Device dictionary

Loading…

Reference ID	String
0	AS700
1	AS800
2	all measurement values
3	Invalid float format
4	current out of range
5	EEPROM-Access-Error
6	CONFI-DATA-EEPROM cross sum error
7	SENSOR-DATA-EEPROM cross sum error
8	incorrect EEPROM-Marker
9	EEPROM-Restorations counter
10	EEPROM-Restoration
11	5u
12	Counter for incorrect HART-Frames
13	TIME OUT Counter
14	Counter of HART GAP Errors
15	Gap Error Counter
16	Counter for Warmstarts
17	Warmstart Counter
18	Pressure- Measured proccess pressure in relation to a reference pressure.
19	Field Device Variable Unit- unit in which digital value, minimum span, upper range value, lower range value, lower sensor limit, upper sensor limit, lower sensor trim point and upper sensor trim point are displayed. Pressure- Measured process pressure in relation to a reference pressure.
20	Field Device Variable Value- Digital value that can change without user intervention. Pressure- Measured proccess pressure in relation to a reference pressure.
21	Percent of Range- Variable which represents the digital value with respect to the range defined by the lower range value and upper range value. For normal operating modes. This variable is always in percent. Pressure- Measured process pressure in relation to a reference pressure.
22	.1f
23	Upper Sensor Limit Value- Defines the maximum value able to be used for the upper range value. Pressure- Measured proccess pressure in relation to a reference pressure.
24	Lower Sensor Limit Value- Defines the lowest allowable value for the lower range value. Pressure- Pressure of the process with respect to a reference pressure.
25	Minimum Span Value- Defines the smallest allowable difference between the Upper Range Value and the Lower Range Value. Pressure- Measured proccess pressure in relation to a reference pressure.
26	Upper Range Value- Defines the endpoint for the analog value and the 100% point of the percent range. The upper range value also defines the operational endpoint from which the alarms for the analog output value as well as the associated digital value are taken. Pressure- Measured proccess pressure in relation to a reference pressure.
27	Lower Range Value- Defines the operational endpoint or the analog output signal and 0% of the percent range. In addition, the lower range value defines an operational endpoint from which the alarm values for the analog output as well as the associated digital value are derived. Pressure- Pressure of the process with respect to a reference pressure.
28	Damping Value- Damping time which affects both the digital and analog output values. The variable is always in seconds. Pressure- Pressure of the process with respect to a reference pressure.
29	.3f
30	6.3f
31	Flange Type- Part next to the sensor which physically connects the process to the sensor. Pressure- Pressure of the process measured with respect to a reference pressure.
32	Flange and 1/4 NPT
33	DIN 19213 and 1/4 NPT
34	DIN16288: B-G 1/2A
35	DIN16288: D-G 1/2A
36	NPT1/2 '' male thread
37	NPT1/2 '' fem. thread
38	O Ring Material- Material of the seal between the module and flange.
39	1.4571
40	1.4571/1.4404
41	Hastelloy C/1.4571
42	FEP
43	1.4435/1.4571
44	Meter Installation- Defines whether or not a meter is installed and what information is able to be seen in the display.
45	analog display
46	3 1/2 digit digital display
47	Remote Seal Type- Type of remote seal connected to the device. This is only true when only 1 remote seal is installed.
48	Flush diaphragm DN 25
49	Fl. diaphr. ANSI 1''
50	Fl. diaphragm DN 50
51	Fl. diaphr. ANSI 2''
52	Fl. diaphragm DN 80
53	Fl. diaphr. ANSI 3''
54	Ext. diaphragm DN 50
55	Ext.diaphr. ANSI 2''
56	Ext. diaphragm DN 80
57	Ext.diaphr. ANSI 3''
58	Tube RS DN25/ANSI1''
59	Tube RS DN40/1.5''
60	Tube RS DN50/2''
61	Tube RS DN80/3''
62	RS w. cap screw DN50
63	RS clamp connect.2''
64	Miniature RS G 1 A
65	Miniature RS G 1/2 A
66	Sensor Fill Fluid- Fluid in the module.
67	Fluor carbon
68	Destilled water
69	High temperature oil
70	Vegetable Oil
71	Number of Remote Seals- Number of remote seals on the device.
72	Send Warning- Sends a unit code warning to the user.
73	Send Warning
74	Sensor Serial Number- Clearly defines the sensor from which the digital value or the field device variable is primarily taken. Pressure Sensor- Hardware that measures pressure with respect to a reference pressure.
75	Lower Sensor Trim Point- Applied process pressure at which the last low sensor trim was performed. Pressure Sensor- Measured proccess pressure in relation to a reference pressure.
76	Lower sensor trim point
77	Upper Sensor Trim Point- Applied process pressure at which the last upper sensor trim was performed. Pressure Sensor- Measured proccess pressure in relation to a reference pressure.
78	Upper sensor trim point
79	Analog Output Value- Value that corresponds with the digital variable under normal operating modes. Analog Output- Measureable physical output which can change user intervention.
80	Analog Output Alarm Type- Defines how the analog output responds when the field device detects that the analog output does not correspond with the field device variable. NOTE- The digital value can be undefined. Analog Output- Measureable physical output which can change without user intervention.
81	AO alrm typ
82	Measurement Type- Type of measurement this field device is intended to be used for.
83	S 043
84	S 090
85	S 063
86	S 056
87	S 036
88	S 057
89	S 091
90	S 062
91	S 033
92	S 056 LC (LOW-COST)
93	S 036 LC (LOW-COST)
94	S 057 LC (LOW-COST)
95	Flange Material- Material of flange type.
96	Remote Seal Isolator Material- Remote seal material of the parts which come in contact with the process medium. This is only true so long only 1 remote seal is installed.
97	Sensor Isolator Material- Material of a part of the sensor which comes in contact with the process material.
98	Drain Vent Material- Material of a removable plug in the flange which can be opened to remove unwanted process medium from the sensor area.
99	Local Keys Control Mode- Controls the mode of the User Interface keys on the Field Device.
100	Sensors
101	Pressure Sensor
102	Pres sens info
103	Sens temp sensor
104	Version 1.10
105	English
106	Language of strings
107	Field Device Variable Unit- Digital unit that the variable is displayed in. Sensor Temperature- Temperature of the sensor which measures the proccess.
108	Snsr temp unit
109	Field Device Variable Value- Digital value that changes with respect to process or ambient temperature over time with no user intervention. Sensor Temperature- Temperature of the sensor wich measures the process.
110	Sensor Temperature -Temperature of the sensor which measures the proccess.
111	Tertiary Variable Unit- Digital unit that the tertiary variable is displayed in. Tertiary Variable-Variable that tracks the Digital Value representation with respect to the range defined by the Lower Range Value and Upper Range Value, for normal operating modes. All units are possible.
112	TV unit
113	Tertiary Variable Value- Digital value that changes with respect to process over time with no user intervention. Tertiary Variable-Variable that tracks the Digital Value representation with respect to the range defined by the Lower Range Value and Upper Range Value, for normal operating modes. All units are possible.
114	TV Value
115	.2e
116	TV
117	Tertiary Variable- Variable that tracks the Digital Value representation with respect to the range defined by the Lower Range Value and Upper Range Value, for normal operating modes. All units are possible.
118	Primary Variable- Primary variable of the process. Secondary Variable- Secondary variable of the process. Tertiary Variable- Tertiary variable of the process.
119	Remote Seal Fill Fluid- Type of fluid in the device's remote seal.
120	Module Range Code- code for the measurement range of the transmitter's measurement cell.
121	10mbar
122	60mbar
123	400mbar
124	2.5bar
125	16bar
126	40bar
127	100bar
128	250bar
129	600bar
130	Rated Pressure- Highest operating pressure which may be applied simultaneously to both measuring chambers.
131	Rated Pressure
132	2.5bar
133	6bar
134	25bar
135	400bar
136	63bar
137	64bar
138	160bar
139	150psi
140	300psi
141	600psi
142	1500psi
143	Performs self test on the AS800. Will reports any errors.
144	Stuck in self test
145	Self test OK
146	Master reset
147	Resets the AS800 electronics.
148	Master reset OK
149	FMU860
150	DT
151	DVC
152	FCX
153	AS800
154	340T
155	340C
156	344
157	Siemens Micro K
158	SITRANS L
159	SIPAN PH
160	SITRANS P
161	75SMT
162	UNIDELTA
163	8320
164	SX5100
165	TSV175
166	DMU
167	3780
168	BM70
169	8u
170	Field Device Variable Unit- Engineering unit to be displayed with the Digital Value representation, Minimum Span, Upper Range Value, Lower Range Value, Lower Sensor Limit, and Upper Sensor Limit. Pressure- Pressure of the process measured with respect to a reference pressure.
171	Field Device Variable Value- Digital value that changes magnitude with respect to time with no user intervention. Pressure- Pressure of the process measured with respect to a reference pressure.
172	.3g
173	.f
174	.2f
175	Percent of Range- Variable that tracks the Digital Value representation with respect to the range defined by the Lower Range Value and Upper Range Value, for normal operating modes. The units of this variable are always in percent. Pressure- Pressure of the process measured with respect to a reference pressure.
176	%
177	3.2f
178	Sensor Limit Units and Minimum Span Units- Engineering unit to be displayed with the Upper Sensor Limit, Lower Sensor Limit, and Minimum Span. Pressure- Pressure of the process measured with respect to a reference pressure.
179	Upper Sensor Limit Value- Defines the maximum useable value for the Upper Range Value. Pressure- Pressure of the process measured with respect to a reference pressure.
180	Lower Sensor Limit Value- Defines the minimum useable value for the Lower Range Value. Pressure- Pressure of the process measured with respect to a reference pressure.
181	Minimum Span Value- Defines the smallest allowable difference between the Upper Range Value and the Lower Range Value. Pressure- Pressure of the process measured with respect to a reference pressure.
182	Pres xfer fnctn
183	Transfer Function- Defines the transformation function that will be applied from the Field Device Variable to the Analog Output, and Percent Range. The Transfer Function does not affect the Digital Value representation. Pressure- Pressure of the process measured with respect to a reference pressure.
184	Range Unit- Engineering unit to be displayed with the Upper Range Value and Lower Range Value. Pressure- Pressure of the process measured with respect to a reference pressure.
185	Upper Range Value- Defines the operational endpoint from which the Analog Value, and the 100% point of the Percent Range are derived. In addition, the Upper Range Value defines an operational endpoint which the alarms associated with the Analog Value, and the alarms associated with the Digital Value representation are derived. Pressure- Pressure of the process measured with respect to a reference pressure.
186	Lower Range Value- Defines the operational endpoint from which the Analog Value, and the 0% point of the Percent Range are derived. In addition, the Lower Range Value defines an operational endpoint which the alarms associated with the Analog Value, and the alarms associated with the Digital Value representation are derived. Pressure- Pressure of the process measured with respect to a reference pressure.
187	Damping Value- Damping time constant applied to both the Digital Value representation and Analog Value of the respective Analog Output. The units of this variable are always in seconds. Pressure- Pressure of the process measured with respect to a reference pressure.
188	s
189	4.2f
190	Flange Type- Hardware, adjacent to the sensor, that physically connects the process to the sensor. Pressure- Pressure of the process measured with respect to a reference pressure.
191	O Ring Material- Construction material of a seal that exists between the module and flange.
192	Meter Installation- Defines whether there is a meter installed or not and possibly what information the meter will display.
193	Remote Seal Type- Type of device that is capable of detecting and passing on the process pressure on to the module. This is only unambiguous if 1 remote seal is installed.
194	Sensor Fill Fluid- Fluid material in the module.
195	Number of Remote Seals- Physical quantity of the seals for the remote seal that is installed.
196	Send warning
197	Send Warning- Yields a units code notice to the User.
198	Variables which use this as the units code will be in the previous units until this value is sent to the device.
199	Analog Output Value- Value that tracks the Digital Value representation, under normal operating modes. Analog Output- Measureable physical output which changes with respect to time, without user intervention.
200	5.3f
201	Analog Output Alarm Type- Defines how the Analog Output will respond when the Field Device detects that the Analog Output may not be tracking the associated Field Device Variable. NOTE- The Digital Value representation may not be determinate. Analog Output- Measureable physical output which changes with respect to time, without user intervention.
202	Sensor Serial Number- Uniquely identifies the sensor from which the Digital Value representation or Field Device variable is primarily derived. Pressure Sensor- Pressure hardware that measures pressure with respect to a reference pressure.
203	Measurement Type- Type of measurement application this Field Device is intended to be used with.
204	Lower Sensor Trim Point- Applied process pressure at which the last low sensor trim was performed. Pressure Sensor- Pressure hardware that measures pressure with respect to a reference pressure.
205	6.4f
206	.4f
207	Upper Sensor Trim Point- Applied process pressure at which the last upper sensor trim was performed. Pressure Sensor- Pressure hardware that measures pressure with respect to a reference pressure.
208	Flange Material- Construction material of flange type.
209	Remote Seal Isolator Material- Construction material of a part of the remote seal type that comes in contact with the process material. This is only unambiguous if 1 remote seal is installed.
210	Sensor Isolator Material- Construction material of a part of the module type that comes in contact with the process material.
211	Local Keys Control Mode- Controls the mode of the User Interface keys on the Field Device.
212	Drain Vent Material- Construction material of a removable plug that exists on the flange type that can be opened temporarily to remove unwanted process from the sensor area.
213	RAM Failure
214	ROM cross sum error
215	EEPROM-Restoration =
216	TIME OUT Counter =
217	Gap Error Counter =
218	Warmstart Counter =
219	Device maybe stuck in selftest.
220	Please wait ...
221	Master reset OK
222	Variables with this unit maintain their old value until a new unit has been sent to the device.
Reference ID	String