Loading…
Loading…
Name | ID | Label | Description | Type | Access | Class |
---|---|---|---|---|---|---|
temperaturePDQ | 4054 | Temperature Data Quality | R | Enum | 2 | |
temperatureLS | 4055 | Temperature Limit Status | R | Enum | 2 | |
T_Status | 4056 | Temperature Status | Device Family Status- Indicates additional status information on a device variable for a specific device family. | R | BitEnum | 0 |
T_Classification | 4057 | Temperature Classification | R | Enum | 0 | |
deviceVariableFamilyCodes_Temp | 4058 | Device family | R | Enum | 0 | |
T_UpperRange_Obj_value_0 | 4059 | Temperature USL | Upper Sensor Limit Value- Defines the maximum usable value for the Upper Range Value. | R | Float | 0 |
T_LowerRange_Obj_value_0 | 405A | Temperature LSL | Lower Sensor Limit Value- Defines the minimum usable value for the Lower Range Value. | R | Float | 0 |
T_MinimumSpan_Obj_value_0 | 405B | Minimum Span | Minimum Span Value- Defines the smallest allowable difference between the Upper Range Value and the Lower Range Value. | R | Float | 0 |
T_DampingTime | 405C | Damping | Damping Value- Damping time constant applied to temperature value. The units of this variable are always in seconds. | R/W | Float | 0 |
TSim_Enable | 405D | Simulation | Temperature value simulation status. | R/W | Enum | 0 |
TmainTaskDelayTimeMax | 405E | Temperature Update Period | R | Time | 0 | |
T_transducerSerialNumber | 405F | Temperature Sensor Serial Number | Sensor Serial Number- Uniquely identifies the sensor from which the Digital Value representation or Field Device variable is primarily derived. | R | Unsigned | 0 |
swWriteProtection | 4113 | SW Write Protection | Indicates whether variables can be written to the Field Device, or whether commands that cause actions to be performed in the Field Device, can or cannot occur. | R/W | Enum | 0 |
mountOrientation | 4118 | Mounting Orientation | Device may be either Top or Bottom Mounted. | R/W | Enum | 0 |
serviceCodeLogOut | 4149 | Service Code Logout | Service Code Logout | W | Unsigned | 0 |
T_Offset_Obj_Value_0 | 40C4 | Offset | Offsets the temperature value read from the RTD at the bottom of the probe. | R/W | Float | 0 |
HartClearDiagnosticsHistory | 414C | W | Unsigned | 0 | ||
totalWorkingTimeHour | 414E | Total Run Time | Total run time in days since last device reset. | R | Unsigned | 2 |
cpuLoad | 414F | CPU Load | Percent of CPU load. | R | Float | 2 |
alarm_delay | 411A | Alarm Delay | The output will go to alarm state only if there is a loss of signal that lasts at least the duration of the alarm delay. | R/W | Float | 0 |
pulseWidth | 411B | Pulse Width | Amount of energy used for the level measurement. | R/W | Unsigned | 0 |
levelDeviceType | 4014 | Device Configuration | Options include 1 or 2 Levels and with or without Temperature. | R/W | Enum | 0 |
blanking | 406E | Blanking Distance | Blanking is a measured area which the LMT will be set to ignore including the nozzle distance. It may be necessary to extend the Blanking further past the nozzle to ignore reflections from the top portion of the probe. Blanking is set in terms of units. To adjust the Blanking, enter the distance from the Reference Measurement to be ignored. Do not blank into your measuring range. Signal will be lost. | R/W | Float | 0 |
readOnlySwitchStatus | 4114 | Status | Hardware switch that allows remote access. | R | Enum | 0 |
cbSoftwareRevisionChars | 4154 | Software Revision | Electronics software revision. | R | ASCII | 0 |
Name | ID | Label | Description | Type | Access | Class |