262	Return to normal
263	Reset Latched Alarms
264	This command will reset the latched alarms
265	Calibration log
266	Retrieves stored calibration events. The most recent calibration event is shown first. Calibrations are recorded as zero only cal, cal OK & cal failed. Cal OK indicates that both zero and span were completed.
267	Event log
268	Retrieves stored events. The most recent event is shown first. Recorded events include Blocked Optics, warm up, zero drift, low alarm & high alarm.
269	Change Mode
270	DD Build Version
271	Internal DD build version number.
272	Sensor Calibration
273	Detector gas calibration method. Follow prompts to apply and remove calibration gas.
274	Abort Calibration Method.
275	Abort Method.
276	Display History
277	History
278	Display Fault/Status Info
279	Display Info
280	Device Status Menu
281	Device History Info
282	Device Setup
283	Device HART Option
284	Device Info
285	Device Fault/Status
286	Device Info 2
287	Sensor Info
288	Alarm Setting
289	Display HART Option
290	Main Menu
291	Process Variables
292	Display Status Menu
293	Display Setup
294	Display Test Menu
295	Display General Info
296	Display RTC
297	Write variables
298	Device Cal
299	Extended Fault/Status
300	Seconds
301	RTC seconds value 1-59.
302	Minutes
303	RTC minutes value 1-59.
304	Hours
305	RTC hours value 1-23.
306	Week
307	Month
308	RTC month value 1-12.
309	Invalid
310	Jan
311	Feb
312	Mar
313	Apr
314	May
315	Jun
316	Jul
317	Aug
318	Sep
319	Oct
320	Nov
321	Dec
322	Day
323	RTC day value 1-7.
324	Year
325	RTC year value 1-12.
326	Tx Running Hours
327	Sensitivity
328	Sensor Type
329	Sensor Part Number
330	Sensor Hardware Revision
331	Firmware Rev
332	Normal
333	Calibration in progress
334	Warm up
335	Calibration State
336	Waiting for Zero
337	Apply Clean Air
338	Waiting for Gas
339	Waiting for Span
340	Remove Cal Gas
341	Terminate
342	Complete
343	Hardware Rev
344	Revision
345	Universal Rev
346	Fld Dev Rev
347	Software Rev
348	Max Temp
349	3.2f
350	Running Hrs
351	Min Temp
352	Gas Name
353	Cal Gas Concentration
354	Response Factor
355	Manufacturer
356	Dev ID
357	Model
358	GT3000
359	X3301
360	OPECL_TX
361	OPECL_RX
362	ECLIPSE
363	PIR
364	Master Adrs Select
365	Primary
366	Secondary
367	Cal Point Zero
368	Cal Point Span
369	F
370	T
371	High Alarm NE/NDE
372	Alarm setting, normally enabled or normally disabled
373	NDE
374	NE
375	Low Alarm NE/NDE
376	Aux Alarm NE/NDE
377	Extended Byte 0
378	Extended Byte 1
379	Extended Byte 2
380	Extended Byte 3
381	Pre-Alarm
382	Fire Alarm
383	UV Pre-Alarm
384	IR Pre-Alarm
385	UV Alarm
386	IR Alarm
387	Misc Alarm
388	Extended Byte 4
389	Extended Byte 5
390	Extended Byte 6
391	Extended Byte 7
392	X Fault
393	Oi Pre-Fault
394	High IR1 Fault
395	High IR2 Fault
396	Short Circuit Fault
397	Power Fault
398	SV Value
399	SV Units
400	Upper Limit
401	Lower Limit
402	Minimum Span
403	Damping
404	TV Value
405	TV Units
406	QV Value
407	QV Units
408	Error code not defined.
409	The real-time data returned from the field device has not changedsince the last time it was read OR The data sent to the field device has been rounded or truncated dueto limitations within the field device
410	This code indicates that the command was not executedNo Response Data Bytes are returned from the field device.
411	The requested (e.g., loop current) mode is not valid. This code indicates that the command was not executed.No Response Data Bytes are returned from the field device.
412	The requested command is not implemented
413	Tx Write protect error
414	FMU860
415	DT
416	DVC
417	FCX
418	AS800
419	340T
420	340C
421	344
422	Siemens Micro K
423	SITRANS L
424	SIPAN PH
425	SITRANS P
426	75SMT
427	UNIDELTA
428	8320
429	SX5100
430	TSV175
431	DMU
432	3780
433	BM70
434	8u
435	Date: %[02d]{day}/%[02d]{month}/%[04d]{year} Time: %[02d]{hours}:%[02d]{mins}:%[02d]{secs}
436	Self Test Completed Successfully!
437	Performing Reset for Latched Alarms
438	Firmware Revision: %[2d]{msb}.%[02d]{lsb}
439	Hardware Revision: %[2d]{msb}.%[02d]{lsb}
440	Setting fld dev output to 4mA. Proceed?
441	PV %{0} %{1} AO %{2} mA
442	Reset the Latched Alarms
443	Processing Calibration Log...
444	Exiting, device is busy.
445	%{1} Date: %[02d]{2}-%{3}-%[02d]{4} Time: %[02d]{5}:%[02d]{6}:%[02d]{7} Zero: %[4.2f]{8} Span: %[4.2f]{9}
446	first;previous;next;End
447	Calibration Log Calcode:%{1} Timestamp:%{2}
448	%{1} Date: %[02d]{2}-%{3}-%[02d]{4} Time: %[02d]{5}:%[02d]{6}:%[02d]{7}
449	Input Password
450	Input Choice
451	Disable;Enable;Change Password;End
452	Protection Change Success
453	Protection Change Error
454	Input New Password
455	Password Change Success
456	Password Change Error
457	Changing Write Protect/Password State
458	Detector Electronics Corp. UD10 Build Version: 02.14 Build Date: 22-Oct-2010
459	Fault: Calibration mode is active.
460	Fault: Warmup mode is active.
461	WARNING!: Entering device calibration mode. Calibration gas is required for successful completion.
462	Starting calibration sequence.
463	Fault: Normal mode active.
464	Fault: Warmup mode active.
465	Cal mode active.
466	Waiting For Zero
467	Waiting For Gas
468	Waiting For Span
469	Calibration Complete
470	WARNING: Fault detected!
471	Abort Calibration in Progress.
472	Please Wait...
473	Calibration Aborted.
474	Aborting Method
Reference ID	String