HART设备字典

Loading…

引用ID	字符串
0	ALT6100
1	Autrol(Duon)
2	Duon System
3	Critical Power Failure
4	Failure
5	Out of Specification
6	Function Check
7	Device Variable Simulation active
8	The device is in simulation mode and the level output is not representative of the process.
9	Non-Volatile memory Defect
10	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
11	Volatile memory Defect
12	The RAM memory check is invalid or maybe corrupt
13	Watchdog reset executed
14	A watchdog reset has been performed
15	Power Supply conditions out of range
16	The power source, supply or voltage is outside its allowable range
17	Environmental conditions out of range
18	An internal or environmental condition is beyond acceptable limits.
19	Electronic Defect
20	A hardware problem not related to the sensor has been detected.
21	Device Configuration Locked
22	Device is in write-protect or is locked
23	Status Simulation Active
24	Discrete Variable Simulation Active
25	Event Notification Overflow
26	Sub-Device List Changed
27	Duplicate Master Detected
28	Sub-Device Mismatch
29	Sub-Device with Duplicate IDs Found
30	Stale Data Notice
31	Capacity Denied
32	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
33	Bandwidth allocation pending
34	Block transfer pending
35	Radio Failure
36	External EEPROM write fail
37	Flash Access violation
38	Flash memory write fail
39	Distance Data Over limit
40	Sensor Data Over limit
41	Sensor error
42	Interface Echo Pulse not found
43	Echo Pulse not found
44	Counter limit over
45	Sensor code error
46	Oscillator Fault
47	Calibration data error
48	Thermometer error
49	External EEPROM read fail
50	Program memory CRC error
51	.3f
52	Lvl Dev fmly
53	Lvl Class
54	Lvl PDQ
55	Lvl LS
56	Lvl Fmly stat
57	8.3f
58	Lvl Update Period
59
60	7d
61	Lvl Lower trim
62	Lvl Upper trim
63	Lvl Trim support
64	Lvl Min lower trim
65	Lvl Max lower trim
66	Lvl Min upper trim
67	Lvl Max upper trim
68	Lvl Min trim diff
69	Simulate
70	Level- Level of the process measured with respect to a reference level.
71	Update Period
72	Snsr temp unit
73	Sensor Temperature Units- Engineering unit to be displayed with Sensor Temperature.
74	Temp Class
75	Temp PDQ
76	Temp LS
77	Temp Dev Stat
78	Temp USL
79	Temp LSL
80	Temp min span
81	Temp Update Period
82	Temp snsr s/n
83	Secondary Variable - Temperature Compensation
84	Level
85	Temperature
86	Select trim mode
87	Trim Mode
88	Point
89	Upper
90	Lower
91	Cleared
92	Current PV value
93	Current trim value
94	8.4f
95	Change current value to apply value for trim
96	Apply trim value
97	Invalid Unit Code
98	Device transmitter variable code
99	Xmtr Variable
100	Pri-Var
101	Sec-Var
102	Tri-Var
103	4th-Var
104	GWR Sensor Type Code
105	Selected Sensor Type
106	Coaxial Probe
107	Single Flexible Rod
108	Single Rigid Rod
109	Twin Flexible Rod
110	Twin Rigid Rod
111	Invalid Transmitter Variable Code
112	LCD mode
113	LCD Display Mode
114	Normal> All Values
115	Normal> PV Only
116	Normal> % Only
117	Normal> mA Only
118	Eng> All Values
119	Eng> PV Only
120	Engr. Xfer Fnctn
121	Linear
122	Sqar Root
123	Decimal Place
124	Auto
125	#.#### (1-4)
126	##.### (2-3)
127	###.## (3-2)
128	####.# (4-1)
129	#####. (5-0)
130	Update Failure
131	Engr. Range Unit
132	User
133	User Defined Unit
134	Engr. LRV
135	Engr. URV
136	User Defined unit
137	Change current PV to zero adjustmet value
138	Adjust value
139	Select Zero Adjust mode
140	Adjust Mode
141	Zero Adj.
142	Cut-Off Value
143	5.2f
144	Cut-OFF Mode
145	Linear
146	Zero
147	PV is
148	Distance
149	Volume
150	Interface Level
151	Interface Distance
152	Upper Thickness
153	Interface Volume
154	Tank Height
155	Probe Length
156	Probe Angle
157	Upper M. DK
158	Two Point Trim
159	Level Adjust
160	Cut PV
161	EEPROM PROTECT
162	Eng. Unit Change
163	Level Value Change
164	More Status Clear
165	Temp Unit
166	Pressure Unit
167	Volumetric flow Unit
168	Velocity Unit
169	Length Unit
170	Time Unit
171	Mass & Mass Flow
172	Mass per volume
173	RngUnit
174	Autrol.GWR
175	Autrol Setup
176	LCD output
177	Dynamic Variables
178	Transmitter Status
179	Level Setup
180	PV Analog Channel Saturated
181	PV Analog Channel Fixed
182	Wireless
183	WirelessHART Device
184	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
185	Primary
186	Primary Analog Channel
187	Secondary
188	Secondary Analog Channel
189	Tertiary
190	Tertiary Analog Channel
191	Quaternary
192	Quaternary Analog Channel
193	Quinary
194	Quinary Analog Channel
195	Lock all
196	Trim not supported
197	Configuration cannot be changed
198	Locked by gateway
199	Analog Input Channel
200	Analog Output Channel
201	Secondary Analog Channel Saturated
202	Tertiary Analog Channel Saturated
203	Quaternary Analog Channel Saturated
204	Quinary Analog Channel Saturated
205	Secondary Analog Channel Fixed
206	Tertiary Analog Channel Fixed
207	Quaternary Analog Channel Fixed
208	Quinary Analog Channel Fixed
209	Simulation active
210	Non-Volatile memory failure
211	Volatile memory error
212	Voltage conditions out of range
213	A voltage condition is outside its allowable range
214	Electronic failure
215	Subdevice list changed
216	Duplicate master detected
217	Battery life
218	Percent range
219	Loop current
220	Primary variable
221	Secondary variable
222	Tertiary variable
223	Quaternary variable
224	Read receive time
225	Write date and time
226	Non-Volatile Clock
227	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
228	Clock Uninitialized
229	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
230	None
231	No restrictions
232	SI Only
233	Restricted to SI Unit codes only
234	Process automation device
235	Discrete device
236	Hybrid:Process automation+discrete
237	I/O System
238	WirelessHART Process automation device
239	WirelessHART Discrete device
240	WirelessHART Process automation+discrete
241	WirelessHART Gateway
242	WirelessHART Access point
243	WirelessHART Process adapter
244	WirelessHART Discrete adapter
245	WirelessHART enabled handheld/portable maintenance tool
246	Device Profile
247	US
248	United States of America
249	JP
250	Japan
251	DE
252	Germany
253	FR
254	France
255	ES
256	Spain
257	RU
258	Russian Federation
259	CN
260	People's Republic of China
261	Secondary Master
262	Primary Master
263	Device Diagnostic Status 0
264	Device Diagnostic Status 1
265	I/O and Subdevice Status
266	WirelessHART Status
267	Time Set Option
268	Real Time Clock Flags
269	Country
270	Country of intended device installation
271	SI Unit Control
272	Indicates if device should only display SI unit codes
273	Time Stamp
274	Relative time value on network
275	8u
276	Dynamic Variables Returned for Device Variables
277	Command Response Truncated
278	Configuration Change Counter Mismatch
279	Status bytes mismatch
280	Warning - Loop Should be removed from automatic control
281	Warning - This will affect sensor calibration
282	Trim Menu
283	Lower Trim;Upper Trim;Factory Recall;Exit
284	%0 Trim Point Lower : %1 Upper : %2
285	Is pressure stable? Measured (PV) : %0[%1]
286	Apply trim point?
287	NO;YES
288	Writing apply value
289	Now processing Update trim point Please wait...
290	%0 Trim Value Current : %1 Applied : %2
291	Adjust Menu
292	Level Adjust;Adjust Recall;Exit
293	Input to the Adjust Value
294	Complete Level Adjustment. Current PV : %0 [%1]
295	This Function don't works if the 'PV_is_Mode' value is set to the 'Level'.
296	Complete Adjustment Recall.
297	Cut PV Status Mode : %0 Value : %1 [%]
298	Change Cut PV ?
299	Select Cut PV mode
300	Write Cut PV Value Range : 0 - 20 [%]
301	Changed Cut PV Mode : %0 Value : %1 [%]
302	Current EEPROM Mode
303	Can't change EEPROM Protect Mode %0
304	Changed EEPROM Mode %0
305	Select unit section
306	Temperature; Pressure; Volumetric Flow; Velocity; Volume; Length; Time; Mass & Mass Flow; Mass per Volume; User Defined Unit
307	Temperature Unit
308	Volumetric Flow
309	Velocity
310	Length
311	Time
312	Mass per Volume
313	Input User Defined Unit
314	Eng. Unit Changed.
315	Change Level Parameter ?
316	Changed Level Parameters Tank Height : %0 Probe Length : %1 Probe Angle : %2
317	Complete more status clear
引用ID	字符串