Device dictionary

Loading…

Reference ID	String
0	Live Rate
1	Display of Active unaveraged ReadIn rate.(Cps live)
2	.0f
3	.1f
4	.2f
5	.3f
6	.4f
7	.5f
8	cps
9	PV
10	Digital representation of measured process value(PV->Primary Variable).
11	Device Status
12	Represents the Status of the Field Device in accordance to NE107 Normal Valid output signal. Maintenance required(M) Still valid output signal. Out of specification(S) Signal out of specified range. Function check(C) Temporary non-valid output signal. Failure(F) Non-valid output signal.
13	FAILURE
14	OUT OF SPEC.
15	FUNCTION CHECK
16	MAINTENANCE REQ.
17	NORMAL
18	Current AO Status
19	Actual Current Loop Status
20	SIGNALING
21	SATURATED
22	FIXED
23	FIXED & SATURATED
24	Data Quality
25	BAD
26	UNCERTAIN
27	MANUAL
28	GOOD
29	Limit Status
30	Family Status
31	Density Suspension
32
33	Io Rate
34	Measurement Status
35	Display of actual measurement status.
36	OK
37	No help needed
38	CODE 1
39	Background >= Calibration point pulse rate
40	CODE 2
41	Invalid calibration point number
42	CODE 3
43	Calibration is not monotonic
44	CODE 4
45	Invalid coefficient value
46	CODE 5
47	Invalid calibration point value
48	CODE 6
49	Invalid calibration date
50	CODE 7
51	Unexpected calibration failure
52	CODE 8
53	Invalid range values
54	Meas Rate
55	Rate for adjustment of meas point.
56	Operating Hours
57	Operating Hours- The counter value represents the accumulated release time of operation in hours
58	h
59	Date
60	Actual system date (mm/dd/yyyy).
61	Time
62	Actual system time (hh:mm:ss).
63	00:00:00
64	Operating Mode
65	Displays actual System Operating Mode.
66	INIT
67	STARTUP
68	SHUTDOWN
69	ERROR
70	WARNING
71	HOLD
72	TEST
73	RUN
74	Instruction Code
75	No instruction needed!
76	1.Change - Electronics 2.Contact BT service
77	1.Restart device 2.Change - Electronics 3.Contact BT service
78	1.Restart device 2.Check - PMT connector - PMT detector unit - Electronics 3.Contact BT service
79	1.Restart device 2.Check - EMC environment 3.Contact BT service
80	1.Check - Detector temperature environment - Temperature alarm setup
81	1.Check - Process - Process alarm setup
82	1.Check - Detector settings - PMT connector - PMT detector unit - Electronics 2.Restart 3.Contact BT service
83	1.Acknowledge event 2.Retry download 3.Try another file
84	1.Retry download 2.Use calibration wizard for new configuration 3.Upload new configuration
85	1.Acknowledge event 2.Restart 3.Check - Try to set Date/Time 4. Contact BT service
86	1.Wait download... it will be finished automatically.
87	1.Wait sampling... it will be finished automatically.
88	1.Wait plateau measurement... it will be finished automatically.
89	1.Wait calibration... it will be finished automatically.
90	1.Exit simulation mode
91	1.Check - Detector calibration - Pulse rate - Range values - Influence of radiation interference 2.Contact BT service
92	1.Check - Detector calibration 2.Contact BT service
93	1.This is a notifcation to check the activated alarm setup after a new calibration has been performed 1.Check device alarm setup 2.Acknowledge event
94	1.Calibrate device by using the Quick Start Wizard
95	1.Acknowledge event 2.Check actual measurement configuration 3.Run new calibration
96	1.Acknowledge event 2.Run new calibration 3.Contact BT service
97	1.Reboot device 2.Change electronics
98	1.Check - Configuration 2.Restart 3.Change electronics
99	1.Restart device 2.Contact BT service
100	1.Run factory reset 2.Run reboot
101	Event Code
102	Event Code which is actually signaled by the Field device.
103	NO EVENT
104	F100
105	F101
106	F102
107	F103
108	S104
109	F105
110	F106
111	C107
112	C108
113	C109
114	C110
115	C111
116	C112
117	C113
118	C114
119	S115
120	S116
121	S117
122	S118
123	S119
124	F120
125	F121
126	F122
127	F123
128	F200
129	F201
130	F202
131	F203
132	F204
133	F205
134	F206
135	F207
136	F300
137	S301
138	S302
139	F303
140	F304
141	F305
142	S306
143	S307
144	S308
145	S309
146	F310
147	S311
148	S312
149	S313
150	F314
151	F315
152	F316
153	F317
154	S318
155	S319
156	S320
157	F321
158	F322
159	F323
160	F400
161	F401
162	S402
163	S403
164	S404
165	S405
166	F406
167	F407
168	S408
169	S409
170	F410
171	F411
172	S412
173	S413
174	S414
175	S415
176	S416
177	S417
178	S418
179	S419
180	F420
181	F421
182	F422
183	F423
184	F500
185	F501
186	F502
187	F503
188	F504
189	F505
190	F506
191	F507
192	F600
193	S601
194	F602
195	F603
196	F604
197	F605
198	F606
199	F607
200	F700
201	F701
202	F702
203	F703
204	F704
205	F705
206	F706
207	F707
208	F800
209	F801
210	F802
211	F803
212	F804
213	F805
214	F806
215	F807
216	F900
217	F901
218	F902
219	F903
220	F904
221	F905
222	F906
223	F907
224	FALSE
225	TRUE
226	Detector Temp.
227	Actual detector temperature value.
228	Detector Temp. Mode
229	Select detector temperature mode. Select 'Fix Value' for test.
230	OFF
231	ON
232	Detector Temp. Min
233	Minimum device temperature since last reset.
234	Detector Temp. Max
235	Maximum device temperature since last reset.
236	HV Setpoint
237	Display of actual HV Setpoint at multiplier.
238	HV Feedback
239	Display of actual HV feedback at multiplier.
240	HV Average
241	Display HV Average as detector raw value. HV Average has a damping value of 10 days. The value is used for error messages 'HV-Error' and 'Change Multiplier'.
242	Display of detector live count rate.
243	Meas Channel
244	Control Channel
245	Auxiliary Channel
246	HV Mode
247	Display actual HV mode
248	AUTO
249	Sensor works with HV auto mode
250	PLATEAU
251	Relay State
252	NO ALARM
253	ALARM
254	Current Mode
255	A fixed current value is simulated.
256	Average Rate
257	The ReadIn rate is newly averaged in every measurement cycle. Standardized to one second.
258	Compensation Date
259	Date of last compensation (mm/dd/yyyy).
260	Remaining Time
261	Time remaining while ReadIn.
262	Background
263	Enter backgound radiation count rate.
264	Cal Rate
265	Rate for adjustment of Cal Point.
266	PB Flag
267	RC Flag
268	LM Flag
269	PN Flag
270	DISABLE
271	ENABLE
272	PV Unit
273	Density Unit
274	g/cm³
275	kg/m³
276	lb/gal
277	lb/ft³
278	g/l
279	Concentration Unit
280	Selected solids content Unit
281	wt%
282	Coefficient 0
283	.3e
284	.4e
285	.5e
286	.6e
287	.7e
288	.8e
289	.9e
290	Coefficient 1
291	Coefficient 2
292	Coefficient 3
293	cm6/g³
294	0
295	1
296	2
297	Detector Type
298	Select detector type.
299	CPS Format
300	x
301	x.x
302	x.xx
303	x.xxx
304	x.xxxx
305	x.xxxxx
306	Length Format
307	Temperature Format
308	Voltage Format
309	Dummy Variable PV
310	Dummy Variable PRODUCT
311	Dummy Variable ABS COEFF
312	Dummy Variable COEFF
313	Method Integer Type Variable
314	Method Float Type Variable
315	Download Active
316	Is Online
317	BACKGROUND
318	Read-in background count rate
319	ACTIVE POINT
320	Read-in count rate of active point.
321	IIC Address
322	The IIC Address of the requested module.
323	PV Format
324	CPS Display Format
325	CPS Edit Format
326	Coeff Format
327	x.xxxExxx
328	x.xxxxExxx
329	x.xxxxxExxx
330	x.xxxxxxExxx
331	x.xxxxxxxExxx
332	x.xxxxxxxxExxx
333	x.xxxxxxxxxExxx
334	Density Classification
335	Concentration Classification
336	Solids Content Classification
337	Length Unit
338	Selected length unit used for measuring path
339	Product Unit
340	Selected unit used for slurry solid- and liquid density
341	Temp. Unit
342	Selected detector temperature unit
343	°C
344	°F
345	cm²/g
346	1/cm
347	cm4/g²
348	Device variable family
349	PV Damping Value
350	Shows the active time constant. The value 0.0 leaves the count rate unfiltered.
351	PV UL
352	Calculated Upper Transducer Limit Value- Upper limit in which the measurement is valid, i.e. monotonic.
353	PV LL
354	Calculated Lower Transducer Limit Value- Lower limit in which the measurement is valid, i.e. monotonic.
355	Cal UL
356	Calculated Upper Transducer Limit Value- Upper limit in which the calibration is valid, i.e. monotonic.
357	Cal LL
358	Calculated Lower Transducer Limit Value- Lower limit in which the calibration is valid, i.e. monotonic.
359	Minimum Span
360	PV Mode
361	A fixed PV value is simulated.
362	SIMULATE
363	Pulse Rate Mode
364	A fixed Rate value is simulated.
365	Update Period
366	Liquid Density
367	Density of carrier liquid
368	Solid Density
369	Density of solid in the slurry
370	Abs.Coefficient
371	Abs.Coefficient of slurry
372	R-Squared
373	R-Squared of regression curve.
374	PV Upper Limit
375	PV Lower Limit
376	Hysteresis
377	Relay Assignment
378	Select DO Relay assignment.
379	Relay alarm state depends on Failure(F) events
380	FAILURE OOS
381	Relay alarm state depends on Failure(F) and OutOfSpecification(OOS) events
382	PV ALARM
383	Relay alarm state depends on whether PV Value goes beyond or above configured threshold limits
384	TEMP ALARM
385	Relay alarm state depends on whether Detector temperature goes beyond or above configured threshold limits
386	ReadIn Mode
387	Select Read-in mode.
388	Read-in disabled
389	QUICKSTART RATE
390	Cal Status
391	Display of actual calibration configuration status.
392	3
393	4
394	5
395	6
396	7
397	8
398	No instruction needed
399	Check that background rate is smaller than any calibration point pulse rate!
400	Check validity of calibration points. Check if calibration points number fits to selected calibration method!
401	Check if calibartion points and curve are monotonic For SOLIDS CONTENT adapt LRV or URV according the calculated values of LL and UL!
402	Check coefficient values!
403	Check calibration point values!
404	Check system Date & Time!
405	Unexpected calibration failure - Contact Berthold Technologies!
406	Check validity of upper and lower range values (URV,LRV)!
407	Calibration Status
408	Display of actual calibration status.
409	Meas Mode
410	Selected measuring mode.Can be changed using Quick Start Wizard only.
411	DENSITY
412	CONCENTRATION
413	SOLIDS CONTENT
414	Cal Method
415	Used calibration method.
416	DIRECT ENTRY
417	1-POINT
418	Calibration with one point
419	2-POINT
420	Calibration with two points
421	MULTIPOINT
422	Calibration with more than two points
423	Selected calibration method.Can be changed using the Quick Start Wizard only.
424	Cal Mode
425	Select calibration mode.
426	INACTIVE
427	No operation. (Idle mode)
428	RECALL
429	Use measurement parameter for calibration
430	RESTORE
431	CALIBRATE
432	Start calibration calculation
433	PRESET
434	Cal Point No.
435	Active point for the displayed calibration point informations.
436	9
437	10
438	11
439	Max Nbr Cal Points
440	Maxium index of calibration curve.
441	01
442	02
443	03
444	04
445	05
446	06
447	07
448	08
449	09
450	Value 01
451	Value 02
452	Value 03
453	Value 04
454	Value 05
455	Value 06
456	Value 07
457	Value 08
458	Value 09
459	Value 10
460	Value 11
461	Cal Value
462	Cal Point value [PV units]
463	Cal Density Unit
464	Rate 01
465	Rate 02
466	Rate 03
467	Rate 04
468	Rate 05
469	Rate 06
470	Rate 07
471	Rate 08
472	Rate 09
473	Rate 10
474	Rate 11
475	Selected unit used in density mode
476	Selected unit used in concentration mode
477	Solid Contents Unit
478	Selected unit used in solid contents mode
479	Measuring Path
480	Enter inner diameter of pipe.
481	Cal LRV
482	Lower Range Value.Defines the minimum usable value within the calibration range.
483	Cal URV
484	Upper Range Value.Defines the maximum usable value within the calibration range.
485	PV Factor
486	PV Value is multiplied with this actual constant gain factor.
487	PV Offset
488	This actual constant offset value is added to PV Value.
489	Set by User
490	Coefficients are set by User
491	Channel
492	CHANNEL-1
493	CHANNEL-2
494	CHANNEL-3
495	CHANNEL-4
496	CHANNEL-5
497	Receiver
498	Language
499	English
500	Deutsch
501	Français
502	Italiano
503	Español
504	Português
505	Brightness
506	Content
507	CURRENT AO
508	AVG RATE
509	Format
510	Acknowledge Error
511	Download Start
512	Download Stop
513	Upload Start
514	Upload Stop
515	HART Serial No.
516	7d
517	Access Code
518	Type in access code to change access level.
519	8.0f
520	Access Level
521	Actual access level. The access levels are used to control actions that a user is allowed to perform.
522	BASIC
523	STANDARD
524	ADMIN
525	Function Check
526	Enables general field device function check signaling (Cxxx Codes).
527	No Function Check signaling.
528	Device is signaling function check (Cxxx).
529	Primary Master
530	Enables specific function check signaling (Cxxx Codes) as soon as a Primary HART Master communicates with field device.
531	No signaling when secondary master is active.
532	Device is signaling function check (Cxxx) as long a Primary/Secondary HART Master communicates.
533	Secondary Master
534	Enables specific function check signaling (Cxxx Codes) as soon as a Secondary HART Master communicates with field device.
535	Local User Interface
536	Enables specific function check signaling (Cxxx Codes) as soon as a Local User Interface or PC communicates with field device.
537	No signaling when Local User Interface is active.
538	Device is signaling function check (Cxxx) as long a Local User Interface communicates.
539	Module Name
540	Module Ident Number
541	Module Revision
542	Diagnostic Behaviour
543	Define signaling in cases where field device detects process alarm.
544	No signaling when device detects PV alarm.
545	OOS
546	Device signals out of specification event code (Sxxx) as soon as PV threshold is exceeded. The device continues to measure. A diagnostic message is generated.
547	Device signals failure event code (Fxxx) as soon as PV threshold is exceeded. Measurement will be interrupted. A diagnostic message is generated.
548	Defines signaling in cases where field device detects temperature alarm.
549	No signaling when device detects temperature alarm.
550	Device signals out of specification event code (Sxxx) as soon as temperature threshold is exceeded. The device continues to measure. A diagnostic message is generated.
551	Device signals failure event code (Fxxx) as soon as temperature threshold is exceeded. Measurement will be interrupted. A diagnostic message is generated.
552	Reset Device
553	Enable device reset mode.
554	REBOOT
555	FACTORY RESET
556	MODIFICATION LOG RESET
557	ERROR LOG RESET
558	Event Group 100
559	Sytem Event Group
560	Event Group 200
561	Mainboard Event Group
562	Event Group 300
563	Detector Event Group
564	Event Group 400
565	Application Layer(DNS) Event Group
566	Event Group 500
567	CurrentOut Event Group
568	Event Group 600
569	DigitalOut Event Group
570	Event Group 700
571	DataLink Layer(HMI) Event Group
572	Event Group 800
573	Application Layer(HMI) Event Group
574	Event Group 900
575	Application Layer(HART) Event Group
576	Event Log Index
577	Active index of log entry.
578	Event Code of log entry.
579	Occurence date of log entry.
580	Occurence time of log entry.
581	Description
582	Description of log entry.
583	Bus Address Source
584	DEFAULT
585	HARDWARE
586	SOFTWARE
587	Bus Address
588	Enter Profibus address of device.
589	Detector Temp. Test
590	Enter test value for detector temperature.
591	Temp. Upper Limit
592	Enter upper temperature limit of device.
593	Temp. Lower Limit
594	Enter lower temperature limit of device.
595	Enter hysteresis for device temperature limit.
596	Temp Extrema
597	Enable reset of detector temperature extrema
598	Reset is inactive.
599	RESET
600	Reset Temperature Extrema now.
601	NaI 40x35
602	NaI point detector Size 40x35mm
603	Polymer 50x60
604	Polymer point detector Size 50x60mm
605	HV Manual
606	Display and setpoint of HV manual.
607	HV Default
608	Display and setpoint of HV default.
609	HV Start
610	Enter HV start value for plateau measurement beginning.
611	4u
612	HV Stop
613	Enter HV stop value for plateau measurement end.
614	HV Step
615	Enter HV step width for plateau measurement step width.
616	Meas. Time
617	Enter measuring time for each plateau measuring point.
618	Plateau Records
619	Plateau Date
620	Plateau HV
621	HV of Active displayed plateau table entry
622	Plateau Impulses
623	Impulses of Active displayed plateau table entry
624	Error Value
625	Defines current value in case of error
626	Supply Mode
627	Defines if the current loop is supplied by internal or external supply voltage. (Internal Supply->Source Mode / External Supply->Sink Mode)
628	SINK
629	SOURCE
630	Ident No.
631	Identification Number - Number that is used for identification purposes by Berthold Technologies
632	Serial No.
633	Serial Number - Number that is used for identification purposes by Berthold Technologies
634	Lower Limit
635	Enter lower limit for current output. According NE43 it is recommended to set Lower Limit value to 3.8mA
636	Current Behaviour
637	Enables or disables function check signaling by current value.
638	Current Value
639	Enter function check current value. This value is set by field device in cases where function check codes are signaled.
640	Upper Limit
641	Enter upper limit for current output. According NE43 it is recommended to set Upper Limit value to 20.5mA
642	Relay
643	Relay Test Value
644	Relay Mode
645	Pulse Rate
646	Cal Time
647	Time of last calibration (hh:mm:ss).
648	Cal Date
649	Date of last calibration (mm/dd/yyyy).
650	Nuclide
651	Select nuclide for decay compensation.
652	Cs-137
653	Decay compensation will be done with Cs-137
654	Co-60
655	Decay compensation will be done with Co-60
656	Active background radiation count rate only for decay compensation.
657	Read-in Time
658	Enter averaging time for Read-in procedure.
659	Firmware Rev.
660	Firmware Rev- Information to identify the Field Device embedded software by Berthold Technologies
661	Firmware Date
662	Firmware Date- Time of Field Device embedded software build. This information is used by Berthold Technologies
663	Feedback monitor
664	Function to activate current feedback monitor function
665	Plateau Index
666	Active plateau table Index
667	Classification
668	Solids Content Unit
669	Value out of limits
670	Loop Warning
671	Test PV
672	PV simulation ON/OFF
673	Test Rate
674	CPS simulation ON/OFF
675	Change Supply
676	Method to change loop supply mode.
677	post_write_upload_variables
678	Reset Change Flag
679	This method resets the modification flag
680	Reboot
681	This method performs a system reboot.
682	Factory Reset
683	This method performs a factory reset on the device.
684	Master Reset
685	This method performs a master reset on the device.
686	Acknowledge
687	This method allows to acknowledge actual event code
688	Event Description
689	This description refers to actual event code
690	Event Instruction
691	This instruction refers to actual event code
692	Cal Help
693	This help text refers to actual calibration status
694	Cal Instruction
695	This instruction refers to actual calibration status
696	Relay DO
697	Refresh Plateau
698	Refresh graphical views of plateau.
699	Reset
700	Refresh
701	Set Poll Addr
702	Change HV Mode
703	Method to switch HV mode between manuell and automatic
704	Start / Stop
705	Method to start or stop plateau measurement
706	Calibrate
707	The device will be calibrated using the actual configured calibration parameter set.
708	Restore Upload
709	Upload and decay compensation of former calibration data.
710	Recall
711	All calibration parameters will be overwritten with the actual used measurement parameter set.
712	Read-in
713	Clear
714	Select Point
715	Select specific calibration point
716	Reset Calibration Point Index
717	Quick Start Wizard
718	pre_write_upload_variables
719	pre_read_download_variables
720	post_read_download_variables
721	Current
722	mA
723	Rate
724	Temperature
725	Dynamic Variables
726	Cal Table
727	Index
728	Value
729	Meas Table
730	Actually used measurement table
731	Module Info
732	No
733	ID
734	Name
735	Revision
736	PV Meter
737	Primary variable (PV) Meter
738	AO Meter
739	CurrentOut(AO) Meter
740	Plateau Curve
741	Plateau
742	HV
743	V
744	Plateau Table
745	Event Log
746	Event Counter
747	Counter
748	Date1
749	Time1
750	Date2
751	Time2
752	Date3
753	Time3
754	Date4
755	Time4
756	Date5
757	Time5
758	Offline View
759	Identification
760	Location
761	Device Information
762	Device Revision
763	Setup
764	Sstem
765	Sensors
766	Calibration
767	Signal Condition
768	Outputs
769	Alarms
770	Interfaces
771	Units
772	Formats
773	Detector
774	Cal Parameter
775	Current AO
776	Parameter Setup
777	Sensor Settings
778	Damping
779	Tuning
780	Cal Settings
781	Cal Coeffs
782	Process
783	Diagnostics(NE107)
784	Profibus Setting
785	IR Remote Control
786	Local Display
787	Quick Diagnostics
788	Online Menu
789	Process Variables
790	Device Setup
791	Diagnostics
792	Access
793	User Access
794	HART Master Access
795	HART DO
796	Simulation
797	Admin
798	Device Diagnostic
799	HART Diagnostics
800	HART Change Status
801	Event Overview
802	Event Group 100...
803	Event Group 200...
804	Event Group 300...
805	Event Group 400...
806	Event Group 500...
807	Event Group 600...
808	Event Group 700...
809	Event Group 800...
810	Event Group 900...
811	Process Monitor
812	Charts
813	Trends
814	System Monitor
815	Active Configuration
816	System
817	Date / Time
818	High Voltage
819	Range
820	Process Alarm
821	Temperature Alarm
822	Diagnostics Alarm (NE107)
823	Cal Points
824	Cal Background
825	Cal Limits
826	Cal Product Condition
827	Detector Info
828	Hardware Info
829	Device Reset
830	Meas Parameter
831	Meas Product Condition
832	Meas Coefficients
833	Plateau Graph
834	Plateau Data
835	Plateau Measurement
836	Device
837	Wizard
838	Process Values
839	Process Overview
840	Diagnostic
841	Diagnostic Overview
842	Device Diagnostics
843	HART Device Status
844	HART Communication Status
845	HART Ext. Device Status
846	HART Lock Device Status
847	Error Log
848	Event Group 108...
849	Event Group 116...
850	Event Group 308...
851	Event Group 316...
852	Event Group 408...
853	Event Group 416...
854	PV Simulation
855	CPS Simulation
856	AO Simulation
857	DO Simulation
858	Berthold Device
859	Quick Start Image
860	Device Image
861	HartLogo
862	Diagnostics Link
863	Device Status Image
864	Parameter Upload
865	Parameter Download
866	Device Type
867	LB414
868	PV out of limits
869	Process applied to the primary variable is outside the operating limits of the field device. The PV is beyond its operating limit.
870	Non PV out of limits
871	Process applied to the non-primary variable is outside the operating limits of the field device A device variable not mapped to the PV is beyond its operating limits.
872	PV AO saturated
873	Analog output 1 and its digital representation are outside the operating range limits, and not responding to input The Loop current has reached its upper or lower endpoint limit and cannot increase or decrease any further.
874	PV AO fixed
875	Analog output 1 and its digital representation are in fixed mode, and not responsive to input changes The Loop current is being held at a fixed value and is not responding to process variations.
876	More status available
877	Field device has more status available via Command 48. Read Additional Status device specific information.
878	Cold start
879	A reset or self test of the field device has occurred, or power has been removed and reapplied
880	Configuration changed
881	A modification has been made to the configuration of the field device
882	Device malfunction
883	Field device has malfunctioned due to a hardware error or failure The device detected a serious error or failure that compromises device operation.
884	Ext. Device Status
885	Write Protect
886	Current AO Mode
887	FIXED VALUE
888	Actual Current is the analogue representation of measured Process Value (usually 4-to-20mA).
889	Alarm Type
890	HIGH
891	Current output in case of failures: 22mA
892	LOW
893	Current output in case of failures: 2 mA
894	VALUE
895	Current output in case of failures: User defined value
896	Transfer Function
897	LINEAR
898	SQUARE
899	CUBIC
900	UNDEFINED
901	PV % Range
902	PV URV
903	Defines the relationship between the Loop Current 20.0mA and the Primary Variable Upper Range Value.Defines the maximum usable value within the measurment range.
904	PV LRV
905	Defines the relationship between the Loop Current 4.0mA and the Primary Variable Lower Range Value.Defines the minimum usable value within the measurment range.
906	Long Tag
907	Communication Status
908	Short Tag
909	Descriptor
910	Message
911	Device ID
912	Poll Addr
913	Final Assembly No.
914	Final Assembly Number - Number that is used for identification purposes, and is associated with the overall Field Device. This number can be used by the user in any way. There is no specific recommended use.
915	DD Rev.
916	Device Rev.
917	Software Rev.
918	Universal Rev.
919	No. Req Preams
920	No. Resp Preams
921	Modification Counter
922	F200 Runtime failure
923	F201 HW failure
924	F201 Hardware failure detected
925	F202 HW failure
926	F202 Hardware failure detected
927	F203 HW failure
928	F203 Hardware failure detected
929	F204 HW failure
930	F204 Hardware failure detected
931	F205 failure
932	F206 failure
933	F207 failure
934	S416 Alarm Setup notification
935	S416 Check activated Alarm Setup against new measurement configuration
936	S417 OOS
937	S418 OOS
938	S419 OOS
939	F420 failure
940	F421 failure
941	F422 failure
942	F423 failure
943	F100 HW module
944	F100 Hardware module missing or not tested
945	F101 Permanent memory
946	F101 Permanent memory failure
947	F102 Data memory
948	F102 Data memory failure
949	F103 Internal system failure
950	S104 Real time clock OOS
951	S104 Real time clock failure out of specification limits
952	F105 Watchdog reset
953	F105 Watchdog reset failure
954	F106 Up-/Download
955	F106 During up/download the data are not correctly transmitted.
956	C107 Local operation
957	C107 Local operation is active.
958	C108 Download active
959	C108 Parameter download to device is active.
960	C109 Read-in active
961	C109 Read-in is active.
962	C110 Plateau active
963	C110 Plateau measurement is active.
964	C111 Calibration active
965	C111 Calibration is active.
966	C112 Current AO simulation
967	C112 Current AO simulation is active.
968	C113 PV simulation
969	C113 PV simualtion is active.
970	C114 DO simulation
971	C114 DO simulation is active.
972	S115 Real time clock OOS
973	S115 Real time clock out of specification limits
974	S116 Device is not calibrated
975	S117 OOS
976	S118 OOS
977	S119 OOS
978	F120 failure
979	F121 failure
980	F122 failure
981	F123 failure
982	F300 Runtime failure
983	S301 DAC calibration OOS
984	S301 DAC calibration values out of specification limits
985	S302 ADC calibration OOS
986	S302 ADC calibration values out of specification limits
987	S303 Hardware failure
988	S303 Hardware failure detected
989	S304 Hardware failure
990	S304 Hardware failure detected
991	F305 Zero pulse rate measurement channel
992	F305 No impulses in measurement channel
993	S306 Zero pulse rate control channel
994	S306 No impulses in control channel
995	S307 Zero pulse rate auxiliary channel
996	S307 No impulses in auxiliary channel
997	S308 Zero pulse rate in reserved channel
998	S308 No impulses in reserved channel
999	S309 Instable pulse rate
1000	F310 Pulse deviation measurement channel
1001	F310 Pulse rate deviation in measurement channel
1002	S311 Threshold measurement channel OOS
1003	S311 Threshold measurement channel out of specification
1004	S312 Threshold control channel OOS
1005	S312 Threshold control channel out of specification
1006	S313 Threshold auxiliary channel OOS
1007	S313 Threshold auxiliary channel out of specification
1008	S314 Generated HV voltage OOS
1009	S314 Generated HV voltage out of specification
1010	F315 HV voltage monitoring
1011	F315 HV voltage monitoring failure
1012	F316 HV reached its limit value
1013	F317 HV lower limit failure
1014	F317 HV average is 20% below default HV
1015	S318 HV upper limit OOS
1016	S318 HV average is 40% above default HV
1017	S319 Temperature sensor malfunction
1018	S319 Temperature sensor malfunction failure
1019	S320 Temperature closely to max limits OOS
1020	S320 Temperature closely to max limits specifications
1021	F321 Temperature max limit exceeded
1022	F322 Detector malfunction
1023	F322 Detector malfunction failure
1024	F323 Hardware failure
1025	F700 Init failure
1026	F701 Runtime failure
1027	F702 failure
1028	F703 failure
1029	F704 failure
1030	F705 failure
1031	F706 failure
1032	F707 failure
1033	F800 Init failure
1034	F801 Runtime failure
1035	F802 failure
1036	F803 failure
1037	F804 failure
1038	F805 failure
1039	F806 failure
1040	F807 failure
1041	F600 Runtime failure
1042	S601 Digital output malfunction
1043	F602 failure
1044	F603 failure
1045	F604 failure
1046	F605 failure
1047	F606 failure
1048	F607 failure
1049	F400 Runtime failure
1050	F401 Measurement configuration failure
1051	S402 Measurement decay compensation
1052	S402 Measurement decay compensation out of specification
1053	S403 Calibration decay compensation
1054	S403 Calibration decay compensation out of specification
1055	S404 PV upper limit OOS
1056	S404 PV out of upper limit specification
1057	S405 PV lower limit OOS
1058	S405 PV out of lower limit specification
1059	F406 PV Upper limit failure
1060	F406 PV Upper Limit failure
1061	F407 PV Lower limit failure
1062	F407 PV Lower Limit failure
1063	S408 Temperature upper limit OOS
1064	S408 Temperature out of upper limit specification
1065	S409 Temperature lower limit OOS
1066	S409 Temperature out of lower limit specification
1067	F410 Temperature upper limit failure
1068	F411 Temperature lower limit failure
1069	S412 Restore OOS
1070	S412 Configuration is out of specification
1071	S413 Measurement count rate upper limit OOS
1072	S413 Measurement count rate is out of upper limit specification
1073	S414 Measurement count rate lower limit OOS
1074	S414 Measurement count rate is out of lower limit specification
1075	S415 PV Calculation OOS
1076	S415 PV Calculation is out of limit specification
1077	F500 Runtime failure
1078	F502 CLoop monitoring failure
1079	F502 Current loop monitoring failure
1080	F501 CLoop deviation failure
1081	F503 CLoop malfunction failure
1082	F503 Current loop malfunction failure
1083	F504 failure
1084	F505 failure
1085	F506 failure
1086	F507 failure
1087	F900 Runtime failure
1088	F901 failure
1089	F902 failure
1090	F903 failure
1091	F904 failure
1092	F905 failure
1093	F906 failure
1094	F907 failure
1095	Primary Variable Code
1096	Device Lock Status
1097	Locked
1098	Locked Permanent
1099	Locked by Primary Master
1100	Lock / Unlock
1101	Test Current
1102	DAC Trim
1103	PV Analog Channel Saturated
1104	PV Analog Channel Fixed
1105	Wireless
1106	WirelessHART Device
1107	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
1108	Primary
1109	Primary Analog Channel
1110	Secondary
1111	Secondary Analog Channel
1112	Tertiary
1113	Tertiary Analog Channel
1114	Quaternary
1115	Quaternary Analog Channel
1116	Quinary
1117	Quinary Analog Channel
1118	Critical Power Failure
1119	Lock all
1120	Trim not supported
1121	Configuration cannot be changed
1122	Locked by gateway
1123	Analog Input Channel
1124	Analog Output Channel
1125	Secondary Analog Channel Saturated
1126	Tertiary Analog Channel Saturated
1127	Quaternary Analog Channel Saturated
1128	Quinary Analog Channel Saturated
1129	Secondary Analog Channel Fixed
1130	Tertiary Analog Channel Fixed
1131	Quaternary Analog Channel Fixed
1132	Quinary Analog Channel Fixed
1133	Simulation active
1134	The device is in simulation mode and the level output is not representative of the process.
1135	Non-Volatile memory failure
1136	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
1137	Volatile memory error
1138	The RAM memory check is invalid or maybe corrupt
1139	Watchdog reset executed
1140	A watchdog reset has been performed
1141	Voltage conditions out of range
1142	A voltage condition is outside its allowable range
1143	Environmental conditions out of range
1144	An internal or environmental condition is beyond acceptable limits.
1145	Electronic failure
1146	A hardware problem not related to the sensor has been detected.
1147	Subdevice list changed
1148	Duplicate master detected
1149	Capacity Denied
1150	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
1151	Bandwidth allocation pending
1152	Block transfer pending
1153	Battery life
1154	Percent range
1155	Loop current
1156	Primary variable
1157	Secondary variable
1158	Tertiary variable
1159	Quaternary variable
1160	Read receive time
1161	Write date and time
1162	Non-Volatile Clock
1163	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
1164	Clock Uninitialized
1165	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
1166	None
1167	No restrictions
1168	SI Only
1169	Restricted to SI Unit codes only
1170	Process automation device
1171	Discrete device
1172	Hybrid:Process automation+discrete
1173	I/O System
1174	WirelessHART Process automation device
1175	WirelessHART Discrete device
1176	WirelessHART Process automation+discrete
1177	WirelessHART Gateway
1178	WirelessHART Access point
1179	WirelessHART Process adapter
1180	WirelessHART Discrete adapter
1181	WirelessHART enabled handheld/portable maintenance tool
1182	Device Profile
1183	US
1184	United States of America
1185	JP
1186	Japan
1187	DE
1188	Germany
1189	FR
1190	France
1191	ES
1192	Spain
1193	RU
1194	Russian Federation
1195	CN
1196	People's Republic of China
1197	Device Diagnostic Status 0
1198	Device Diagnostic Status 1
1199	I/O and Subdevice Status
1200	WirelessHART Status
1201	Time Set Option
1202	Real Time Clock Flags
1203	Country
1204	Country of intended device installation
1205	SI Unit Control
1206	Indicates if device should only display SI unit codes
1207	8.3f
1208	Time Stamp
1209	Relative time value on network
1210	8u
1211	Dynamic Variables Returned for Device Variables
1212	Command Response Truncated
1213	Configuration Change Counter Mismatch
1214	Status bytes mismatch
1215	Device Variable
1216	WARN - Current AO should be removed from automatic control!
1217	Device is in write protect mode!
1218	Device is in offline mode!
1219	Activate PV simulation...
1220	Deactivate PV simulation...
1221	NOTE - Current AO may be returned to automatic control!
1222	Activate Rate simulation...
1223	Deactivate Rate simulation...
1224	Loop will be switched to SOURCE MODE!
1225	Changing supply mode now?
1226	Cancel;Yes
1227	Loop will be switched to SINK MODE!
1228	WARN - HART communication will be not possible as long the loop isn't supplied externally !!!
1229	Trim was not done.
1230	Reset modification flag now?
1231	Modification Flag is reset!
1232	Reboot device now?
1233	Rebooting... %{l_iProcessPercent}%
1234	Updating parameters... 0%
1235	Updating parameters... 2%
1236	Updating parameters... 4%
1237	Updating parameters... 6%
1238	Updating parameters... 8%
1239	Updating parameters... 10%
1240	Updating parameters... 12%
1241	Updating parameters... 14%
1242	Updating parameters... 16%
1243	Updating parameters... 18%
1244	Updating parameters... 20%
1245	Updating parameters... 22%
1246	Updating parameters... 24%
1247	Updating parameters... 26%
1248	Updating parameters... 28%
1249	Updating parameters... 30%
1250	Updating parameters... 32%
1251	Updating parameters... 34%
1252	Updating parameters... 36%
1253	Updating parameters... 38%
1254	Updating parameters... 40%
1255	Updating parameters... 42%
1256	Updating parameters... 44%
1257	Updating parameters... 46%
1258	Updating parameters... 48%
1259	Updating parameters... 50%
1260	Updating parameters... 52%
1261	Updating parameters... 54%
1262	Updating parameters... 56%
1263	Updating parameters... 58%
1264	Updating parameters... 60%
1265	Updating parameters... 62%
1266	Updating parameters... 64%
1267	Updating parameters... 66%
1268	Updating parameters... 68%
1269	Updating parameters... 70%
1270	Updating parameters... 72%
1271	Updating parameters... 74%
1272	Updating parameters... 76%
1273	Updating parameters... 78%
1274	Updating parameters... 80%
1275	Updating parameters... 82%
1276	Updating parameters... 84%
1277	Updating parameters... 86%
1278	Updating parameters... 88%
1279	Updating parameters... 90%
1280	Updating parameters... 92%
1281	Updating parameters... 94%
1282	Updating parameters... 96%
1283	Updating parameters... 98%
1284	Updating parameters... 100%
1285	Reset done. Reconnect the device to the HART - otherwise there might be data inconsistence.
1286	Reset device now?
1287	Resetting... %{l_iProcessPercent}%
1288	Factory Reset done. Reconnect the device to the HART - otherwise there might be data inconsistence.
1289	Master Reset done. Reconnect the device to the HART - otherwise there might be data inconsistence.
1290	No event to acknowledge!
1291	Event is acknowledged!
1292	Event cannot be acknowledged!
1293	No help needed!
1294	Relay is in normal state.
1295	Relay is in alarm state.
1296	Select new relay state...
1297	Normal-State;Alarm-State;Abort
1298	Refresh Plateau data?
1299	No Plateau data available
1300	Refreshing Plateau record No. ... %{i_Rec}
1301	Plateau records refreshed.
1302	Reset Event Log now?
1303	Yes;Cancel
1304	Resetting Event Log... %{l_iProcessPercent}%
1305	********
1306	Event Log reset done!
1307	Refresh Event Log?
1308	Refreshing Event Log... %{l_iProcessPercent}%
1309	F
1310	S
1311	C
1312	M
1313	100
1314	101
1315	102
1316	103
1317	104
1318	105
1319	106
1320	107
1321	108
1322	109
1323	110
1324	111
1325	112
1326	113
1327	114
1328	115
1329	116
1330	117
1331	118
1332	119
1333	120
1334	121
1335	122
1336	123
1337	200
1338	201
1339	202
1340	203
1341	204
1342	205
1343	206
1344	207
1345	300
1346	301
1347	302
1348	303
1349	304
1350	305
1351	306
1352	307
1353	308
1354	309
1355	310
1356	311
1357	312
1358	313
1359	314
1360	315
1361	316
1362	317
1363	318
1364	319
1365	320
1366	321
1367	322
1368	323
1369	400
1370	401
1371	402
1372	403
1373	404
1374	405
1375	406
1376	407
1377	408
1378	409
1379	410
1380	411
1381	412
1382	413
1383	414
1384	415
1385	416
1386	417
1387	418
1388	419
1389	420
1390	421
1391	422
1392	423
1393	500
1394	501
1395	502
1396	503
1397	504
1398	505
1399	506
1400	507
1401	600
1402	601
1403	602
1404	603
1405	604
1406	605
1407	606
1408	607
1409	700
1410	701
1411	702
1412	703
1413	704
1414	705
1415	706
1416	707
1417	800
1418	801
1419	802
1420	803
1421	804
1422	805
1423	806
1424	807
1425	900
1426	901
1427	902
1428	903
1429	904
1430	905
1431	906
1432	907
1433	Event Log refresh done.
1434	Select event group to refresh:
1435	Refresh %{var_ds_eErrorCounterGroup} ?
1436	Refreshing %{var_ds_eErrorCounterGroup}... %{l_iProcessPercent}%
1437	%{var_ds_eErrorCounterGroup} refresh done.
1438	Reset event counter now?
1439	Resetting event counter... %{l_iProcessPercent}%
1440	Event counter reset done!
1441	Refresh module table from device?
1442	Refreshing... %{l_iProcessPercent}%
1443	Module table refresh done.
1444	Set Polling Address
1445	Set HV mode to manual?
1446	HV mode has changed
1447	Set HV mode to automatic?
1448	Plateau measurement is running. Abort Plateau measurement?
1449	Plateau measurement aborted
1450	Start Plateau measurement?
1451	Plateau measurement is running... Parameter HV_Mode is signaling actual status.
1452	WARN - This action will overwrite your measurement configuration!
1453	Performing calibration... 0%
1454	Performing calibration... 7%
1455	Performing calibration... 14%
1456	Performing calibration... 21%
1457	Performing calibration... 28%
1458	Performing calibration... 38%
1459	Performing calibration... 45%
1460	Performing calibration... 52%
1461	Performing calibration... 59%
1462	Performing calibration... 66%
1463	Performing calibration... 72%
1464	Performing calibration... 78%
1465	Performing calibration... 84%
1466	Performing calibration... 90%
1467	Performing calibration... 100%
1468	Calibration aborted. Code: %{var_ds_eCalibrationStatus} Check help and instruction!
1469	Calibration was performed successfully!
1470	WARN - Be aware that PV alarm setup must be adapted to changed measurement configuration!
1471	WARN - This action will overwrite your measurement settings!
1472	Performing restore... 0%
1473	Performing restore... 7%
1474	Performing restore... 14%
1475	Performing restore... 21%
1476	Performing restore... 31%
1477	Performing restore... 38%
1478	Performing restore... 45%
1479	Performing restore... 52%
1480	Performing restore... 59%
1481	Performing calibration... 65%
1482	Performing restore... 74%
1483	Performing restore... 82%
1484	Performing restore... 90%
1485	Performing restore... 100%
1486	Restore aborted. Code: %{var_ds_eCalibrationStatus} Help: %{var_ls_eCalibrationStatusHelp}. Instruction: %{var_ls_eCalibrationStatusInstruction}.
1487	Calibration was performed successfully
1488	WARN - All calibration parameters will be overwritten with the actual used measurement parameters!
1489	Performing recall... 0%
1490	Performing recall... 10%
1491	Performing recall... 20%
1492	Performing recall... 30%
1493	Performing recall... 45%
1494	Performing recall... 60%
1495	Performing recall... 80%
1496	Performing recall... 90%
1497	Performing recall... 100%
1498	A Copy of measuring data wa successfully loaded to calibration parameter!
1499	Read-in is still active!
1500	Read-in - calibration point %{l_iCalPoint} Rate = %{0} cps Remaining Time = %{1} s
1501	Read-in finished.
1502	Calibration point rate has to be greater than background rate!
1503	Read-in is still active
1504	Read-in - background rate Rate = %{1} cps Remaining Time = %{0} s
1505	Read-in aborted!
1506	Clear calibration table?
1507	Clearing... (Cal Point No.: %{l_iItem})
1508	Calibration table cleared.
1509	Nothing to edit in this mode!
1510	Select cal. point
1511	Point-1
1512	Point-1;Point-2
1513	Point-1;Point-2;Point-3;Point-4;Point-5;Point-6;Point-7;Point-8;Point-9;Point-10;Point-11
1514	Device is offline!
1515	Refreshing table... 21%
1516	Refreshing table... 28%
1517	Refreshing table... 38%
1518	Refreshing table... 45%
1519	Refreshing table... 52%
1520	Refreshing table... 59%
1521	Refreshing table... 66%
1522	Refreshing table... 68%
1523	Refreshing table... 70%
1524	Refreshing table... 78%
1525	Refreshing table... 84%
1526	Refreshing table... 90%
1527	Refreshing table... 100%
1528	Table update succeeded!
1529	Cleaning up wizard... 0%
1530	Cleaning up wizard... 25%
1531	Cleaning up wizard... 50%
1532	Cleaning up wizard... 75%
1533	Cleaning up wizard... 100%
1534	Cannot run wizard cleanup cause device is in write protect mode!
1535	Unexpected error occured during device configuration! - Check configuration input parameters - Check device communcication - Try again
1536	Unexpected error occured during device calibration! - Check configuration input parameters - Check device communcication - Try again
1537	Unexpected error occured during device recall procedure! - Check configuration input parameters - Check device communcication - Try again
1538	Welcome to the LB414 SmartSeries Wizard! This wizard automates the most common tasks involving the device setup. Click "OK" button to proceed...
1539	Wizard loading ...
1540	Loading...
1541	Would you like to run new calibration or recall actual measurement parameter set?
1542	New;Recall;Abort
1543	Change system Date? %{0} (mm/dd/yyyy)
1544	Skip;Edit;Back;Abort
1545	System Date (mm/dd/yyyy) Set day...
1546	l_iDay
1547	Change system Date %{0} (mm/dd/yyyy) Edit day...
1548	System Date (mm/dd/yyyy) Set month...
1549	l_iMonth
1550	Change system Date %{0} (mm/dd/yyyy) Edit month...
1551	System Date (mm/dd/yyyy) Set year...
1552	l_iYear
1553	Change system Date %{0} (mm/dd/yyyy) Edit year...
1554	Change system Time? %{0} (hh:mm:ss)
1555	Set system Time %{0} (hh:mm:ss)
1556	Change detector type? %{0}
1557	Edit detector type... %{0}
1558	Change nuclide? %{0}
1559	Edit nuclide... %{0}
1560	Change measurement mode? %{0}
1561	Skip;DENSITY;CONCENTRATION;SOLIDS CONTENT;Back;Abort
1562	Change system unit? %{0}
1563	Skip;g/cm³;kg/m³;lb/gal;lb/ft³;g/l;SGU;Back;Abort
1564	PV unit is constantly fixed to %{0}
1565	Continue;Back;Abort
1566	Change calibration method? %{0}
1567	Skip;DIRECT;1-POINT;2-POINT;MULTIPOINT;Back;Abort
1568	Skip;DIRECT;1-POINT;MULTIPOINT;Back;Abort
1569	Select number of calibration points?
1570	3-POINTS;4-POINTS;5-POINTS;6-POINTS;7-POINTS;8-POINTS;9-POINTS;10-POINTS;11-POINTS;Back;Abort
1571	2-POINTS;3-POINTS;4-POINTS;5-POINTS;6-POINTS;7-POINTS;8-POINTS;9-POINTS;10-POINTS;11-POINTS;Back;Abort
1572	Change measuring path? %{0} %{1}
1573	Invalid Measuring Path value!
1574	Edit measuring path... %{0} %{1}
1575	Invalid measuring path value!
1576	Would you like to read-in pulse rates automatically?
1577	Yes;No;Back;Abort
1578	Edit read-in Time... %{0} s
1579	Invalid read-in Time!
1580	Change background rate? %{0} cps
1581	Edit background rate... %{var_lf_CountRate} cps
1582	Invalid background rate!
1583	Ready to start background read-in?
1584	Yes;Skip;Back;Abort
1585	Ready to enter calibration points?
1586	Edit calibration point value #%{0}... %{1} %{2}
1587	Edit calibration point rate #%{0}... %{1} cps
1588	Calibration point rate has to be greater than background rate!
1589	Ready to start calibration points Read-in?
1590	Change calibration point #%{0}? %{1} %{2} %{3} cps
1591	Read-in;Skip;Abort
1592	Edit calibration point #%{0}... %{1} %{2}
1593	Ready to enter coefficients?
1594	Yes;Back;Abort
1595	Ready to enter coefficient?
1596	Enter coefficient directly?
1597	Edit coefficient #%{0}... %{1}
1598	l_fValue
1599	Edit coefficient #%{0}... %{1} cm²/g
1600	Edit coefficient #%{0}... %{1} cm4/g²
1601	Edit coefficient #%{0}... %{1} 1/cm
1602	Enter Abs.Coefficient %{0} cm²/g
1603	Invalid Abs.Coefficient value!
1604	Edit Abs.Coefficient... %{var_lf_COEFF_Value} cm²/g
1605	Enter liquid density %{0} %{1}
1606	Invalid liquid density value!
1607	Edit liquid density... %{0} %{1}
1608	Enter solid density %{0} %{1}
1609	Invalid solid density value!
1610	Edit solid density... %{0} %{1}
1611	Solid density value has to be greater than liquid density value!
1612	Change lower range value (LRV)? %{0} %{1}
1613	Edit lower range value (LRV)... %{0} %{1}
1614	Change upper range value (URV)? %{0} %{1}
1615	Edit upper range value (URV)... %{0} %{1}
1616	Change damping value? %{0} s
1617	Invalid damping value!
1618	Edit damping value... %{0} s
1619	Unexpected read-in mode. Aborting Quick Start Wizard...
1620	Read-in background rate Rate = %{1} cps Remaining Time = %{2} s
1621	Read-in calibration point #%{0} Rate = %{1} cps Remaining Time = %{2} s
1622	Read-in background rate Rate = %{0} cps Read-in finished.
1623	Read-in - calibration point #%{0} Rate = %{1} cps Read-in finished.
1624	Next step will write configuration to device. Would you like to proceed?
1625	Writing configuration... 0%
1626	Writing configuration... 10%
1627	Writing configuration... 20%
1628	Writing configuration... 30%
1629	Writing configuration... 40%
1630	Writing configuration... 50%
1631	Writing configuration... 60%
1632	Writing configuration... 65%
1633	Writing configuration... 71%
1634	Writing configuration... 70%
1635	Writing configuration... 75%
1636	Writing configuration... 80%
1637	Writing configuration... 90%
1638	Writing configuration... 100%
1639	Writing to device succeeded! Would you like to proceed?
1640	Calibrate;Exit without Calibration
1641	Quick Start Wizard finished. Click "OK" button to proceed ...
1642	Performing calibration... 70%
1643	Calibration aborted. Code: %{var_ds_eCalibrationStatus} - %{var_ls_eCalibrationStatusHelp} - %{var_ls_eCalibrationStatusInstruction}
1644	Calibration was performed successfully! Quick Start Wizard finished. Click "OK" button to proceed ...
1645	Begin Write to Device
1646	Download aborted, device is in write protect mode.
1647	End Read from Device
1648	Returning Current AO to normal operation mode ...
1649	Select Current AO value ...
1650	4mA;20mA;Other;End
1651	Current AO Value
1652	Aborting method due to last error
1653	Current AO is fixed at %0 mA
1654	Connect ampere meter to Current AO ...
1655	Current AO will be fixed at 4mA !
1656	Current AO is fixed at 4mA !
1657	Aborting method due to last error...
1658	Enter ampere meter value...
1659	Is Current AO output correct? (%0 mA)
1660	Yes;No
1661	Current AO will be fixed at 20mA !
1662	Current AO is fixed at 20mA !
Reference ID	String