Loading…
Name ID Label Description Type Access Class
cFlowRateUnits 4000 Flow Rate Units Field Device Variable Unit- Engineering unit to be displayed with the Digital Value representation, Minimum Span, Upper Range Value, Lower Range Value, Lower Sensor Limit, and Upper Sensor Limit R/W Enum 8
rFlowRateValue 4027 V TBD R Float 10
rFlowRateUpperSensorLimit 4028 USL TBD R Float 8
rFlowRateLowerSensorLimit 4029 LSL TBD R Float 8
rFlowRateMinimumSpan 402A Min span TBD R Float 8
rFlowRateDampingValue 402B Damping TBD R Float 8
cFlowRateClassification 402C R Enum 2048
cFlowRateDataQuality 402D R Integer 10
cFlowRateLimitStatus 402E R Integer 10
cFlowRateDeviceFamilyStatus 402F R Integer 10
sensor_serial_number 4030 PV Snsr s/n Sensor Serial Number- Uniquely identifies the sensor from which the Digital Value representation or Field Device variable is primarily derived. R Unsigned 2048
cTotalUnits 4031 Units Field Device Variable Unit- Engineering unit to be displayed with the Digital Value representation, Minimum Span, Upper Range Value, Lower Range Value, Lower Sensor Limit, and Upper Sensor Limit R Enum 8
rTotal_1Value 4032 Total 1 (V) TBD R Float 10
rTotal_2Value 4033 Total 2 (V2) TBD R Float 10
rTotal_3Value 4034 Total 3 (SV) TBD R Float 10
rUnitConvFactor 4035 m dim TBD R Float 8
rPipeDiameter 4024 DN Pipe Diameter of the Tranmsitter R/W Float 2048
rLowFlowSuppression 4011 LFS Deterines the threshold value above which the flow totalizer is active.This setting is a percentage of the full-scale rate Qmax R/W Float 32
wAverage 4014 Average Determines the number of individual measurements required for the value calculation, i.e. determines the response time of the display. R/W Enum 8
wPipeDetect 4015 Pipe Detect Enables or Disables the internal Empty Pipe Detection which suppresses erroneous flow measurement caused by a partially empty flow tube. R/W Enum 8
wOutputMode 4016 Output Mode Determines the operation of the pulse outputs. R/W Integer 1024
wCurrentMode 401A Current mode Determines the electrical characteristic of the analog output. R/W Enum 2048
wStandbyMode 401B Standby Mode Reduces power consumption during metering pauses by turnin off meter coil excitation current. R/W Enum 2048
wParMode 400F Parameter Mode Security function for the parameters which allows the parameters to be protected agains unauthorized changes. R/W Enum 2048
rQmax 4036 Qmax Determines the scaling of the analog output, 100% Qmax = 20 mA. R/W Float 8
rIMP1Pulses 400A pv1 Determines the number of pulses per volume unit seen at output IMP1. Value pv1 is used when several channels are available. R/W Float 512
rIMP2Pulses 4012 pv2 Determines the number of pulses per volume unit seen at output IMP2. Only inflow is possible at Output-mode 1.5. R/W Float 512
wIMP1OnTime 401C tp1 Determines the maximum ON time duration for the pulse output IMP1. R/W Integer 512
wIMP2OnTime 401D tp2 Determines the maximum ON time duration for the pulse output IMP2. R/W Integer 512
wIMP3OnTime 401E Meter Out Damp (tp3) Damping of optional analog output 0/4-20 mA. R/W Integer 512
wIN1Debounce 401F it1 Debouncing time Minimum ON time duration required at the digital input IN1 to recognize a valid input. R/W Integer 1024
wIN2Debounce 4020 it2 Debouncing time Minimum ON time duration required at the digital input IN2 to recognize a valid input. R/W Integer 1024
wIN3Debounce 4021 it3 Debouncing time Minimum ON time duration required at the digital input IN3 to recognize a valid input. R/W Integer 1024
wIN4Debounce 4022 it4 Debouncing time Minimum ON time duration required at the digital input IN4 to recognize a valid input. R/W Integer 1024
wQType 4018 Q-Typ Determines whether the flow rate indication is displayed in units per Minute or per Hour such as gal/h or gal/min. R/W Enum 8
wV1Format 400D V1 Format Sets the number of digits displayed to the right of the decimal point for the display of the main totalizer V1. R/W Integer 256
wV2Format 4017 V2 Format Sets the number of digits displayed to the right of the decimal point for the display of the totalizer V2. R/W Integer 256
wDecimalPoint 4019 Decimal Pt. Selects period (.) or comma (,) as the display symbol for the decimal point. R/W Enum 256
wDisplayMode 400E Display Mode Determines whether the display unit is to be additionally checked (for trade use). R/W Enum 256
rCalConstant 4006 m spe Calibration factor: Factor serves to adjust the possible measuring deviations in the complete system. R/W Float 8
rForwardConstant 4007 p spe Separate Evaluation Factor for the positive flow. R/W Float 8
rBackwardConstant 4008 n spe Separate Evaluation Factor for the negative flow. R/W Float 8
rLowFlowConstant 4009 b spe Serves to adjust possible measureing deviations in the complete system for lower flow rates. R/W Float 8
rSpanConstant 4025 Span Calibration value of the transmitter. R/W Float 8
rOffsetConstant 4026 Offset Calibration value of the transmitter. R/W Float 8
rMinVolFactor 400B Vmin Smallest permissible measuring amount. R/W Float 8
dwChecksum 4037 eprsum Display of checksum of the program. R Integer 2048
wCalChecksum 4038 eparasum Display of checksum for the calibration data. R Integer 2048
wDataChecksum 4039 nparasum Display of checksum for the other data. R Integer 2048
wSensorType 403A Sensor Type Display of sensor types R Integer 2048
Name ID Label Description Type Access Class