Loading…
Loading…
| Name | ID | Label | Description | Type | Access | Class |
|---|---|---|---|---|---|---|
| TVloopCurrentUpperEndPoint | 2EFC | AO hi end pt | Analog Output Upper Endpoint Value- Defines the upper endpoint, of the respective Analog Output, for normal operating conditions | R | Float | 64 |
| TVloopCurrentLowerEndPoint | 2EFD | AO lo end pt | Analog Output Lower Endpoint Value- Defines the lower endpoint, of the respective Analog Output, for normal operating conditions | R | Float | 64 |
| TVloopCurrentUpperLimit | 2EFE | Upper Limit Value | The maximum value of the analog signal. | R | Float | 64 |
| TVloopCurrentLowerLimit | 2EFF | Lower Limit Value | The minimum value of the analog signal. | R | Float | 64 |
| TVpercentRange | 2F00 | TV % range | Percent of range of the HART Tertiary Variable (TV); tracks the associated measured value with respect to the Lower Range Value and Upper Range Value. | R | Float | 34 |
| TVupperRange_value | 2F02 | URV | Upper Range Value- Defines the operational endpoint from which the Analog Value, and the 100% point of the Percent Range are derived. In addition, the Upper Range Value defines an operational endpoint which the alarms associated with the Analog Value, and the alarms associated with the Digital Value representation are derived. | R/W | Float | 32 |
| TVlowerRange_value | 2F03 | LRV | Lower Range Value- Defines the operational endpoint from which the Analog Value, and the 0% point of the Percent Range are derived. In addition, the Lower Range Value defines an operational endpoint which the alarms associated with the Analog Value, and the alarms associated with the Digital Value representation are derived. | R/W | Float | 32 |
| QVloopCurrent | 2F06 | QV output value | QV output value | R/W | Float | 66 |
| QVloopUnits | 2F07 | AO unit | R | Enum | 64 | |
| QVloopDamping | 2F0A | Added damp | Analog Output Added Damping Value- Damping time constant applied the Analog Output. The units of this variable are always in seconds. | R | Float | 64 |
| QVloopCurrentUpperEndPoint | 2F0B | AO hi end pt | Analog Output Upper Endpoint Value- Defines the upper endpoint, of the respective Analog Output, for normal operating conditions | R | Float | 64 |
| QVloopCurrentLowerEndPoint | 2F0C | AO lo end pt | Analog Output Lower Endpoint Value- Defines the lower endpoint, of the respective Analog Output, for normal operating conditions | R | Float | 64 |
| QVloopCurrentUpperLimit | 2F0D | Upper Limit Value | The maximum value of the analog signal. | R | Float | 64 |
| QVloopCurrentLowerLimit | 2F0E | Lower Limit Value | The minimum value of the analog signal. | R | Float | 64 |
| QVpercentRange | 2F0F | QV % range | Percent of range of the HART Quaternary Variable (QV); tracks the associated measured value with respect to the Lower Range Value and Upper Range Value. | R | Float | 34 |
| QVupperRange_value | 2F11 | URV | Upper Range Value- Defines the operational endpoint from which the Analog Value, and the 100% point of the Percent Range are derived. In addition, the Upper Range Value defines an operational endpoint which the alarms associated with the Analog Value, and the alarms associated with the Digital Value representation are derived. | R/W | Float | 32 |
| QVlowerRange_value | 2F12 | LRV | Lower Range Value- Defines the operational endpoint from which the Analog Value, and the 0% point of the Percent Range are derived. In addition, the Lower Range Value defines an operational endpoint which the alarms associated with the Analog Value, and the alarms associated with the Digital Value representation are derived. | R/W | Float | 32 |
| eOptionOnlineMode | 40DB | Online Mode? | Can the Host Application currently communicate with the field device? | R/W | Enum | 4096 |
| eOptionValidityDebug | 40DC | Show parameters | Select: Show always all parameters or only those actually valid. For debugging purposes only. | R/W | Enum | 4096 |
| st16VersionDd | 40DE | DD-Version | Version number of the device description according to NAMUR recommendation. You are currently working with version: 01.12 | R/W | ASCII | 4096 |
| OptionConversion | 4122 | Select Conversion | Create a new table for either volume, mass or a linearoized value (Fct. C3.1.3) | R/W | Index | 0 |
| DistancePartial | 4124 | Partial Distance | Enter distance for partial empty spectrum | W | Float | 0 |
| TypeEmptySpectrum | 4125 | Empty Spectrum Type | Select the type of empty spectrum to be recorded | W | Enum | 0 |
| HeightTank | 4126 | Tank Height | Enter the tank height. (Fct. C1.2) | R/W | Float | 0 |
| TrackingVelocity | 4180 | Tracking Velocity | Tracking Velocity describes the rate of change of distance/level in the tank. (Fct. C2.1) | R/W | Float | 0 |
| AntennaExtension | 4127 | Antenna Extension | (Fct. C1.8) | R/W | Float | 0 |
| AntennaType | 4128 | Antenna Type | Select the antenna type installed on the device. (Fct. C1.7) | R/W | Enum | 0 |
| Backlight | 412A | Backlight | (Fct. C6.2) | R/W | Enum | 0 |
| BlockingDistance | 412B | Blocking Distance | The blocking distance (high) is the minimum measurement value (Fct. C1.5) | R/W | Float | 0 |
| DateCalibration | 412C | Calibration Date | Calibration date. Format according to ISO 8601. (Fct. C7.1.9) | R | HartDate | 0 |
| DateProduction | 412D | Production Date | Production date. Format according to ISO 8601. (Fct. C7.1.8) | R | HartDate | 0 |
| DeviceName | 412E | Device Name | Name of the device (Fct. C7.1.3) | R | ASCII | 0 |
| DiameterStillwell | 412F | Stilling Well Diameter | Enter the stilling well diameter (Fct. C1.4) | R/W | Float | 0 |
| DistancePiece | 4130 | Distance Piece | (Fct. C1.9) | R/W | Float | 0 |
| EpsilonRGas | 4131 | Epsilon R Gas | The gas phase permitity is used for compensating level values. (Fct. C2.3) | R/W | Float | 0 |
| EpsilonRProduct | 4132 | Epsilon R Product | The product permitivity is used in TBF mode. (Fct. C2.2) | R/W | Float | 0 |
| ErrorDelayOutputCurrentA | 4133 | Error Delay | Delay between error detection and set of error output (Fct. C4.1.6) | R/W | Enum | 0 |
| ErrorDelayOutputCurrentB | 4134 | Error Delay | (Fct. C4.2.6) | R/W | Enum | 0 |
| FactorExtSensorCalibration | 4135 | Corr. Factor Ext | (Fct. D3.3.8) | R | Float | 0 |
| FactorManSensorCalibration | 4136 | Man. Corr. Factor | (Fct. D3.3.2) | R/W | Float | 0 |
| FactorMidSensorCalibration | 4138 | Corr. Factor Mid | (Fct. D3.3.6) | R | Float | 0 |
| FactorSensorCalibration | 4139 | Corr. Factor | (Fct. D3.3.4) | R | Float | 0 |
| FormatMeasurementDisplayLine1Page1 | 413A | Format 1st Value | Select the format for the first measurement line (Fct. C6.4.5) | R/W | Enum | 0 |
| FormatMeasurementDisplayLine1Page2 | 413B | Format 1st Value | Select the format for the first measurement line (Fct. C6.5.5) | R/W | Enum | 0 |
| FormatMeasurementDisplayLine2Page1 | 413C | Format 2nd Value | Select the format for the second measurement line (Fct. C6.4.7) | R/W | Enum | 0 |
| FormatMeasurementDisplayLine2Page2 | 413D | Format 2nd Value | Select the format for the second measurement line (Fct. C6.5.7) | R/W | Enum | 0 |
| FormatMeasurementDisplayLine3Page1 | 413E | Format 3rd Value | Select the format for the third measurement line (Fct. C6.4.9) | R/W | Enum | 0 |
| FormatMeasurementDisplayLine3Page2 | 413F | Format 3rd Value | Select the format for the third measurement line (Fct. C6.5.9) | R/W | Enum | 0 |
| FreeUnitFactorLength | 4140 | Factor | (Fct. C7.5.2.3) | R/W | Float | 0 |
| FreeUnitFactorMass | 4141 | Factor | (Fct. C7.5.6.3) | R/W | Float | 0 |
| Name | ID | Label | Description | Type | Access | Class |