Device dictionary

Loading…

Reference ID	String
0	MAGNEW4W
1	Azbil Corporation
2	3.1f
3	In Status group1, show the status for Nonvolatile memory and CPU. If the status is ON, the device may be damaged. Restore power supply or contact representative of Azbil Corporation.
4	EX FAULT
5	NVM FAULT
6	RAM FAULT
7	ROM FAULT
8	A/D FAULT
9	HI<LO: High limit alarm value < Low limit alarm value. Set alarm value as Hi > Lo. Span over: Check the detector size. Set the span as the flow velocity becomes 10m/s or less. Pulse scale: Correct pulse scale. Set the pulse scale as the span frequency becomes between 0.00006Hz and 3000Hz. If engineering unit of span is volumetric, apply the volumetric unit to the pulse scale. If engineering unit of span is mass, apply the mass unit to the pulse scale. Pulse width: Set the correct pulse width to become duty 70% or less. Or set duty 50% as pulse width.
10	DO OUTPUT MODE
11	PLS OUTPUT MODE
12	AO OUTPUT MODE
13	IN CALIB MODE
14	NOT CALIBRATED
15	EX OUTPUT MODE
16	In Status group2, show the status of loop test and calibration.
17	EMPTY PIPE
18	0% LOCK
19	TYPE-DIA ERROR
20	HI<LO ALM ERROR
21	SPAN OVER ERROR
22	PLS SCALE ERROR
23	PLS WIDTH ERROR
24	Flow Sensor- Hardware that measures flow rate.
25	Pulse output- scaled frequency output from 0-1000 Hz, linear with input.
26	Gross Total- Non-resettable totalizer.
27	Net Total Value- Resettable totalizer.
28	Reverse Total- Non-resettable reverse totalizer.
29	write variables
30	Gross Total- Non-resettable totalizer
31	Net Total Value- Resettable totalizer
32	Reverse Total - Non-resettable reverse totalizer
33	Auto zero trim
34	Auto zero trim-Calibration for zero point.
35	mA
36	AO
37	.2f
38	7.4f
39	.1f
40	5.1f
41	.5f
42	6.5f
43	Puls out unit
44	m3/P
45	l/P
46	cm3/P
47	t/P
48	kg/P
49	g/P
50	B/P
51	kG/P
52	G/P
53	mG/P
54	IG/P
55	KIG/P
56	mIG/P
57	lb/P
58	m3/d
59	m3/h
60	m3/m
61	m3/s
62	l/d
63	l/h
64	l/m
65	l/s
66	cm3/d
67	cm3/h
68	cm3/m
69	cm3/s
70	t/d
71	t/h
72	t/m
73	t/s
74	kg/d
75	kg/h
76	kg/m
77	kg/s
78	g/d
79	g/h
80	g/m
81	g/s
82	BPD
83	BPH
84	BPM
85	BPS
86	kGPD
87	kGPH
88	kGPM
89	kGPS
90	IGPD
91	IGPH
92	IGPM
93	IGPS
94	KIGPD
95	KIGPH
96	KIGPM
97	KIGPS
98	mIGPD
99	mIGPH
100	mIGPM
101	mIGPS
102	GPD
103	GPH
104	GPM
105	GPS
106	mGPD
107	mGPH
108	mGPM
109	mGPS
110	lb/d
111	lb/h
112	lb/m
113	lb/s
114	Pulse Width
115	ms
116	7.2f
117	LFC value
118	Lo flo cutoff-Adjustable from 1 to 10% of the setting range. Below set value, output is driven to the zero flow rate signal level. Display is latched to zero.
119	0%
120	1%
121	2%
122	3%
123	4%
124	5%
125	6%
126	7%
127	8%
128	9%
129	10%
130	Tube size
131	Flow tube size- Nominal inside diameter of the pipe adjacent to the sensor.
132	2.5 A
133	5 A
134	8 A
135	10 A
136	13 A
137	15 A
138	20 A
139	25 A
140	32 A
141	40 A
142	50 A
143	65 A
144	80 A
145	100 A
146	110 A
147	125 A
148	150 A
149	200 A
150	250 A
151	300 A
152	350 A
153	400 A
154	450 A
155	500 A
156	600 A
157	700 A
158	800 A
159	900 A
160	1000 A
161	1100 A
162	1200 A
163	1300 A
164	1350 A
165	1400 A
166	1500 A
167	1600 A
168	1800 A
169	2000 A
170	2200 A
171	2400 A
172	2600 A
173	Totalizer Control Code- Controls the operation of all available totalizers.
174	10d
175	Totalizer display-Display totalized value.
176	9d
177	Gravity
178	Specific gravity
179	.4f
180	6.4f
181	Disp select
182	Set main display. %: Percent of range. Rate: Flow rate. Total: Totalized value.
183	%
184	Rate
185	Total
186	EX value
187	EX value: Unique detector factor.Ex factor is stamped on the name plate.
188	Coefficient
189	Set coefficient. Outputs are calculated by multiplying set coefficient. Default value is 1.0000.
190	Detector type
191	Detector type-Detector type.
192	KID
193	NNM
194	NNK
195	MGG
196	MGB
197	MGT
198	MGF
199	Burn out AO
200	Burn out AO-set burn out high, low or hold.
201	High
202	Low
203	Hold
204	Burn out Pls
205	Burn out Pls-set burn out off or hold.
206	Burn out DO1
207	Burn out DO1-set burn out open or close.
208	Close
209	Open
210	Burn out DO2
211	Burn out DO2-set burn out open or close.
212	Drop out
213	Drop out-Adjustable from 1 to 10% of the setting range. Below the set value, pulse output is cut.
214	Pls width flag
215	On to 50%, Off to 1ms between 999.99ms
216	50%
217	On
218	Total restart val
219	Total restart val-Restart value of totalizer.
220	Total prev val
221	Total preset val
222	8d
223	Hi alarm1
224	Hi alarm1-Set the upper limit value in percent of range.
225	4d
226	Hi alarm2
227	Hi alarm2-Set the upper limit value in percent of range.
228	Low alarm1
229	Low alarm1-Set the lower limit value in percent of range.
230	Low alarm2
231	Low alarm2-Set the lower limit value in percent of range.
232	Moving average
233	Moving average-Software signal processing. Apply moving average to output.
234	Off
235	Mvng av time
236	s
237	Mvng av time-Moving average time.
238	4.1f
239	Pls calib
240	5d
241	PLS output kind
242	Up
243	Down
244	SI or ALL
245	ALL
246	SI
247	Auto zero range
248	0.2 m/s
249	Release
250	Ex current FRQ1
251	Hz
252	3.125/3.75
253	6.25/7.5
254	12.5/15
255	25.0/30.0
256	Ex current FRQ2
257	3.125
258	3.75
259	5.0
260	6.25
261	7.5
262	12.5
263	15.0
264	17.5
265	22.5
266	25.0
267	27.5
268	30.0
269	75.0
270	85.0
271	115.0
272	135.0
273	S&H timing
274	1/4
275	60Hz
276	COMM mode
277	HART
278	SFN.A
279	SFN.D
280	FF
281	NONE
282	DE word length
283	4
284	6
285	Memory address
286	04X
287	08X
288	06X
289	I.OUT AO %
290	P.OUT PLS %
291	Pulse out check
292	PULSE 1
293	PULSE 2
294	EX out check
295	EXX
296	EXY
297	OFF
298	Spike cut
299	AUTO
300	MANUAL
301	OFF
302	Spike cut time
303	sec
304	Spike cut level
305	STIN check1
306	STIN check2
307	STOUT check1
308	STOUT check2
309	Done
310	In progress
311	Error
312	Flow direction
313	Forward
314	Reverse
315	Model selection
316	NORMAL
317	WATER
318	SWITCH
319	Device free condition
320	Free
321	Write protected
322	Device busy
323	Check report
324	Check OK
325	Auto zero error
326	Gain trim error
327	Auto zero and Gain trim error
328	ID check report
329	ID not defined
330	ID passd check
331	Language
332	English
333	Japanese
334	10m/s Gain Fix
335	Lo flo cutoff
336	Off
337	On
338	AC sync
339	SYNC
340	NO SYNC
341	DUMMY
342	0
343	1
344	2
345	3
346	5
347	7
348	8
349	9
350	HYSTERESIS
351	0
352	1
353	2
354	3
355	4
356	5
357	6
358	7
359	8
360	9
361	10
362	11
363	12
364	13
365	14
366	15
367	16
368	17
369	18
370	19
371	20
372	ALARM HYSTERESIS
373	PLSOUT
374	.3f
375	7.3f
376	I.out range
377	Auto
378	Wide
379	I.out limit
380	On
381	Span select
382	m/s
383	High response
384	40
385	200
386	KID coefficient
387	Func set
388	PV URV
389	11.5f
390	PV URV2
391	Date
392	Number
393	Ex value
394	mA
395	Decimal place 1
396	Decimal place 2
397	Manual zero trim
398	Pulse error; See status group 3
399	Detector type / DIA error
400	Tow few low limit data
401	Too much low limit data
402	Tow few High limit data
403	Too much High limit data
404	Low > High data
405	Too few coefficent
406	Too much coefficient
407	Too few gravity
408	Too much gravity
409	Span over 12m/s; See status group 3
410	Burn out (4mA-20mA) data
411	Burn out (PULSE) data
412	Normal contact data
413	Too few averaging time
414	Too much averaging time
415	Device is busy
416	Too few time value
417	Too much time value
418	Too few level value
419	Too much level value
420	PULSE 2 is not available.
421	Pulse output is not available. Set pulse in function set in Basic Setup menu.
422	DO1 is not available.
423	DO is not available. Set DO in function set in Basic setup menu.
424	Too few pulse coefficient
425	Too much pulse coefficient
426	DUMMY is not available.
427	Too few value
428	Too much value
429	DO2 is not available.
430	HYSTERESIS is not available.
431	ALARM HYSTERESIS is not available.
432	Span Over 12/24 m/s error
433	Invalid selection
434	Invalid digit 1
435	Invalid digit 2
436	Device Status
437	Loop test
438	Output check ST
439	Calibration
440	EX current trim
441	Factory use
442	Factory use: EX
443	Factory use: FLAG1
444	Factory use: FLAG2
445	Converter&Detector
446	Converter settings
447	Detector settings
448	Detector config
449	Conf outputs
450	Analog output
451	Pulse output
452	Totalizer
453	Digital output
454	Hart output
455	Noise immunity
456	Decimal place
457	Device info
458	Revision No.
459	Disp function
460	Reset totalizer
461	Reset totalizer-Replace the totalized value with the set value of the Total restart val.
462	D/A trim
463	D/A trim-Calibration for analog output
464	Shipping save
465	Shipping RCVR
466	Shipping data recovery-All data are set as factory default values.
467	Initial RCVR
468	Gain trim
469	Gain trim-Electrical trim.
470	Abort Gain trim
471	I.OUT D/A value
472	Abort I.OUT D/A value
473	Output check AO
474	Output check of analog current
475	Abort Output check AO
476	Output check Pls
477	Output check of pulse output
478	Abort Output check Pls
479	Output check EX
480	Output check of excitation current
481	Abort Output check EX
482	Output check DO
483	Output check of digital status output
484	Abort Output check DO
485	Output check DI
486	Output check of digital status input
487	Abort Output check DI
488	Pulse width
489	Abort pulse width
490	COMM output
491	Select communication protocol.
492	Memory operate
493	Abort memory operation
494	Set DEVICE-ID
495	Abort DEVICE-ID
496	EX value-Unique detector factor.Ex factor is stamped on the name plate.
497	Dummy value
498	Hysteresis
499	Alarm hysteresis
500	CLR error history
501	Abort Zero trim
502	CAL EX current
503	Calibrate EX value
504	Abort calibrate EX value
505	FMU860
506	DT
507	DVC
508	FCX
509	AS800
510	340T
511	340C
512	344
513	Siemens Micro K
514	SITRANS L
515	SIPAN PH
516	SITRANS P
517	75SMT
518	UNIDELTA
519	8320
520	SX5100
521	TSV175
522	DMU
523	3780
524	BM70
525	8u
526	Pulse Output Unit- Engineering units that the frequency andtotalizer outputs will be displayed with.
527	??
528	Pulse Scaling Factor- Magnitude of process variable per pulse.
529	7.5f
530	6.2f
531	4.2f
532	Puls outp
533	Pulse Output Value- scaled frequency output from 0-1000 Hz, linear with input.
534	Net Total Value- Resettable totalizer value. Counts frequency output pulses while total control is turned on.
535	Gross Total Value- Non-resettable totalizer value. Counts frequency output pulses while total control is turned on. This value will be reset to 0 when the pulse scaling, line size, or units are changed.
536	Reverse Total Value- Non-resettable totalizer value. Counts frequency output pulses while total control is turned on and flow is in the reverse direction. This value will be reset to 0 when the pulse scaling, line size, or units are changed.
537	7d
538	Coil Drive Frequency- Frequency that the coils operate at.
539	6Hz
540	30Hz
541	gross_total_units
542	Pulse output units- Engineering units that the frequency and totalizer outputs will be displayed with
543	Net Total Value- Counts frequency output pulses while total control is turned on.
544	Pulse Output- Scaled frequency output from 0-1000 Hz, linear with input.
545	Pulse output value- scaled frequency output from 0-1000 Hz, linear with input
546	Totalizer units
547	Gross Total Value- Counts frequency output pulses while total control is turned on. This value will be reset to 0 when the pulse scaling, line size , or units are changed
548	Reverse Total Value- Counts frequency output pulses while total control is turned on and flow is in the reverse direction. This value will be reset to 0 when the pulse scaling, line size, or units are changed
549	Totalizer Variable- Counts pulses from frequency output and scales the value based on the pulse output scaling and units.
550	About to enter auto zero
551	The previous error was seen while trying to initiate auto zero
552	Waiting for auto zero to complete.
553	Device failure. Device may be stuck in Auto Zero.
554	Device failure in Auto Zero.
555	The previous error was seen while trying to burn eeprom
556	Auto zero passed
557	Sensor
558	Sensor Config
559	Sensor Info
560	Device Info
561	Revision #'s
562	Totalizer will be reset
563	Yes;End
564	Totalizer was reset.
565	Choose D/A trim
566	4mA;20mA;End
567	Choose DAC trim func
568	Set;End
569	DAC trim 4mA End
570	DAC trim 20mA End
571	Shippng data save Ready?
572	Saved
573	End
574	Device will be reboot, please connect again
575	Shippng data recovery Ready?
576	CAUTION: Shipping data recovery will be soon, DO NOT RETRY. Quit and re-connect 20 seconds later.
577	Initial data recovery Ready?
578	CAUTION: Initial data recovery will be soon, DO NOT RETRY. Quit and re-connect 20 seconds later.
579	Connect MagneW calibrator
580	Choose gain
581	0.0m/s;2.5m/s;10.0m/s;End
582	Set 0.0m/s on MagneW calibrator, wait 100s
583	Start gain 0.0m/s
584	Set 2.5m/s on MagneW calibrator, wait 15s
585	Start gain 2.5m/s
586	Set 10.0m/s on MagneW calibrator, wait 15s
587	Start gain 10.0m/s
588	Waiting for gain 0.0m/s to complete.
589	Waiting for gain 2.5m/s to complete.
590	Waiting for gain 10.0m/s to complete.
591	Gain trim complete
592	Gain trim ABORTED!
593	Choose I.OUT Current
594	4mA;20mA;End
595	Set another value
596	I.OUT D/A value ABORTED!
597	Choose output check analog current
598	Start;End
599	Output check AO ABORTED!
600	Choose output check pulse
601	Select another Pulse
602	Output check Pls ABORTED!
603	Choose output check excitation
604	Select another EX
605	Output check EX ABORTED!
606	Choose output check DO
607	ST.OUT1;ST.OUT2;End
608	Select another value
609	Output check DO ABORTED!
610	Choose input check DI
611	ST.IN1;ST.IN2;End
612	ST.IN1 is Close
613	ST.IN1 is Open
614	ST.IN2 is Close
615	ST.IN2 is Open
616	Output check DI ABORTED!
617	Number to DUTY 50%
618	Yes;No;End
619	Input another value
620	DUTY 50% to Number
621	Pulse width ABORTED!
622	Protocol
623	HART;SFN analog;SFN digital;FF;None;End
624	HART protocol
625	Yes;No
626	SFN analog protocol, device will be reboot
627	SFN digital protocol, device will be reboot
628	FF protocol, device will be reboot
629	None protocol, device will be reboot
630	Set memory location
631	Set memory data
632	Set another EX value
633	Out of range error
634	Set another DUMMY value
635	Set another HYSTERESIS value
636	Set another ALARM HYSTERESIS value
637	CLR error history Ready?
638	CAUTION: Clear all error historys
639	Zero trim ABORTED!
640	Choose EX value caribration
641	Calibrate EX value ABORTED!
642	Change the zero adjust value.
643	Down;Up;End
644	Confirm flow rate is zero, wait 100s
645	Auto zero complete
Reference ID	String